Page 1
User Manual
HD-HPC-SP-TX / HD-HPCWP-TX
100m HDBaseT HDMI and VGA 2x1 Switcher / Extender
244 Bergen Boulevard, Woodland Park, NJ 07424 Tel 973-785-4347 FAX
973-785-3318 Web: www.fsrinc.com
43106 LIT1550D
Page 2
Important Safety Instructions
Contents are subject to change without notice
Warnings
To reduce the risk of fire, electric shock or product damage:
1. Do not expose this device to
rain, moisture, dripping or
splashing and that no objects
filled with liquids, such as vases,
shall be placed on the unit.
6. Clean this device only
with dry cloth.
2. Do not install or place this unit
in a bookcase, built-in cabinet or
in another confined space.
Ensure the unit is well ventilated.
3. To prevent risk of electric
shock or fire hazard due to
overheating, do not obstruct
the unit’s ventilation openings
with newspapers, tablecloths,
curtains, and similar items.
7. Unplug this device
during lightning storms or
when unused for long
periods of time.
8. Protect cables and
cords from being walked
on or pinched particularly
at plugs.
4. Do not install near any heat
sources such as radiators, heat
registers, stoves, or other device
(including amplifiers) that
produce heat.
9. Only use
attachments/accessories
specified by FSR.
5. Do not place sources of open
flames, such as lighted candles,
on the unit.
10. Refer all servicing to
qualified service
personnel.
2
Page 3
Table of Contents
Overview .................................................................................................. 4
Features ................................................................................................... 5
Package Contents .................................................................................... 6
HD-HPC-SP-Tx and HD-HPCWP-Tx sold separately .............................. 6
HD-HPC-SP-Tx ........................................................................................ 6
Typical Application .................................................................................... 7
Typical Application .................................................................................... 8
Dimensions .............................................................................................. 9
HD-HPCWP-Tx ................................................................................. 9
HD-HPC-SP-Tx ................................................................................. 9
HD-HPC-SP-Tx Front Panel ................................................................... 10
HD-HPCWP-Tx Front Panel .................................................................... 11
................................................................................................................ 11
HD-HPC-SP-Tx Rear Panel ................................................................... 12
HD-HPCWP-Tx Rear Panel ................................................................... 13
Hardware Installation .............................................................................. 14
Input Select Button and switching behavior ............................................ 15
Dip Switch Description ........................................................................... 16
VGA EDID Switch Setting ............................................................... 16
HDMI EDID ..................................................................................... 16
SET (HD-HPC-SP-Tx only) ............................................................. 17
IR and RS-232 Operation ....................................................................... 18
IR Control ........................................................................................ 18
RS-232 Control and Firmware Updates .......................................... 20
Specifications ......................................................................................... 21
Limited Warranty .................................................................................... 23
3
Page 4
OVERVIEW
The HD-HPC-SP-Tx transmitter is a true HDBaseT 5-Play device that transmits
HD Video (up to 4k at 30Hz), Audio, Bi-directional control (IR & RS-232), Ethernet,
and Power via 1 CAT-6A shielded cable up to 100 Meters.
The HD-HPC-SP-Tx works with any of FSR’s 100 Meter HDBaseT Receivers and
can be powered from either end (Tx to Rx or Rx to Tx). The HD-HPC-SP-Tx’s
switcher has both HDMI and VGA with Audio.
The switcher has built-in auto-sensing circuitry to switch to the active source. It
can be manually triggered using the front panel Input Select Button or via contact
closure on the rear screw terminals (HD-HPC-SP-Tx only).
The HD-HPCWP-Tx is a 2-gang wallplate version of the HD-HPC-SP-Tx and fits
in a standard 2-gang box.
4
Page 5
FEATURES
Transmission distance for 1080p over Cat 5e/6 reaches up to 100 meters.
4K reaches up to 70 meters
Supports VGA input (with L/R audio) and HDMI input
Switches the input source simply by pressing the button on the front panel or
contact closure via pluggable screw terminal connector (HD-HPC-SP-Tx
only) on the rear panel
Automatically switches to an active source
HDBT 2.0 compliance
HDMI 1.4 with 4K compliance
Bi-directional PoE (HD-HPC-SP-Tx only)
Bi-directional IR
IR, Ethernet and RS232 control over HDBT
Space saving design
Note:
The actual signal transmission distance can vary and depends on signal
resolution, cable quality, graphics card, and display used in the system.
