FSR FL-700-SLP-C Datasheet
FL-700
PASS THRU FLOOR BOX
FL-700
Metal Products Group
Scrub water approved for
carpet, tile, and wood floors!
DESCRIPTION
DESCRIPTION
The FL-700 floor box is designed for conference
rooms, auditoriums, classrooms, etc. where it may be
necessary to pass cables thru the box without interfering with the various connectors. This simplifies installation of wiring when a group of boxes must be connected in series. The pass thru route is front to back.
The FL-700 is used on carpeted floors over concrete.
This floor box provides a practical and safe solution for
easy access to cables and connector plates. The liftoff section of the cover allows full access to internal
cables and connector plates while a smaller, hinged
trapdoor flips back to create a cable exit. All cables
can be stored within the box when they are not in use,
allowing unencumbered travel in the area.
The sturdy 11 gauge steel cover is installed flush with
the floor. The low profile edging is 1/4” high and is available in brass or aluminum. When the box is not in use,
only the elegant, hand mitered carpet edge is visible.
Inside the FL-700, one angled bracket is provided for
cable connections with ample clearance for cable
connectors.
The angled brackets provide two single and one triple
gang opening, which are all isolated for maximum safety.
The FL-700 is extremely sturdy (steel and welded construction) and has been designed to fit the needs of
power, audio, video, telecommunications, and data
applications.
Note: When this box is used on grade, it should be
encased in concrete to prevent contact with the grade.
To ensure compliance, we recommend using the FSR
Pour Pan Accessory.
SPECIFICATIONS
SPECIFICATIONS
Size: Box: 8” x 14” x 5 1/4”
Cover: 8” x 14”
Material - 1/8” steel
Edging: Height: 1/4” in beveled or square profiles
Material: Brass or Aluminum
Weight: Box: 18 lbs.
Cover: 5 1/2 lbs.
Knockouts: Six, either 1/2” or 3/4”
Eight, either 1” or 1-1/4”
ORDERING INFORMATION
ORDERING INFORMATION
FL-700 - Requires Cover and Back Box
Covers - UL Scrub Water Rated for Tile and Carpet Installations
FL-700-BLP-C 1/4” Beveled Brass Carpet Flange (Lift off door)
FL-700-SLP-C 1/4” Beveled Aluminum Carpet Flange (Lift off door)
FL-700-SSQ-C 1/4” Square Aluminum Flange (Lift off door)
Covers - Not Scrub Water Rated (Non UL)
FL-700-BLK-C (No Flange) With Hinged Door in Black Sandtex
Back boxes - UL Listed - Includes Steel Construction Cover
FL-700 Bottom FL-700 Back Box - 5 1/4” Deep
FSR Inc.
244 Bergen Boulevard, Woodland Park, NJ 07424
Phone: 973.785.4347 · Fax: 973.785.4207
Web: www.fsrinc.com · E-mail: sales@fsrinc.com
Order Desk: 1-800-332-FSR1 LIT1064G
FRO
NT O
F BO
X
BOTTOM, AND BACK
~
PLATE
A/C
DIVIDER
LARGE CONDUIT KNOCKOUT
TYPICAL, 1 PER SIDE
TRIM
CARPET
SHORT
LEVELING FEET
FINISHED FLOOR
MUST BE FLUSH WITH
TOP OF FLOOR BOX COVER
CARPET PILE
FLOOR
CONCRETE
POURED
.60”
1/4"
.42”
CONDUIT KNOCKOUTS,
TYPICAL FOR FRONT,
O
F CO
VER
TO
P SURFACE
(2) 1/2" & 3/4"
OF CROSS SECTION
DIRECTION OF VIEW
BOTTOM, AND BACK
TYP. FOR 2 SIDES
1" & 1-1/4"
CONDUIT KNOCKOUT,
TYPICAL FOR FRONT,
CONDUIT KNOCKOUTS,
(2) 1" & 1-1/4"
OPENING
OPENING
1 GANG,
1 GANG,
3 GANG
5.3”
2.6”
14.0”
2.6”
8.0
FL-700 INTERNAL BRACKET ARRANGEMENT
DIVIDER
DIVIDER
TEMPORARY
CABLE
ACCESS
DOOR
COVER
SPACER
ANGLES
FL-700
FLOOR
BOX
MADE IN
THE USA
FL-700 INTERNAL BRACKET ARRANGEMENT
FL-700
Top View with Door Location Top View with
Bracket Arrangement
Side View Showing Internal Bracket Placement
1/4” Carpet Edging
The Internal Mounting Brackets Accommodate
2 - Single Gang Plates
1 - Three Gang Plate
1
Depth of box in 5
Installation Cross Section
⁄4”
Specifications are subject to change without notice.
Cable pass through
244 Bergen Boulevard, Woodland Park, NJ 07424
Phone: 973.785.4347 · Fax: 973.785.4207
Web: www.fsrinc.com · E-mail: sales@fsrinc.com
Loading...