Frigidaire EI24EC15KS, EI24EC15KS2, FEC30S6AB1, FEC36S6EB1, FEC36S6ES1 Installation Guide

...

Canada

INSTALLATION AND SERVICE MUST BE PERFORMED

BY A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. _FOR YOUR SAFETY: Do not store or use gasoline or other

flammable vapors and liquids in the vicinity of this or any other appliance.

IMPORTANT INSTALLATION-INFORMATION

, All electric cooktops run off a single phase, three-wire

or four-wire cable, 240/208 volt, 60 hertz, AC only electrical supply with ground.

, Pleasenote minimum distances between cooktop and

adjacent and overhead cabinetry is 30" (76.2cm).

Cooktop Cutout Dimensions

United States

* 30" (76.2 cm) min. for unprotected cabinet

24" (61 cm) min. for protected surface

Figure 1

24" CeramicGlass 24 (61.0) 213/8(54.4) 2% (6.7) 23 (58.5) 23¼(59.0) 20¼(51.4) 201/2(52.1) 5 (12.7)

26" CoilElements 253/4(65.4) 21%6(54.8) 31/2(8.9) 25 (63.5) 25(63.5) 20½(52.1) 201/2(52.1) 51/2(14)

30" CeramicGlass 303/8(77.8) 213/8(54.4) 2% (6.7) 29%(75.2) 29718(75.9) 20¼(51.4) 20½(52.1) 5(12.7)

30" Coil Elements 30 (76.2) 21112(54.6) 3 (7.6) 26314(67.9) 28¼ (71.8) 191/8(48.6) 20 (50.8) 5 (12.7)

32" Ceramic Glass 321/4(81.9) 201/4(51.4) 33/4(9.5) 31 (78.7) 311/4(79.4) 19 (48.3) 191/4(48.9) 53/4(14.6)

32" Coil Elements 321/4(81.9) 201/4(51.4) 33/4(9.5) 31 (78.7) 311/4(79.4) 19 (48.3) 191/4(48.9) 53/4(14.6)

36" Ceramic Glass 363/4(93.5) 213/8(54.4) 2% (6.7) 35% (90.5) 361/8(91.8) 201/4(51.4) 201/2(52.1) 5 (12.7)

36" Coil Elements

(36"X 18")

36(91.4) 18(45.7) 3718(9.8) 341/4(87) 34318(87.3) 16%(42.2) 163/4(42.5) 5718(14.9)

36" CoilElements

(36" x 211/2'')

36(91.4) 211/2(54.6) 3 (7.6) 323/4(83.2) 341/4(87) 19 (48.3) 20(50.8) 5(12.7)

All dimensions are in inches (cm). Only some models are available in Canada. * Allow 2" (5 cm) space below cooktop to clear the electric cable and allow for installation of the

junction box on the wall at the back of the cooktop.

Printed in China

P/N 318205403 (0904) Rev. C

English - pages 1-8

Espahol- pages 9-16

Fran_ais - pages 17-24

Overhead Cabinet Should Not Exceeda

Maximum Depth of 13" (33 cm)

30" (76.2cm) Min. Clearance _ [ --- //

Between the Top of the ' I I J Min.Recommended _ /I

Cooking Platform and the _ Distance Between Rear k_ / I

Bottom of an Unprotected _ I Edge of Cutoutand -"-___._------J

.... _ Nearest Combustible 10"

Wood or Metal Cabinet_,_ SurfaceAbove ( 25.4 cm)

24" (61 cm) Min. when

Bottom of Wood or Metal

Cabinet is Protected by

Not LessThan 1/8" Flame

Retardant Millboard Covered

With Not LessThan No. 28

MGS Sheet Steel, 0.015" (0.4

mm) Stainless Steel, 0.024"

(0.6 ram) Aluminum or

0.020" (0.5 mm) Copper 2 1/2" (6.4 cm)

Min. From Edge

of Cutout to Front

Edge of Countertop

Countertop

25" Min.

L_3 cm Min.)

N Min. From Edge of

Cooktop to Nearest

Combustible Wall (Either

Side of Unit).

