FSR DV-WPHXT-1C-WHT User Manual

USER MANUAL

DV-WPHXT-1C-WHT/ DV-WPHXT-1ctx

DIGITAL / ANALOG AUTO SWITCHING CAT-x TRANSMITTER

2-GANG DECORA WALLPLATE

244 Bergen Boulevard, Woodland Park, NJ 07424  Tel [phone]  FAX [phone]

Web: www.fsrinc.com

LIT1421E

2

Proprietary Information

All information in this manual is proprietary to and the property of FSR Inc. This
publication is protected by the Federal Copyright Law, with all rights reserved.
No part of this document may be reproduced, transcribed, or transmitted, in
any form or by any means, without prior explicit written permission from FSR
Inc.

Unpacking

DV-WPHXT-1C-WHT package includes the following items:

DV-WPHXT-1CTx Switching CAT-x transmitter Dual Decora Wall plate
DV-HXT-1CT Receiver Unit
5V Power Adapter
DVI to HDMI Cable
User manual

DV-WPHXT-1ctx can be ordered separately

Cautions:

1. FSR logo is a trademark of FSR Inc.

2. HDMI is a trademark of HDMI licensing, LLC.

3. Specification may be changed without any notice in order to
improve the function of the product.

4. The design and specification of the product may be change

without any prior notice.

3

4

Table of Contents

Proprietary Information ............................................................................................ 3

Description, General Specifications ......................................................................... 6

Environmental and Reliability Specifications ........................................................... 7

Main Features ......................................................................................................... 9

Video Connection .................................................................................................. 11

UTP Cat Cable terminations and pinouts .............................................................. 14

RS-232 Command ................................................................................................. 15

Troubleshooting ..................................................................................................... 16

Mechanical Specifications ..................................................................................... 17

Control and Connector Locations .......................................................................... 18

Technical Specification .......................................................................................... 19

Limited Warranty ................................................................................................... 21

5

Description, General Specifications

 High quality transmission of VGA or DVI / HDMI signals over long distances

using a single Cat-x cable

 DV-WPHXT-1ctx is designed with energy saving features.
 Connects with FSR DV-MFSW-94 Presentation Matrix Router inputs to expand

VGA or Digital capability or use with our DV-HXT-1 Receiver Unit.

 DV-WPHXT-1ctx uses inexpensive and easily terminated Cat5e /6a cable

providing easy installation.

 Sends high quality VGA / DVI / HDMI, STEREO AUDIO signals over long

distances using a single Cat cable

ITEM DESCRIPTION
Model Name DV-WPHXT-1ctx

Input Signal VGA / DVI / HDMI, Stereo Audio
Output Signal TMDS

Cat6a: 164ft (50m) at 1920x1080p

Resolution

Receptacle

HDCP / EDID
Support

Power
Consumption

Power supply *

Dimension 4.09” H x 3.51” W x 1.81” D (103.9 H x 90.5 W x 31 D mm)
Weight 0.9 lbs. (0.4Kg)

Cat6a: 164ft (50m) at 1920x1200

DC Power Jack (3.5mm Phoenix 2P)
VGA HD-15 Female
HDMI Female
RS-232C port (3.5mm Phoenix 3P)
Stereo Audio Jack
RJ45

Compliant / EPROM

DC 5V@ 10 W Max
DC 5V@ 2A

* NOTE: The length of cable between the wall plate and the power supply can be extended
up to 50' by using 16 AWG wire. Longer distances, from a minimum of 51' to maximum of
150' can be achieved using the FSR 17420 power supply in conjunction with the 16 AWG
wire. The installer is cautioned to ensure correct polarity before applying po wer to the wall
plate. Incorrect polarity will damage the unit and void the warranty.

6

Environmental and Reliability Specifications

Recommended environmental conditions for the operation are temperature
range of 50°– 104°F (10°C– 40°C), non-condensing humidity levels of 10%–
80%, and altitude ceiling of 9,840 feet (3,000 meters).

Environmental limits for transportation are temperature range of -13°– 122°F
(-25°C– 60°C), non-condensing humidity levels of 5%– 95%, and altitude
ceiling of 49,200 feet (15,000 meters)

Environmental limits for storage are established at temperature range of

-13°– 122°F (-20°C– 45°C), non-condensing humidity levels of 5%– 95%, and
altitude ceiling of 9,840 feet (3,000 meters)

The DV-WPHXT-1ctx is expected to function for more than 50,000 hours of
use at a 90% confidence level. The device is tested according to the identical
standards for testing LCD monitors.