5
Page 6
PACKAGE CONTENTS
HD-HPC-SP-TX AND HD-HPCWP-TX SOLD SEPARATELY
HD-HPC-SP-TX
One HD-HPC-SP-Tx Transmitter
Two 2-pin screw-down terminals
One 3-pin screw-down terminal
One IR Emitter
One IR Receiver (30kHz ~ 50kHz)
Two Under Table Mounting Brackets
User's manual
HD-HPCWP-TX
One HD-HPCWP-TX Transmitter
One 9-pin screw-down terminal
Four 6-32x1/4 Flat head screws
One cover plate and cover plate screws
User's manual
6
Page 7
TYPICAL APPLICATION
HD-HPC-SP-Tx shown
NOTE: It is only necessary to power one side (Tx or Rx)
Transmitters do not include a Power Supply. An FSR 17762 Power Supply is
included with any of the FSR HDBaseT Receivers. Only one power supply is
needed to power the Transmitter and Receiver set. FSR 17762 Power Supplies
can also be ordered separately.
7
Page 8
TYPICAL APPLICATION
HD-HPCWP-Tx shown
Transmitter
Receiver
NOTE: Only one power supply is needed to power the Transmitter and Receiver
set from any of the FSR's 100m HDBaseT receivers. The HD-HPCWP-Tx
transmitter can be powered locally but it cannot send power to the receiver.
Transmitters do not include a Power Supply. An FSR 17762 Power Supply is
included with any of the FSR HDBaseT Receivers. FSR 17762 Power Supplies
can also be ordered separately.
8
Page 9
DIMENSIONS
HD-HPCWP-Tx
HD-HPC-SP-Tx
9
Page 10
HD-HPC-SP-TX FRONT PANEL
3
6
1 2
4
5
7
ID Name Description
1 SET RS-232 Settings (See table)
2 EDID VGA resolution settings (See table)
3 Power LED
4 Status LED
5 HDCP LED
6 Link LED
On: Unit is powered on.
Off: Unit is powered off.
Intermittent: Normal operating condition
Off: Fault
On: HDCP video is being transmitted.
Off/Intermittent: No HDCP video is being transmitted
ON: Receiver and Transmitter are linked to each other
OFF/Intermittent: Fault in unit(s) or cabling.
Input select button to select the input source.
7 Input Select
The function is the same with input select (pluggable
screw terminal connector) in the front panel. See
"Select Button and switching behavior"
10
Page 11
HD-HPCWP-TX FRONT PANEL
6
5
7
4
1
3
9
2
ID Name Description
1 VGA IN HD-15 VGA input
2 EDID VGA resolution settings (See table)
3 AUDIO Stereo audio input
4 HDMI LED Indicates HDMI input is selected
5 VGA LED Indicates VGA input is selected
6 HDCP LED
7 Link LED
8 Input Select
On: HDCP video is being transmitted.
Off/Intermittent: No HDCP video is being transmitted
ON: Receiver and Transmitter are linked to each other
OFF/Intermittent: Fault in unit(s) or cabling.
Input select button used to select the input source.
See "Select Button and switching behavior"
9 HDMI IN HDMI input
10 IR SENSOR Sensor for remote control
8
10
11
Page 12
HD-HPC-SP-TX REAR PANEL
1
2 3 4
5
6 7
8
ID Name Description
1 Power
12V 2A DC power supply input (power supply sold
separately. (See note under "Typical Application")
2 HDBT OUT Connects to HDBT IN port of receiver
3 HDMI IN Connects to an HDMI source
Pluggable screw terminal connector connecting to an
4 Input Select
external control pad (HD-HPC-SP-Tx only).
See "Select Button and switching behavior"
5 IR IN Connects to IR receiver
6 IR OUT Connects to IR transmitter
7 RS-232 Serial port (See table)
8 ETHERNET Connects to an Ethernet device
9 VGA IN Connects to a VGA source
10 Audio IN Audio input, embedded stereo in VGA audio
9 10
12
Page 13
HD-HPCWP-TX REAR PANEL
5
1
2
3
4
6
ID Name Description
1 POWER IN
12V 2A DC power supply input (power supply sold
separately. (See note under "Typical Application")
2 POWER OUT 12VDC 250mA max
3 RS-232 Serial port
4 IR OUT Connects to IR transmitter
5 ETHERNET Connects to an Ethernet device
6 HDBT OUT Connects to HDBT IN port of receiver
13
Page 14
HARDWARE INSTALLATION
Warnings
Before the installation, disconnect the power supply from all the
devices.
Do not connect or disconnect cables from the Transmitter and
Receiver while they are powered ON. To connect or disconnect
cables from the units, power them OFF first.
For best resolution and ESD performance, a shielded CAT6A in a
TIA / EIA 568B wiring configuration is recommended. Please use
care when installing, connecting and disconnecting cables.
