FSR CB-22 User Manual

CB-22 INSTALLATION INSTRUCTIONS

CB-22 INSTALLATION INSTRUCTIONS

FSR

1.

INSTALL CB-22 TO A STRUCTURAL CEILING ABLE TO SUPPORT
FIVE TIMES THE NOTED GROSS WEIGHT. USE APPROPRIATE
MOUNTING METHODS BASED ON LOCAL BUILDING CODES.
INSTALL SAFETY CABLE AS REQUIRED BY LOCAL BUILDING
CODES. ROUTE CONDUITS TO BOX AS REQUIRED.

244 Bergen Boulevard, Woodland Park, NJ 07424, Phone: [phone] - Fax: [phone]

STRUCTURAL
MEMBER

NOTE: MAXIMUM GROSS WEIGHT - 120 LBS

NOTE: THREADED ROD IS THE
RECOMMENDED CEILING BOX
MOUNTING SUSPENSION
(SHOWN), TO MINIMIZE
FIXTURE TILTING DUE
TO THE WEIGHT OF ANY
SUSPENDED EQUIPMENT.

14 GA. STEEL TIE WIRE MAY BE USED

(SUPPLIED BY CUSTOMER OR USE FSR KIT)

AT 70,000 PSI TENSILE STRENGTH OR

BETTER AS REQUIRED BY BUILDING CODES.

BE PLUMB WITH CEILING AND FLOOR

AVAILABLE KITS (SOLD SEPARATELY):
CB-MNT1 - CABLE INSTALLATION KIT
CB-THRD - THREADED ROD INSTALLATION KIT

2.

TO INSTALL AC MAIN POWER INTO THE UNIT, REMOVE THE
AC ACCESS PLATE BY REMOVING (4) #8-32 SCREWS, AS
SHOWN. WIRING MUST BE PERFORMED BY A QUALIFIED
ELECTRICIAN ONLY. WIRING MUST BE DONE IN
ACCORDANCE WITH ALL NEC AND OTHER APPLICABLE
CODES. RE-INSTALL AC ACCESS PLATE AFTER AC WIRING IS
COMPLETE.

NOTE: WIRES SUPPORT CEILING

BOX, AND ARE NOT

THREADED ROD OR CABLE TO

SAFETY CABLES

ROUTE CONDUIT

(SUPPLIED BY

CUSTOMER) TO

AS REQUIRED

KNOCKOUTS

3.

ALL MOUNTING HARDWARE
SUPPLIED BY CUSTOMER

STRUCTURAL
CHANNEL

BRACKET - FSR'S
THREADED ROD
INSTALLATION KIT
(HARDWARE SUPPLIED
BY CUSTOMER)

REMOVE CEILING BOX DOOR. INSTALLATION OF
19-3/8" x 22-3/4" DROP CEILING PANEL MATERIAL INTO
DOOR CAN BE DONE NOW, WHILE DOOR IS OFF, OR
DURING RE-ASSEMBLY. BEND CAPTURE TABS OVER
CEILING PANEL TO HOLD IN PLACE.

SHELF

b

19-3/8" x 22-3/4"

DROP CEILING

PANEL MATERIAL

(SUPPLIED BY

CUSTOMER)

(4) CAPTURE TAB

AC ACCESS

AC POWER INPUT

WIRING MUST BE

PERFORMED BY

A QUALIFIED

ELECTRICIAN ONLY

43192 LIT1321B

PLATE

(4) #8-32 x 1/4"­LONG PAN
HEAD SCREW

LOOSEN SCREWS

TO OPEN CB-22 DOOR

DISCONNECT

SAFETY CABLE

TO COMPLETELY

REMOVE DOOR

DOOR IS

REMOVABLE.

a

(a) PUSH DOOR

UP TOWARDS

CEILING AND

(b) PUSH

TOWARDS

SHELF -

REVERSE

PROCEDURE

TO INSTALL

FSR

CB-22 MOUNTING ELECTRONICS

244 Bergen Boulevard, Woodland Park, NJ 07424, Phone: [phone] - Fax: [phone]

4a.

REMOVE SHELF, AND MOUNT ELECTRONIC S TO SHEL F.
USE HOLE/SLOT PATTERN ON SHELF TO MOUNT
EQUIPMENT. ADDITIONAL HOLES MAY BE REQUIRED.
SEE 4b. FOR INSTALLING RACK MOUNTED UNITS.
RE-INSTALL SHELF INTO CB-22. MAKE ELECTRICAL
CONNECTIONS AS REQUIRED.

NOTE: MAXIMUM LOAD PER SHELF - 20 LBS EACH

LOOSEN SCREWS (4 PER SHELF)
TO REMOVE SHELVES

(2) SHELF

a

LOOSEN SHELF

SCREWS. (a) PUSH

SHELF TOWARDS

DOOR AND (b)

SHELF WILL DROP

DOWN OUT OF

CB-22

b

HOLES FOR ALTERNATE

LOCATION OF SHELVES

4b.

FOR 1RU x 19" EIA RACK-SIZED ELECTRONICS, INSTALL
RACK MOUNT BRACKETS AS SHOWN. INSTALL RACK
UNIT AND RE-INSTALL SHELF INTO CB-22. MAKE
ELECTRICAL CONNECTIONS AS REQUIRED.

NOTE: MAXIMUM LOAD PER SHELF - 20 LBS EACH

LEFT RACK

MOUNT

BRACKET

TOWARDS

BOX BLANK

END

RIGHT RACK
MOUNT
BRACKET

SHELF

ALTERNATE MOUNTING

(4) #10-32 x 3/8"-LONG
PAN HEAD SCREW

43192 LIT1321B

HOLES FOR RACK

MOUNT BRACKETS