7

8

Main Features

High Quality Picture - No Signal Loss and Auto-adjusting

DV-WPHXT-1ctx is built to deliver the highest quality picture preserving the
native resolutions of the video source

Signal Amplification

Cutting edge design transmits high quality video signals and compensates for
signal loss over long distances.

Compact and Practical Design

DV-WPHXT-1ctx will make installation quick and simple. The compact unit fits in a
standard 2-gang box.

Auto Detect Input Signals

The unit auto detects and switches to live input signals which are VGA or DVI /
HDMI. Sources can be manually selected via local push-button or remotely via
RS232 commands.

NOTE: When there are active signals on both inputs, the unit will
switch to the last selected input.

HDCP (High-bandwidth Digital Content Protection)

The DV-WPHXT-1ctx is fully compliant with HDCP.

NOTE: All digital sources must be HDCP compliant. The unit will not

display, if the products are not HDCP compliant.

Compliance to DDWG Ver 1.0

DV-WPHXT-1ctx fully supports the DDWG Ver.1.0

Built in EDID Read and save functions

Built in Extended Display Identification Data (EDID) read function, with
Electrically Erase Programmable Read-Only Memory (EEPROM), to save
display EDID data while supporting any monitor with common resolutions.
The unit also supports user set up of non-Video Electronics Standards
Association (VESA) resolutions, including projectors with unique resolutions.

9

EDID [Extended Display Identification Data]
EDID is defined by a standard published by the Video Electronics Standards

Association (VESA). The EDID includes manufacturer name, product type,
phosphor or filter type, timings supported by the display, display size, luminance
data and (for digital displays only) pixel mapping data.

10

Video Connection

Step 1: Connect the Sources (VGA / DVI / HDMI / AUDIO) and CAT cable to
the DV-WPHXT-1ctx, and connect Cat cable from DV-WPHXT-1ctx
to appropriate CAT Receiver or DV-MFSW-94 Presentation Matrix
Router.

Step 2: Connect power adapter to the DV-WPHXT-1ctx *

Step 3: Power ON the appropriate Receiver or DV-MFSW-94 Presentation

Matrix Router including sources and display. (DV-WPHXT-1ctx will
detect sources automatically. If both inputs are live, the unit will
auto-select the digital input source. The input can be selected
manually using either the Input Select push-button or via RS-232
control.

Step 4: Using the EDID table below, select the correct EDID Data on the
EDID Rotary Switch and press EDID Learn button to store the
setting. If the EDID data is not found on the table follow the steps
under “EDID DATA Saving Setup” on the following page

NOTES: 1920x1080P is the factory default set up.
Whenever you use HDMI embedded audio

the EDID Rotary Switch should be set to
to “D” which is 1080p@60hz, 2ch audio

For DVI / HDMI audio switching thru RS-232 command
see the “RS-232 Control” Section.

* NOTE: The length of cable between the wall plate and the power supply can be
extended up to 50' by using 16 AWG wire. Longer distances, from a minimum
of 51' to maximum of 150' can be achieved using the 17420 power supply in
conjunction with the 16 AWG wire. The installer is cautioned to ensure correct
polarity before applying power to the wall plate. Incorrect polarity will damage the
unit and void the warranty.

11

MODE NUMBER EDID DATA

0 EXTERNAL(EDID data save mode)

1 800x600

2 1024x768

3 1280x768

4 1280x1024

5 1360x768

6 1366x768

7 1400x1050

8 1600x900

9 1600x1200

A 1680x1050

B 1920x1200

C 1280x720P/1920x1080i 2ch audio

D 1920x1080P 2ch Audio (Default set)

E 1920x1080P 5ch audio

F RESERVED

12

EDID data saving setup

Follow this setup procedure to auto acquire the EDID data when the rotary
switch setup under Step 4 of the preceding “Video Connection” setup is
unsuccessful or the correct EDID data for the display can not be found on the
Internal (Pre-saved) EDID table.

Step 1: Connect VGA or DVI / HDMI source input port on DV-WPHXT-1ctx

directly to the display.
Step 2: Power up the display and DV-WPHXT-1ctx.
Step 3: Select the appropriate source input port; VGA or DVI / HDMI
Step 4: Set the number to “0” on the rotary switch.
Step 5: Press the EDID Learn Button for 2~4 seconds.
Step 6: Green Status LED will be illuminated (steady) for about 2-3 second if

the EDID was saved correctly.

