FSR FLH20-1-BX User Manual

COVER INSTALLATION

INSTALL BOX-ATTACHED CHAIN TO COVER, AND REPLACE COVER
BACK INTO NEWLY-INSTALLED RIM, LATCHING THE SMALL DOORS
IN PLACE (REVERSE ACTIONS OF DETAILS 1 THRU 3 PREVIOUSLY
DONE). CHAIN FROM BOX CAN BE REMOVED AND INSTALLED TO
ALTERNATE LOCATION, IF DESIRED. INSTALL FINISHED FLOOR
SURFACE/COVERING.

FSR

244 Bergen Boulevard, West Paterson, NJ 07424, Phone: [phone] - Fax: [phone]

FLH20-1-BX/FLH20-1S-C Installation Guide

BRACKET FOR STORING

SMALL DOOR WHEN

REMOVED FROM COVER

COVER

#8-32 PAN HEAD SCREW

CHAIN FROM BOX

STUD FOR ALTERNATE
LOCATION OF CHAIN

BOX INSTALLATION - STEP 1

REMOVE AND RETAIN TEMPORARY COVER AND SCREWS.
LOCATE AND POSITION BOX IN ACCORDANCE WITH
FLOOR PLANS. TOP EDGE OF BOX MUST
CONCRETE POUR. LEVEL AND ANCHOR BOX AS REQUIRED.
USE SCREWS, NAILS, OR WIRE TO PREVENT BOX FROM
FLOATING DURING POUR. ROUTE CONDUITS TO BOX AS
REQUIRED. PLACE THIS INSTALLATION GUIDE BACK INTO
BOX, ALONG WITH ALL SUPPLIED ITEMS, AND REINSTALL
TEMPORARY COVER.

TEMPORARY COVER

BE FLUSH WITH

(4) #8-32 FLAT HEAD SCREW

TOP EDGE TO
BE FLUSH WITH
CONCRETE

BOX INSTALLATION - STEP 2

SCREED TO TOP OF BOX SURFACE. HAND TROWELING
RECOMMENDED NEAR BOX EDGES. BOX HAS NO
HEIGHT ADJUSTMENT AFTER CONCRETE POUR.

CONCRETE SURFACE

INSTALL FINISHED FLOOR

SURFACE/COVERING

INSTALL FINISHED FLOOR
SURFACE/COVERING

FSR Inc.

244 Bergen Boulevard, West Paterson, NJ 07424
Phone: [phone] - Fax: [phone]
Web: www.fsrinc.com - E-mail: [e-mail]

CENTER DIVIDER CONFIGURATION

SET ASIDE TEMPORARY COVER AND SCREWS FOR POSSIBLE RE-INSTALLATION.
REMOVE AND RETAIN GANG MOUNTING BRACKETS AND SCREWS TO CONFIGURE
CENTER DIVIDERS.

(10) #8-32 PAN HEAD SCREW

GANG MOUNTING BRACKET

43133 LIT1234

C-1058

REMOVABLE LARGE CENTER DIVIDER

REMOVABLE SMALL
CENTER DIVIDER

GANG MOUNTING BRACKET

REMOVABLE SMALL
CENTER DIVIDER

REMOVABLE LARGE CENTER DIVIDER

GANG DIVIDER ASSEMBLY

CUTAWAY FOR

CLARITY ONLY

DIVIDER HOLDER:

INSTALL WITH #8-32

FLAT HEAD SCREW

TO GANG MOUNTING

BRACKET

COVER PLATE:

INSTALL WITH #6-32

PAN HEAD SCREW TO

GANG MOUNTING

BRACKET

INSTALLING ELECTRONIC COMPONENTS

PULL WIRES AND CABLES TO BOX AS NECCESSARY (REMOVAL OF
GANG MOUNTING BRACKETS MAY BE REQU IRED). TERMINATE
WIRES AND CABLES TO ELECTRONIC COMPONENTS, AND INSTALL
ELECTRONIC COMPONENTS ONTO GANG MOUNTING BRACKETS.
PLACE THIS INSTALLATION GUIDE BACK IN BOX AND REINSTALL
TEMPORARY COVER IF FINISHED COVER IS TO BE INSTALLED AT
A LATER DATE.

IF INSTALLING "JUNCTION BOX/ABANDONMENT" COVER, USE

THAT COVER'S INSTALLATION GUIDE, AND IGNORE THE REMAINDER

OF THESE INSTALLATION INSTRUCTIONS.

MOUNTING

BRACKET

NOTE

COVER ASSEMBLY

GANG

INSTALLED
ELECTRONIC
COMPONENT

OPTIONAL

DIVIDER

(2) #8-32 PAN HEAD SCREW

GANG MOUNTING BRACKET CONFIGURATION

PER CUSTOMER SPECIFICATIONS , C O NF IGURE GANG MOUNTING BRACKETS AS SHOWN BELOW AND
REASSEMBLE INTO BOX (DECORA WALL PLATES SHOWN AS REFERENCE AND NOT INCLUDED).

GANG MOUNTING BRACKET

COVER

PLATE

87.5

cu. in.

(2) DIVIDER HOLDER

1-GANG/2-GANG CONFIGURATION

(2-GANG/1-GANG ALSO POSSIBLE)

OPTIONAL
DIVIDER

94

cu. in.

2-GANG/2-GANG CONFIGURATION

OPTIONAL

DIVIDER

87.5

cu. in.

GANG MOUNTING
BRACKET

94

cu. in.

DIVIDER
HOLDER

COVER RIM INSTALLATION

REMOVE AND DISCARD TEMPORARY COVER AND SCREWS.
REMOVE COVER ASSEMBLY FROM RIM (SEE DETAILS 1 THRU 3),
SET REMOVED COVER (WITH SMALL DOORS) ASIDE. APPLY A
CONTINUOUS 1/4" BEAD OF RTV SILICONE TO THE INSIDE CORNER
OF ALL 4 SIDES OF THE CONCRETE-STOP FLANGE ON THE BOX
(SEE RTV SILICONE PLACEMENT DETAIL). QUICKLY INSTALL RIM
ONTO BOX WITH PROVIDED #8-32 x 1/4" FLAT HEAD PHILLIPS
SCREWS.

LATCH OPERATION

DETAIL 1

LIFT LATCH HANDLE 90°

ROTATING LATCH HANDLE 45° CLOCKWISE

ALLOWS COVER TO BE REMOVED FROM RIM

DETAIL 2

RIM

DETAIL 3

ROTATING LATCH HANDLE 90° CLOCKWISE

ALLOWS SMALL DOOR TO BE REMOVED

FROM COVER

OPTIONAL

DIVIDER

117.5
cu. in.

DIVIDER

HOLDER

GANG MOUNTING

3-GANG/1-GANG CONFIGURATION

(1-GANG/3-GANG ALSO POSSIBLE)

BRACKET

64

cu. in.

183.3
cu. in.

(2) DIVIDER HOLDER
(NO DIVIDERS USED!)

4-GANG CONFIGURATIO N

GANG MOUNTING
BRACKET

CONCRETE FLOOR

CONTINUOUS
1/4" BEAD OF
RTV SILICONE

RTV SILICONE PLACEMENT DETAIL

(10) #8-32 FLAT HEAD SCREW

RIM

APPLY A CONTINUOUS 1/4" BEAD
OF RTV SILICONE TO ALL 4 SIDES