FSR CB-224, CB-224S User Manual

CEILING TILE INSTRUCTIONS

8.

INSTALL 19-3/8" x 22-3/4" DROP CEILING MATERIAL (SUPPLIED
BY CUSTOMER) INTO DOOR. BEND CAPTURE TABS OVER
CEILING PANEL TO HOLD IN PLACE.

CB-224/224S INSTALLATION INSTRUCTIONS

FSR

1.

INSTALL CB-224/S TO A STRUCTURAL CEILING ABLE TO
SUPPORT FIVE TIMES THE NOTED GROSS WEIGHT. USE
APPROPRIATE MOUNTING METHODS BASED ON LOCAL
BUILDING CODES. INSTALL SAFETY CABLE AS REQUIRED BY
LOCAL BUILDING CODES. ROUTE CONDUITS TO BOX AS
REQUIRED.

NOTE: MAXIMUM GROSS WEIGHT - 125 LBS

244 Bergen Boulevard, Woodland Park, NJ 07424, Phone: [phone] - Fax: [phone]

STRUCTURAL
MEMBER

19-3/8" x 22-3/4" DROP

CEILING PANEL MATERIAL

(SUPPLIED BY CUSTOMER)

NOTE: THREADED ROD IS THE
RECOMMENDED CEILING BOX
MOUNTING SUSPENSION
(SHOWN), TO MINIMIZE
FIXTURE TILTING DUE
TO THE WEIGHT OF ANY
SUSPENDED EQUIPMENT.

14 GA. STEEL TIE WIRE MAY BE USED

(SUPPLIED BY CUSTOMER OR USE FSR KIT)

AT 70,000 PSI TENSILE STRENGTH OR

BETTER AS REQUIRED BY BUILDING CODES.

NOTE: WIRES SUPPORT CEILING

BOX, AND ARE NOT

THREADED ROD OR CABLE TO

BE PLUMB WITH CEILING AND FLOOR

AVAILABLE KITS (SOLD SEPARATELY):
CB-MNT1 - CABLE INSTALLATION KIT
CB-THRD - THREADED ROD INSTALLATION KIT

SAFETY CABLES

2.

TO INSTALL AC MAIN POWER INTO THE UNIT, REMOVE THE AC
ACCESS PLATE BY REMOVING (4) #8-32 SCREWS, AS SHOWN.
WIRING MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN
ONLY. WIRING MUST BE DONE IN ACCORDANCE WITH ALL NEC
AND OTHER APPLICABLE CODES. RE-INSTALL AC ACCESS
PLATE AFTER AC WIRING IS COMPLETE.

ALL MOUNTING HARDWARE
SUPPLIED BY CUSTOMER

STRUCTURAL
CHANNEL

ROUTE CONDUIT
(SUPPLIED BY
CUSTOMER) TO
KNOCKOUTS
AS REQUIRED

BRACKET - FSR'S
THREADED ROD
INSTALLATION KIT
(HARDWARE SUPPLIED
BY CUSTOMER)

(4) CAPTURE

TAB

LOOSEN SCREWS
TO OPEN DOOR

FSR Inc.

244 Bergen Boulevard, Woodland Park, NJ 07424
Phone: [phone] - Fax: [phone]
Web: www.fsrinc.com - E-mail: [e-mail]

(4) #8-32 x 1/4"-LONG
PAN HEAD SCREW

AC ACCESS

AC POWER INPUT WIRING MUST BE

PERFORMED BY A QUALIFIED

ELECTRICIAN ONLY

43972 LIT1364A

PLATE

3.

IF NOT INSTALLING FAN KIT, PROCEED TO STEP 5. IF INSTALLING FAN KIT,
REMOVE CEILING BOX DOOR. LOOSEN SCREWS TO OPEN DOOR. (a) PUSH
DOOR UP TOWARDS CEILING AND (b) PUSH TOWARDS DROP-DOWN
RACK-MOUNT CARRIAGE - REVERSE PROCEDURE TO INSTALL. DISCONNECT
SAFETY CABLE TO COMPLETELY REMOVE DOOR.

DROP-DOWN
RACK-MOUNT
CARRIAGE

MOUNTING ELECTRONICS INSTRUCTIONS

5.

PULL DOWN DROP-DOWN RACK-MOUNT CARRIAGE TO MOUNT ELECTRONICS.
(a) PUSH LOCK ARM AWAY FROM POLE MOUNT AND (b) AND PULL DOWN ON
CHAIN. ONCE THE DROP-DOWN CARRIAGE IS PULLED FULLY DOWN (c) AGAIN
PUSH THE LOCK ARM AWAY FROM POLE MOUNT TO LOCK CARRIAGE IN THE
'DOWN' POSITION. REVERSE PROCEDURE TO RETRACT CARRIAGE BACK INTO
CEILING BOX.

NOTE: MAXIMUM LOAD INSIDE CARRIAGE - 25 LBS

LOCK ARM

a

DROP-DOWN
RACK-MOUNT
CARRIAGE

b

a

LOOSEN SCREWS TO OPEN DOOR

4.

REMOVE #8-32 SCREW AS SHOWN, AND REMOVE OUTLET GRILL. SUPPORT
OUTLET GRILL WHILE REMOVING SCREW. INSTALL FAN KIT PER INSTRUCTIONS.
RE-INSTALL OUTLET GRILL AND CEILING BOX DOOR BACK INTO CEILING BOX BY
REVERSING THEIR REMOVAL STEPS.

PULL CHAIN

b

6.

INSTALL WIRE BUNDLE INLET, WIRE
INLET FOAM, AND WIRE INLET COVER
TO SIDES OF BOX. REMOVE THE FOAM
BLOCKS NECESSARY FOR THE WIRE
BUNDLE EXITING THE BOX. PULL
WIRES TO CEILING BOX THRU WIRE
INLET OR CONDUIT AS REQUIRED.

(2) WIRE

INLET

COVER

REMOVABLE

(2) WIRE

INLET
FOAM

FOAM BLOCKS

(2) WIRE
BUNDLE
INLET

c

7.

INSTALL 1RU TO 4RU x 19" EIA RACK-SIZED ELECTRONICS.
MAKE ELECTRICAL CONNECTIONS AS REQUIRED. RACK
MOUNT BRACKETS CAN BE RE-POSITIONED TO ALTERNATE
HOLES, OR ADDITIONAL BRACKETS MAY BE PURCHASED
(CB-224RKRL).

NOTE: MAXIMUM LOAD INSIDE CARRIAGE - 25 LBS

ALTERNATE
RACK MOUNT
BRACKET HOLES

#8-32 x 1/4"-LONG

PAN HEAD SCREW

OUTLET GRILL

(2) #8-32 x 1/4-LONG

PAN HEAD SCREW

(4) RACK
MOUNT
BRACKET
INCLUDED

VIEW SHOWING

ALTERNATE

BRACKET

HOLES USED

ALTERNATE/ADDITIONAL
RACK MOUNT BRACKET
HOLES ON OPPOSITE
SIDE OF CARRIAGE