Frsky ESC Neuron 60S, ESC Neuron 40S User Manual

Instruction Manual for ESC Neuron 40S/60S

Introduction

Thank you for purchasing FrSky ESC Neuron 40S/60S. The ESC has high performance processor. The SBEC voltage can be adjusted through LUA (FrOS & OpenTX Supported) or through FreeLink App with Airlink S. The Neuron ESC is encased in a CNC aluminum protective shell which also aids in heat dissipation. In order to fully enjoy the benefits of the products, please read the instruction manual carefully and set up the device as described below.

Overview

Neuron 40

Note: 1. The jumper cap as a switch makes ESC output power When you connect the JP.

2. The jumper cap has internal resistance which may bring reduction voltage.

GND

Left

BEC 5~8.4V PWM

S.Port JP

Specifications

Model Name Size (L×W×H) LiPo cells SBEC Cont. CurrentWeight Peak Current

Neuron 40S

Neuron 60S

39*19*11mm

44*22*12mm

Maximum supported speeds:

Dshot at 8kHz

Dshot at 16kHz

Dshot at 32kHz

Dshot at 16kHz with sine

Erpm

470k

420k

310k

280k

32.2g

37.7g

Multishot at 8kHz

Multishot at 16kHz

Multishot at 32kHz

3~6S

Erpm

510k

450k

420k

5~8.4V

Proshot at 8kHz

Proshot at 16kHz

Proshot at 32kHz

40A

60A

Erpm

Regular pwm input signal

480k

430k

330k

Regular at 8kHz

Regular at 16kHz

Regular at 32kHz

50A

80A

Erpm

510k

450k

420k

Programming parameters

FrSky

ESC Neuron 40S/60S

included in the package.Users could buy BLHeli USB Linker on your own. The connection diagram is below.

Never connect the 5V output from USB adapter to ESC, or ESC will not work normally.

The configuration method based on the operation manual for BLHeli_32 ARM is only for reference. For more detailed information, please refer to the original BLHeli manual carefully. Due to firmware update or other reasons, the descriptions for functions may differ, so please take the official BLHeli manual as standard.

supports programming parameters through USB Adapter. USB Adapter is not

GND

Neuron XX

Features

• Smart Port enabled

Telemetry data for ESC: Voltage, Current (Resolution 125mA, Precision ±2%), RPM, Power Consumption, Temperature. Telemetry data for SBEC: Output Voltage, Current (Resolution 50mA, Precision ±2%)

• High performance 32-bit micro-processor

• Over-temperature and over-current protection

• SBEC Supports 5A@5~8.4V (adjusted through

LUA or through FreeLink App with Airlink S)

Connection Diagram

Receiver

Battery

Warning:

Please DO NOT connect BEC to any devices with power supply.

FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us : frsky@frsky-rc.com Add:F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: sales4tech@gmail.com

ESC

Motor

Rampup Power can be set to relative values from 3% to 150 %. 3% is the minimu m power to s tart the e ngine and 150% is th e max imum power to operate the motor normally.

Temp er atu re pr ot ectio n can b e d is ab led o r ena bl ed an d t em pe rat ur e thresh old c an be program med. The m easured ma ximum tempera ture is different because the hardware are not the same.

Instruction Manual for ESC Neuron 40S/60S

Demag Compensation is meant to protect the motor from stalling which is caused by over demagnetization of coils. A sudden and sharp increase of throttle (especially at low RPM) will lead to the stalling or stutter of the motor. Under the circumstance, Demag Compensation is an appropriate way to fix the problem.

Motor Timing can be set from 1% to 31% with 10 increments or operate automatically. A medium setting could make the motor work perfectly, however, if the motor stutters, it is advised to increase timing.

Maximum Acceleration can be set between 0.1%/ms and 25.5%/ms. It can also be set to maximum, thus acceleration is not limited. It functions as a backup parameter. For example, if the setting goes to 10.0%/ms, it means the power of the motor is not allowed to increase by more than 10% per millisecond.

The Minimum Throttle can be adjusted from 900 to 1615. The value for the settings ( Minimum Throttle, Maximum Throttle and Center Throttle) are designed for normal input signal (from 1000 s to 2000 s). For other input signal, the value must be scaled. For Dshot iuput signal, the setting doesn’t work.

Instruction Manual for ESC Neuron 40S/60S

Sets the delay before beacon beeping starts.

The PWM frequency of motors could be programmed between 16kHz and 48 kHz. Higher PWM frequency will make motors run smoother.

Smart Port

All data measured by S. Port supported products could be passed back to the transmitter.

Smart Port (S. Port) is a signal wire full duplex digital transmission interface developed by FrSky Electronic Co., Ltd. All products enabled with Smart Port (including XJT module, RX8R receiver, new hub-less sensors, new Smart Dashboard, etc), serial port user data and other user input/output devices can be connected without limitations for numbers or sequences at a high transmis sion speed.

Here are the interface of parameter configuration and feedback on OpenTX.

Parameter configuration Telemetry feedback

Here is the interface of FreeLink You can download the APP.

The Maximum Throttle can be adjusted from 1140 to 2100.

The Center Throttle can be adjusted from 1001 to 2099. It is only used for bidirectional operation.

Brake On Stop can be set between 1% and 100% or inhibited.

The continuous and frequent throttle stick movements (switch between the maximum and minimum values ) under the braking function activated in a very short time would damage the products,you should be careful the function enable.

Sets the strength of beacon beeps. The ESC will make beacon beeps of the signal of throttle has been zero for a given time. Note that set a high beacon stength will lead to the heating of motors and the ESC.

Android FreeLink APPIOS FreeLink APP

Warnings

•

Before using the ESC, please read through the manuals of all power devices and models. Ensure rational power

configuration, or it will make the unit overloaded and damaged.

•

Always keep your model away from unsafe elements, such as concrete buildings and high-voltage power lines.

Fly your models according to the manual strictly, or it may cause damage and serious injuries.

•

Always disconnect the batteries from the ESC after use, or it may drive the motor to rotate and cause injuries. If the ESC is connected to the battery for a long time, the battery will be fully discharged, which may lead to the malfunction of both batteries and the ESC.

Frsky ESC Neuron 60S, ESC Neuron 40S User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual