FSR CB-SR12 Users Guide

5.

PRIOR TO PUSHING CEILING BOX INTO FRAME, APPLY BLUE PAINTERS TAPE (OR
EQUIVALENT) TO THE FRAME'S PAINTED BORDER, TO HELP PREVENT SCRATCHING THE
PAINT UPON BOX INSTALLATION. LINE UP THE BOX AND PUSH CEILING BOX UP INTO
FRAME. WHEN CEILING BOX REACHES THE STOPS ON THE INSIDE OF THE FRAME, PUSH
PINS INTO CAPTURE BRACKETS TO HANG BOX IN PLACE. IMPORTANT! - INSTALL PIN
LABELS, APPROXIMATELY WHERE SHOWN, ON BOTH SIDES. REFER TO CEILING BOX
INSTALLATION INSTRUCTIONS TO COMPLETE INSTALLATION. REMOVE TAPE ON
COMPLETION OF INSTALLATION.

(4) CAPTURE BRACKET

INSDE FRAME

CB-SR12 INSTALLATION INSTRUCTIONS

FSR

1.

INSTALLATION OF THE CB-SR12 CEILING FRAME REQUIRES A ROUGH-IN HOLE IN THE CEILING OF 13" x 25", +/- 1/16". THEHOLE'S
ROUGH-IN STRUCTURE NEEDS TO BE A MINIMUM OF 1-1/2" TALL, AND MAY BE MADE OF METAL OR WOOD.

THERE ARE 3 METHODS BY WHICH THE FRAME CAN BE RETAINED IN THE CEILING:

BY FOUR STEEL THREADED RODS, ONE PER CORNER OF THE FRAME, 1/4-20 THREAD MINIMUM TO 3/8-16 THREAD MAXIMUM,

1)
CENTERED ON A 11-1/2" x 23-1/2" RECTANGLE, AND EXTENDING DOWN TO WITHIN 2" TO 6" OF THE CEILING'S IN-ROOM SURFACE.

2) BY STEEL HANGER CABLE, 3/32"-DIAMETER MINIMUM, AND THREADED THRU THE FRAME'S APPROPRIATE SLOTS/HOLES IN
THE CORNERS OF THE UNIT.

3) BY SCREWS THRU THE APPROPRIATE HOLES IN THE CORNERS OF THE FRAME, INTO THE CEILINGS ROUGH-IN OPENING
STRUCTURE. TWO SCREWS, MINIMUM, PER CORNER.

THE SELECTED MOUNTING METHOD MUST BE ABLE TO SUPPORT A MINIMUM OF 500 LBS, AND BE APPROVED FOR
OVERHEAD LOADING.

THE STEPS REQUIRED TO MOUNT THE CEILING FRAME ARE:

A) DETERMINE THE MOUNTING METHOD APPROPRIATE FOR THE CEILNG CONSTRUCTION.
B) CREATE THE ROUGH-IN OPENING STRUCTURE AND INSTALL UNIT SUPPORTING HARDWARE AS NEEDED.
C) INSTALL CEILING/DRYWALL, TRIM TO ROUGH-IN OPENING.
D) TAPE/SPACKLE THE CEILING DRYWALL, AND PAINT IT IF THE CEILING COLOR IS TO BE DIFFERENT THAN THAT OF

THE CEILING FRAME'S VISIBLE WHITE ROUGH-IN-OPENING COVER.

E) INSTALL THE CEILING FRAME, THEN PROCEED TO INSTRUCTION STEP #2, AND COMPLETE THE UNIT INSTALLATION.

244 Bergen Boulevard, Woodland Park, NJ 07424, Phone: [phone] - Fax: [phone]

SLOTTED OPENING

FOR THREADED

ROD OR CABLE

HOLE FOR CABLE

PIN (UNLOCKED POSITION)

(2) PIN LABEL

INSTALL 2ND LABEL

ON OPPOSITE SIDE

CEINLING BOX UNLOCKED AND LOWERED

CEILING BOX RAISED AND LOCKED

THREADED ROD

FRAME CORNER DETAIL

(2) NUT &
(2) WASHER

THREADED ROD CABLE SCREW

QUICK ADJUST

CABLE CLAMP

HOLES FOR SCREWS

CABLE

SCREW

ROUGH-IN
STRUCTURE
(MINIMUM HEIGHT
SHOWN)

PIN (LOCKED POSITION)

43159 LIT1587A

2.

INSTALL BRACKETS INTO CEILING BOX (SOLD SEPARATELY). CEILING BOX
SHELVES WILL HAVE TO BE REMOVED FOR INSTALLATION OF BRACKETS
(SEE BRACKET DETAIL AND TOP VIEW). INSERT PINS INTO BRACKETS
UNTIL FLUSH WITH CEILING BOX EXTERIOR WALL (SEE PIN DETAIL).

(4) GUIDE
BRACKET
(NOTE CABLE
LOCATION)

(4) GUIDE BRACKET
ENSURE BRACKETS ARE
CORRECTLY LOCATED.
NOTE CABLE LOCATIONS
ON BRACKETS. CABLES
WILL BE LOCATED
FURTHEST FROM
CENTER OF BOX.

SIDE CONDUIT
KNOCKOUT

3.

ALIGN THE CEILING BOX, WITH ITS NEW BRACKETS, WITH THE CAPTURE BRACKETS
INSIDE FRAME. ATTACH 2 CABLES FROM CEILING BOX (NEAREST THE BOX'S KO'S) TO
FRAME AND ROUTE WIRING INTO CEILING BOX.

NOTE: ALL ELECTRICAL WIRES MUST DRAPE OVER THE TOP EDGE OF THE CEILING

BOX FRAME, NOT THRU THE SIDE OPENINGS. ONLY THE TOP-SURFACE KO'S
OF THE CEILING BOX MAY BE USED FOR THE WIRING.

CABLE INSTALLATION

(4) CABLE

TOP VIEW

LOOSEN SHELF SCREWS
AND REMOVE SHELVES TO
INSTALL PIN BRACKETS

CEILING BOX
(SOLD SEPARATELY)

SIDE CONDUIT
KNOCKOUT

a.

INSERT LARGE TAB
OF CABLE INTO
LARGE OPENING.

CABLE

c.

SLIDE CABLE
DOWNWARD TO
FLOOR.

OPENING
IN FRAME

b.

INSERT SMALL TAB
OF CABLE INTO
SMALL OPENING.

d.

INSTALL #6 SCREW
TO SECURE CABLE
TO FRAME.

(8) #8-32 x 3/8 LONG

PAN HEAD SCREW

(4) PIN BRACKET

(4) PIN

BRACKET DETAIL

GUIDE BRACKET

PIN DETAIL

(4) PIN
INSERT PIN UNTIL FLUSH
WITH EXTERIOR WALL
OF CEILING BOX

4.

AFTER ALL WIRING IS ROUTED TO CEILING BOX, ATTACH REMAINING CABLES TO FRAME.