1. Connect the source to the HDMI IN and/or VGA IN on the Transmitter.
2. Connect the IR emitter to the IR OUT and the IR Receiver to the IR IN on
both the Transmitter and Receiver.
3. Connect a Display to the HDMI OUT on the Receiver.
4. Connect the HDBT OUT on the Transmitter to the HDBT IN on the Receiver
via a shielded CAT5e / CAT6 / CAT6A / CAT7 cable.
5. Connect the power supply.
14
Page 15
INPUT SELECT BUTTON AND SWITCHING BEHAVIOR
The auto switcher will select an active input or the first-come first-served if both
inputs are active.
The input select switch or the contact closure (HD-HPC-SP-Tx only) can select
the input type only if both inputs are active.
Key function description:
1. If HDMI IN and VGA IN are both connected to the source devices, and HDMI IN
is selected as current source, pressing the input select button will switch to VGA
as source. If VGA the source is unplugged, it will switch back to HDMI IN
automatically.
2. If only HDMI IN is connected to the source device, and HDMI IN is selected as
current source, pressing the input select button will have no effect and it will
remain as HDMI IN.
15
Page 16
DIP SWITCH DESCRIPTION
VGA EDID Switch Setting
NOTE: HD-HPC-SP-TX AND HD-HPCWP-TX HAVE OPPOSITE DIP SWITCH
LOGIC FOR THE "ON" POSITION AS SHOWN BELOW:
HD-HPC-SP-TX (DOWN IS "ON") HD-HPCWP-SP-TX (DOWN IS "OFF")
ON
123
2 3
ON
Position
1
0 0 0 1280 x 800 60Hz
0 0 1 1920 x 1200 60Hz
0 1 0 1920 x 1080 60Hz (Default)
0 1 1 1280 x 720 60Hz
1 0 0 1024 x 768 60Hz
1 0 1 800 x 600 60Hz
1 1 0 Reserved
1 1 1 Reserved
0 = OFF and 1 = ON
Note:
Power cycle the extender after you change the switch position.
HDMI EDID
HD-HPC-SP-Tx: Pass-through or 1080p 60Hz if a sink is not detected.
HD-HPCWP-Tx: Pass-through
16
Position
Position
2
3
1
Resolution
Page 17
SET (HD-HPC-SP-Tx only)
1
2
3
ON
Position
1
0 0 0
1 0 0 Valens IC update
0 1 0 MCU update and control
0 = OFF (UP) and 1 = ON (DOWN)
Position
2
Position
3
Settings
RS-232 pass-through enabled
(Default)
RS-232 pass-through disabled
RS-232 pass-through disabled
17
Page 18
IR AND RS-232 OPERATION
(HD-HPC-SP-Tx shown)
IR Control
The IR pass-through feature on the Transmitter and Receiver allows you to
control the Source from the Display’s location or vice versa.
Scenario 1
The TV can be controlled from the Transmitter’s location with the TV remote.
The IR receiver is connected to the IR IN on the Transmitter and the IR emitter is
connected to the IR OUT on the Receiver.
TV REMOTE
HD-H-SP-Rx shown (ord ered seperately)
TV
IR RECEIVER
CABLE
NORMAL
UPDATE
BLUE-RAY
DVD
DC 12V
-
-
+
+
DC 12V
-
-
+
+
LOCAL OUT HDMI IN Tx RxIR IN IR OUT VGA IN L / R
HDBaseT
HDMI OUTTx Rx
IR OUTIR IN
IR EMITTER
CABLE
18
Page 19
Scenario 2
The DVD Player can be controlled from the Receiver’s location with the DVD
Player Remote. The IR emitter is connected to the IR OUT on the Transmitter and
the IR receiver is connected to the IR IN on the Receiver.
HD-H-SP-Rx
+
+
DC 12V
-
+
DC 12V
-
+
IR RECEIVER
DVD REMOTE
BLUE-RAY
DVD
LOCAL OUT HDMI IN Tx RxIR IN IR OUT VGA IN L / R
HDBaseT
HDMI OUTTx Rx
IR OUTIR IN
CABLE
TV
IR EMITTER
NORMAL
UPDATE
CABLE
19
Page 20
RS-232 Control and Firmware Updates
The RS-232 port can be used as a pass-through to control a device connected to
the Transmitter from the Receiver or vice versa. In addition, the RS-232 port on
the Transmitter can be connected to a computer to update the firmware. (See Dip
switch settings)
Scenario 1: Firmware Update
(HD-HPC-SP-Tx only)
DC 12V
-
-
+
+
LOCAL OUT
HDMI IN
IR IN
IR OUT VGA IN L / R
Tx Rx
Scenario 2: RS-232 Control
Maximum baud rate is 115.2 Kbps.
