FSR CI-5 BWPA User Manual

REGULATORY COMPLIANCE

The Power Adapter has been tested for compliance with: UL, CSA and CE.

WARRANTY POLICY

This product is warranted against failures due to defective parts or faulty workmanship for a
period of three years after delivery to the original owner. During this period, FSR will make any
necessary repairs or replace the unit without charge for parts or labor. Shipping charges to
the factory or repair station must be prepaid by the owner, return-shipping charges, via UPS
/ FedEx ground, will be paid by FSR.

This warranty applies only to the original owner and is not transferable. In addition, it does not
apply to repairs done by other than the FSR factory or Authorized Repair Stations.

This warranty shall be cancelable by FSR at its sole discretion if the unit has been
subjected to physical abuse or has been modifi ed in any way without written authorization
from FSR. FSR’s liability under this warranty is limited to repair or replacement of the defec­tive unit.

FSR will not be responsible for incidental or consequential damages resulting from the use or
misuse of its products. Some states do not allow the exclusion of incidental or consequential
damages, so the above limitations may not apply to you. This warranty gives you specifi c legal
rights, and you may also have other rights which vary from state to state.

Warranty claims should be accompanied by a copy of the original purchase invoice
showing the purchase date (if a Warranty Registration Card was mailed in at the time of
purchase, this is not necessary). Before returning any equipment for repair, please read the
important information on service below.

SERVICE

CI-5 BWPA

CI-5LB

COMPUTER INTERFACE WALLPLATES WITH AUDIO

OPERATIONS MANUAL

Before returning any equipment for repair, please be sure that it is adequately packed and
cushioned against damage in shipment, and that it is insured. We suggest that you save the
original packaging and use it to ship the product for servicing. Also, please enclose a note
giving your name, address, phone number and a description of the problem.

NOTE: all equipment being returned for repair must have a Return Authorization

Please display your RMA Number prominently on the front of all packages.

Number (RMA). To get a RMA Number, please call the

FSR Service Department (973-785-4347).

Contact Information:

FSR INC.

244 Bergen Boulevard,

Woodland Park, NJ 07424

Tel: [phone] · Fax: [phone]

E-Mail: [e-mail] · Web:

http://www.fsrinc.com

43912

CI-5LB

CI-5BWPA

PROPRIETARY INFORMATION

All information in this manual is proprietary to and the
property of FSR inc. This publication is protected by
the Federal Copyright Law, with all rights reserved.
No part of this document may be reproduced,
transcribed, or transmitted, in any form or by any
means, without prior explicit written permission
from FSR inc.

LIT 1205A

INST ALLATION AND OPERA TION

The 5 BNC output cable, 9 VAC power supply leads and audio leads should be prewired
through the duplex back box prior to completing the steps below. Do not plug in the power
supply until all wiring is completed and proper connections are verifi ed.

Connect the 5 BNC female “pigtail” connectors to the 5 BNC male output cable leading to
the projector or monitor.

Connect the audio output cables to the captive screw terminals labeled “Audio Out”. The
appropriate wiring confi guration for balanced and unbalanced connections is shown in
Figure 1 to the right of this page.

Using the chart on the rear of the wallplate or below as a guide, set the cable equalization
dip switches for optimum performance at the desired cable length.

Connect the 9 VAC power supply output leads to the captive screw terminals labeled “9V”
and “AC”. Attach the video input from the desired source. Plug in the power supply. On
the units face, an amber LED will indicate power. The LED should change to green when a
proper video signal is present on the HD-15 input (horizontal sync is present).

After confi rming proper operation, unplug the power supply, and mount the CI–5 and cover
plate in the wall. Be certain that all cables and connectors are nested properly and check
for pinched or strained cables while mounting the CI - 5 interface into the wall box. Use the
supplied screws for mounting. Install the cover plate with the supplied screws and perform
the fi nal operational check.

AMBER LED INDICATES
POWER IS PRESENT

GREEN LED INDICATES
HORIZONTAL SYNC IS
PRESENT ON THE VIDEO
INPUT

DIP SWITCH

SETTINGS

OFF 0 0 50 0-75
LOW 0 1 100 75-125
MED 1 0 150 125-175

HIGH 1 1 200 175-200

POSITION

S2 S1

OPTIMAL CABLE

LENGTH (FT)

ACCEPTABLE CABLE

RANGE (FT)

SPECIFICATIONS

VIDEO INPUT

Number/type: 1 VGA / SVGA / XGA / SXGA / UXGA / RGBHV / RGBS / RGsB / RsGsBs
Connectors: One 15 pin HD female
Level (nominal): Analog 0.7v p-p
Level (maximum): 2v p-p
Impedance: 75 ohms

VIDEO OUTPUT

Number/type: 1 VGA / SVGA / XGA / SXGA / UXGA /

Connectors: 4” Pig-tail of 5 female BNC’s ( RGBHV )
Bandwidth: 700MHz @ -3.0dB (5 BNC output)

Level (nominal): Unity / User adjustable via DIP switch settings
Gain: OFF = 0’ to 75’ LOW = 75’ to 125’

Impedance: 75 ohms

AUDIO CI-5BWPA/CI-5LB PCI-5BWPA

Bandwidth: 20 Hz to 20 kHz (+/-0.05dB) 100 Hz to 15kHz (+/-2dB)
THD + Noise: 0.01% @ 20 kHz at rated Max Output S/N >98dB 0.5% between 275 Hz-3.5kHz
Noise Floor: Better than 98dB NA
Stereo separation: -90dB @ 1 kHz -40dB @ 1kHz
Audio Gain +6dB 0dB with 1.5dBm max insertion loss

AUDIO INPUT

Number/type: 1 stereo unbalanced 1 stereo unbalanced
Connectors: 1/8” mini connector 1/8” mini connector
Impedance: 10K ohms DC coupled unbalanced 600 ohms
Max level: +6dBm +20dBm

AUDIO OUTPUT

Number/type: 1 Balanced / Unbalanced Stereo 1 Balanced / Unbalanced Stereo
Connector: 5 Position Captive screw terminal 2, 3 position captive screw terminals
Impedance: 50 ohm
Maximum Level: 600 ohms: +12dBm Balanced / +6dBm Unbalanced 600 ohms

SYNC

Input level: 2.0v to 5.0v p-p
Output level: TTL to 5.0v p-p
Input Impedance: 475 ohms
Output impedance: 75 ohms
Polarity: Positive or negative
Horizontal frequency: 15kHz - 200kHz
Vertical frequency: 30 Hz - 150 Hz

GENERAL

Power: 9v AC / DC, 50/60 Hz: 8 – 14v DC, 9v AC Power Supply

Mounting: Single – Gang Decora Wallplate ( Included )
Colors: Black, White, Ivory
Enclosure Type: Metal
Size: 4.094” H x 1.706” W x 0.65” D
Approvals: UL / CE

RGBHV / RGBS / RsGsBs

400MHz @ -3.0dB (HD-15 loopback output)

MEDIUM = 125’ TO 175 HI = 175’ to +200’

Hi – Z: +14dBm Balanced / +8dBm Unbalanced +20dBm

included. May be remotely located up to 150 feet away from
the wallplate when using 22 Gage / 2 Conductor cable.

200200