Frigidaire FGC6X9XGTA Installation Instruction
GAS COOKTOP INSTALLATION INSTRUCTIONS
(Models with Optional Electric Built-In Oven Combination)
INSTALLATION AND SERVICE MUST BE PERFORMED BY
A QUALIFIED INSTALLER.
IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
If the information in this manual is not followed exactly, a fire or explosion may result
causing property damage, personal injury or death.
FOR YOUR SAFETY:
— Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
— WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
— Installation and service must be performed by a qualified installer, service agency or the gas supplier.
Cooktop Dimensions
* 30" min. for unprotected cabinet
24" min. for protected surface
A
Cooktop Cutout Dimensions
L
E
M
Figure 1
MODEL
30" Models 30 (76.2) 21 ½ (54.6) 3
36" X 21½" Models 36 (91.4) 21 ½ (54.6) 3
36"X 18" Models 36 (91.4) 18 (45.7) 3 ½ (8.9) 34 ¼ (87) 34
A.
LENGTH
B. WIDTH C. DEPTH
1
/8 (7.9) 26 5/8 (67.6) 26 7/8 (68.3) 19 (48.3) 19 3/8 (49.2) 5 (12.7) 2¾ (7) 2¼ (5.7)
1
/8 (7.9) 32 ¾ (83.2) 33 (83.8) 19 (48.3) 19 3/8 (49.2) 5 (12.7) 2¾ (7) 2¼ (5.7)
MIN. D. LENGTH MAX.
30" Min.*
B
(76.2 cm) Min.*
C
F
D
CUTOUT DIMENSIONS
MIN. E. WIDTH MAX.
3
/8 (87.3) 16 5/8 (42.2) 16 ¾ (42.5) 5 (12.7) 4¼ (10.8) 3 (7.6)
F. DEPTH
BELOW
COOKTOP*
L
(Min.)M(Min.)
All dimensions are in inches (cm).
Dimension F is for clearance under cooktop for gas connection.
NOTE: Wiring diagrams for these appliances are enclosed in this booklet.
Only some models are available in Canada.
Recycled paper
1
P/N 318201450 (0410) Rev. B
English – pages 1-8
Español – pages 9-17
Français – pages 18-26
Wiring Diagrams - pages 27-28
13" (33 cm)
Max. Depth For
Cabinet Installed
Above Cooktop.
GAS COOKTOP INSTALLATION INSTRUCTIONS
(Models with Optional Electric Built-In Oven Combination)
A
Min.
30" (76.2 cm) Min.
Clearance Between
the Top of the
Cooking Platform
and Unprotected
Wood or Metal
Cabinet
Dimension K is the
Minimum Clearance
Required From Left
Side To Adjacent
Combustible Surface.
18" Min.
(45.7cm Min.)
24" (61 cm)
Dimensions J is the Minimum
Distance Required Between Rear
of Cooktop to Adjacent
Combustible Surfaces.
Clearance
Dimension H is the
Minimum Clearance
Required From Right
Side To Adjacent
Combustible Surface.
To eliminate the risk of
burns or fire by reaching over heated
surfaces, cabinet storage space located
above the cooktop should be avoided. If
cabinet storage is provided, risk can be
reduced by installing a range hood that
projects horizontally a minimum of 5"
(12.7 cm) beyond the bottom of the
cabinets.
Figure 2 – COUNTERTOP CUTOUT OPENING
MODEL H J K
30" Models 4" (10.2 cm) 1 ½" (3.8 cm) 7" (17.8 cm)
36" X 21½" Models 5" (12.7 cm) 1 ½" (3.8 cm) 5" (12.7 cm)
36" X 18" Models 3" (7.6 cm) 3 ¾" (9.5 cm) 3" (7.6 cm)
2
GAS COOKTOP INSTALLATION INSTRUCTIONS
(Models with Optional Electric Built-In Oven Combination)
Important Notes to the Installer
1. Read all instructions contained in these installation
instructions before installing the cooktop.
2. Remove all packing material before connecting the
electrical supply to the cooktop.
3. Observe all governing codes and ordinances.
4. Be sure to leave these instructions with the consumer.
Important Note to the Consumer
Keep these instructions with your Use and Care Guide for
future reference.
IMPORTANT SAFETY
INSTRUCTIONS
Installation of this cooktop must conform with local codes
or, in the absence of local codes, with the National Fuel
Gas Code ANSI Z223.1—latest edition in the United
States, or in Canada, with the Canadian Fuel Gas Code,
CAN/CGA B149 and CAN/CGA B149.2.
