Frigidaire EI30SM35QSA, CFMV152CLBA, CFMV152CLWA, CFMV152KBA, CFMV152KMA Installation Guide

...

Installation

Overthe Range

Instructions

Questions? Carl 1-800-944-9044(us)

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT - Savethese

instructions for local inspector's use.

• IMPORTANT - Observoall

governing codes and ordinances.

• Note to Installer - Be sure to leave these

instructions with the Consumer.

1-800-265-8352(Canada)

Microwave Oven

or Visit our Website at: http://www.frigidaire.com

• Note to Consumer - Keep these

instructions for future reference.

• Skill level - Installation of this appliance requires basic mechanical and electrical skills.

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not

covered under the Warranty.

READ CAREFU LLY.

KEEP THESE INSTRUCTIONS.

pin 316495063

March 2010

Installation Instructions

CONTENTS

General information

Important Safety Instructions .................................. 3

Electrical Requirements .......................................... 3

Damage - Shipment/Installation .............................. 4

Parts Included .......................................................... 4

Tools You Will Need ................................................ 5

Mounting Space ...................................................... 5

Step-by-step installation guide

Placement of The Mounting Plate ...................... 6-8

Removing the Mounting Plate ...................... 6

Finding the Wall Studs .................................. 6

Determining Wall Plate Location .................. 7

Aligning the Wall Plate ................................ 8

Adapting Microwave Blower

for Outside Back Exhaust ................ 17-18

Mount the Microwave Oven ................ 19

[] Recirculating ........................................

Attach Mounting Plate to Wall ............ 20

Preparation of Top Cabinet ................ 20

Check Blower Plate ............................ 21

Mount the Microwave Oven .......... 21-22

Installing or Change the

Charcoal Filter .................................... 22

Before You Use Your Microwave .......................... 23

20 _ 2 2

Installation Types ............................................... 9-22

Hood Exhaust .................................................. 10-11

_ Outside Top ............................

Attach Mounting Plate to Wall ............ 12

Preparation of Top Cabinet ................ 13

Adapting Microwave Blower for

Outside top Exhaust .................. 13-14

Checking for Proper Damper

Operation ............................................ 14

Mount the Microwave Oven .......... 14-15

Adjust the Exhaust Adaptor ................ 15

Connecting Ductwork .......................... 15

]Outside Back Exhaust 16-19

Preparing Rear Wall for

Outside Back Exhaust .......................... 16

Remove Blower Plate .............................. 16

Attach Mounting Plate to Wall ............ 17

Exhaust 12-15

Preparation of Top Cabinet ................ 17

Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

This product requires a three-prong grounded outlet. The installer" must perform a ground continuity check on the power" outlet box before beginning the installation to insure that the outlet box is properly grounded. If not properly grounded, or" if the outlet box does not meet electrical requirements noted

(under ELECTRICAL REQUIREMENTS), a qualified

electrician should be employed to correct any deficiencies.

CAUTION: For personal

safety, remove house fuse or open circuit breaker before beginning

installation to avoid severe or fatal shock injury.

CAUTION: For personal safety, the mounting surface must be capable of supporting the cabinet load, in addition to the added weight of this 63-85 pound

(28.5-38.5 kg) product, plus additional oven loads of

up to 50 pounds (22.7 kg) or a total weight of

113-135 pounds (51.3-61.2 kg).

CAUTION: For personal safety, this product cannot be installed in cabinet arrangements such as an island or a peninsula. It must be mounted to BOTH a top cabinet

AND a wall.

You should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded.

Where a standard two-prong wall receptacle is encountered, it is very important to have it replaced with a properly grounded three-prong wall receptacle, installed by a qualified electrician.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT, DEFORM OR REMOVE ANY OF THE PRONGS

FROM THE POWER CORD. DO NOT USE WITH AN EXTENSION CORD.

