Frigidaire DGHF2360PF1, DGHF2360PF2A, DGHF2360PF3A, DGHF2360PF4A, DGHF2360PF5A Installation Guide

...

Frigidaire DGHF2360PF1, DGHF2360PF2A, DGHF2360PF3A, DGHF2360PF4A, DGHF2360PF5A, DGHF2360PF6A, DGHF2360PF7A, DGHF2360PF8A, DGHF2360PF9A, FDBC2250SS0, FDBG2250SS0, FDBN2750SS2, FDBN2750SS3, FDBN2750SS4, FDBS2750SS0, FDBS2750SS1, FFHB2740PE1, FFHB2740PE2, FFHB2740PE3, FFHB2740PE4, FFHB2740PE5A, FFHB2740PE6A, FFHB2740PE7A, FFHB2740PE9A, FFHB2740PEAA, FFHB2740PEBA, FFHB2740PECA, FFHB2740PEDA, FFHB2740PP0, FFHB2740PP1, FFHB2740PP2, FFHB2740PP3, FFHB2740PP4, FFHB2740PP5A, FFHB2740PP6A, FFHB2740PP7A, FFHB2740PP9A, FFHB2740PPAA, FFHB2740PPBA, FFHB2740PPCA, FFHB2740PPDA, FFHB2740PS0, FFHB2740PS1, FFHB2740PS2, FFHB2740PS3, FFHB2740PS4, FFHB2740PS5, FFHB2740PS6A, FFHB2740PS7A, FFHB2740PS8A, FFHB2740PSAA, FFHB2740PSBA, FFHB2740PSCA, FFHB2740PSDA, FFHB2740PSEA, FFHN2740PE0, FFHN2740PE1, FFHN2740PE2A, FFHN2740PE3A, FFHN2740PE4A, FFHN2740PE5A, FFHN2740PE6A, FFHN2740PE8A, FFHN2740PE9A, FFHN2740PEAA, FFHN2740PECA, FFHN2740PP0, FFHN2740PP1, FFHN2740PP2A, FFHN2740PP3A, FFHN2740PP4A, FFHN2740PP5A, FFHN2740PP6A, FFHN2740PP8A, FFHN2740PP9A, FFHN2740PPAA, FFHN2740PPCA, FFHN2740PS0, FFHN2740PS1, FFHN2740PS2A, FFHN2740PS3A, FFHN2740PS4A, FFHN2740PS5A, FFHN2740PS6A, FFHN2740PS8A, FFHN2740PS9A, FFHN2740PSAA, FFHN2740PSCA, FGEB28D7RF0, FGEB28D7RF2, FGHB2735NE0, FGHB2735NE2, FGHB2735NE3, FGHB2735NF2, FGHB2735NF3, FGHB2735NP2, FGHB2735NP3, FGHB2866PE3, FGHB2866PE4, FGHB2866PE5A, FGHB2866PE6A, FGHB2866PE7A, FGHB2866PE9A, FGHB2866PEAA, FGHB2866PEBA, FGHB2866PECA, FGHB2866PEDA, FGHB2866PEEA, FGHB2866PF3, FGHB2866PF4, FGHB2866PF6, FGHB2866PF7A, FGHB2866PF9A, FGHB2866PFAA, FGHB2866PFBA, FGHB2866PFCA, FGHB2866PFDA, FGHB2866PFEA, FGHB2866PFFA, FGHB2866PFGA, FGHB2866PFJA, FGHB2866PFLA, FGHB2866PFMA, FGHB2866PP3, FGHB2866PP4, FGHB2866PP5A, FGHB2866PP6A, FGHB2866PP7A, FGHB2866PP9A, FGHB2866PPAA, FGHB2866PPBA, FGHB2866PPCA, FGHB2866PPDA, FGHB2866PPEA, FGHB2866PPFA, FGHF2366PF3, FGHF2366PF5A, FGHF2366PF6A, FGHF2366PF7A, FGHF2366PF8A, FGHF2366PF9A, FGHF2366PFAA, FGHF2366PFBA, FGHF2366PFDA, FGHG2366PF0, FGHG2366PF1A, FGHG2366PF2A, FGHG2366PF3A, FGHG2366PF4A, FGHG2366PF6A, FGHG2366PFAA, FGHN2866PE0, FGHN2866PE3A, FGHN2866PE6A, FGHN2866PE7A, FGHN2866PEAA, FGHN2866PF0, FGHN2866PF1, FGHN2866PF2, FGHN2866PF4A, FGHN2866PF5A, FGHN2866PF6A, FGHN2866PF7A, FGHN2866PF8A, FGHN2866PFBA, FGHN2866PFEA, FGHN2866PFFA, FGHN2866PFGA, FGHN2866PP0, FGHN2866PP1, FGHN2866PP2, FGHN2866PP3A, FGHN2866PP6A, FGHN2866PP7A, FGHN2866PPAA, FPBC2277RF0, FPBC2277RF1, FPBC2277RF2, FPBC2277RF3, FPBC2277RF4, FPBC2277RF5, FPBC2277RF7, FPBC2277RF8, FPBC2277RF9, FPBC2277RFA, FPBG2277RF0, FPBG2277RF1, FPBG2277RF4, FPBG2277RF5, FPBS2777RF0, FPBS2777RF1, FPBS2777RF2, FPBS2777RF3, FPBS2777RF4, FPBS2777RF6, FPBS2777RF9, FPBS2777RFA, FPBS2777RFB, FPBS2777RFC, FPHB2899PF1, FPHB2899PF2, FPHB2899PF3, FPHB2899PF4, FPHB2899PF5, FPHB2899PF6A, FPHB2899PF7A, FPHB2899PF8A, FPHF2399PF4, FPHF2399PF5, FPHF2399PF6, FPHF2399PF7A, FPHG2399PF0, FPHG2399PF2A, LFHB2741PF1, LFHB2741PF2, LFHB2741PF3, LFHB2741PF4, LFHB2741PF5A, LFHB2741PF6A, LFHB2741PF7A, LFHB2741PF8A, LFHB2741PF9A, LFHB2741PFAA, LFHB2741PFBA, LFHB2741PFDA, LGHB2867PF3, LGHB2867PF4, LGHB2867PF5, LGHB2867PF6A, LGHB2867PF7A, LGHB2867PF8A, LGHB2867PFAA, LGHB2867PFBA, LGHB2867PFCA, LGHB2867PFDA, LGHB2867PFEA, LGHB2867PFGA, LGHB2867PFHA, LGHB2867PFJA Installation Guide