This cooktop has been design certified by American Gas
Association (A.G.A.). As with any appliance using gas
and generating heat, there are certain safety precautions
you should follow. You will find them in the Use and
Care Guide, read it carefully.
• Be sure your cooktop is installed and grounded
properly by a qualified installer or service
technician.
• This cooktop must be electrically grounded in
accordance with local codes or, in their absence,
with the National Electrical Code ANSI/NFPA No.
70—latest edition in the United States, or in
Canada, with the Canadian Electrical Code, CSA
C22.1 Part 1.
• The burners can be lit manually during an
electrical power outage. To light a burner, hold a
lit match to the burner head, then slowly turn the
Surface Control knob to LITE. Use caution when
lighting burners manually.
• Do not store items of interest to children in the
cabinets above the cooktop. Children could be
seriously burned climbing on the cooktop to reach
items.
• To eliminate the need to reach over the surface
burners, cabinet storage space above the burners
should be avoided.
• Adjust surface burner flame size so it does not
extend beyond the edge of the cooking utensil.
Excessive flame is hazardous.
• Never use your cooktop for warming or heating
the room. Prolonged use of the cooktop without
adequate ventilation can be hazardous.
• Do not store or use gasoline or other flammable
vapors and liquids near this or any other
appliance. Explosions or fires could result.
The electrical power to the cooktop
must be shut off while line connections are being
made. Failure to do so could result in serious
injury or death.
1. Before Installing the Cooktop
COOKTOP
Foam Tape
Figure 3
A roll of foam tape is supplied loose and packed in the
literature package. Install the foam around the
perimeter of the flange of the burner box, at a distance
of ¼" (0.6 cm) from the edge of the glass or porcelain
top. Apply the exposed adhesive side of the tape
against the underside of the glass or the burner box
surface (see figure 3).
NOTE: This tape seals the underside of the cooktop to
the counter. Do not remove this foam tape. This
tape prevents entry of air for normal gas combustion,
and prevents liquids from leaking under the cooktop.
After inserting the cooktop into the countertop
opening, make sure the unit is sitting on the metal
flange around the top of the burner box. Cooktop
must not sit on the glass or porcelain top. Avoid
cutting an oversized hole in the countertop.
3
GAS COOKTOP INSTALLATION INSTRUCTIONS
All mounting hardware
must be used to secure
the built-in oven to the
cabinets. Refer to the
built-in oven installation instructions.
(Models with Optional Electric Built-In Oven Combination)
Side filler panels are necessary to isolate the
unit from adjoining cabinets. Panel height
should allow for installation of approved
This cooktop may be installed over certain builtin electric oven models.
cooktop models. See “Typical Gas Cooktop Installation Over an Electric Built-in Oven Installed
Under the Counter” in this booklet.
Approx. 3”
(7.6 cm)
36” Min.
(91.4 cm Min.)
32” Min.**
(81.3 cm Min.**)
208/240 Volt grounded
junction box for built-in
oven.
4 ½” Max.*
(11.4 cm Max.*)
* If no cooktop is installed directly over
the oven unit, 5” (12.7 cm) maximum
is allowed.
** 32" (81.3 cm) min. from top of cabinet
to top of runners must be maintained.
G
E
F
Use ¾” (1.9 cm) plywood, installed on two
runners, flush with toe plate. Must be capable
of supporting 150 lbs (68 kg).
Cut an opening in wood base minimum 9” x 9” (22.9 cm X 22.9 cm),
2” (5.1 cm) from left side filler
panel, to route armoured cable to
junction box.
CUTOUT DIMENSIONS
MODEL E. HEIGHT F. WIDTH G. DEPTH
27" (68.6 cm)
Wall Oven
1
28
/8" (71.4 cm) Min.
5
/8" (72.7 cm) Max.
28
7
24
/8" (63.2 cm) Min.
25 ¼" (64.1 cm) Max.
23 ½"(59.7 cm)
30" (76.2 cm)
Wall Oven
28 ¼" (71.8 cm) Min.
7
/8" (73.3 cm) Max.
28
28 ½" (72.4 cm) Min.
29" (73.7 cm) Max.
Figure 4 – TYPICAL UNDER COUNTER INSTALLATION OF AN ELECTRIC BUILT-IN OVEN
WITH COOKTOP MOUNTED ABOVE
4
24" (61 cm)
GAS COOKTOP INSTALLATION INSTRUCTIONS
(Models with Optional Electric Built-In Oven Combination)
18” Max.
(45.7 cm)
GAS COOKTOP
Flexible Connector
Wall Oven Cabinet
Figure 5 – TYPICAL GAS COOKTOP INSTALLATION OVER
AN ELECTRIC BUILT-IN OVEN INSTALLED UNDER THE COUNTER
2. Wall Outlet Location
12" (30.5 cm)
8"
(20.3 cm)
Cabinet sides or
filler panel
Flare
Union
4” (10.2 cm)
5” Max.
(12.7 cm)
6 ½” Min.
(16.5 cm)
Flare
Union
120V/60Hz
Grounded
Outlet
Pressure
Regulator
Manual
Shutoff
Valve
Right Side of
Cabinet
(To be
accessible for
shut-off valve
operation)
3. Clamp Down Information
Once the cooktop is installed in the counter opening, you
must clamp the unit down as shown.
Countertop
Cooktop Foam Tape
NOTE: If an outlet
is not available,
have one installed
by a qualified
technician.
10" (25.4 cm)
Recommended area for
120V grounded outlet on
rear wall
C
L of unit
C
L of unit
Figure 6
22"
(55.9 cm)
Angle Bracket
Thumb Screw
Figure 7
To clamp down, insert the bracket with the offset side of
the angle into the slots on each side of the unit. The
thumb screw should then be run through the bracket, up
against the bottom of the counter. Tighten until the unit
draws down.
5
GAS COOKTOP INSTALLATION INSTRUCTIONS
(Models with Optional Electric Built-In Oven Combination)
4. Provide an Adequate Gas Supply
This cooktop is designed to operate on natural gas at 4"
(10.2 cm) of manifold pressure only.
A pressure regulator is connected in series with the
manifold on the cooktop and must remain in series with
the supply line.
For proper operation, the maximum inlet pressure to
the regulator must be no more than 14" (35.6 cm) of
water column (W.C.) pressure.
For checking the regulator, the inlet pressure must be at
least 1" (2.5 cm) (or 2.5 kPa) greater than the regulator
manifold pressure setting. The regulator is set for 4"
(10.2 cm) of manifold pressure, the inlet pressure must
be at least 5" (12.7 cm).
The gas supply line to the cooktop should be ½" (1.3
cm) or ¾" (7.9 cm) pipe.
5. LP/Propane Gas Conversion
This appliance can be used with Natural gas or LP/
Propane gas. It is shipped from the factory for use with
natural gas.
If you wish to convert your cooktop for use with LP/
Propane gas, use the supplied fixed orifices in the
package containing the installation Instructions Manual,
in a bag marked "FOR LP/PROPANE GAS CONVERSION".
Follow the installation instructions packaged with the
orifices.
6. Install Pressure Regulator
Install the pressure regulator with the arrow on the
regulator pointing up toward the unit in a position where
you can reach the access cap.
FIRE HAZARD. Do not make the
connection too tight. The regulator is die cast.
Overtightening may crack the regulator resulting in a gas
leak and possible fire or explosion.
Manual
Shutoff
Valve
On
Assemble the flexible connector from the gas supply pipe
to the pressure regulator in order: 1- manual shutoff
valve, 2- ½" nipple, 3- ½" flare union adapter, 4flexible connector, 5- ½" flare union adapter, 6- ½"
nipple, pressure regulator.
Use pipe-joint compound made for use with Natural and
LP/Propane gas to seal all gas connections. If flexible
connectors are used, be certain connectors are not
kinked.
Flare
Union
Off
All connections must be wrench-tightened
GAZ FLOW
Flexible Connector
Figure 8
Flare
Union
Pressure
Regulator
The conversion must be performed by a qualified service
technician in accordance with the manufacturer's
instructions and all local codes and requirements of the
authority having jurisdiction. Failure to follow
instructions could result in serious injury or property
damage. The qualified agency performing this work
assumes responsibility for the conversion.
Failure to make the appropriate
conversion can result in personal injury and property
damage.
Important: Remove all packing material and
literature from cooktop before connecting gas and
electrical supply to cooktop.
The supply line should be equipped with an approved
shutoff valve. This valve should be located in the same
room as the cooktop and should be in a location that
allows ease of opening and closing. Do not block access
to the shutoff valve. The valve is for turning on or
shutting off gas to the appliance.
To Appliance
Shutoff Valve
Figure 9
Open the shutoff valve in the gas supply line. Wait a
few minutes for gas to move through the gas line.