ELECTRICAL REQUIREMENTS

Product rating is 120 volts AC, 60 Hertz, 15 amps and

1.6 kilowatts. This product must be connected to a

supply circuit of the proper voltage and frequency. Wire size must conform to the requirements of the

National Electrical Code or the prevailing local code for this kilowatt rating. The power supply

cord and plug should be brought to a separate

15- to 20- ampere branch circuit single grounded

outlet. The outlet box should be located in the cabinet above the microwave oven. The outlet box

and supply circtfit should be installed by a qualified electrician and conform to the National Electrical

Code or the prevailing local code.

NOTE: For easier installation and personal safety, it is

recommended that two people install this product.

IMPORTANT - PLEASE READ CAREFULLY. FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE

PROPERLY GROUNDED TO AVOID SEVERE OR FATAL SHOCK.

The power cord of this appliance is equipped with a

three-prong (grounding) plug which mates with a

standard three-prong (grounding) wall receptacle to minimize the possibility

of electric shock hazard from this appliance.

Ensureproper groundexists

beforeuse

Installation Instructions

DAMAGE--SHIPMENT/ INSTALLATION

• If the unit is damaged in shipment, return the

unit to the store in which it was bought for repair

or replacement.

• If the unit is damaged by the customer, repair or replacement is the responsibility of the customer.

• If the unit is damaged by the installer (if other

than the customer), repair or replacement must be made by arrangement between customer

and installer

PARTS INCLUDED

HARDWARE PACKET

PART

Wood Screws

(1/4" X 2")

ToggleBolts(and wingnuts)(3/16"x3")

QUANTITY

PARTS INCLUDED (CONT.)

ADDITIONAL PARTS

PART QUANTITY

i_!i_i!_!iiii_ii!i!i!ii!i_i!_ii!i!iii_iiii_i!i!i!i!i!_!__ii_i!___i!_i!!i!_!!!!!iiiiiiiii!!!ii!!!i_i_!_!i!i_i_i!i_i!ii!i!iii!iiiii!i!!i!!i!!i!i!i!iiiiiii!ii!i!i!iiii!iii_i'

CombinedTop

Cabinet Templateand

Rear Wall

Template

Installation Instructions

Separately Packed

Grease Filters

Sel?AligningMachine Screws(1/4"-28x 31/4'')

NylonGrommet

(formetalcabinets)

PowerCordStrap (plastic)

You will find the installation hardware contained in

a packet with the unit. Check to make sure you have all these parts.

NOTE: Some extra parts are included.

Exhaust adaptor

Glass

Tray

Turntable Ring

Installation Instructions

TOOLS YOU WILL NEED

# 1Phillipsscrewdriver

Tinsnips(forcutting damper,if required)

Gloves

Scissors (tocuttemplate,if necessary)

Pencil

din===--

Ruleror tapemeasureand

t edge

Electricdrill with 3/16",1/2"and%"

drill bits

Carpentersquare (optional)

Fillerblocksor scrap woodpieces,if needed fortop cabinetspacing (usedonrecessedbottom cabinetinstallationsonly)

Saw(saber,holeor keyhole)

Safetygoggles

MOUNTING SPACE

--3

66" (167,6cm) or Morefrom

the Floorto the Topof the

Microwave

Backsplash

BottomEdgeof

CabinetNeedsto

be30" (76,2cm)

or Morefrom the

CookingSurface

Studfinder or

Level

NOTES:

• The space between the cabinets must be 30" (76.2 cm)wide and free of obstructions.

• If you are going to vent your microwave oven to the outside, see Hood Exhaust Section for

exhaust duct preparation.

• When installing the microwave oven beneath smooth, flat cabinets, be careful to follow the

instructions on the top cabinet template for power cord clearance.

Hammer(optional)

Ductandmaskingtape

Installation Instructions

PLACEMENT OF THE MOUNTING PLATE

I-_ REMOVING THE MICROWAVE

OVEN FROM THE CARTON/ REMOVING THE MOUNTING PLATE

[]Remove the installation instructions, filters, glass

tray and the small hardware bag. Do not remove

the Styrofoam protecting the front of the oven.

[] Fold back all 4 carton flaps fully against carton

sides. Then carefully roll the oven and carton over onto the top side The oven should be resting in the Styrofoam.

Styrofoam_

[]Pull the carton up and off the oven

Cut the middle of the outer protective plastic bag to

remove the mounting plate

Screws-_ Plate

Mounting

I-_ FINDING THE WALL STUDS

i waRm

i Studs

[]Find the studs, using one of the following

methods:

A. Stud finder - a magnetic device which

locates nails.

B. Use a hammer to tap lightly across the

mounting surface to find a solid sound.

This will indicate a stud location

[] After locating the stud(s), find the center by

probing the wall with a small nail to find the edges of the stud. Then place a mark halfway between the edges. The center of any adjacent studs should

be 16" (40.6 cm) or 24" (61 cm) from this mark.

[]Draw a line down the center of the studs.

THE MICROWAVE MUST BE CONNECTED TO AT LEAST ONE WALL STUD.

[]Remove the screws from the mounting plate.

This plate will be used as the rear wall template and for mounting. Reinstall the screws into the holes where they were removed.

Installation Instructions

DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET

Plate positionmbeneath flat bottom cabinet

MountingPlateTabs Touchingthe CabinetBottom

At least30" (76.2cm),

upto 36" (9!.4 cm)

Plate positionmbeneath framed recessed cabinet bottom

MountingPlateTabs

.Touchingthe BackFrame

I I ii 30" (76,2 cm)

to Cooktop

Plate position_beneath recessed bottom

cabinet with front overhang

Mounting Plate with

Tabs Below Cabinet

Bottom the Same Distance as the Front Overhang Depth

30" (76,2 cm)

to Cooktop

Your cabinets may have decorative trim that

interferes with the microwave installation. Remove

the decorative trim to install the microwave properly and to make it level.

THE MICROWAVE MUST BE LEVEL.

Use a level to make sure the cabinet bottom is level. If the cabinets have a front overhang only, with no

back or side frame, install the mounting plate down the same distance as the front overhang depth. This

will

keep the microwave level.

[]

Measure the inside depth of the front overhang.

Draw a horizontal line on the back wall an equal

distance below the cabinet bottom as the inside depth of the front overhang.

For this type of installation with front overhang only, align the mounting tabs with this horizontal line, not touching the cabinet bottom as described in Step D.

Installation Instructions

ALIGNING THE WALL PLATE

j_,,_ Draw a Vertical i Line on Wall _I

I from Center of ,:1

Centerline i Top Cabinet t!t Notches i I_I

-_? o o ? o o cF--o---_o c _ o o Or---o-_o o o_

CAUTION: Wear gloves

to avoid cutting fingers on sharp edges.

[]Draw a vertical line on the wall at the center of the

30" (76.2 cm) wide space.

[]Use the mounting plate as the template for the rear

wall. Place the mounting plate on the wall, making sure that the tabs are touching the bottom of the cabinet or the level line drawn in Step C for cabinets with front overhang. Line up the notch and centerline on the bottom of the mounting plate to the centerline

on the wall.

[]While holding the mounting plate with one hand,

draw circles on the wall at holes A, B, C and D

(see illustration above/actual plate marked with

arrows). Four holes must be used for mounting.

Hole C Area E

I ,

\ Hole D

NOTE: If neither C nor D is in a stud, find a stud

somewhere in area E and draw a fifth circle to line up with the stud. It is important to use at least one wood screw mounted firmly in a stud to support the weight

of the microwave. Set the mounting plate aside. Drill holes on the circles. If there is a stud, drill a sad'

hole for wood screws. For holes that don't line up with a stud, drill a 5/_,,hole for toggle bolts.