0 (0)

FRIGID®IRE®

Installation Instructions* for French Door Bottom Freezer/Refrigerator

*Please refer to your Use & Care Guide for more details.

To Connect Water Supply Line To Ice Maker Inlet Valve

1. Disconnect refrigerator from electric power source.

To avoid electric shock, which can cause death or severe personal

injury, do not connect your refrigerator to an electrical power source

.......untily°uhavec°mpletedStep2°ftheseinstructi°ns"

If you needto removethe doors to get your refrigerator into the house, pleasereferto"Removing Doors"

in..tt_,use & CareGuide.TheseJns_llationinstru_ons are providedon_ as a pgssiblecus-_mer9_on.

Fng oa re ..........

• Shifting the refrigerator from side to side

may damage flooring.

Ifyou are installing your refrigerator ,,

without coonecting _tto a water

supply, make sure the ice maker's

power switcn is turned Off (see the • Do not block the toe grille on the lower

use & Care Guide ror more details), front of your refrigerator, Sufficient air cir-

culation msessent.al for proper operation.

Pro arin For Installation

Be sure to coordinate and installation

. site preparation

with your kitcnen contractor.

Include these minimum guidelines in your site preparation:

, Choose a place near a grounded electrical outlet.

, Do not use an extension cord or an adapter plug.

, Aygid direct sunlight and close proximity to a range, Please call 1-800-944-9044 if you

aisnwasner or otSer neat source, neea assistance with this installation.

