Page 1
HD-HU-SP-TX / HD-HU-SP-RX
HDBaseT 2.0 and USB Transmitter / Receiver
244 B
ergen Boulevard, Woodland Park, NJ 07424 • Tel 973-785-4347 •
FAX 973-785-3318 • Web:
www.fsrinc.com
43154 LIT1639A
User Manual
Page 2
Important Safety Instructions
Contents are subject to change without notice
Warnings
To reduce the risk of fire, electric shock or product damage:
1. Do not expose this device to
rain, moisture, dripping or
splashing and that no objects
filled with liquids, such as vases,
shall be placed on the unit.
6. Clean this device only
with dry cloth.
2. Do not install or place this unit
in a bookcase, built-in cabinet or
in another confined space.
Ensure the unit is well ventilated.
3. To prevent risk of electric
shock or fire hazard due to
overheating, do not obstruct
the unit’s ventilation openings
with newspapers, tablecloths,
curtains, and similar items.
4. Do not install near any heat
sources such as radiators, heat
registers, stoves, or other device
(including amplifiers) that produce
heat.
5. Do not place sources of open
flames, such as lighted candles,
on the unit.
7. Unplug this device
during lightning storms or
when unused for long
periods of time.
8. Protect cables and
cords from being walked
on or pinched particularly
at plugs.
9. Only use
attachments/accessories
specified by FSR.
10. Refer all servicing to
qualified service
personnel.
2
Page 3
Table of Contents
Overview .................................................................................................. 4
Features ................................................................................................... 5
Package Contents .................................................................................... 6
Typical Application .................................................................................... 7
Panel Layout ............................................................................................ 8
Hardware Installation.............................................................................. 16
USB Connections ................................................................................... 18
RS-232 Control and Firmware Updates ................................................. 20
Specifications ......................................................................................... 21
Page 4
Overview
Based on HDBaseT 2.0 Technology, these true HDBaseT 5-Play devices
transmit HD Video (up to 4k @60hz.), Audio, Bi-Directional Control (IR &
RS-232), Ethernet, and Bi-directional Power via 1 CAT-6A shielded cable up to
100 Meters. Long Reach Mode and increases the usable CAT6A shielded cable
length of up to150m / 492ft with up to a 1920x1080p HD video@60Hz / 24bit
Deep Color signal.
The units also carry two-way USB 2.0 on the same cable as well as an analog
audio input on the Transmitter and analog stereo audio output on the Receiver.
HDBaseT™ and the HDBaseT Alliance logo are trademarks of the HDBaseT
Alliance
4
Page 5
Features
True HDBaseT 5-Play
HDMI transmissions using single cable Cat5e cable under recommended
conditions:
90m/295ft: 4096 x 2160 video@30Hz / 24bit True Color with Chroma
subsampling color palette 4K@60Hz 4:2:0
- 100m/328ft: 1920x1080p HD video@60Hz / 36bit Deep Color
Via Cat6/6a/7 cables:
100m/328ft: 4096 x 2160 video@30Hz / 24bit True Color with
Chroma subsampling color palette 4K@60Hz 4:2:0
150m/492ft: 1920x1080p HD video@60Hz / 24bit Deep Color (Long
Reach Mode)
Bi-directional PoH (Power over HDBaseT) allowing a single power supply to
power both transmitter and receiver
Fully compliant with HDMI 1.4, and compatible with HDMI 2.0 (4K 60Hz with
4:2:0 coding)
HDCP 2.2 compliance
One analog stereo audio pass through from Transmitter in to Receiver out
over HDBaseT
Bi-directional USB pass through , USB Host/Device adjustable in both
Transmitter and Receiver
Built in 100MBase-T Ethernet Switch integral to both Transmitter and
Receiver
Audio & Video, Power, Ethernet, RS232 and IR pass-through over HDBaseT
Additional Phoenix connection power port
Dual function RS232 port for firmware update
Locking DC power connector
Cable termination follows IEEE-568B standards
5
Page 6
Package Contents
One HD-HU-SP-TX Transmitter
One HD-HU-SP-RX Receiver
One Power Supply 12VDC / 2A
Two 3.5mm Phoenix Male Connectors (2 Pin)
Two 3.5mm Phoenix Male Connectors (3 Pin)
Two IR Emitters
Two Wide-band IR Receivers (30KHz~50KHz)
Two Mounting Brackets (Pairs)
6
Page 7
Typical Application
NOTE: It is only necessary to power one side (Tx or Rx)
7
Page 8
Panel Layout
Transmitter
Front Panel
No.
Name
Description
1 SET
Enables/disables the Long Reach Mode,
RS232 updates /pass-through the device
Choose USB Device or USB Host mode
2 Power LED
ON: The transmitter is powered on
OFF: The transmitter is powered off
3 Status LED
Flashing Slowly:
The transmitter is working properly
OFF: The transmitter is not working properly
4 HDCP LED
ON: HDCP video is being transmitted
Flashing Quickly: Non-HDCP video is being
transmitted
5 Link LED
ON: HDBT link is normal
Blinking/OFF: No HDBT Link or link is unstable
8
Page 9
SET DIP switch Settings
The SET DIP switch is capable of setting the RS232 firmware update or RS232
pass through function, choosing USB device or USB Host mode and
enabling/disabling the Long Reach Mode.
NOTE: SET switches that are marked in grey indicate the switch can be in any
position.
The first switch is used for controlling the RS232:
RS232 pass through
RS232 firmware update
9
Page 10
The second switch is used for controlling the USB HOST/DEVICE mode on
the Rx and Tx Units:
NOTE: The second switch must be in the same position on both the Transmitter
and Receiver:
Set Tx Unit to be USB Host and Rx Unit to be USB Device
Note: Reboot the device to make the change effective.
Set Rx Unit to be USB Host and Tx Unit to be USB Device
Note: Reboot the device to make the change effective.
The third switch is used for controlling the Long Reach Mode. This increases
the usable CAT6A shielded cable length of up to150m/492ft when using up to a
1920x1080p HD video@60Hz / 24bit Deep Color signal.
Long Reach Mode OFF
(Set BOTH the Transmitter and Receiver to "OFF", then remove power and
reapply to activate the new setting)
Long Reach Mode ON
(Set BOTH the Transmitter and Receiver to "ON", then remove power and reapply
to activate the new setting)
10
Page 11
Rear Panel
No.
Name
Description
1 DC 12V
12V DC power input,
Threaded port for standard or locking connection
2-pin phoenix port for alternate power connection
2 HDBT OUT Connects to HDBT IN port of HDBT receiver
3 LINE IN
Analog audio input, 3.5mm analog audio pass
through from transmitter input to receiver output
over HDBaseT.
4 HDMI IN
Connects to an HDMI source
5 RS232
RS232 pass through or firmware update
6 IR RX
Connects to IR receiver to enable control of display
from source location
7 IR TX
Connects to IR emitter to enable control of source
from display location
8 USB HOST
Connects to device to be controlled such as server,
computer etc.
9 USB Device
Connects to USB devices such as mouse,
keyboard, USB disk etc.
10 ETHERNET 1
Connects to Ethernet devices
11 ETHERNET 2
Connects to Ethernet devices
11
Page 12
Receiver
Front Panel
No.
Name
Description
1
SET
Dip Switch
Enables/disables the Long Reach Mode,
RS232 updates /pass-through the device
Choose USB Device or USB Host mode
2
Power
LED
ON: The receiver is powered on
OFF: The receiver is powered off
3
Status
LED
Flashing Slowly: The receiver is working properly.
OFF: The receiver is not working properly
4
HDCP
LED
ON: HDCP video is being transmitted
Flashing Quickly:
Non-HDCP video is being transmitted
5 Link LED
ON: HDBASET link is normal
Blinking/OFF: No HDBT Link or link is unstable
12
Page 13
SET DIP switch Settings
The SET switch is capable of setting the RS232 function, choosing USB device or
USB Hose mode, enabling/disabling the Long Reach Mode.
Note: SET switches that are marked in grey indicate the switch can be in any
position.
The first switch is used for controlling the RS232:
RS232 pass through
RS232 update
The second switch is used for controlling the USB HOST/DEVICE mode on
the Rx and Tx Units:
Set Tx Unit to be USB Host and Rx Unit to be USB Device
Note: Reboot the device to make the change effective.
13
Page 14
Set Rx Unit to be USB Host and Tx Unit to be USB Device
Note: Reboot the device to make the change effective.