NOTE: DO NOT MOUNT THE PLATE AT THIS TIME.

Installation Instructions

INSTALLATION TYPES

This microwave oven is designed for adaptation to the following three types of ventilation:

A. Outside Top Exhaust (Vertical Duct) B. Outside Back Exhaust (Horizontal Duct)

C. Recirculating (Non-Vented Ductless)

-_ OUTSIDE TOP EXHAUST

(VERTICAL DUCT)

Adaptorin Placefor OutsideTopExhaust

(Choose A, B or C)

NOTE: This microwave is shipped assembled for Recirculating. Select the type of ventilation required

for your installation and proceed to that section.

OUTSIDE BACK EXHAUST

(HORIZONTAL DUCT)

AdaptorMust Be Movedto theBackfor

OutsideBackExhaust

[_ RECIRCULATING

(NON-VENTED DUCTLESS)

On models shipped for recirculating exhaust, a disposable charcoal filter is factory installed to help

remove smoke and odors.

Installation Instructions

INSTALLATION INSTRUCTIONS FOR EXTERNAL EXHAUST DUCTING

NOTE: If you need to install ducts, note that the total

duct length of 31/4" x 10" (8.2 x 25.4 cm) rectangular or 5" (10.5 cm) diameter/ 6" (15.2 cm) diameter round duct

should not exceed 120 equivalent feet (36.5 m). Outside ventilation requires a EXTERNAL EXHAUST

DUCT.Read the following carefully.

NOTE: It is important that venting be installed using

the most direct route and with as few elbows as possible. This ensures clear venting of exhaust and helps prevent blockages. Also, make sure dampers swing freely and nothing is blocking the ducts.

Exhaust connection:

The exhaust adaptor has been designed to mate with a standard 31/4'' x 10" (8.2 x 25.4 cm) rectangular duct.

If a round duct is required, a rectangular-to-round transition adaptor must be used. Do not use less than

a 6" (15.2 cm) diameter duct.

EQUIVALENT

DUCT PIECES

Rectangular-to-Round

TransitionAdaptor*

LENGTH

5 Ft,(1,5m)

Maximum duct length:

For satisfactory air movement, the total duct length of 31/4'' x 10" (8.2 x 25.4 cm) rectangular or 5" (10.5 cm)

diameter/6 "(15.2 cm) diameter round duct should not

exceedl20 equivalent feet (36.5 m).

Elbows, transitions, wall and roof caps,

etc., present additional resistance to airflow and are

equivalent to a section of straight duct which is longer than their actual physical size. When calculating the total

duct length, add the equivalent lengths of all transitions and adaptors phrs the length of all straight duct sections.

The chart below shows you how to calculate total equivalent ductwork length using the approximate feet

of equivalent length of some typical ducts.

NUMBER

x USED

x ()

EQUIVALENT LENGTH

Ft,orm

Wall Cap

90° Elbow

45° Elbow

90° Elbow

45° Elbow

RoofCap

StraightDuct6" (15,2cm) Roundor31/4``x 10"

(8,2x 25,4cm)Rectangular

40Ft,(12,2m)

10Ft,(3m)

5 Ft,(1,5m)

25Ft,(7,6m)

5 Ft,(1,5m)

24Ft,(7,3m)

1 Ft,(0,3m)

x ()

Ft,orm

* IMPORTANT: If a rectangular to round transition

adaptor is used, the bottom corners of the damper will have to be cut to fit, using the tin snips, in order

to allow free movement of the damper.

Total Ductwork

Equivalent lengths of duct pieces are based on actual tests and reflect requirements ti)r good venting pertbrmance with any vent hood.

Ft. or m

Installation Instructions

EXTERNAL EXHAUST DUCTING

NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 20.

OUTSIDE TOP EXHAUST (EXAMPLE ONLY)

The following chart describes an example of one possible ductwork installation.