, Floor should be level and able to support a fully ....................................................................................

ioaaea refrigerator. I

, The refrigerator's Ice Dispenser I

requires water supply access. I

o Plan for easy.accessto counter tops I

wnen remowng Tooa.

For complete access to drawers and I Room temperatures

below 55°F (13°C)

Treezer oasKets, aoors must be able to I

fully open. [ or above 110°F

Load refrigerator from side of cabinet

(43°C) will impair

only. cooling ability of

your refrigerator's

Do not run retaining straps over handles nor overtJghten straps, corn pressor.

• Never use refrigerator handles to move the refrigerator.

Allow the following clearances for ease of installation, proper air

drculation, and plumbing and electrical connections: Sides & Top: 3/8 inch / Rear: 1 inch

Connect Water Su I

To avoid electric shock,

which can cause death

Before Installing The Water Supply Line, You Will Need:

, Basic Tools: adjustable wrench, fiat-blade screwdriver, and

Phillips screwdriver

, Access to a household cold water line with water pressure

between 30 and 100 psi.

, A water supply line made of 1/4 inch (6 mm) OD, copper

or stainless steel tubing. To aetermine the _ength or

tub!ng needed z measurethe distance from the ice or severe personal

maker inlet vawe at the oacK of the reTrigerator to your injury, disconnect the

c_d water pipe. Then add approximately 7 feet, so the refricjerator from elec-

trical power before con-

refrigerator can oe movea outfor cleaning, necting a water supply

A shutoff valve to connect the water supply line to your line to the refrigerator.

household water system. DO NOT use a self-piercing type

shutoff valve.

, A compression nut and ferrule (sleeve) for connecting a copper water supply line to the

ice maker in_et valve.

To Avoid Property Damage:

• Copper or Stainless Steel braided tubing is recommended for the wa-

te_s'upply line. Water supply tubinq made of 1/4 inch (6 mm) plastic

is notrecommended to beused. Pla-stic tubing greatlY/ incre-ases the

potential for water leaks, and the manufacturer will not be respon-

sible for any damage if plastic tubing is used for the supply line.

• Do not reuse compression fitting or use thread seal tape.

• DO NOT install water supply tubing in areas where temperatures fall

below freezing.

• Chemicals from a malfunctioning softener can damage the ice maker.

If the ice maker is connected to soft water, ensure that the softener

is maintained and working properly.

2. Place end of water supply line into sink or

bucket. Turn ON water supply and flush

supply line until water is clear. Turn OFF

water supply at shutoff valve.

3. Remove plastic cap from water valve inlet

and discard cap.

4. If you use copper tubing - Slide brass

compression nut, then ferrule (sleeve) onto

water supply line. Push water supply line into

water valve inlet as far as it will go (1/4 inch).

Slide ferrule (sleeve) into valve inlet and

finger tighten compression nut onto valve.

Tighten another half turn with a wrench, DO

NOT overtJghten. See Figure 1.

If you use stainless steel tubing - The nut

and ferrule are already assembled on the

tubing. Slide compression nut onto valve

inlet and finger tighten compression nut

onto valve. Tighten another half turn with a

wrench; DO NOT overtJghten. See Figure 2.

5. With steel clamp and screw, secure water

supply line (copper tubing only) to rear panel

of refrigerator as shown.

6. Coil excess water supply line (copper tubing

only), about 2t/2 turns, behind refrigerator

as shown and arrange coils so they do not

vibrate or wear against any other surface.

7. Turn ON water supply at shutoff valve and

tighten any connections that leak.

8. Reconnect refrigerator to electrical power

source.

9. To turn ice maker on, lower wire signal arm

(freezer ice maker) or set the ice maker's On/

Off power switch to the "ON" position (fresh

food ice maker).

Check with your local building authority for

recommendations on water lines and associated

materials prior to installing your new refrigerator.