NOTE: The second switch must be in the same position on both the Transmitter
and Receiver:
The third switch is used for controlling the Long Reach Mode: This increases
the usable CAT6A shielded cable length of up to150m/492ft when using up to a
1920x1080p HD video@60Hz / 24bit Deep Color signal.
Long Reach Mode OFF
(Set BOTH the Transmitter and Receiver to "OFF", then remove power and
reapply to activate the new setting)
Long Reach Mode ON
(Set BOTH the Transmitter and Receiver to "ON", then remove power and reapply
to activate the new setting)
14
Page 15
Rear Panel
No.
Name
Description
1 DC 12V
12V DC power input,
-threaded port for standard or locking connection
-two-pin phoenix port for alternate power connection
2 HDBT IN Connects to HDBT OUT port of HDBT transmitter
3 LINE OUT
Analog audio output, 3.5mm analog audio pass
through from transmitter in to receiver out over HDBT.
4 HDMI OUT Connects to an HDMI display device
5 RS232
RS232 pass through or firmware update
6 IR RX
Connects to IR receiver to enable control of source
from display location
7 IR TX
Connects to IR emitter to enable control of display
from source location
8 USB HOST
Connects to device to be controlled such as server,
computer etc.
9
USB
DEVICE
Connects to USB devices such as mouse, keyboard,
USB disk etc.
10
ETHERNE
T 1
Connects to Ethernet devices
11
ETHERNE
T 2
Connects to Ethernet devices
15
Page 16
Hardware Installation
1. Using quality HDMI cables, connect an HDMI source (such as Blu-ra y,
games console, satellite/cable TV, media server etc.) to HDMI IN of the
Transmitter.
2. Connect a good quality, well terminated, shielded Catx cable between the
HDBT OUT of the Transmitter to the HDBT IN of the Receiver.
3. Connect the HDMI display device (LED/LCD display or projector) to the
HDMI OUT of the Receiver.
4. For two-way IR control of connected sources and displays from either
location, first, connect the IR Sensors to the IR IN ports of the Transmitter or
Receiver, and then insert IR Emitters into the IR OUT ports of the
Transmitter or Receiver.
5. Connect the included 12v power supply to the Transmitter power input
connector. The PoH function carries power along the length of the cable
one-way to power the Receiver. No additional power supply is required at
the display end of the cable run.
.
16
Page 17
Check Power, Status, and HDCP & Link lights are illuminated on both units to
indicate successful connection, with a lit HDCP light illustrating the presence of
encryption within the signal. Power and Link are status lights. Status should be
blinking.
17
Page 18
USB Connections
NOTE: The USB 1 and USB 2 signal paths shown above cannot be used at the
same time. Only one USB host is allowed at any one time.
SET switches that are marked in grey indicate the switch can be in any position.
Mode 1: Transmitter in USB Host Mode and Receiver in USB Device Mode
The second switch must be up on both Transmitter and Receiver:
Mode 2: Transmitter in USB Device Mode and Receiver in USB Host Mode
The second switch must be down on both Transmitter and Receiver:
18
Page 19
IR and RS-232 Operation
19
Page 20
RS-232 Control and Firmware Updates
The RS-232 port can be used as pass-through to control a device connected to
the Transmitter from the Receiver or vice versa. In addition, the RS-232 port on
the Transmitter or Receiver can be connected to a computer to update the
firmware.