EQUIVALENT NUMBER EQUIVALENT

DUCT PIECES

LENGTH x USED = LENGTH

Roof Cap

12Ft,(3,6m)StraightDuct 12 Ft,(3,6m) x (1) = 12 Ft,(3,6m) (6'715,2cmRound)

Rectangular-to-Round 5 Ft,(1,5m) x (1) = 5 Ft,(1,5m) TransitionAdaptor*

Equivalentlengthsofductpiecesarebasedonactualtestsand

reflectrequirementsfor goodventingperformancewith anyvent hood,

* IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper

will have to be cut to fit, using the tin snips, ira order to allow fi'ee movement of the damper:

24Ft,(7,3m) x (1) 24Ft, (7,3m)

OUTSIDE BACK EXHAUST (EXAMPLE ONLY)

The following chart describes an example of one possible

ductwork installation.

EQUIVALENT NUMBER EQUIVALENT LENGTH* USED = LENGTHDUCT PIECES x

Total Length = 41 Ft. (12.5 m)

":_::[_ Cap (12,2m) x

(_ 90° Elbow 10Ft,(3 m) x

Equivalentlengthsof ductpiecesarebasedonactualtests and reflectrequirementsfor goodventingperformancewith anyventhood,

NOTE: For- back exhaust, care should be taken to align exhaust with space between studs, or"wall should be prepared at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust.

Wall 40Ft,

3Ft,StraightDuct 3Ft, (0,9m) x (31/g'x 10'78,2x 25,4cm

Rectangular)

(1) 40Ft,(12,2m)

(1) = 3Ft,(0,9m)

(2) = 20Ft,(3 m)

Total Length = 63 Ft. (19.2 m)

Installation Instructions

OUTSIDE TOP EXHAUST (Vertical Duct)

INSTALLATION OVERVIEW

A|. Attach Mounting Plate to Wall A2. Prepare Top Cabinet

A3. Adapting Microwave Blower for

Outside Top Exhaust

A4. Check Damper Operation A5. Mount Microwave Oven

A6. Adjust Exhaust Adaptor A7. Connect Ductwork

IMPORTANT NOTES:

• Make sure the screws for the blower motor and blower plate

are securely tightened when they are reinstalled. This will help to prevent excessive

vibration.

• Make sure the motor wiring has been properly routed and secured, and that the wires are not pinched.

ATTACH THE MOUNTING PLATE TO THE WALL

Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach

the plate to a wall stud. []Remove the from the bolts. []Insert the bolts into the mounting

through the holes designated to go into drywall and reattach the toggle wings to 3/4" (19 mm) onto

each bolt.

toggle

wings

plate

To use toggle bolts:

Spacing for Toggles More Than Wall

-_l_i_--Thickness

Mounting

Plate,

]Place the mounting plate against the wall and

insert the toggle wings into the holes in the wall

to mount the plate.

NOTE: Before tightening toggle bolts and wood

screw, make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed

flush against the wall and that the plate is properly centered under the cabinet.

CAUTION: Be careful to avoid pinching fingers

between the back of the mounting plate and the wall.

]Tighten all bolts. Pull the plate away fl'om the wall

to help tighten the bolts.

iToggle Wings

Bolt End

Installation Instructions

I-_ USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP CABINET

You need to drill holes for the top support screws, a

hole large enough for the power cord to fit through,

and a cutout large enough for the exhaust adaptor.

• Read the instructions on the TOP CABINET

TEMPLATE.

• Tape it underneath the top cabinet.

• Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.

Careflflly pull out the blower unit. The wires will extend far enough to allow you to adjust

the blower unit.

jEnd B

EndA _P'_ _

Microwave

Roll the blower unit 90 ° so that fan blade openings are facing out the top of the

microwave.

Before Rotation After Rotation

Backof

Microwave

ADAPTING MICROWAVE

BLOWER FOR OUTSIDE

TOP EXHAUST

[] Place the microwave in its upright position,

with the top of the unit facing up.

