User Manual
HD-HAUD-SP-RX
100m HDBaseT HDMI Receiver
244 Bergen Boulevard, Woodland Park, NJ 07424 Tel 973-785-4347
FAX 973-785-3318 Web: www.fsrinc.com
43084 LIT1541
Important Safety Instructions
at plugs.
Contents are subject to change without notice
Warnings
To reduce the risk of fire, electric shock or product damage:
1. Do not expose this device to
rain, moisture, dripping or
splashing and that no objects
filled with liquids, such as vases,
shall be placed on the unit.
2. Do not install or place this unit
in a bookcase, built-in cabinet or
in another confined space.
Ensure the unit is well ventilated.
3. To prevent risk of electric
shock or fire hazard due to
overheating, do not obstruct
the unit’s ventilation openings
with newspapers, tablecloths,
curtains, and similar it ems.
4. Do not install near any heat
sources such as radiators, heat
registers, stoves, or other device
(including amplifiers) that
produce heat.
6. Clean this device only
with dry cloth.
7. Unplug this device
during lightning storms or
when unused for long
periods of time.
8. Protect cables and
cords from being walked
on or pinched particularly
9. Only use
attachments/accessories
specified by FSR.
5. Do not place sources of open
flames, such as lighted c andles,
on the unit.
2
10. Refer all servicing to
qualified service
personnel.
Table of Contents
Important Safety Instructions......................................................................... 2
Overview ......................................................................................................... 4
Features .......................................................................................................... 4
Package Contents .......................................................................................... 4
Typical Application ......................................................................................... 5
HD-HAUD-SP-Rx Front Panel ......................................................................... 6
HD-HAUD-SP-Rx Rear Panel .......................................................................... 7
Hardware Installation ..................................................................................... 8
IR and RS-232 Operation ................................................................................ 9
IR Control ............................................................................................ 9
Scenario 1 .................................................................................... 9
Scenario 2 .................................................................................. 10
RS-232 Control and Firmware Updates ............................................ 11
Scenario 1: Firmware Update .................................................. 11
Scenario 2: RS-232 Control ..................................................... 12
Specifications ............................................................................................... 13
Limited Warranty .......................................................................................... 15
Overview
The HD-HAUD-SP-Rx HDBaseT Extender Receiver is compatible with any of
FSR's 100m HDBaseT Transmitters. It supports HDMI, Ethernet, bi-directional
IR, bi-directional RS-232 and bi-directional PoE. The unit features an audio
de-embedder that extracts stereo audio from the HDMI signal and outputs to a
house sound system. The system can be powered by a single power supply and
its PoE circuitry can power the extender at the far end. The transmitter and
receiver modules are easy to install and space saving. The Extenders are ideal
for home, office, digital entertainment centers, control centers, conference rooms,
schools and corporate training environments.
Features
HD-HAUD-SP-Rx – 100 Meter HDBaseT Slim-Pack Receiver
• HDBaseT In (RJ-45) to HDMI Out
• RS-232 via 3-Pin Captive Screw Terminal (Tx, Rx, GND)
• IR RX & TX via 1/8” mini jacks
• 12VDC Power via screw connector or 2-Pin Captive Screw Terminal
• 2 Ethernet Ports (RJ-45)
• Stereo analog audio output
• Locking power supply included
Package Contents
One 2-pin screw-down terminals
Two 3-pin screw-down terminals
One IR Emitter
One IR Receiver (30kHz ~ 50kHz)
Two Mounting Ears
12VDC 2A power supply
4
Typical Application
POWER SUPPLY
(SOLD SEPARATELY)
ALTERN ATE
POWER INPUT
POWER
SUPPLY
(INCLUDED)
ALTERN ATE
POWER INPUT
HD-H-SP-Tx
HD-HAUD-SP-Rx
-
+
-
+
AUDIO AMP
DC 12V
DC 12V
TV REMOTE
IR RECEIVER
CABLE
-
+
-
+
CATxCABLE
IR EMITTER
CABLE
HDMI INTxRxIR OUTIR IN
TxRx IR OUTIR INLOCAL OUTRL
TV
IR RECEIVER
CABLE
DVDREMOTE
BLUE-RAY
ETHERNET
CONTROLLED
DVD
NORMAL
UPDATE
RJ
TO RS-232
DEVICE
IR EMITTER
CABLE
PC
PC
NOTE: It is only necessary to power one side (Tx or Rx)
The HD-H-SP-Tx Transmitter is shown in the illustrations throughout this manual. Please
note that any of the FSR 100m HD transmitters may be used with the HD-HAUD-SP-Rx
Receiver.
5
HD-HAUD-SP-Rx Front Panel
FSR HD-HAUD-SP-Rx
1 2 3
ON
ID Name Description
1 POWER
2 STATUS
3 HDCP
4 LINK
PWR STATUS HD CP LINKSET
43215
ON: Receiver is powered ON
OFF: Receiver is powered OFF
Intermittent: Normal operating condition
OFF: Fault
ON: HDCP video is being transmitted
Intermittent: No HDCP video is being transmitted
ON: Receiver and Transmitter are linked to each other
OFF/Intermittent: Fault in unit(s) or cabling
SWITCH POSITION
SWITCH 1 SWITCH 2 SWITCH
FUNCTION
3
X 0 0
RS-232 pass-through
enabled
Valens IC update
5
DIP
SWITCH
X 0 1
RS-232 pass-through
MCU update and control
X 1 0
RS-232 pass-through
0 X X NA
1 X X NA
6
disabled
disabled
HD-HAUD-SP-Rx Rear Panel
FSR HD-HAUD-SP-Rx
100m Receiver
HDMI-4k, De-Embedded Audio, IR,
RS-232, DUAL ETHERNET, PoE HDBT
DC12V 12V GND HDBT IN AUD OUT LOCAL OUT RS-232 IR IN IR OUT ETHERNET 1 E THERNET 2
DC 12V
-
-
+
+
Tx Rx IR OUTIR INLOCAL OUTRL
1
2 3 4 5 6
ID Name Description
Connect to a power supply via a power adapter to either
1 POWER
the transmitter or receiver side 12VDC input.
Note: It is only necessary to power one side (Tx or Rx)
2 HDBT IN
Connect to the transmitter via a CAT5e / CAT6 / CAT6A /
CAT7 cable
3 AUDIO Stereo analog output
4 HDMI OUT Connection to the Display
5 RS-232
Used to connect to a computer to update firmware or
connect an RS-232 control device
6 IR IN Connect to an IR receiver cable
7 IR OUT Connect to an IR emitter cable
Ethernet connection for a router, switcher or computer,
ETHERNET
8
1 and 2
etc.
Orange: Link-Activity
Green: Speed 100Mbps
7
8
7
Hardware Installation
Warnings
Before the installation, disconnect the power supply from all the
devices.
Do not connect or disconnect cables from the Transmitter and
Receiver while they are powered ON. To connect or disconnect
cables from the units, power them OFF first.
For best resolution and ESD performance Shielded CAT6A in a TIA
/ EIA 568B wiring configuration is recommended. Please use care
when installing, connecting and disconnecting cables.
1. Connect the source to the HDMI IN on the Transmitter.
2. Connect the IR emitter to the IR OUT and the IR Receiver to the IR IN on
both the Transmitter and Receiver.
3. Connect a Display to the HDMI OUT on the Receiver.
4. Connect the HDBT OUT on the Transmitter to the HDBT IN on the Receiver
via a shielded CAT5e / CAT6 / CAT6A / CAT7 cable.
5. Connect the power supply to either the Transmitter or Receiver.
8
IR and RS-232 Operation
IR Control
The IR pass-through feature on the Transmitter and Receiver allows you to
control the Source from the Display’s location or vice versa.
Scenario 1
The TV can be controlled from the Transmitter’s location with the TV remote.
The IR receiver is connected to the IR IN on the Transmitter and the IR emitter is
connected to the IR OUT on the Receiver.
TV REMOTE
BLUE-RAY
DVD
NORMAL
HDMI INTxRxIR OUTIRIN
UPDATE
RJ
HD-H-SP-Tx
IR RECEIVER
CABLE
DC 12V
-
-
+
+
HDBaseT
HD-HAUD-SP-Rx
-
+
AUDIO AMP
DC 12V
-
+
TxRx I R OUTIRINLOCAL OUTRL
TV
IR EMITTER
CABLE
The HD-H-SP-Tx Transmitter is shown in the illustrations throughout this manual. Please
note that any of the FSR 100m HD transmitters may be used with the HD-HAUD-SP-Rx
Receiver.
9
Scenario 2
The DVD Player can be controlled from the Receiver’s location with the DVD
Player Remote. The IR emitter is connected to the IR OUT on the Transmitter and
the IR receiver is connected to the IR IN on the Receiver.
IR EMITTER
CABLE
BLUE-RAY
DVD
HD-H-SP-Tx
HD-HAUD-SP-Rx
-
+
-
+
AUDIO AMP
DC 12V
DC 12V
NORMAL
-
+
HDBaseT
-
+
HDMI INTxRxIR OUTIR IN
TxRx IR O UTIR INLOCAL O UTRL
TV
IR RECEIVER
CABLE
DVDREMOTE
UPDATE
RJ
The HD-H-SP-Tx Transmitter is shown in the illustrations throughout this manual. Please
note that any of the FSR 100m HD transmitters may be used with the HD-HAUD-SP-Rx
Receiver.
10
RS-232 Control and Firmware Updates
The RS-232 port can be used as pass-through to control a device connected to
the Transmitter from the Receiver or vice versa. In addition, the RS-232 port on
the Transmitter or Receiver can be connected to a computer to update the
firmware.