Troubleshooting:

 If the EDID was not saved correctly, the Green Status LED will

blink In this case, go back to Step 4

 The EDID learn Button must be pressed after selecting one

of EDID data values using the rotary switch

 Confirm that the EDID value was saved to the correct source

port such as VGA or DVI / HDMI (see step 3)

When changing EDID mode, unplug the power cable at the Transmitter.
Whenever you use HDMI embedded audio, you should set the EDID to “D”

which is 1080p@60hz, 2ch audio

13

UTP Cat Cable terminations and pinouts

Looking into the connector
at the rear of the wall plate

TIA/EIA-568B Signal

Pin

1 Orange/ White TMDS Data2+ +5V

2 Orange TMDS Data2- HPD
3 Green/ White TMDS Data1+ Ground
4 Blue TMDS Data0+ CEC
5 Blue/ White TMDS Data0- Ground
6 Green TMDS Data1- DDC data
7 Brown/ White TMDS Clock+ Ground
8 Brown TMDS Clock- DDC Clk

Wire color Digital RGB DDC

 We do not recommend punch down terminations.
 We do not recommend using STP (shielded twisted pair)) cable. For high

resolution (above 1080p or WUXGA), using CAT6a 550MHz unshielded solid
core by Liberty Wire & Cable is recommended.

14

RS-232 Command

Baud rate: 19200 bps
Data bits: 8 bit
Stop bits : 1 bit,
Parity: No
Flow control: None .

Commands:

CON DVI <CR> Switch to DVI /HDMI
CON VGA <CR> Switch to VGA
CON ATS <CR> Auto switch mode ON
CON ATE <CR> Auto switch mode OFF
AUD DIG <CR> DVI / HDMI source audio select
AUD 3.5 <CR> 3.5 stereo audio select

15

Troubleshooting

The DV-WPHXT-1ctx Cat Transmitter is designed for years of trouble free service.
Please reference the troubleshooting chart below if experiencing issues with the
device.

Problem Solution

No picture (or
signal)

Poor picture or
noise

1. Ensure the status LED is illuminated.

2. Check DV-WPHXT-1ctx Transmitter is properly
connected with sources.

3. Check that Cat cable connecter is properly
terminated TIA/EIA-568B (See table).

4. Set EDID correctly for VGA or DVI / HDMI
(Refer to “Video Connection”)

5. Power cycle source device after connecting the
Cat cable.

1. Restart the source device or DV-MFSW-94 if
used.

2. Unplug the DC power adapter, disconnect DVI /
HDMI or VGA cable, reconnect the cables and
replug the power adapter.

3. Check proper grounding of devices.

4. Confirm that the selected EDID is the same as

the displays’ native resolution.

(Refer to Video Connection and Operation

No Sound 1. Make sure that the proper source is selected.

2. Set the DVI / HDMI source via RS232 command

(Refer to RS-232 Command section)

16

Mechanical Specifications

.93 1.81

.14

.77

1.81 REF.

1.47 REF.

3.81

PC INPUT

HDMI INPUT

DV-WPHXT-1CTx

INPUT

SELECT

PC

AUDIO IN

DVI/

HDMI

.41

3.28

4.09

.69

2.72

FSR

.69

.14

3.51

.41

1.19

.12

Made In Korea

CAT X OUT

+5V GND TxD RxD GND

DVI/PC INPUT EDID TABLE

0.

EXTERNAL MONITOR EDID

1.

800x600

2.

1024x768

3.

1280x768

4.

1280x1024

5.

1360x768

6.

DVI: 1336x766
PC: NOT SUPPORTED

7.

1400x1050

8.

DVI: 1600x900
PC: NOT SUPPORTED

9.

1600x1200

A.

DVI: 1680x1050
PC: NOT SUPPORTED

B.

1920x1200

C.

DVI: HD1080i_2CH
PC: 1080p

D.

DVI: HD1080p_2CH
PC: 1080p

E.

DVI: HD1080p_Multi
PC: 1080p

F.

RESERVED

17

Control and Connector Locations

/

EDID SELECT PUSHBUTTON

RJ45 OUTPUT JACK
TO DV-HXT-I RECEIVER
OR DJ-MFSW-94
SWITCHER / SCALER

EDID INDICATOR LED

HD-15 FOR PC (VGA)
VIDEO INPUT

*

VIDEO INPUT
SELECT
PUSHBUTTON

*

5-PIN SCREW DOWN
TERMINAL FOR POWER
RS-232 COMM PORT

HDMI / DVI INPUT

**

LOCATED UNDER COVER PLATE

*

WITH HDMI TO DVI CABLE (INCLUDED)

**

PC INPUT

HDMI INPUT

DV-WPHXT-1CTx

INPUT

SELECT

PC

DVI /
HDMI

AUDIO IN

FSR

EDID DATA SELECT
ROTARY SWITCH

INPUT STATUS
INDICATOR
LED'S

3.5 STEREO
AUDIO INPUT
JACK

*

Made In Korea

EDID TABLE

CAT X OUT

+5V GND TxD RxD GND

DVI/PC INPUT EDID TABLE

0.

