Frontier FiOS Arris NVG468MQ, FiOS Arris MEB1100 Quick Setup Manual

®
®
FiOS by Frontier Router and Optional MoCA Adapter
Arris NVG468MQ Arris MEB1100
QUICK SETUP GUIDE
Power Adapter (1)
Coax Cable (3) Ethernet Cable (1) USB Cable (1)
Splitter (1)
MoCA Adapter (1)
FiOS Router (1)
FiOS Router (1)
Power Adapter (1)
Coax Cable (1)
NEXT:
Proceed to Step 2
If you don't have the MoCA adapter, check your packaging contents and make sure you have the following:
Ethernet Cable (1)
NEXT:
Proceed to Step 2
STEP 1 Check your Config
Your new FiOS® by Frontier® Data service could be configured using Ethernet or MoCA from the Optical Network Terminal (ONT) to your FiOS Router. Check your packaging contents. If you have a MoCA Adapter, make sure you have the following:
A. Connect the MoCA Adapter and the Router
1. Connect a Coax cable from the wall jack to the side of the Splitter (Coax In) with a single port.
2. Connect the second Coax cable to one of the remaining ports on the Splitter (Coax Out) and then to the port on
back of the MoCA adapter labeled "ONT Broadband".
3. Connect the third Coax cable to a remaining port on the Splitter and then to the port on the back of the Router
labeled "Cable Line".
4. Connect the Ethernet Cable to the RED port on the MoCA adapter labeled "RG Broadband" and then to the RED
port on the Router Labeled "ONT Broadband"
5. Connect the USB cable to the port on the MoCA adapter labeled "Power" and
then to the port on the Router labeled "USB".
Coax
Coax
Coax
USB
Ethernet
MoCA
Adapter
Router
Splitter
STEP 2
CONNECT YOUR ROUTER
New
Customers configured with
a
MoCA
Adapter:
Coax
(if used)
STB
New Customers configured without a MoCA Adapter:
A. Connect the Router
1. Connect one end of the WHITE Ethernet cable to the Ethernet port on your wall (or the Optical Network
Terminal (ONT) if the Router is located next to the ONT). Next, connect the other end of your cable to the RED Ethernet port labeled “ONT” on your router.
2. Connect a Coax cable from the wall jack then to the port on the back of the Router labeled "Cable Line" if
subscribed to TV service.
Coax
Router
Ethernet
B. Connect Power to the Router
Plug the power adapter into the port labeled "Power" on the router and then plug the power adapter into a power outlet. Press the power button on the back of the router to turn it on.
C. Check for Internet Connectivity
The Internet light on the front of the FiOS Router will become solid BLUE once you have Internet connectivity.
If after several minutes the light is not solid BLUE, check the troubleshooting steps on the back of this guide.
C
B
STEP 3
CONNECT DEVICES TO THE ROUTER
Wired:
Connect one end of an Ethernet cable to any YELLOW Ethernet port on the Router and then connect the other end to the Ethernet port on your device.
Wireless:
You will find the Wireless network names and password details on the sticker on the BOTTOM of your router. Go to your device’s Wi-Fi settings and select a Wi-Fi network name that matches your router from the list of available wireless networks. Enter the Wi-Fi password to securely connect your device to your Router.
Sample image, use
credentials on the
router
CONGRATULATIONS
YOU HAVE SUCCESSFULLY
INSTALLED AND CONFIGURED YOUR ROUTER.
To learn more, go to
frontier.com/helpcenter
CONGRATULATIONS YOU HAVE SUCCESSFULLY
INSTALLED AND CONFIGURED YOUR ROUTER.
To learn more, go to frontier.com/helpcenter
Note: You will be asked to enter the Device Access Code (located on the bottom of the Router) if you make changes to these settings.
Please also note any changes you've made to the router in the event you need support.
Sample image, use
credentials on the router
STEP 4
(optional)
PERSONALIZE ROUTER
Open a web browser and type in "http://192.168.254.254". This will launch the main status page for the Router that also allows you to personalize your settings, such as your Wi-Fi name or
password.