RS-232 DEVICE
DC 12V
+
+
HD-H-SP-Rx shown (ordered seperately)
DC 12V
+
+
-
-
LOCAL OUT HDMI IN Tx RxIR IN IR OUT VGA IN L / R
HDBaseT
Set switch to NORMAL
NORMAL
HDMI OUTTx RxIR OUTIR IN
RS-232 DEVICE
UPDATE
Set switch to NORMAL
20
Page 21
SPECIFICATIONS
Technical
Video input
Connectors
Input Signal Types
Output 1 HDBT
Output Signal Type HDBT
Video Impedance
Control
Control input
Maximum Pixel
Clock
Operating
Temperature
Storage
Temperature
Power Supply DC 12V 2A (power supply sold separately)
ESD Protection Human-body Model:
1 HDMI,
1 VGA (HD-15 female) with 1/8" Stereo
HDMI 1.4 and HDCP compliant up to 4K2K 30Hz
7.1ch audio
VGA + Audio up to 1920 x 1200 60Hz.
100Ω
RS-232 via 3.81mm 3 Pin pluggable screw terminal
Connector
Switch closure via 3.81mm 3 Pin pluggable screw
terminal Connector (HD-HPC-SP-Tx only)
Front Panel pushbutton switch
IR input and output via 1/8" jack (DV-HPC-SP-Tx)
IR output via 3.81mm pluggable screw terminal
297MHz
32°F to 95°F (0°C to 35°C)
10% to 90%, non-condensing
-4°F to 140°F (-20°C to 70°C)
10% to 90%, non-condensing
±8kV (Air-gap discharge)
±4kV (Contact discharge)
Surge Protection IEC 61000-4-4 (EFT) 40A (5/50ns); IEC 61000-4-5
(Lightning) 25A (8/20μs)
21
Page 22
Cable Specifications
For best resolution and ESD performance Shielded CAT6A in a TIA / EIA
568B wiring configuration is recommended.
Cable Type Range Supported Video
CAT5e/CAT6 100m 1080p 60Hz (36 bpp)
70m 1080p 60Hz (48 bpp)
1080p 60Hz 3D
4K 2160p (3840x2160 30Hz)
CAT6A/CAT7 100m 1080p 60Hz (36 bpp)
1080p 60Hz (48 bpp)
1080p 60Hz 3D
4K 2160p (3840x2160 30Hz)
General
Shipping
Weight
HD-HPCWP-Tx: 1.45 lbs. (0.66 kg)
HD-HPC-SP-Tx: 2.45 lbs. (1.12 kg)
Dimension
(W x H x D)
22
See dimension drawings for specific model information
Page 23
LIMITED WARRA NTY
The HD-HPC-SP-Tx, HD-HPCWP-SP-Tx 100m HDBaseT HDMI and VGA 2x1 Switcher /
Extender are warranted against failures due to defective parts or faulty workmanship for a
period of three years after delivery to the original owner. During this period, FSR will make
any necessary repairs or replace the unit without charge for parts or labor. Shipping charges
to the factory or repair station must be prepaid by the owner, return-shipping charges (via
UPS Ground) will be paid by FSR.
This warranty applies only to the original owner and is not transferable. In addition, it does
not apply to repairs done by other than the FSR factory or Authorized Repair Stations.
This warranty shall be cancelable by FSR at its sole discretion if the unit has been subjected
to physical abuse or has been modified in any way without written authorization from FSR.
FSR’s liability under this warranty is limited to repair or replacement of the defective unit.
FSR will not be responsible for incidental or consequential damages resulting from the use
or misuse of its products. Some states do not allow the exclusion of incidental or
consequential damages, so the above limitations may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state.
Warranty claims should be accompanied by a copy of the original purchase invoice showing
the purchase date (if a Warranty Registration Card was mailed in at the time of purchase,
this is not necessary). Before returning any equipment for repair, please read the important
information on service below.
SERVICE
Before returning any equipment for repair, please be sure that it is adequately packed and
cushioned against damage in shipment, and that it is insured. We suggest that you save the
original packaging and use it to ship the product for servicing. Also, please enclose a note
giving your name, address, phone number and a description of the problem.
NOTE: all equipment being returned for repair must have a Return authorization (RMA)
Number. To get a RMA Number, please call the FSR Service Department
(1-800-332-FSR1).
Please display your RMA Number prominently on the front of all packages.
CONTACT INFORMATION:
FSR INC.
244 Bergen Blvd.
Woodland Park, NJ 07424
Phone: (973) 785-4347
Order Desk Fax: (973) 785-4207
Web Site: http://www.fsrinc.com
23
Loading...