EXTERNAL MONITOR EDID

1.

800x600

2.

1024x768

3.

1280x768

4.

1280x1024

5.

1360x768

6.

DVI: 1336x766
PC: NOT SUPPORTED

7.

1400x1050

8.

DVI: 1600x900
PC: NOT SUPPORTED

9.

1600x1200

A.

DVI: 1680x1050
PC: NOT SUPPORTED
1920x1200

B.

DVI: HD1080i_2CH

C.

PC: 1080p

D.

DVI: HD1080p_2CH
PC: 1080p

E.

DVI: HD1080p_Multi
PC: 1080p

F.

RESERVED

PC INPUT: PC (VGA) Input HD-15 connector
DVI INPUT: HDMI Female (with included DVI / HDMI

cable)
HDMI INPUT: HDMI Female
AUDIO IN: 3.5mm Stereo Audio Input connector
RJ-45 CAT: TMDS signal output
DC-5V: Power input (5-pin screw down terminal)
TxD RxD GND: Sources select through RS232 command/

Firmware updates (5-pin screw down terminal)
INPUT SELECT SWITCH : VGA or DVI / HDMI input selection push button
EDID LED: Display the status of EDID (Saving and

Changing)
EDID LEARN BUTTON: EDID data save push button (Internal and

External)
EDID ROTARY SWITCH: Internal (Pre-saved) EDID select switch
PC LED: Displays the status of VGA signal
DVI / HDMI LED: Displays the status of DVI / HDMI signal

18

Technical Specification

Data transmission speed: 2.25 Gbps (Single Link)
Digital Video Bandwidth: 25~225 MHz
Resolution: Up to WUXGA (1920x1200) @

60Hz 1080p)
DVI Version 1.1 Compliance with

Stereo Audio
Input/Output signal standard: VGA, DVI / HDMI (with included

DVI / HDMI cable), Stereo Audio
Maximum length: 1920x1200@60Hz,1080p with

Cat 6a UTP 550MHz: 50m (164ft)
Transmitter connectors: VGA, HDMI, RJ-45, 3.5mm

Stereo Audio jack, 5 pin pluggable
screw connector
(Power/RS232/TX RX/Ground)

Power consumption: 3 Watts (Max)
Power supply: DC 5V@2A

We do not recommend punch down terminations or STP (Shielded Twisted Pair)
cable.

Caution: Do not connect with Internet or network devices

19

20

Limited Warranty

The DV-WPHXT-1ctx is warranted against failures due to defective parts or faulty workmanship for
a period of three years after delivery to the original owner. During this period, FSR will make any
necessary repairs or replace the unit without charge for parts or labor. Shipping charges to the
factory or repair station must be prepaid by the owner, return-shipping charges (via UPS Ground)
will be paid by FSR.

This warranty applies only to the original owner and is not transferable. In addition, it does not apply
to repairs done by other than the FSR factory or Authorized Repair Stations.

This warranty shall be cancelable by FSR at its sole discretion if the unit has been subjected to
physical abuse or has been modified in any way without written authorization from FSR. FSR’s
liability under this warranty is limited to repair or replacement of the defective unit.

FSR will not be responsible for incidental or consequential damages resulting from the use or
misuse of its products. Some states do not allow the exclusion of incidental or consequential
damages, so the above limitations may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.

Warranty claims should be accompanied by a copy of the original purchase invoice showing the
purchase date (if a Warranty Registration Card was mailed in at the time of purchase, this is not
necessary). Before returning any equipment for repair, please read the important information on
service below.

SERVICE
Before returning any equipment for repair, please be sure that it is adequately packed and

cushioned against damage in shipment, and that it is insured. We suggest that you save the original
packaging and use it to ship the product for servicing. Also, please enclose a note giving your name,
address, phone number and a description of the problem.

NOTE: all equipment being returned for repair must have a Return authorization (RMA)

Number. To get a RMA Number, please call the FSR Service Department (1-800-332-FSR1).

Please display your RMA Number prominently on the front of all packages.

CONTACT INFORMATION

244 Bergen Blvd.

Woodland Park, NJ 07424

Phone: [phone]

*Order Desk Fax: [phone]

E-mail: [e-mail]

Web Site: http://www.fsrinc.com

21