To gas supply line
6
GAS COOKTOP INSTALLATION INSTRUCTIONS
(Models with Optional Electric Built-In Oven Combination)
Check for leaks. Leak testing of the appliance shall be
conducted according to the manufacturer's instructions.
After connecting the cooktop to the gas supply, check
the system for leaks with a manometer. If a manometer
is not available, turn on the gas supply and use a liquid
leak detector (or soap and water) at all joints and
connections to check for leaks.
Do not use a flame to check for leaks
from gas connections. Checking for leaks with a flame
may result in a fire or explosion.
Tighten all connections if necessary to prevent gas
leakage in the cooktop or supply line.
Check alignment of valves after connecting the
cooktop to the gas supply to be sure the cooktop
manifold pipe has not been moved.
Disconnect this cooktop and its individual shutoff
valve from the gas supply piping system during any
pressure testing of that system at test pressures greater
than ½ psig (3.5 kPa or 14" (35.6 cm) water column).
Isolate the cooktop from the gas supply piping
system by closing its individual manual shutoff valve
during any pressure testing of the gas supply piping
system at test pressures equal to or less than ½ psig
(3.5 kPa or 14" (35.6 cm) water column).
7. Connect Electricity to Gas
Cooktop
Electrical Requirements
120 volt, 60 Hertz, properly grounded branch circuit
protected by a 15 amp circuit breaker or time delay fuse.
Do not use an extension cord with this cooktop.
Preferred Method
Grounding
type wall
receptacle
Where a standard 2-prong wall receptacle is installed, it
is the personal responsibility and obligation of the
consumer to have it replaced by a properly grounded 3prong wall receptacle.
Do not, under any circumstances, cut or remove the
third (ground) prong from the power cord.
Do not, under any
circumstances, cut,
remove, or bypass
the grounding
prong.
Power supply cord with
3-prong grounding plug
Figure 10
Disconnect electrical supply cord from
wall receptacle before servicing cooktop.
8. Check Operation
Refer to the Use and Care Guide packaged with the
cooktop for operating instructions and for care and
cleaning of your cooktop.
Do not touch the burners. They may be hot enough to
cause burns.
1. Install Burner Caps
This cooktop is equipped with sealed burners as
shown (see Figure 11).
Burner Cap
Grounding Instructions
IMPORTANT Please read carefully.
For personal safety, this appliance must be properly
grounded.
The power cord of this appliance is equipped with a 3prong (grounding) plug which mates with a standard 3prong grounding wall receptacle (see Figure 8) to
minimize the possibility of electric shock hazard from the
appliance.
The wall receptacle and circuit should be checked by a
qualified electrician to make sure the receptacle is
properly grounded.
Burner Base
Burner Pan
(Built-in)
Gas Opening
Electrode
Figure 11
7
GAS COOKTOP INSTALLATION INSTRUCTIONS
(Models with Optional Electric Built-In Oven Combination)
A. Unpack burner bases and caps.
B. Place burner base over each gas opening tube.
C. Make sure the burner is properly aligned and
leveled. Place burner cap over each burner
base.
NOTE: There are no burner adjustments necessary on
this cooktop.
2. Turn on Electrical Power and Open Main Shutoff
Gas Valve
3. Check the Igniters
Operation of electric igniters should be checked after
cooktop and supply line connectors have been
carefully checked for leaks and the cooktop has
been connected to electric power.
To operate the surface burner:
A. Push in and turn a surface burner knob to the
LITE position. You will hear a little ticking noise;
this is the sound of the electric ignitor which
lights the burner.
B. After the burner lights, turn to the desired flame
size. The controls do not have to be set at a
particular mark. Use the marks as a guide and
adjust the flame as needed.
4. Adjust the "LO" or "SIMMER" Setting of Surface
Burner Valves (see Figure 12)
Push in and turn each control knob to the "LO" (or
"SIMMER") setting. The "LO" setting of each
burner has been set at the factory to the lowest
setting available to provide reliable reignition of the
burner. If it does not stay lit on the "LO" setting,
check the setting as follows.
A. Allow cooktop to cool to room temperature.
B. Light all burners by turning each control knob to
LITE until burners ignite, and then set them at
"HI".
C. Quickly turn the knob to the LOWEST POSITION.
D. If burner goes out, readjust valve as follows:
Remove the surface burner control knob, insert a
thin-bladed screw driver into the hollow valve
stem and engage the slotted screw inside.