Home Wiring Connections
Frontier® uses an Optical Network Terminal (ONT) and a Router to connect your home to the Internet and enable Data, Voice, and TV Services. If the steps above do not result in an Internet connection, check the cables on the ONT.
Ethernet-connected homes will require BOTH Ethernet and Coax connections from the ONT to the Router for TV service.
Confirm the Coax connector on the ONT is securely connected to the home wiring used by the router (or directly to the Router). Many ONT's require this connection for both Data and TV services.
Confirm the Ethernet connector on the ONT is securely connected to the home wiring used by the router (or directly to the Router). Many ONT's require this connection for Data services.
To determine if the ONT is provisioned for Ethernet or MoCA, look for the light on the ONT:
- DATA light ON: Ethernet is provisioned
- MoCA or HPNA light ON: Coax is
provisioned
Example ONT Image
Example Router Image
Example Back of
Router Image
PROBLEM: INTERNET LIGHT DOES NOT BECOME SOLID BLUE.
PROBLEM: UNABLE TO CONNECT TO THE WI-FI NETWORK.
PROBLEM: CHANNEL GUIDE IS NOT UPDATING
PROBLEM: I HAVE QUESTIONS NOT COVERED IN THIS GUIDE.
SUPPORT: Videos are available at frontier.com/
helpcenter. Detailed instructions on setting up a
home wireless network are available at frontier.com/
helpcenter.
© 2017 Frontier Communications Corporation. All rights reserved. Q4_2017
SOLUTION: Make sure all coaxial (Coax) connections from the Optical Network Unit
(ONT) to home wiring and to the Router and Set Top Box are connected.
SOLUTION: Make sure the Coax cables are securely fastened to the Wall, Splitter,
MoCA adapter and Router.
SOLUTION: Make sure the white
Ethernet cable
is connected to the RED Ethernet port
on the Router labeled "ONT Broadband"
(not to the yellow Ethernet ports)
SOLUTION: Make sure the Coax cables are securely fastened to the Wall, Splitter,
MoCA adapter and Router.
SOLUTION: Make sure you are selecting the Wi-Fi network printed on the sticker on
the bottom of the Router.
SOLUTION: Make sure you are correctly entering your Wi-Fi password
(password is case-sensitive, make sure Caps Lock is off).
SOLUTION: Make sure the Coax cable is securely fastened between the Splitter and
the Router
SOLUTION:
Please call the Frontier helpdesk at
1.800.921.8101.
02958_11_Finstallguide_1217
TROUBLESHOOTING
PROBLEM: INTERNET LIGHT DOES NOT BECOME SOLID BLUE.
PROBLEM: UNABLE TO CONNECT TO THE WI-FI NETWORK.
PROBLEM: CHANNEL GUIDE IS NOT UPDATING
PROBLEM: I HAVE QUESTIONS NOT COVERED IN THIS GUIDE.
SUPPORT: Videos are available at frontier.com/helpcenter. Detailed instructions on setting up a home wireless network are available at frontier.com/helpcenter.
© 2017 Frontier Communications Corporation. All rights reserved. Q4_2017
SOLUTION: Make sure all coaxial (Coax) connections from the Optical Network Unit
(ONT) to home wiring and to the Router and Set Top Box are connected.
SOLUTION: Make sure the Coax cables are securely fastened to the Wall, Splitter,
MoCA adapter and Router.
SOLUTION: Make sure the white
Ethernet cable
is connected to the RED Ethernet port
on the Router labeled "ONT Broadband"
(not to the yellow Ethernet ports)
SOLUTION: Make sure the Coax cables are securely fastened to the Wall, Splitter,
MoCA adapter and Router.
SOLUTION: Make sure you are selecting the Wi-Fi network printed on the sticker on
the bottom of the Router.
SOLUTION: Make sure you are correctly entering your Wi-Fi password
(password is case-sensitive, make sure Caps Lock is off).
SOLUTION: Make sure the Coax cable is securely fastened between the Splitter and
the Router
SOLUTION:
Please call the Frontier helpdesk at 1.800.921.8101.
02958_11_Finstallguide_1217
Loading...