Approximate Location of

Junction Box

* Letters on this figure refer to chart on

front page except for G, H and J.

To eliminate the risk of burns or

fire by reaching over heated surfaces, cabinet storage space located above the cooktop should

be avoided. If cabinet storage is provided, risk

can be reduced by installing a range hood that

projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

Figure 2 - COUNTERTOP CUTOUT OPENING

Important Notes to the Installer

1. Read all instructions contained in these installation instructions before installing the cooktop.

2. Remove all packing material before connecting the electrical supply to the cooktop.

3. Observe all governing codes and ordinances.

4. Be sure to leave these instructions with the consumer.

Fora drawer installation below the

cooktop, allow Dimension G of clearance

underneath the countertop. The drawer must not interfere with the electrical

12"

installation of the cooktop or contain

flammable materials.

(30.5 cm)

24" Ceramic-Glass 26" Coil Elements 30" Ceramic-Glass 30" Coil Elements 32" Ceramic-Glass 32" Coil Elements 36" Ceramic-Glass 36" Coil Elements

(36"X 18")

36" Coil Elements (36" X21½")

4" (I02 cm) 7V)" (191 cm) 3_/_"(89 cm) 3" (76 cm) 4" (I02 cm) 7V)" (191 cm) 6" (152 cm) 7V_" (19 1 cm) 4" (102 cm) 7V_" (191 cm) 6" (152 cm) 7V_" (19 1 cm) 4" (102 cm) 7VY' (191 cm) 6" (15.2 cm) 3" (7.6 cm)

6" (15.2 cm) 7_/2'' (19.1 cm)

2" (5I cm) 2" (5I cm) 2" (5I cm)

2//_" (57 cm)

2" (5I cm)

21/,_"(57 cm)

2" (5I cm) 3" (7.6 cm)

2_/_"(5.7cm)

Important Note to the Consumer Keep these instructions with your owner's guide for future

reference.

iMPORTANT SAFETY iNSTRUCTiONS

• Be sure your cooktop is installed and grounded

properly by a qualified installer or service technician,

• These cooktops must be electrically grounded in

accordance with local codes or, in their absence, with the National Electrical Code ANSI/NFPA No.

70--latest edition in the United States, or with CSA Standard C22.1, Canadian Electrical Code, Part

1, in Canada.

_The electrical power to the cooktop must be shut off while line connections are being

made. Failure to do so could result in serious injury or death,

Provide Electrical Connection

Install the junction box under the cabinet and run

120/240 or 120/208 Volt, AC wire from the main circuit

panel. DO NOT connect the wire to the circuit panel at this time.

2. The flexible armored cable extending from the appliance should be connected directly to the

junction box. The junction box should be located

as shown in Figure 1 or Figure 2 and with as much slack as possible remaining in the cable between

the box and the appliance, so it can be moved if

servicing is ever necessary.

3. A suitable strain relief must be provided to attach

the flexible armored cable to the junction box.

Unpacking Instructions (Models with Ceramic-Glass Smoothtop Only)

1. Leave corner supports on cooktop until completion of Electrical Connection.

2. Be sure the bottle of cleaner conditioner packed in the literature bag is left where the user can

find it easily. It is important that the ceramic-glass

smoothtop be pretreated before use.

Electrical Requirements

This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse. A circuit breaker or fuse is required by your appliance. The circuit breaker or fuse amperage recommended for your appliance is 40A or 50A,

Observe all governing codes and local ordinances

1.A 3-wire or 4-wire single phase 120/240 or 120/208 Volt, 60 Hz AC only electrical supply is required on a separate circuit fused on both sides of the line (red and black wires). A time-delay fuse or circuit breaker is recommended. DO NOT fuse neutral (white wire). Only certain cooktop models may be installed over certain built-in electric oven models. Approved cooktops and built-in ovens are listed by the MFG ID number (see the insert sheet included in the literature package).

NOTE: Wire sizes and connections must conform with the fuse size and rating of the appliance in accordance

with the American National Electrical Code ANSI/NFPA No. 70-latest edition, or with Canadian CSA Standard

C22.1, Canadian Electrical Code, Part 1, and local codes and ordinances.

An extension cord should not be used

with this appliance, Such use may result in a fire, electrical shock, or other personal injury.

Serial plate

(under cooktop)

Figure 3

Electrical Connection

It is the responsibility and obligation of the consumer to contact a qualified installer to assure that the electrical installation is adequate and is in conformance with the

National Electrical Code ANSI/NFPA No. 70-latest edition, or with CSA Standard C22.1, Canadian Electrical Code, Part 1, and local codes and ordinances.

Risk of electrical shock (Failure to

heed this warning may result in electrocution or other serious injury.) This appliance is equipped with copper lead wire. If connection is made to aluminum house wiring, use only connectors that are approved for joining copper and aluminum wire

in accordance with the National Electrical Code and local code and ordinances. When installing

connectors having screws which bear directly on the steel and/or aluminum flexible conduit, do no

tighten screws sufficiently to damage the flexible conduit, Do not over bend or excessively distort flexible conduit to avoid separation of convolutions en exposure of internal wires.

Electrical ground is required on this appliance,

Thisapplianceismanufacturedwithaframeconnected green(orbarecopper)groundwire.

DONOTgroundto a gassupplypipe. DONOTconnectto electricalpowersupplyuntil applianceispermanentlygrounded.Connectthe groundwire beforeturningonthe power.

If__yourappliance is not equipped with a white

neutral conductor: Connect only to a 3-wire, 120/240V power supply; the

neutral conductor is not required for the operation of the appliance. The potential at the power supply electrical connections shall be 150V to ground or less.

Where local codes permit connecting the appliance-grounding conductor to the neutral

(white) wire (USA only): Your appliance has a 3-wire cable to be connected

to a 3-wire grounded junction box (see figure 4):

1. Disconnect the power supply.

2. In the circuit breaker, fuse box or junction box: Connect appliance and power supply cable wires as shown in figure 4.

Cablefrom PowerSupply

Ground Wire

NOTE TO ELECTRICIAN: The armored cable leads supplied with the appliance are UL-recognized for

connection to larger gauge household wiring. The insulation of the leads is rated at temperatures much higher than temperature rating of household wiring. The current carrying capacity of the conductor is governed by the temperature rating of the insulation around the wire, rather than the wire gauge alone.

RISK OF ELECTRICSHOCK: Grounding through the neutral conductor is prohibited for new branch-circuit

installations (1996 NEC); mobile homes; recreational vehicules; or in Canada, or in an area where local codes

prohibit grounding through the neutral connector.

(If your appliance is equipped with a white neutral conductor,) This appliance is manufactured with a white neutral

power supply and a frame connected copper wire, The frame is grounded by connection of grounding lead to neutral lead at the termination

of the conduit, if used in USA, in a new branch circuit installation (1996 NEC), mobile home,

recreational vehicles, where local code do not permit grounding trough the neutral (white) wire

or in Canada, disconnect the white and green lead from each other and use ground lead to ground

unit in accordance with local codes, connect neutral lead to branch circuit-neutral conductor in usual

manner see Figure 6 or 7. If your appliance is to be connected to a 3 wire grounded junction box (US only), where local code permit connecting the appliance-grounding conductor to the neutral (white) see Figure 4 or 5.

Red

Wires

Ground Wire (Bareor

GreenWire)

Cablefrom appliance

Figure 4 - U.S.A. Only

3-WIRE GROUNDED JUNCTION BOX

Your appliance has a 4-wire cable to be connected to a 3-wire grounded junction box (see figure 5):

1. Disconnect the power supply.

2. In the junction box: Connect appliance and power supply cable wires as shown in Figure 5.

CablefromPowerSupply

GroundWire

RedWires_ ''_ -,_-_I _................

GroundWire J _:&:_d (BareorGreenWire)

Cablefromappliance

Figure 5 - U.S.A. Only

3-WIRE GROUNDED JUNCTION BOX

U.L.-ListedConduit

Connector(or CSA

listed)

/_ Black

_ires 1

, I_---- Junction "-t_ Box

,--'J WhiteWire

""U.L-Listed Conduit

Connector(orCSAlisted)

Black Wires

Box

if the appliance is used in a new branch circuit installation (1996 NEC), mobile home, recreational vehicle, or where local codes DO

NOT permit grounding through the neutraJ (white) wire, the appliance frame MUST NOT

be connected to the neutral wire of the 4-wire electrical system.

Your appliance has a 3-wire cabJe to be connected to a 4-wire grounded junction box (see figure 6):

1. Disconnect the power supply.

2. Separate the green (or bare copper) and white appliance cable wires.

3. Cap the white wire from the power supply cable if a 3-wire appliance cable is supplied.

4. In the circuit breaker, fuse box or junction box: Connect appliance and power supply cable wires as

shown in figure 6.

Your appliance has a 4-wire cable to be connected to a 4-wire grounded junction box (see figure 7):

1. Disconnect the power supply.

2. In the junction box: Connect appliance and power supply cable wires as shown in Figure 7.

CablefromPowerSupply

Ground

Wire

Red

GroundWire (Bareor

GreenWire)

Wires

Black

Cablefrom PowerSupply

GroundWire

Red

Wires

Ground Wire (Bareor

GreenWire)

Cablefrom appliance

Figure 6

4-WIRE GROUNDED JUNCTION BOX

Wire

Black

Wires

Box

U.L.-Listed

Conduit Connector(or

CSAlisted)

JunctionBox _......

Cablefromappliance

Figure 7

4-WIRE GROUNDED JUNCTION BOX

U.L.-ListedConduit Connector(orCSAlisted)

Cooktop Installation

1. All Ceramic-GlassCooktops

Visuallyinspectthecooktopfordamage.Alsomakesure

allcooktopscrewsaretight(seeFigure8).

TheretainerbracketsMUSTbeinstalled,to meet localcodesor,intheir absence,with the National ElectricalCodeANSI/NFPANo.70--latestedition,or with CSAStandardC22.1,CanadianElectricalCode,

PartI (seeFigure10).

Screws

Figure8

Setthecooktopintothecountertopcutout. NOTE:Donotusecaulkingcompound;cooktopshould

beremovableforservicewhenneeded.

Donot removethe built in springson

theedgesof thecooktop.Thesespringscenterthe cooktopin the spaceprovided.Thecooktopmust becenteredto preventexcessheatbuildupthat mayresultinheatdamageorfire (seeFigure9).

Cooktop,_ Countertop

Built in

Spring

Retainer Bracket

Figure 10

2. Models: 26" and 36" (36" X 18") Coil Elements Cooktops

Set the cooktop into the countertop cutout. Lift the cooktop and fasten the ends of the box to the counter with wood screws (figure 11). Lower the cooktop. Align the knobs on the shafts and press down with even

pressure.

Retainer Brackets Must

T Be Installed At Least

1/16" (0.16 cm)

BELOW Countertop

8 :\..

Springs _, . .-

. ,---" - " Position bracketson

2 Retainer_1_.,,. . - unit cutout center

Brackets " ".....

Figure 9

line (CL)

Figure 11

3. Models:32"CoilElementsCooktops

1.Placecooktopintocountertopopeningandcenter unitincutout.

2.Removeallsurfaceunitsanddripbowls.

3.Unitclampclowninformation.Onceunitisinstalledin counteropening,youmustclampunitdownasshown

infigure12.

4.Putbackallsurfaceunitsanddripbowls.

5.Makeelectricalconnectionsasoutlinedin "Electrical Connection"section.

Reachdownthroughsurfaceunitopeningsandinstall

thefourholddownretainerswithscrewsasshown.Be certaincookingtopisfirmlyretainedtocountertop.

Cooktop spacer

Holddown retainer

Burner box

Figure 12

Countertop

4. Prior to tightening installation screws, exert downward pressure on burner box to assure flanges on burner box rest firmly on counter. Tighten all screws evenly.

5. Unit clamp down information. Once unit is installed in

counter opening, you must clamp unit down as shown

in figure 14.

6. Make electrical connections as outlined in "Electrical

Connection" Section.

Toclamp down, insert bracket with offset side of angle into slot on each side of unit. The screw should then be run through bracket and against bottom of counter. Tighten until draws down.

Cooktop_ _ C°unter_l r

Holddown retainer _,__ Screw

Burner box

Figure 14

4. Models: 30" and 36" (36" X 211/2") Coil Elements Cooktops

- These cooktops are designed to fit various cutout sizes.

The minimum and maximum cutout openings are

shown in figure 1.

- If cooktop isto be used in new installation, use

minimum cutout dimensions in figure 1.

- Attach cooktop to cabinet using wood screws through

holes in vertical walls of burner box.

- If cooktop is to be installed as a replacement in

an existing countertop opening (not exceeding maximum cutout dimensions as shown in figure

1), the following steps must be taken:

1. Insert 4 screws and installation spacers through holes in vertical walls of burner box (see figure 13).

2. Place cooktop into countertop opening and center unit in cutout.

3. Tighten each screw finger tight or until spacers are

snug against burner box walls.

Spacer

Screw

Checking Operation Refer to the Owner's Guide for operation.

Do not touch cooktop glass or elements.

They may be hot enough to burn.

Model and Serial Number Location The serial plate is located under the cooktop or in the

burner box and can be seen by lifting up the main top of unit.

When ordering parts for or making inquires about your cooktop, always be sure to include the model and serial numbers and a lot number or letter from the serial plate on your cooktop.

Before You Call for Service Read the Avoid Service Checklist and operating

instructions in your Owner's Guide. It may save you time and expense. The list includes common occurrences that are not the result of defective workmanship or materials in this appliance.

Refer to the warranty in your Owner's Guide for our service phone number and address. Pleasecall or write if you have inquiries about your product and/or need to order parts.

Figure 13

Fortypicalundercounterinstallationofanelectricbuilt-inovenseeFigurebelow.

Onlycertaincooktopmodelsmaybeinstalled overcertainbuilt-inelectricovenmodels.

Approvedcooktopsandbuilt-inovensarelisted bytheMFGIDnumberandproductcode(seethe insertsheetincludedintheliteraturepackagea[ cooktopinstallationinstructionsfordimensions

Toreducetheriskof personalinjuryand

Approx.3"

(7.5cm)

tippingof thewall oven,thewalloven mustbesecuredto

thecabinet(s)by mountingbrackets,

208/240Voltjunctionbox

forbuilt-in

Note1 4" x4" (10.2cmX 10.2cm)openingto routearmoredcablefromcooktoptojunction

box.

Approx.3" 208/240Volt

(7.5cm) junctionbox

forcooktop

Note1

Cabinetsidefillerpanels arenecessaryto isolate

theunitfromadjoining

cabinets.Cabinetside

fillerheightshouldallow forinstallationofap-

provedcooktopmodels

36"Min. (91.4cm)Min.

Cutanopeninginwoodbaseminimum4" x4" (10.2X10.2cm),2" (5cm)fromleftsidefiller

panel,toroutearmouredcabletojunctionbox.

* Ifnocooktopisinstalleddirectly

overtheovenunit,5" (12.7cm) maximumisallowedabovethe

floor.

TYPICAL UNDER COUNTER INSTALLATION OF A SINGLE ELECTRICBUILT-IN OVEN

WITH AN ELECTRIC COOKTOP MOUNTED ABOVE

27" (68.6cm) 247W' (63.2cm) Min. 23V2" (59.7cm) Min. 27¼" (69.2cm) Min.

Wall Oven 25¼" (64.1cm) Max. 28¼" (71.Scm) Max.

30" (76.2cm) 28_/2'' (72.4cm) Min. 27¼" (69.2cm) Min.

Wall Oven 29" (73.7cm) Max. 23V2" (59.7cm) Min. 28¼" (71.Scm) Max.

Use3/4"(1.gcm)plywood, installedontworunners, flushwithtoeplate.

Basemustbecapableof

Unitwill overlapcutot

(minimum)

edgesby1"

supporting150pounds (68kg)for27" modelsand

200pounds(90kg)for30" models.

(2.5cm) 41/2" (11.5cm)

Max.*

CUTOUT DIMENSIONS

I F. WIDTH. GI DEPTH I H: HEIGHT

+ 16 hidden pages