20
Page 21
Specifications
Transmitter
Technical
Input
1 x HDMI IN
1 x Analog Stereo Audio IN
Input Signal Type
HDMI 1.4, and compatible with HDMI 2.0
(4K 60Hz with 4:2:0 coding)
HDCP 2.2
Input Resolution Support
800x600@60Hz, 848x480@60Hz,
1024x768@60Hz, 1280x768@60Hz,
1280x800@60Hz, 1280x960@60Hz,
1280x1024@60Hz, 1360x768@60Hz,
1366x768@60Hz, 1440x900@60Hz,
1600x900@60Hz, 1600x1200@60Hz,
1680x1050@60Hz, 1920x1200@60Hz,
2048x1152@60Hz, 3840x2160@24Hz,
3840x2160@25Hz, 3840x2160@30Hz,
3840x2160@60Hz, 4096x2160@24Hz,
4096x2160@60Hz, 720x480@60Hz (480p),
720x576@50Hz (576p),
1280x720@50Hz (720p50),
1280x720@60Hz (720p60),
1920x1080@50Hz (1080p50),
1920x1080@60Hz (1080p60)
Input Video Level 0.5~1.0Vp-p
Maximum Pixel Clock 297MHz
Output
1 x HDBT OUT
1 x S/PDIF OUT
Input Signal Type HDBT 2.0
21
Page 22
Output Resolution Support
800x600@60Hz, 848x480@60Hz,
1024x768@60Hz, 1280x768@60Hz,
1280x800@60Hz, 1280x960@60Hz,
1280x1024@60Hz, 1360x768@60Hz,
1366x768@60Hz, 1440x900@60Hz,
1600x900@60Hz, 1600x1200@60Hz,
1680x1050@60Hz, 1920x1200@60Hz,
2048x1152@60Hz, 3840x2160@24Hz,
3840x2160@25Hz,3840x2160@30Hz,
3840x2160@60Hz, 4096x2160@24Hz,
4096x2160@60Hz, 720x480@60Hz (480p),
720x576@50Hz (576p),
1280x720@50Hz (720p50),
1280x720@60Hz (720p60),
1920x1080@50Hz (1080p50),
1920x1080@60Hz (1080p60)
Video Impedance 100 Ω
Maximum Transmission
distance
Cat 5e:
1080p 36bit : 100m
4K@60Hz 4:2:0: 90m
Cat 6/6a/7:
1080p 48bit : 100m
4K@60Hz 4:2:0: 100m
Long Reach Mode:
1080p 24bit:150m
Control
Control Method
1 x IR Transmitter, 1x IR Receiver;
1 x RS232, 2 x Ethernet,
1 x USB Host, 2 x USB Device
General
Operating Temperature
0 to + 45°C (32 to + 113 °F),
10% to 90%, non-condensing
22
Page 23
Storage Temperature
-20 to +70°C (-4 to + 158 °F),
10% to 90%, non-condensing
Humidity 10% to 90%, non-condensing
Power Supply DC 12V
Power Consumption
16.08W
Transmitter supply power to Receiver
ESD Protection
Human-body Model:
±8kV(Air-gap discharge)/
±4kV(Contact discharge)
Device Dimension
(W x H x D)
271.8mm x 20mm x 98.8mm
10.70" x 0.79" x 3.89"
Product Weight 0.72kg
Certification CE, FCC, RoHS
Operating Temperature
0 to + 45°C (32 to + 113 °F),
10% to 90%, non-condensing
Storage Temperature
-20 to +70°C (-4 to + 158 °F),
10% to 90%, non-condensing
23
Page 24
Receiver
Technical
Input 1 x HDBT
Input Signal Type HDBT 2.0
Input Resolution Support
800x600@60Hz, 848x480@60Hz,
1024x768@60Hz, 1280x768@60Hz,
1280x800@60Hz, 1280x960@60Hz,
1280x1024@60Hz, 1360x768@60Hz,
1366x768@60Hz, 1440x900@60Hz,
1600x900@60Hz, 1600x1200@60Hz,
1680x1050@60Hz, 1920x1200@60Hz,
2048x1152@60Hz, 3840x2160@24Hz,
3840x2160@25Hz, 3840x2160@30Hz,
3840x2160@60Hz, 4096x2160@24Hz,
4096x2160@60Hz, 720x480@60Hz (480p),
720x576@50Hz (576p),
1280x720@50Hz (720p50),
1280x720@60Hz (720p60),
1920x1080@50Hz (1080p50),
1920x1080@60Hz (1080p60)
Input Video Level 0.5-1.0 V p-p
Input DDC Signal 5V p-p
Maximum Pixel Clock 297MHz
Output
1 x HDMI OUT
1 x Analog Stereo Audio
Output Signal Type
HDMI 1.4, and compatible with HDMI 2.0
(4K 60Hz with 4:2:0 coding)
HDCP 2.2
Output Resolution Support
800x600@60Hz, 848x480@60Hz,
24
Page 25
1024x768@60Hz, 1280x768@60Hz,
1280x800@60Hz, 1280x960@60Hz,
1280x1024@60Hz, 1360x768@60Hz,
1366x768@60Hz, 1440x900@60Hz,
1600x900@60Hz, 1600x1200@60Hz,
1680x1050@60Hz, 1920x1200@60Hz,
2048x1152@60Hz, 3840x2160@24Hz,
3840x2160@25Hz, 3840x2160@30Hz,
3840x2160@60Hz, 4096x2160@24Hz,
4096x2160@60Hz, 720x480@60Hz (480p),
720x576@50Hz (576p),
1280x720@50Hz (720p50),
1280x720@60Hz (720p60),
1920x1080@50Hz (1080p50),
1920x1080@60Hz (1080p60)
Video Impedance 100 Ω
Maximum Transmission
distance
Cat 5e:
