Frigidaire FFBD1821MB0A, FFBD1821MB1B, FFBD1821MS0A, FFBD1821MS1B, FFBD1821MW0A Installation Guide

...

Installation

Built-In

Instructions

Dishwasher

If you have questions, call 800-944-9400(US), 800-245-8352 (Canada) or visit our website at: www.Frigidaire.com

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

IMPORTANT --Observe all

governing codes and ordinances.

• Note to Installer - Be sure to leave these instructions for the consumer's and local

inspector's use.

• Note to Consumer - Keep these instructions with your Owner's Manual for future reference.

• Skill Level - Installation of this dishwasher requires basic mechanical and electrical skills.

Proper installation is the responsibility of the installer. Product failure due to improper

installation is not covered under the ELECTROLUX Appliance Warranty.

• Completion Time - 1 to 3 Hours. New installations require more time than replacement

installations.

IMPORTANT - The dishwasher

MUST be installed to allow for future removal from

the enclosure if service is required.

If you received a damaged dishwasher, you should immediately contact your dealer or builder.

Optional Accessories - See the Owner's Manual

for available custom panel kits.

FOR YOUR SAFETY

Read and observe all CAUTIONS and WARNINGS shown throughout these instructions. While

performing installations described in this booklet, gloves, safety glasses or goggles should be

worn.

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

To reduce the risk of electrical shock, fire, or injury to persons, the installer must

WARNING

ensure that the dishwasher is completely enclosed at the time of installation.

Installation Preparation

PARTS SUPPLIED:

Two #8 Phillips flat head wood screws, 5/8" long to secure dishwasher to underside of countertop (in literature package).

Two Phillips head, color matched toekick screws (in literature package).

MATERIALS YOU WILL NEED:

Ferrule, compression nut and 90° Elbow (3/ 8"NPT external thread on one end, opposite end sized to fit water supply)

Thread seal tape UL Listed wire nuts (3)

Materials for New Installations Only:

Air gap for drain hose, if required Waste tee for house plumbing, if applicable Electrical cable or power cord, if applicable Screw type hose clamps

Strain relief for electrical connection Hand shut-off valve

Water line 3/8" min. copper Coupler for extending drain line, if applicable

2 Wood Screws

90° Elbow, Ferrule and

Compression Nut

Waste Tee

Air Gap

2 Color Matched

Toekick Screws

Hand

Shut-Off Thread Valve Seal

Electrical Cable (or Power Cord, if

applicable)

Screw Type Hose

Clamps

Screw Type

Hose Clamp

Wire Nuts (3)

Tape

Hot Water line

Coupler

Strain Relief

TOOLS YOU WILL NEED:

Phillips head screwdriver 5/16" and 1/4" nutdriver

6" Adjustable wrench Level

Carpenters square Measuring tape Safety glasses Flashlight Bucket to catch water when flushing

the line Gloves

For New Installations Only:

Tubing cutter Drill and appropriate bits

Hole saw set

Phi

Head

Screwdriver

Flashlight

Gloves

Bucket

1/4"

and 5/16" Nutdriver

Level

6"diusta ,e

nch

Safety Glasses

Hole Saw Set

Cutter Tubing

Carpenters Square

I;,;,;,;,;,;,;,;,;,;,;,:,

Measuring Tape

Installation Preparation

PREPAREDISHWASHERENCLOSURE

32.5"

Undersideof

C0untert0p

toFloor

•Square

17-5/8"Min.

18"Max.

Figure A

• The rough cabinet opening must be at least 24" deep and 17-5/8" to 18" wide. The opening should be 32.5" max. height.

Plumbing andElectricService

Must EnterShadedArea

and

Plumb

DRAIN REQUIREMENTS

° Follow local codes and ordinances. ° Do not exceed 10 feet distance to drain. ° Do not connect drain lines from other devices to the

dishwasher drain hose.

° Dishwasher must be connected to waste line with an

air gap (not supplied) or 32" minimum high drain loop, depending on local codes and ordinances to

prevent back flow into the dishwasher.

