Friedrich CP Line CP08, CP Line ZQ10, CP Line ZQ08, ZQ08, ZQ10 Installation And Operation Manual
Room Air Conditioner
Installation and Operation
Manual
*_'riedrich
CP Line
115 Volts • CP08 • ZQ08 • ZQ10
Registering Your Room Air Conditioner
Model information can be found on the name plate located on the
side of the unit near the control panel. Please complete and mail
the owner registration card furnished with this product or register
on-line at www.friedrich.com (USA only). For your future
convenience, record the model information here.
MODEL NUMBER SERIAL NUMBER PURCHASE DATE
Congratulations!
You have purchased a Friedrich
room air conditioner. The Friedrich
units are designed to give maximum
comfort and quietness.
Table of Contents
Introduction .................................................................................. 2
Safety Precautions ....................................................................... 3
How to operate your Friedrich ................................................... 5
How to operate your Friedrich ZStar® ......................................6
Adjusting the Air Flow Direction................................................. 7
Care and Maintenance ................................................................. 8
Hardware Location ....................................................................... 9
Installation Instructions ........................................................ 15
Troubleshooting Tips ................................................................. 17
Warranty ...................................................................................... 18
Introduction
Before Operating Your Unit
Make sure the wiring is adequate for your unit.
If you havefuses, they should beof the time delay type. Beforeyou install or relocate this unit, be sure that
the amperage rating of the circuit breaker or time delay fuse does notexceed the amp rating listed in figure 1.
DO NOT use an extension cord.
The cord provided will carry the proper amount of electrical powerto the unit; an extension cord will not.
Make sure that the receptacle is compatible with the wall plug provided.
This insures proper grounding. If you have a two-prong receptacle you will need to havethe circuit replaced
by a certified electrician with a grounded circuit that meets all national and local codes and ordinances.You
must use the three-prong plug furnished with the air conditioner.
MODEL
CP08 ZQ08 ZQ10
CIRCUIT
RATING OR
TIME DELAY
FUSE
AMP VOLT
15 125
PLUG FACE
NEMA NO.
5-15P
@
Figure 1
For the Best Cooling Performance and Energy Efficiency
Keep the filter clean
Make sure that your air conditioner is always in top performing condition by cleaning the filter regularly.
Instructionsfor removing and cleaningthe filter can be found on page 8.
Provide good airflow
Make sure that the airflow to and from the unit is clear. Your air conditioner puts the air out atthe top of
the unit, and takes in air at the bottom. Airflow is critical for good operation. It is just as important on the
outside ofthe building that the airflow around the unit exterior is not blocked.
Unit Placement
Ifyour air conditioner can be placed in a window or a wall that is shaded by a tree or another building, the
unit will operate even more efficiently. Using drapes or blinds on the sunny sideof the dwellingwill also
add toyour unit's efficiency.
/nsu/ation
Good insulation will be a big help in maintaining desirable comfort levels. Doorsshould have weather
stripping. Be sureto caulk around doors and windows.
Safety Precautions
To prevent injury and property damage, follow these instructions.
• incorrect operation due to ignoring of instruction can cause harm or damage. The seriousness is classified
by the following indications.
'_//_ WARNING This symbol indicates the possibility of death or serious injury. /
J
/_ CAUTION This symbol indicates the possibility of injury or damage to
properties only.
• Meanings of symbols used in this manual are as shown below.
Never Do This
,0__ Always Do This
I/_ WARNING}
• Otherwise, it will cause electric
shock or fire due to heat
generation.
• it will cause electric shock or fire
due to heat generation.
• it wi(I cause eiectric shock or fire.
• If the power cord is damaged, it must
be reptaced by the manufacturer or a
Friedrich-certified service agent.
• it will cause electric shock or fire • it will cause electric shock.
due to heat generation.
®
• This could lead to hea(th probiems.
• They are sharp and may cause
an injury.
I CAUTION I
• Water may enter the unit and
degrade the insulation. It may
cause an electric shock.
• Since the fan rotates at high
speed during operation, it may
cause an injury.
® ®
• It could cause dust to
accumulate on the heat
exchanger.
• It may cause an electric shock.
• This could injure the pets
or plants.
• It may cause a fire or
deformation of the cabinet.
• Do not use this air conditioner to
preserve precision devices, food,
pets, plants, and art objects.
It may cause deterioration of
quality, etc.
• Use caution when handling the
case. Grip it firmly and do not allow
it to slip while holding it.
• Use heavy gloves to handte
the case if necessary.
• DO NOT
allow the
case to slide
against
your skinT
edges
How to operate your Friedrich
Fan Speed
Timer Mode //il I
C ° _
@
Control and Remote Control Operations
I. POWER
Operation begins when this button is pressed
and stops when you press the button again.
2. TEMPERATURE CONTROL
The thermostat monitors room temperature
to maintain the desired temperature.
The thermostat can be set between
60°F~86°F (16°C~30°C).
The unit takes an average of 30 minutes to
adjust the roomtemperature by I°F.
3. OPERATION MODE SELECTOR
Select cooling mode to cool the room.
Select Money Saver_ mode for energy
saving operation.
Select fan mode for basic ventilatingfan
operation.
Select dry mode for dry operation.
4.FAN SPEEDSELECTOR
Forincreased powerwhile cooling, select a
higher fan speed.
3 steps: High; Low; Med
5. ON/OFF TIMER
The timer can be set to start and stop the
unit inhourly increments (up to 12 hours).
6.REMOTE CONTROLSENSOR
Inserting the Remote Control Batteries
1.Push out the cover on the back
of the remote control with your
thumb
2. Pay attention to polarity and
insert two new AAA 1.5V
batteries.
3. Reattach the cover.
NOTE: Donotuserechargeabiebatteries.Makesurethat
bothbatteriesarenew.
• Inorderto preventdischarge,removethebatteriesfrom
theremotecontrolif theairconditioneris notgoingto be
usedforanextendedperiodoftime
Keeptheremotecontrolawayfromextremelyhotor
humidplaces.
Tomaintainoptimaloperationofthe remotecontrol,the
remotesensorshouldnotbeexposedtodirectsunlight.
•Theremotecontrolcanbemountedonawallusingthe
mountableholder.(Friedrichdoesnotprovidethis.)