1080p 36bit : 100m
4K@60Hz 4:2:0: 90m
Cat 6/6a/7:
1080p 48bit : 100m
4K@60Hz 4:2:0: 100m
Long Reach Mode:
1080p 24bit:150m
Control
Control method
1 x IR Transmitter, 1x IR Receiver,
1 x RS232, 2 x Ethernet,
1 x USB Host, 2 x USB Device
General
Operating Temperature 0°C to 45°C (32°F to 113°F)
Storage Temperature -20°C to 70°C (-4°F to 158°F)
Humidity 10% to 90%, non-condensing
25
Page 26
ESD Protection
Human-body Model:
±8kV(Air-gap discharge)/
±4kV(Contact discharge)
Surge Protection
Voltage: ±1 kV
(Ten times respectively for the positive and
negative voltage)
Electrical Fast
Transient/Burst
Data communication cord: 1 kV
Power cord : 2 kV
Power Supply DC 12V
Power Consumption
16.2W
Receiver supply power to Transmitter
ESD Protection
Human-body Model:
±8kV(Air-gap discharge)/
±4kV(Contact discharge)
Device Dimension
(W x H x D)
271.8mm x 20mm x 98.8mm
10.70" x 0.79" x 3.89"
Product Weight 0.72kg
Cable Specifications
Note: Use of straight-through Category cables wired to T568B standard.
Cable Type
Range
Supported Video
Cat5e 100m/328ft Up to 1080p@60Hz 36bit
90m/295ft 1080p@60Hz 48bit
1080p@60Hz 3D
4K@30Hz 4:4:4, 4k@60Hz 4:2:0
Cat6/6a/7
100m/328ft
Note:
Up to 150 meters in long-reach mode:
Up to 4 Gbps HDBT Traffic rate
HDMI Pixel Frequency 148.5Mhz
Video Format 1080p / 60Hz / 24bpp
26
Page 27
Limited Warranty
The HD-HU-SP HDBaseT HDMI Extender Set is warranted against failures due to defective
parts or faulty workmanship for a period of three years after delivery to the original owner.
During this period, FSR will make any necessary repairs or replace the unit without charge
for parts or labor. Shipping charges to the factory or repair station must be prepaid by the
owner, return-shipping charges (via UPS Ground) will be paid by FSR.
This warranty applies only to the original owner and is not transferable. In addition, it does
not apply to repairs done by other than the FSR factory or Authorized Repair Stations.
This warranty shall be cancelable by FSR at its sole discretion if the unit has been subjected
to physical abuse or has been modified in any way without written authorization from FSR.
FSR’s liability under this warranty is limited to repair or replacement of the defective unit.
FSR will not be responsible for incidental or consequential damages resulting from the use
or misuse of its products. Some states do not allow the exclusion of incidental or
consequential damages, so the above limitations may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state.
Warranty claims should be accompanied by a copy of the original purchase invoice showing
the purchase date (if a Warranty Registration Card was mailed in at the time of purchase,
this is not necessary). Before returning any equipment for repair, please read the important
information on service below.
SERVICE
Before returning any equipment for repair, please be sure that it is adequately packed and
cushioned against damage in shipment, and that it is insured. We suggest that you save the
original packaging and use it to ship the product for servicing. Also, please enclose a note
giving your name, address, phone number and a description of the problem.
NOTE: all equipment being returned for repair must have a Return authorization (RMA)
Number. To get a RMA Number, please call the FSR Service Department
(1-800-332-FSR1).
Please display your RMA Number prominently on the front of all packages.
CONTACT INFORMATION:
FSR INC.
244 Bergen Blvd.
Woodland Park, NJ 07424
Phone: (973) 785-4347
Order Desk Fax: (973) 785-4207
Web Site:
http://www.fsrinc.com
27
Page 28
Loading...