SWITCH POSITION
SWITCH 1 SWITCH 2 SWITCH
3
X 0 0 RS-232 pass-through enabled
Valens IC update
FUNCTION
FRONT
X 0 1
PANEL DIP
SWITCH
X 1 0
0 X X NA
1 X X NA
Scenario 1: Firmware Update
HD-HAUD-SP-Rx
DC 12V
-
-
+
+
RS-232 pass-through
disabled
MCU update and control
RS-232 pass-through
disabled
TxRx IR OUTIR INLOCAL OUTRL
PC
11
Scenario 2: RS-232 Control
Maximum Baud rate is 115.2 Kbps.
TO RS-232
DEVICE
HD-H-SP -Tx
HD-HAUD-SP-Rx
DC 12V
-
-
+
+
CATx CABLE
DC 12V
-
-
+
+
TxRx IR OUTIRINLOCAL OUTRL
TO RS-232
DEVICE
NORMAL
HDMI INTx RxIR OUTIRIN
UPDATE
The HD-H-SP-Tx Transmitter is shown in the illustrations throughout this manual. Please
note that any of the FSR 100m HD transmitters may be used with the HD-HAUD-SP-Rx
Receiver.
12
Specifications
HD-HAUD-SP-Rx
Input 1 HDBT
Input Signal Type HDBT
Technical
Input Resolution
Support
Input Video Level 0.5-1.2 Vp-p
Output 1 HDMI
Output Signal Type HDMI
Video Impedance 100Ω
Maximum Pixel Clock 297 MHz
Operating
Temperature
Storage Temperature
Power Supply DC 12V 2A with locking connector
ESD Protection Human-body Model:
Surge Protection
4k 2160p (3840x2160) / 1080p / 1080i / 720p /
576p / 480p / 576i / 480i
32°F to 95°F (0°C to 35°C)
10% to 90%, non-condensing
-4°F to 140°F (-20°C to 70°C)
10% to 90%, non-condensing
±8kV (Air-gap discharge)
±4kV (Contact discharge)
IEC 61000-4-4 (EFT) 40A (5/50ns); IEC 61000-4-5
(Lightning) 25A (8/20μs)
13
Cable Specifications
For best resolution and ESD performance Shielded CAT6A in a TIA / EIA
568B wiring configuration is recommended.
Cable Type Range Supported Video
100m 1080p 60 Hz 36 bpp
CAT5e/CAT6
70m
CAT6A/CAT7 100m
Shipping
Weight
Dimension
(L x D x H)
2.25 lbs (1.03 kg).
9.93" x 3.85" x .71" (252mm x 98mm x 18mm)
(with mounting ears installed)
1080p 60 Hz 48 bpp
1080p 60 Hz 3D
4K 2160p (3840 x 2160 30Hz)
1080p 60 Hz 36 bpp
1080p 60 Hz 48 bpp
1080p 60 Hz 3D
4K 2160p (3840 x 2160 30Hz)
General
14
Limited Warranty
The HD-HAUD-SP HDBaseT HDMI Extender Set is warranted against failures due to
defective parts or f aulty workmanship for a period of three years after delivery to the original
owner. During this period, FSR will make any nec essary repairs or replace the unit without
charge f or parts or labor. Shipping charges to the factory or repair station must be prepaid
by the owner, return-shipping charges (via UPS Ground) will be paid by FSR.
This warranty applies only to the original owner and is not transferable. In addition, it does
not apply to repairs done by other than the FSR factory or Authorized Repair Stations.
This warranty shall be cancelable by FSR at its sole discretion if the unit has been subjected
to physical abuse or has been modified in any way without written authorization from FSR.
FSR’s liability under this warranty is limited to repair or replacement of the defective unit.
FSR will not be responsible for incidental or consequential damages resulting from the use
or misuse of its products. Some states do not allow the exclusion of incidental or
consequential damages, so the above limitations may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state.
Warranty claims should be accompanied by a copy of the original purchase invoice showing
the purchase date (if a Warranty Registration Card was mailed in at the time of purchase,
this is not necessary). Before returning any equipment for repair, please read the important
information on service below.
SERVICE
Before returning any equipment f or repair, please be sure that it is adequately packed and
cushioned against damage in shipment, and that it is insured. We suggest that you save the
original packaging and use it to s hip the product for servicing. Also, please enclose a note
giving your name, address, phone number and a description of the problem.
NOTE: all equipment being returned for repair must have a Return authorization (RMA)
Number. To get a RMA Number, please call the FSR Service Department
(1-800-332-FSR1).
Please display your RMA Number prominently on the front of all packages.
CONTACT INFORMATION:
FSR INC.
244 Bergen Blvd.
Woodland Park, NJ 07424
Phone: (973) 785-4347
Order Desk Fax: (973) 785-4207
Web Site: http://www.fsrinc.com
15
Loading...