° Air gap must be used if waste tee or disposer

connection is less than 18" above the floor to prevent siphoning.

DRAIN PREPARATION The type of drain installation depends on answers to

the following questions:

Do local codes or ordinances require an air gap? Will waste tee or disposer connection be less than

18" above the floor?

Will installation have a drain loop less than 32" above floor?

If the answer to ANY of the 3 questions above is YES, Method 1 MUST be used. Otherwise either Method 1 or

Method 2 may be used. Figure C or Figure D.

CAUTION:

An air gap MUST BE USED if the drain hose is connected to waste tee or disposer lower than 18"

above the floor. Failure to provide the proper drain connection height

with air gap or 32" minimum, high drain loop will result in improper draining of the dishwasher.

• The dishwasher must be installed so that drain hose is no more than 10 feet in length for proper drainage.

• The dishwasher must be fully enclosed on the top, sides and back, and must not support any part of the

enclosure.

CLEARANCES: When installed into a corner,

allow 2" min. clearance between dishwasher

and adjacent cabinet, wall or other appliances.

Allow 25-5/8" min.

clearance from the front of the dishwasher for

door opening. Figure B

Note: ADA installation, (32-1/2") beneath 34" high counter-tops may be accomplished by adjusting the

toekick and leveling legs.

Method 1 - Air Gap with Waste Tee or Disposer

__'___ ra __a_ ra

Figure C

Method 2 - High Drain with Waste Tee or Disposer Provide a method to attach drain hose to underside of

countertop.

,, 32" 18"

vin _l_J_/

Figure D

Install waste tee or disposer and air gap according to manufacturer's instructions.

CABINET PREPARATION

° Drill a 1-1/2" dia. hole in the cabinet wall within the

shaded areas shown in Figure A for the drain hose connection. The hole should be smooth with no sharp edges.

JJC0untert0p

Dishwasher

25-5/8"

_ Clearancefor Door _/ 0pening2 Minimum

Figure B

--r"-ql_

in.

Installation Preparation

PREPARE ELECTRICAL WIRING

WARNING

FOR PERSONAL SAFETY: Remove house fuse or open circuit breaker

before beginning installation. Do not use an extension cord or adapter plug

with this appliance.

Electrical Requirements

• This appliance must be supplied with 120V, 60 Hz., and connected to an individual properly grounded branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse.

• Wiring must be 2 wire with ground.

° If the electrical supply does not meet the above

requirements, call a licensed electrician before proceeding.

Grounding Instructions - Cable Direct

This appliance must be connected to a grounded metal, permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and be connected to the equipment grounding terminal or lead

on the appliance.

Grounding Instructions - Power Cord Models

his appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electrical shock by providing a path of least resistance for electric current. The plug must be plugged into an appropriate outlet that is installed and grounded in

accordance with local codes and ordinances.

WARNING

The improper connection of the equipment grounding conductor can

result in a risk of electric shock. Check with a qualified electrician or

service representative if you are in doubt that the appliance is properly grounded.

/ I I \

I I

1-1/2"Dia.

Hole(Max.)

from

Cabinet

Figure E White

Cabinet Preparation & Wire Routing

• The wiring may enter the opening from either side, rear or the floor within the shaded area.

• Cut a 1-1/2" max. dia. hole to admit the electrical cable. The hole must be free of sharp edges. Ifthe

cabinet wall is metal, the hole edge must be covered with a bushing.

• Cable direct connections may pass through the same hole as the drain hose and hot water line, if convenient. If cabinet wall is metal, the hole edge must be covered with a bushing. NOTE: Power cords with plug must pass through a separate hole.

Electrical Connection to Dishwasher Electrical connection is on the right front of dishwasher.

• For cable direct connections the cable must be routed as shown in Figure E. Cable must extend a minimum of

24" from the rear wall.

• For power cord connections, install a 3-prong grounding type receptacle. The power-supply receptacle for the appliance shall be installed in a cabinet or on a wall adjacent to the undercounter space in which the appliance is to be installed.

+ 8 hidden pages