I I

_ BI0wer Plate

<l__---------._,_--__f] 1 Back0r

Micr0wave

Remove the screw that holds the blower plate to the microwave. Remove and save the screw

holding the blower motor to the microwave.

[]Place the blower unit back into the opening.

CAUTION: Do not pull or stretch the blower

,ow r o,or

Screw

unit wiring. Make sure the wires are not pinched, and that they are properly secured.

Backof Microwave

Installation Instructions

ADAPTING MICROWAVE

BLOWER FOR OUTSIDE

TOP EXHAUST

Secure blower unit to microwave with the screw removed in Step 1. Make sure the screw is tight.

Replace blower plate with the screw removed in Step 1. Make sure the screw is tight.

Back of

Micr0wave

Attach the exhaust adaptor to the top of the

[]

blower plate by sliding it into the guides of the blower plate.

Adaptor

k0cking lab Push in securely until it is in the locking tabs. Take care to assure that the damper hinge is installed so that the damper swings freely.

MOUNT THE MICROWAVE OVEN

FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE

INSTALL THIS MICROWAVE OVEN.

IMPORTANT: Do not grip or use handle

during installation. NOTE: If your cabinet is metal, use the nylon

grommet around the power cord hole to prevent cutting of the cord.

NOTE: We recommend using filler blocks if the

cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are

not used, case damage may occur from overtightening screws.

NOTE: When mounting the

microwave oven, thread power cord through hole in

bottom of top cabinet. Keep

it tight throughout Steps

1-3. Do not pinch cord or

lift oven by pulling cord.

[]Lift tilt it

microwave,

forward, and hook slots at back bottom

edge onto four lower tabs of mounting plate.

I-_ CHECK FOR PROPER

DAMPER OPERATION

Blower Plate Exhaust Adaptor

X ,,_,,,___----Damper

• Make sure tape securing damper is removed and damper pivots easily before mounting microwave.

• You will need to make adjustments to assure proper alignment with your house exhaust duct after the

microwave is installed.

[]Rotate fl'ont of

up against cabinet bottom.

Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet.

oven

Installation Instructions

MOUNT THE MICROWAVE OVEN (cont.)

Cabinet Front

..._._/_ Cabinet Bottom Shelf

/ Filler Block

/_,-- ;:::___

/ _F_[_/_ TEq uivalent

/ | : :bPitnhet

_:__!tI II:' _L Recess

J"\l !U _-_ Self-Aligning Screw

Microwave OvenTop

I_ Attach the microwave oven to the top cabinet.

[] Insert 2 self-aligning screws

through outer top cabinet holes. Turn two flfll turns on

each screw.

ADJUST THE EXHAUST

ADAPTOR

Open the top cabinet and adjust the exhaust adaptor to connect to the house duct.

Backof

BlowerPlate Damper Microwave

Side-to-SideAdjustment, Slidethe ExhaustAdaptor

asNeeded

I-_ CONNECTING DUCTWORK

HouseDuct

[]Tighten center

screw completely.

[] Tighten the outer two screws to the top of the

microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.)

[] Install grease filters. See the Owner's Manual

packed with the microwave.

]Extend the house duct down to connect to

the exhaust adaptor.

]Seal exhaust duct joints using furnance duct tape

for t_gh temperature applicatiorgs.

Installation Instructions

OUTSIDE BACK EXHAUST (Horizontal Duct)

INSTALLATION OVERVIEW

BI. Prepare Rear Wall B3. Remove Blower Plate

B3. Attach Mounting Plate to Wall B4. Prepare Top Cabinet

BS. Adjust Blower B6. Mount the Microwave Oven

IMPORTANT NOTES:

• Make sure the screws for the blower motor and blower plate

are securely tightened when they are reinstalled. This will help to prevent excessive

vibration.

• Make sure the motor wiring has been properly routed and secured, and that the wires are not pinched.

PREPARING THE REAR WALL

FOR OUTSIDE BACK EXHAUST

You need to cut an opening in the rear wall for outside exhaust.

• Read the instructions on the REAR

WALL TEMPLATE.

• Tape it to the rear wall, lining up with the

holes previously drilled for holes A and B in the wall plate.

• Cut the opening, following the instructions of the

REAR WALL TEMPLATE.

REMOVE BLOWER PLATE

Remove and save the screw that holds the blower plate to the microwave. Lift off the blower plate.

Blower Plate

l _ _ _ Backof

Microwave

Installation Instructions

_] ATTACH THE MOUNTING

PLATE TO THE WALL

Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach

the plate to a wall stud.

]Remove the toggle wings from the bolts. ]Insert the bolts into the mounting plate through

the holes designated to go into drywall and reattach the toggle wings to 3/4" (19 mm) onto each bolt.

To use toggle bolts:

USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP

CABINET

You need to drill holes for the top support screws and

a hole large enough for the power cord to fit through.

• Read the instructions on the TOP CABINET

TEMPLATE.

• Tape it underneath the top cabinet.

• Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes

in the cabinet bottom.

Spacing for Toggles More

_-_i_,---Than Wall Thickness

Mounting

Plate

]Place the mounting plate against the wall and

insert the toggle wings into the holes in the wall to mount the plate.

roggle Wings

Bolt End

NOTE: Before tightening toggle bolts and wood

screw, make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly

centered under the cabinet.

CAUTION: Be careflfl to avoid pinching fingers between the back of the mounting plate and the wall.

Tighten all bolts. Pull the plate away from the wall to help tighten the bolts.

ADAPTING MICROWAVE

BLOWER FOR OUTSIDE BACK EXHAUST

[]Remove and that holds blower motor

to microwave.

Careflflly pull out the blower unit. The wires

will extend far enough to allow you to adjust

the blower unit.

save screw

Blower Motor

_" - _ Blower Motor

v .,_ Screw

EndA

Installation Instructions

ADAPTING MICROWAVE

BLOWER FOR OUTSIDE

BACK EXHAUST (cont.)

[] Roll the blower" unit 90 °

Before Rotation After Rotation

Microwave

Rotate blower unit counterclockwise 180 ° .

Before Rotation

Back of Microwave

[]Gently remove the wires from the

Reroute the wires through grooves on other side of the blower unit.

After Rotation

grooves.

Backof Microwave

Back of

Microwave

[]Place the blower unit back into the opening.

EndA

End

CAUTION: Do not pull or stretch the blower

unit wiring. Make sure the wires are not pinched, and that they are properly secured.

NOTE: The blower unit exhaust openings should match exhaust

openings on rear of microwave oven.

[ ecure the blower unit to the microwave with

the original screw.

Blower Plate

,!_ Microwave

I _ Back of

Blower Motor Screw

Before Rerouting After Rerouting

Wires Routed ThroughRight Side Wires Routed Through Left Side

_6_ Roll the blower unit 90 ° so that fan blade

openings are facing out the back of the microwave.

Before Rolling

Microwave

After Rolling

Back of Microwave

[]Replace the blower in theplate

as before with the screw. Make sure the screw

is tight.

[]Attach the exhaust the of theadaptor

oven by sliding it into the guides at the top

center of the back of the oven.

same

to Fear

Adaptor

Guide

Push in securely until it is in the lower locking tabs. Take care to assure that the damper hinge

is installed so that it is at the top and that the damper swings freely.

Locking Tabs

position

Backof Microwave

Guide

Installation Instructions

MOUNT THE MICROWAVE OVEN

FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE

INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handle

during installation.

NOTE: If your cabinet is metal, use the nylon grommet around the power" cord hole to prevent

cutting of the cord. NOTE: We recommend using filler blocks if the

cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not used, case damage may occur from

overtightening screws.

Cabinet Front

Cabinet Bottom Shelf

FillerBlock

-_ Equivalent

to Depth of Cabinet

Recess

Self-Aligning Screw

Microwave Oven Top

[]Attach the microwave oven to the top cabinet.

[] Insert 2 self-aligning screws

through outer top cabinet holes. Turn two flfll turns on

each screw.

NOTE: When mounting the

microwave oven, thread power cord through hole in

bottom of top cabinet. Keep

it tight throughout Steps

1-3. Do not pinch cord or"

lift oven by pulling cord.

[]Rotate fl'ont of

up against cabinet bottom.

[]Insert a self-aligning screw through top center

cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the

threads have engaged. (It will be completely tightened later:) Be sure to keep power cord

tight. Be careful not to pinch the cord, especially

when mounting flush to bottom of cabinet.

oven

[]Lift tilt it

microwave,

forward, and hook slots at back bottom

edge onto four lower tabs of mounting plate.

[]Tighten center

screw completely.

[] Tighten the outer two screws to the top of the

microwave oven. (While tightening screws, hold the microwave oven in place against the wall and

the top cabinet.)

[] Install grease filters. See the Owner's Manual

packed with the microwave.

Installation Instructions

RECIRCULATING (Non-Vented Ductless)

INSTALLATION OVERVIEW

C1. Attach Mounting Plate to Wall C3. Prepare Top Cabinet

C3. Check Blower Plate C4. Mount the Microwave Oven

C5. Install or change Charcoal Filter

IMPORTANT NOTES:

• Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled.

This will help to prevent excessive vibration.

• Make sure the motor wiring has been properly routed and secured, and that the wires are not pinched.

ATTACH THE MOUNTING PLATE TO THE WALL

Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach

the plate to a wall stud.

[]Remove the from the bolts.toggle wings

Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to 3/4" (19 mm) onto each bolt.

To use toggle bolts:

]Place the mounting plate against the wall and

insert the toggle wings into the holes in the wall

to mount the plate.

NOTE: Before tightening toggle bolts and wood

screw, make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly

centered under the cabinet.

CAUTION: Be careful to avoid pinching fingers

between the back of the mounting plate and the wall.

Tighten all bolts. Pull the plate away from the wall to help tighten the bolts.

I-_ USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP CABINET

You need to drill holes for the top support screws and a hole large enough for the power cord to fit through.

Mounting

Plate,

Spacing for Toggles

More Than Wall

÷l_-_.i_,----Thickness

lToggle Wings

Bolt End

• Read the instructions on the TOP CABINET

TEMPLATE.

• Tape it underneath the top cabinet.

• Drill the holes, following the instructions on the

TOP CABINET TEMPLATE

CAUTION: Wear safety goggles when drilling holes

in the cabinet bottom.

Installation Instructions

CHECK BLOWER PLATE

Blower Plate

• Place the microwave in its upright position, with the top of the unit facing up.

• Check to see that the blower plate is correctly installed on the unit.

MOUNT THE MICROWAVE OVEN

FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE

INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handle

during installation. NOTE: If your cabinet is metal, use the nylon

grommet around the power cord hole to prevent cutting of the cord.

NOTE: We recommend using filler blocks if the

cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not used,

case damage may occur from overtightening

screws.

NOTE: When mounting the

microwave oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps

1-3. Do not pinch cord or

lift oven by pulling cord.

[]Rotate front of oven

up against cabinet bottom.

[]Insert a self-aligning screw through top center

cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the

threads have engaged. (It will be completely tightened later.) Be sure to keep power cord

tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet.

Cabinet Front

Cabinet Bottom Shelf

MicrowaveOvenTop

[]Lift microwave, tilt

it forward, and hook slots at back bottom

edge onto four lower tabs of mounting plate.

Filler Block

Equivalentto Depth

of CabinetRecess

Self-AligningScrew

[]Attach the microwave oven to the top cabinet.

+ 49 hidden pages