User Manual
HD-HPC-SP-TX
100m HDBaseT HDMI and VGA 2x1 Switcher / Extender
244 Bergen Boulevard, Woodland Park, NJ 07424 Tel 973-785-4347
FAX 973-785-3318 Web: www.fsrinc.com
43106 LIT1550
Important Safety Instructions
at plugs.
Contents are subject to change without notice
Warnings
To reduce the risk of fire, electric shock or product damage:
1. Do not expose this device to
rain, moisture, dripping or
splashing and that no objects
filled with liquids, such as vases,
shall be placed on the unit.
2. Do not install or place this unit
in a bookcase, built-in cabinet or
in another confined space.
Ensure the unit is well ventilated.
3. To prevent risk of electric
shock or fire hazard due to
overheating, do not obstruct
the unit’s ventilation openings
with newspapers, tablecloths,
curtains, and similar items.
4. Do not install near any heat
sources such as radiators, heat
registers, stoves, or other device
(including amplifiers) that
produce heat.
6. Clean this device only
with dry cloth.
7. Unplug this device
during lightning storms or
when unused for long
periods of time.
8. Protect cables and
cords from being walked
on or pinched particularly
9. Only use
attachments/accessories
specified by FSR.
5. Do not place sources of open
flames, such as lighted c andles,
on the unit.
2
10. Refer all servicing to
qualified service
personnel.
Table of Contents
Overview .............................................................................................. 4
Features ............................................................................................... 5
Package Contents ................................................................................ 6
Typical Application ................................................................................ 7
HD-HPC-SP-Tx Front Panel .................................................................. 8
HD-HPC-SP-Tx Rear Panel .................................................................. 9
Hardware Installation .......................................................................... 10
VGA EDID .......................................................................................... 12
HDMI EDID ........................................................................................ 12
SET ................................................................................................... 13
Input Select Button ............................................................................. 14
IR Control ........................................................................................... 15
Scenario 1 ................................................................................... 15
Scenario 2 ................................................................................... 16
RS-232 Control and Firmware Updates ............................................... 17
Scenario 1: Firmware Update .................................................... 17
Scenario 2: RS-232 Control ....................................................... 17
Specifications ..................................................................................... 18
Limited Warranty ................................................................................ 20
Overview
The HD-HPC-SP-Tx transmitter is a true HDBaseT 5-Play device that transmits
HD Video (up to 4k @30hz.), Audio, Bi-Directional Control (IR & RS-232),
Ethernet, and Power via 1 CAT-6A shielded cable out to 100 Meters.
The HD-HPC-SP-Tx works with any of FSR’s other 100 Meter HDBaseT
Receivers and can be powered from either end (Tx to Rx or Rx to Tx)
The HD-HPC-SP-Tx’s integral switcher has both HDMI and VGA with Audio inputs
as well as Control (IR & RS-232) and Ethernet.
The switcher has built-in auto-sensing circuitry to switch to the active source or
can be manually triggered using the front panel Input Select Button or via contact
closure on the rear screw terminals.
4
Features
Transmission distance for 1080p over Cat 5e/6 reaches up to 100 meters.
4K reaches up to 70 meters
Supports VGA input (with L/R audio) and HDMI input
Switches the input source simply by pressing the button on the front panel or
contact closure via pluggable screw terminal connector on the rear panel
Automatically switches to an active source
HDBT 2.0 compliance
HDMI 1.4 with 4K compliance
Bi-directional PoE
Bi-directional IR
IR, Ethernet and RS232 control over HDBT
Space saving design
Choice of two power inputs
Extracted audio output
Note:
The actual signal transmission distance can vary and depends on signal
resolution, cable quality, graphics card, and display used in the system.
5
Package Contents
HD-HPC-SP-Tx Transmitter:
Two 2-pin screw-down terminals
One 3-pin screw-down terminals
One IR Emitter
One IR Receiver (30kHz ~ 50kHz)
Two Mounting Ears with attaching screws (mounting hardware not
provided)
One Desktop style Power Supply 100-240 VAC to 12VDC@1A with
detachable AC cord
6
Typical Application
NOTE: It is only necessary to power one side (Tx or Rx)
7
HD-HPC-SP-Tx Front Panel
ID Name Description
1 SET RS-232 Settings (See table)
2 EDID VGA resolution settings (See table)
3 Power LED
4 Status LED
5 HDCP LED
6 Link LED
7 Input Select
On: Unit is powered on.
Off: Unit is powered off.
Intermittent: Normal operating condition
Off: Fault
On: HDCP video is being transmitted.
Off/Intermittent: No HDCP video is being transmitted
ON: Receiver and Transmitter are linked to each other
OFF/Intermittent: Fault in unit(s) or cabling.
Input select button to select the input source.
The function is the same with input select (pluggable
screw terminal connector) in the front panel.
8
HD-HPC-SP-Tx Rear Panel
ID Name Description
1 Power 12V 2A DC power supply input
2 HDBT OUT Connects to HDBT IN port of receiver
3 HDMI IN Connects to an HDMI source
Pluggable screw terminal connector connecting to an
external control pad.
Key function description:
1. If HDMI IN and VGA IN are both connected to
source devices, and HDMI IN is selected as current
4 Input Select
5 IR IN Connects to IR receiver
6 IR OUT Connects to IR transmitter
7 RS-232 Serial port (See table)
source, press the input select button, it will switch to
VGA as source; if VGA source is unplugged, it will
switch back to HDMI IN automatically.
2. If only HDMI IN is connected to source device, and
HDMI IN is selected as current source, press the
input select button, it will stay as HDMI IN.
9
ID Name Description
8 ETHERNET Connects to an Ethernet device
9 VGA IN Connects to a VGA source
10 Audio IN Audio input, embedded stereo in VGA audio
Hardware Installation
Warnings
Before the installation, disconnect the power supply from all the
devices.
Do not connect or disconnect cables from the Transmitter and
Receiver while they are powered ON. To connect or disconnect
cables from the units, power them OFF first.
For best resolution and ESD performance Shielded CAT6A in a TIA
/ EIA 568B wiring configuration is recommended. Please use care
when installing, connecting and disconnecting cables.
1. Connect the source to the HDMI IN on the Transmitter.
2. Connect the IR emitter to the IR OUT and the IR Receiver to the IR IN on
both the Transmitter and Receiver.
3. Connect a Display to the HDMI OUT on the Receiver.
4. Connect the HDBT OUT on the Transmitter to the HDBT IN on the Receiver
via a shielded CAT5e / CAT6 / CAT6A / CAT7 cable.
5. Connect the power supply to either the Transmitter or Receiver.
10
11
Dip Switch Description
VGA EDID
1 2 3
ON
Position
1
0 0 0 1280 x 800 60Hz
0 0 1 1920 x 1200 60Hz
0 1 0 1920 x 1080 60Hz (Default)
0 1 1 1280 x 720 60Hz
1 0 0 1024 x 768 60Hz
1 0 1 800 x 600 60Hz
1 1 0 Reserved
1 1 1 Reserved
0= OFF (UP) and 1=ON (DOWN)
Note:
Repower the extender after you change the switch position.
Position
2
Position
3
Resolution
HDMI EDID
Pass-through or 1080p 60Hz if a sink is not detected.
12
SET
1 2 3
ON
Position
1
0 0 X RS-232 pass-through enabled
1 0 X Valens IC update
0 1 X MCU update and control
X X 0 Reserved
X X 1 Reserved
0 0 0 Default
X = 0 or 1
0= OFF (UP) and 1=ON (DOWN)
Position
2
Position
3
Settings
RS-232 pass-through disabled
RS-232 pass-through disabled
13
Input Select Button
The auto switcher will select an active input or the first-come first-served if both
inputs are active.
The input select switch or the contact closure can select the input type only if both
inputs are active.
14
IR and RS-232 Operation
IR Control
The IR pass-through feature on the Transmitter and Receiver allows you to
control the Source from the Display’s location or vice versa.
Scenario 1
The TV can be controlled from the Transmitter’s location with the TV remote.
The IR receiver is connected to the IR IN on the Transmitter and the IR emitter is
connected to the IR OUT on the Receiver.
TV REMOTE
HD-H-SP-Rx shown (ordered seperately)
TV
IR RECEIVER
CABLE
NORMAL
UPDATE
BLUE-RAY
DVD
DC 12V
-
-
+
+
DC 12V
-
-
+
+
LOCAL OUT HDMI IN Tx RxIR IN IR OUT VGA IN L / R
HDBaseT
HDMI OUTTx RxIR OUTIR IN
IR EMITTER
CABLE
15
Scenario 2
The DVD Player can be controlled from the Receiver’s location with the DVD
Player Remote. The IR emitter is connected to the IR OUT on the Transmitter and
the IR receiver is connected to the IR IN on the Receiver.
HD-H-SP-Rx
BLUE-RAY
DVD
DC 12V
-
-
+
+
DC 12V
-
-
+
+
IR RECEIVER
DVD REMOTE
LOCAL OUT HDMI IN TxRxIR IN IR OUT VGA IN L / R
HDBaseT
HDMI OUTTxRxIR OU TIR IN
CABLE
IR EMITTER
CABLE
NORMAL
UPDATE
TV
16
RS-232 Control and Firmware Updates
The RS-232 port can be used as pass-through to control a device connected to
the Transmitter from the Receiver or vice versa. In addition, the RS-232 port on
the Transmitter or Receiver can be connected to a computer to update the
firmware. (See Dip switch settings)
Scenario 1: Firmware Update
DC 12V
-
-
+
+
LOCAL OUT HDMI IN Tx RxIR IN IR OUT VGA IN L / R
Scenario 2: RS-232 Control
HD-H-SP-Rx shown (ordered seperately)
Maximum Baud rate is 115.2 Kbps.
RS-232 DEVICE
DC 12V
-
-
+
+
DC 12V
-
-
+
+
LOCAL OUT HDMI IN TxR xIR IN IR OUT VGA IN L / R
HDBaseT
Set switch to NORMAL
NORMAL
HDMI OUTTx RxIR OUTIR IN
RS-232 DEVICE
UPDATE
Set switch to NORMAL
17
Specifications
Technical
Video input
Connectors
Input Signal Types HDMI 1.4 with 4K2K and HDCP
Input Resolution
Support
Input Video Level 0.5~1.5 Vp-p
Input DDC Signal 1.2 Vp-p
Output 1 HDBT
Output Signal Type HDBT
Video Impedance
Audio
Audio Input (via
HDMI input)
Control
1 HDMI,
1 VGA (HD-15 female)
VGA
480i, 576i, 480p, 576p, 720p@50,
720p@60,1080p@24, 1080i@25,
1080i@30, 1080p@30, 1080p@50, 1080p@60,
3840 x 2160@30, 4096 x 2160@24
100Ω
Stereo,
LPCM 5.1, LPCM 7.1;
Dolby True HD, DTS-HD Master Audio
Control input
External Audio input Stereo input via1/8” Stereo jack
Maximum Pixel
Clock
Operating
Temperature
Storage
RS-232 via 3.81mm 3 Pin pluggable screw terminal
Connector
Switch closure via 3.81mm 3 Pin pluggable screw
terminal Connector
Front Panel pushbutton switch
297MHz
32°F to 95°F (0°C to 35°C)
10% to 90%, non-condensing
-4°F to 140°F (-20°C to 70°C)
18
Temperature 10% to 90%, non-condensing
Power Supply DC 12V 2A with locking connector
Power Consumption HD-H-SP-Rx powers HD-HPC-SP-Tx (or vice
versa): ≤11.8W for both devices.
ESD Protection Human-body Model:
±8kV (Air-gap discharge)
±4kV (Contact discharge)
Surge Protection IEC 61000-4-4 (EFT) 40A (5/50ns); IEC 61000-4-5
(Lightning) 25A (8/20μs)
Cable Specifications
For best resolution and ESD performance Shielded CAT6A in a TIA / EIA
568B wiring configuration is recommended.
Cable Type Range Supported Video
CAT5e/CAT6 100m 1080p 60Hz (36 bpp)
70m 1080p 60Hz (48 bpp)
1080p 60Hz 3D
4K 2160p (3840x2160 30Hz)
CAT6A/CAT7 100m 1080p 60Hz (36 bpp)
1080p 60Hz (48 bpp)
1080p 60Hz 3D
4K 2160p (3840x2160 30Hz)
General
Weight
Shipping
Weight
Dimension
(W x H x D)
1.45 lbs. (0.66 kg)
2.45 lbs. (1.12 kg)
12.3'' (with mounting ears) x 0.79'' x 3.85'' (313mm ×
21mm × 98mm)
19
Limited Warranty
The HD-HPC-SP-Tx 100m HDBaseT HDMI and VGA 2x1 Switcher / Extender is warranted
against failures due to defective parts or faulty workmanship for a period of three years after
delivery to the original owner. During this period, FSR will make any necessary repairs or
replace the unit without charge for parts or labor. Shipping charges to the factory or repair
station must be prepaid by the owner, return-shipping charges (via UPS Ground) will be paid
by FSR.
This warranty applies only to the original owner and is not transferable. In addition, it does
not apply to repairs done by other than the FSR factory or Authorized Repair Stations.
This warranty shall be cancelable by FSR at its sole discretion if the unit has been subjected
to physical abuse or has been modified in any way without written authorization from FSR.
FSR’s liability under this warranty is limited to repair or replacement of the defective unit.
FSR will not be responsible for incidental or consequential damages resulting from the use
or misuse of its products. Some states do not allow the exclusion of incidental or
consequential damages, so the above limitations may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state.
Warranty claims should be accompanied by a copy of the original purchase invoice showing
the purchase date (if a Warranty Registration Card was mailed in at the time of purchase,
this is not necessary). Before returning any equipment for repair, please read the important
information on service below.
SERVICE
Before returning any equipment f or repair, please be sure that it is adequately packed and
cushioned against damage in shipment, and that it is insured. We suggest that you save the
original packaging and use it to ship the product for servicing. Also, please enclose a note
giving your name, address, phone number and a description of the problem.
NOTE: all equipment being returned f or repair must have a Return authorization (RMA)
Number. To get a RMA Number, please call the FSR Service Department (1-800-332-FSR1).
Please display your RMA Number prominently on the front of all packages.
CONTACT INFORMATION:
FSR INC.
244 Bergen Blvd.
Woodland Park, NJ 07424
Phone: (973) 785-4347
Order Desk Fax: (973) 785-4207
Web Site: http://www.fsrinc.com
Loading...