Depending on your local/state building

codes, Frigidaire recommends for homes with

existing valves its Smart Choice ®water line kit

5305513409 (with a 6 ft. Stainless Steel Water

Line) and for homes without an existing valve,

Frigidaire recommends its Smart Choice® water

line kit 5305510264 (with a 20 ft. Copper Water

Line with self-tapping saddle valve). Pleaserefer

to www.ffigidaire.com for more information.

Plastic Water

_ Steel

Clamp

Brass

Compression

.----'------ Nut

_ Ferrule

(Sleeve)

_'_-- copper

water line

ter Valve

Bracket

\-- valve ,nle;

¸line¸

water supp!y

(Include enough tubing in loop to allow

mo¥ing refdgerator out for cleaning.)

Figure 1

Level Refri erator

Guidelines for final positioning of your refrigerator

= All four cornersof the cabinetmust restfirmly on the

floor.

The sides should tilt tA inch (6 mm) from front to

back(to ensurethat doors closeand seal properly),

Doorsshouldalign with eachotherand be level

Host of these conditions can be met by raising or

lowering the adjustable front rollers,

To level the cabinet using the front rollers:

1 You can raise or lower each door. Use a 3/s inch socket

wrench to turn the adjustment screws (1 per side).

To raise: turn adjustment screw clockwise.

To lower: turn adjustment screw counterclockwise.

2 Ensure both doors are bind-free with their seals

touching the cabinet on all four sides and that cabinet

is stable.

3 After unit is leveled, lower anti-tip leg until it contacts

the floor.

Rai_

DO NOT REMOVE this label until the refrigerator has been leveled.

Please follow all instructions for leveling your refrigerator.

_q, Installin & Levelin Freezer Drawer if necessar

1. Installing freezer drawer: Refer to "Installing Freezer Drawer" in the Use & Care Guide.

2. Leveling freezer drawer:

A. Check gasket seal around top, bottom,

and sides of freezer drawer.

B. If gasket is not sealed, open drawer

and slightly loosen 4 drawer screws

(2 on each side) to allow drawer to

rotate.

C. Close drawer and recheck the seal

on the gasket (A). Open the drawer

grabbing by the sides in the center

(B). Be careful not to rotate the

drawer.

D. Tighten 4 drawer screws.

E. Recheck gasket seal.

F. Install the toe grille by fitting

into place.

iiFro_ilB0th!i;Sli

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Installin & Ad'ustin Doors if necessa

1. Installing doors: Refer to "Installing

Doors" in the Use & Care Guide.

2. Doors final adjustment using the

adjustable lower hinge (select

models, if necessary):

Open doors to 90 degrees.

Uft the door while adjusting

the washer.

To raise the door: rotate

washer clockwise.

To lower the door: rotate

washer counterclockwise.

Bottomof Door

Opening Door Raising/Lowering Door

Remove InternaIShi in Materials

Frigidaire uses packing foam and tape to secure the internal parts of your refrigerator for

shipping. Once the refrigerator is in position, you can remove this material.

What's Next?

Congratulations! You are ready to begin enjoying your new Frigidaire refrigerator.

For important safety instructions and to learn how to operate your refrigerator, please read

the entire Use & Care Guide.

You may want to start with the "Normal Operating Sights & Sounds" section of the Guide to

learn what to expect during typical operation.

Please register your product. You can register online at www.ffigidaire.com or you can

simply send in the Registration Card.

[] Installation Check List

D=e_s

[] Handles are secure and tight [] House water supply connected to

[] Door seals completely to cabinet on all sides refrigerator

[] Fresh food doors are level [] No water leaks present at all connections

[] Ice Maker is turned ON.

[] Refrigerator is level, side to side and tilted

tA inch (6 ram) front to back

[] Toe grille is properly attached to refrigerator [] Shipping material removed

[] Cabinet is sitting solid on all corners [] Fresh Food and Freezer temperatures set

[] House power turned on

[] Refrigerator plugged in

If you are not satisfied with the installation of your refrigerator, please contact the store where you purchased it or call 1-800-944-9044 for assistance. P/N: