FSR FL-540P User Manual
GANG DIVIDER ASSEMBLY
DIVIDER HOLDER MUST
TO DIVIDERS, IN ORDER TO PROPERLY ASSEMBLE BOX INTERIOR.
BE ORIENTED AS SHOWN WHEN ATTACHING
FSR
FL-540P INSTALLATION INSTRUC TIONS
244 Bergen Boulevard, Woodland Park, NJ 07424, Phone: 973.785.4347 - Fax: 973.785.4207
4" BOX DIVIDER 5"-6" BOX DIVIDER 7"-12" BOX DIVIDER
DIVIDER
DIVIDER HOLDER
(2) #8-32 x .25 LG
PAN HEAD
SCREW
* DIVIDER ASSEMBLY FOR 5" & 7" BOXES
POSITION DIVIDER ASSEMBLY IN BOX BEFORE INSTALLING
GANG PLATE ASSEMBLY. SECURE DIVIDER ASSEMBLY TO
GANG PLATE ASSEMBLY WITH SCREWS AS NOTED.
GANG
MOUNTING
PLATE
DIVIDER
(2) #8-32 x .25 LG
PAN HEAD
SCREW
DIVIDER HOLDER
GANG PLATE ASSEMBLY
(2) #8-32 x .25 LG
FLAT HEAD
SCREW
DIVIDER
(2) #8-32 x .25 LG
PAN HEAD
SCREW
DIVIDER HOLDER
(4) #8-32 x .375 LG
SELF TAPPING
PAN HEAD
SCREW
BOX INSTALLATION
LOCATE AND POSITION BOX IN ACCORDANCE WITH FLOOR PLANS. HOLE TO BE
CUT IN FLOOR - 12-1/4" x 10-1/4". DROP FLOOR BOX THRU HOLE AND SECURE
WITH #8 HARDWARE (BY INST ALLE R) - LIP ON BOX CAN ACCOMODATE #8 COUNTERÂSUNK SCREWS. REMOVE AND RETAIN TEMPORARY COVER AND SCREWS. ROUTE
CONDUITS TO BOX AS REQUIRED. PLACE THIS INSTALLATION GUIDE BACK INTO
BOX, ALONG WITH ALL SUPPLIED ITEMS, AND REINSTALL TEMPORARY COVER.
12-1/4" x 10-1/4" HOLE IN FLOOR
#8 FLAT HEAD
HARDWARE
(BY INSTALLER)
DIVIDER ASSEMBLY
INSTALLING ELECTRONIC COMPONENTS
PULL WIRES AND CABLES TO BOX AS NECCESSARY (REMOVAL OF
GANG MOUNTING BRACKETS MAY BE REQUIRED). TERMINATE
WIRES AND CABLES TO ELECTRONIC COMPONENTS, AND INSTALL
ELECTRONIC COMPONENTS ONTO GANG MOUNTING BRACKETS.
REINSTALL TEMPORARY COVER IF FINISHED COVER IS TO BE
INSTALLED AT A LATER DATE.
GANG
MOUNTING
BRACKET
(8) #6-32 FLAT HEAD SCREW
TEMPORARY
COVER
INSTALLED
ELECTRONIC
COMPONENT
FLOOR NOT SHOWN FOR CLARITY
OF CONDUIT INSTALLATION
43201 LIT1333
TYPICAL INSTALLATION
CARPET OVER CONCRETE (COVER WITH EDGING)
TEMPORARY COVER
CARPET
EDGING
FINISH COVER
GANG MOUNTING BRACKET CONFIGURATION
PER CUSTOMER SPECIFICATIONS, CONFIGURE GANG MOUNTING BRACKETS AS SHOWN BELOW AND
REASSEMBLE INTO BOX (DECORA WALL PLATES SHOWN AS REFERENCE AND NOT INCLUDED).
COVER PLATE
DIVIDER
HOLDER
FLOORING
FLOOR BOX
MATERIAL
FLOORING
MATERIAL
VINYL FLOORING OVER CONCRETE (COVER WITHOUT EDGING)
TEMPORARY COVER
FLOORING
MATERIAL
VINYL FLOORING
FLOOR BOX
FLOORING
MATERIAL
CENTER DIVIDER CONFIGURATION (NOT APPLICABLE ON 4" BOX)
SET ASIDE TEMPORARY COVER AND SCREWS FOR POSSIBLE RE-INSTALLATION.
REMOVE AND RETAIN GANG MOUNTING BRACKETS AND SCREWS TO CONFIGURE
CENTER DIVIDERS.
FLOOR BOX
FINISH COVER
FLOOR BOX
(2) DIVIDER
HOLDER
GANG
MOUNTING
BRACKET
OPTIONAL DIVIDER
OPTIONAL DIVIDER
1-GANG/2-GANG CONFIGURATION 1-GANG/3-GANG CONFIGURATION
GANG MOUNTING BRACKET
DIVIDER
HOLDER
OPTIONAL
DIVIDER
GANG MOUNTING BRACKET
OPTIONAL DIVIDER
2-GANG/2-GANG CONFIGURATION 3-GANG/1-GANG CONFIGURATION
GANG
MOUNTING
BRACKET
DIVIDER
HOLDER
POSSIBLE GANG DIVIDER LOCATION
REMOVABLE LARGE CENTER DIVIDER
REMOVABLE SMALL
CENTER DIVIDER
REMOVABLE SMALL
CENTER DIVIDER
REMOVABLE LARGE CENTER DIVIDER
GANG MOUNTING BRACKET
(2) DIVIDER HOLDER
(NO DIVIDERS USED)
4-GANG CONFIGURATION
BOTH GANG MOUNTING BRACKETS ARE IDENTICAL, AS IS THEIR CONFIGURATION CAPABILITY
Loading...