Flame size can be increased or decreased with
the turn of the screw. Adjust flame until you
can quickly turn knob from HI to LOWEST
POSITION without extinguishing the flame.
Flame should be as small as possible without
going out.
E. If you need to adjust another burner, repeat the
steps from A to D above until all burners operate
properly.
When All Hookups are Complete
Make sure all controls are left in the OFF position.
Make sure the flow of combustion and ventilation air to
the cooktop is unobstructed.
Model and Serial Number Location
The serial plate is located on the underside of the
cooktop.
When ordering parts for or making inquires about your
range, always be sure to include the model and serial
numbers and a lot number or letter from the serial plate
of your cooktop.
Your serial plate also tells you the rating of the burners,
the type of fuel and the pressure the cooktop was
adjusted for when it left the factory.
Hollow Valve
System
Before You Call for Service
Read the Avoid Service Checklist and operating
instructions in your Use and Care Guide.
Check to make sure the house fuse or circuit breaker for
your cooktop are not blown or open.
Figure 12
8
INSTRUCCIONES DE INSTALACION PARA PLANCHA DE COCINAR A GAS
(Modelos con un horno eléctrico empotrado facultativo)
LA INSTALACIÓN Y EL SERVICIO DEBEN SER REALIZADOS POR UN
INSTALADOR CALIFICADO.
IMPORTANTE: GUARDE ESTAS INSTRUCCIONES PARA USO DEL
INSPECTOR ELÉCTRICO LOCAL.
LEA Y GUARDE ESTAS INSTRUCCIONES PARA FUTURAS REFERENCIAS
Si todas las instrucciones de éste manual no son observadas a la letra, se puede ocurrir
incendios o explosiones que pueden causar daños materiales, lesiones o la muerte.
PARA SU SEGURIDAD:
— No almacene o utilice gasolina u otros vapores y liquidos inflamables cerca de éste o cualquier otro
artefacto.
— QUE HACER SI HAY FUGAS DE GAS
• No intente de encender ningún artefacto
• No toque ningún interruptor eléctrico; no utilice ningún aparato téléfonico en su edificio.
• Llame inmediatamente el abastecedor de gas desde el teléfono de un vecino. Siga las instrucciones del
abastecedor de gas.
• En caso que no puede contactar el abastecedor de gas llame al departamento de bomberos.
— La instalación y el servicio téléfonico deben ser realizados por un instalador calificado, por un servicio
tecnico certificado o por el abastecedor de gas.
Dimensiones de la plancha de cocinar a gas
A
Dimensiones del hueco para la plancha de cocinar a gas
L
E
M
Figura 1
MODELO
30" Models 30 (76.2) 21 ½ (54.6) 3
36" X 21½" Models 3 6 (91.4) 21 ½ (54.6) 3
36"X 18" Models 36 (91.4) 18 (45.7) 3 ½ (8.9) 34 ¼ (87) 34
A.
ALTURAB.ANCHURA
C.
PROFUNDIDAD
1
/8 (7.9) 26 5/8 (67.6) 26 7/8 (68.3) 19 (48.3) 19 3/8 (49.2) 5 (12.7) 2¾ (7) 2¼ (5.7)
1
/8 (7.9) 32 ¾ (83.2) 33 (83.8) 19 (48.3) 19 3/8 (49.2) 5 (12.7) 2¾ (7) 2¼ (5.7)
MÍN. D. ALTURA MÁX.
DIMENSIONES DEL HUECO
* 30" mín. para un armario protegido.
24" mín. para una superficie no
protegida.
30" Mín.*
B
(76.2 cm) Mín.*
C
F
D
F.
PROFUNDIDAD
POR DEBAJO DE
MÍN. E. ANCHURA MÁX.
3
/8 (87.3) 16 5/8 (42.2) 16 ¾ (42.5) 5 (12.7) 4¼ (10.8) 3 (7.6)
LA PLANCHA DE
COCINAR
L
(MÍn.)M(MÍn.)
Todas las dimensiones se dan en pulgadas (cm).
La dimensión F esté por debajo de la plancha de cocinar para la conexión de la línea de suministro de gas.
NOTA: Se adjunta los diagramas de cables de esta plancha de cocinar con el libreta.
Solamente algunos modelos están disponibles en Canadá.
Papel reciclado
9
Diagrama de la instalación alámbrica - pages 27-28
P/N 318201450 (0410) Rev. B
English – pages 1-8
Español – pages 9-17
Français – pages 18-26
Loading...