Friedrich CP12, CP10A10, CP10C10, CP10N10, CP12A10 Installation And Operation Manual

...

ENGLISH FRANÇAIS ESPAÑOL

Room Air Conditioner Installation and Operation Manual

MODEL NUMBER SERIAL NUMBER PURCHASE DATE

CP Line

920-151-00 (12/04)

CP10 CP12115 Volts

Registering Your Room Air Conditioner

Model information can be found on the name plate located on the side of the unit near the control panel. Please complete and mail the owner registration card furnished with this product or register on-line at www.friedrich.com (USA only). For your future convenience, record the model information here.

Congratulations! Thank you for choosing Friedrich.

Your Friedrich unit is designed for maximum comfort and quietness.

Table of Contents

Introduction ..................................................................................2

Safety Precautions.......................................................................3

How to operate your Friedrich ...................................................5

Adjusting the Air Flow Direction.................................................6

Care and Maintenance.................................................................7

Hardware Location.......................................................................8

Installation Instructions

........................................................

Troubleshooting Tips.................................................................16

Warranty......................................................................................17

ENGLISH

Before Operating Your Unit

Make sure the wiring is adequate for your unit.

If you have fuses, they should be of the time delay type. Before you install or relocate this unit, be sure that the amperage rating of the circuit breaker or time delay fuse does not exceed the amp rating listed in figure 1.

DO NOT use an extension cord.

The cord provided will carry the proper amount of electrical power to the unit; an extension cord will not.

Make sure that the receptacle is compatible with the wall plug provided.

This insures proper grounding. If you have a two-prong receptacle you will need to have the circuit replaced by a certified electrician with a grounded circuit that meets all national and local codes and ordinances. You must use the three-prong plug furnished with the air conditioner.

Figure 1

For the Best Cooling Performance and Energy Efficiency

Keep the filter clean

Make sure that your air conditioner is always in top performing condition by cleaning the filter regularly. Instructions for removing and cleaning the filter can be found on page 7.

Provide good airflow

Make sure that the airflow to and from the unit is clear. Your air conditioner puts the air out at the top of the unit, and takes in air at the bottom. Airflow is critical for good operation. It is just as important on the outside of the building that the airflow around the unit exterior is not blocked.

Unit Placement

If your air conditioner can be placed in a window or a wall that is shaded by a tree or another building, the unit will operate even more efficiently. Using drapes or blinds on the sunny side of the dwelling will also add to your unit's efficiency.

Insulation

Good insulation will be a big help in maintaining desirable comfort levels. Doors should have weather stripping. Be sure to caulk around doors and windows.

Introduction

MODEL

CP10 CP12

AMP VOLT NEMA NO.

15 125 5-15P

CIRCUIT

RATING OR

TIME DELAY

FUSE

PLUG FACE

Safety Precautions

To prevent injury and property damage, follow these instructions.

■ Incorrect operation due to ignoring of instruction can cause harm or damage. The seriousness is classified by the following indications.

WARNING

WARNING This symbol indicates the possibility of death or serious injury. CAUTION

This symbol indicates the possibility of injury or damage to properties only.

■ Meanings of symbols used in this manual are as shown below.

Never Do This

Always Do This

Plug in the power plug properly.

• Otherwise, it will cause electric shock or fire due to heat generation.

Do not operate or stop the unit by inserting or pulling out the power plug.

• It will cause electric shock or fire due to heat generation.

Do not damage or use an unspecified power cord.

• It will cause electric shock or fire.

•

If the power cord is damaged, it must be replaced by the manufacturer or a Friedrich-certified service agent.

Do not modify power cord length or share the outlet with other appliances.

• It will cause electric shock or fire due to heat generation.

Do not operate with wet hands or in damp environment.

• It will cause electric shock.

Do not direct air flow directly at room occupants.

•

This could lead to health problems

ENGLISH

N S

Sharp edges

When the air filter is to be removed, do not touch the metal parts of the unit.

• They are sharp and may cause an injury.

Do not clean the air conditioner with water.

• Water may enter the unit and degrade the insulation. It may cause an electric shock.

When the unit is to be cleaned, switch the unit off, and unplug it.

• Since the fan rotates at high speed during operation, it may cause an injury.

Do not operate the unit without the air filter or when the front intake grille has been removed.

• It could cause dust to accumulate on the heat exchanger.

Do not put a pet or house plant where it will be exposed to direct air flow.

• This could injure the pets or plants.

Do not use for special purposes.

• Do not use this air conditioner to preserve precision devices, food, pets, plants, and art objects. It may cause deterioration of quality, etc.

Do not apply an insecticide or flammable spray.

• It may cause a fire or deformation of the cabinet.

SHARP EDGES!

The edges of the case can be SHARP!

• Use caution when handling the case. Grip it firmly and do not allow it to slip while holding it.

•

Use heavy gloves to handle the case if necessary.

•

DO NOT allow the case to slide against your skin!

How to operate your Friedrich

Power

Temp

Fan Speed

Timer Mode

453

Control and Remote Contr ol Operations

1. POWER

Operation begins when this button is pressed and stops when you press the button again.

2. TEMPERATURE CONTROL

The thermostat monitors room temperature to maintain the desired temperature. The thermostat can be set between 60°F~86°F (16°C~30°C). The unit takes an average of 30 minutes to adjust the room temperature by 1°F.

3. OPERATION MODE SELECTOR

Select cooling mode to cool the room. Select Money Saver® mode for energy saving operation. Select fan mode for basic ventilating fan operation. Select dry mode for dry operation.

4. FAN SPEED SELECTOR

For increased power while cooling, select a higher fan speed. 3 steps: High; Low; Med

5. ON/OFF TIMER

The timer can be set to start and stop the unit in hourly increments (up to 12 hours).

6. REMOTE CONTROL SENSOR

Inserting the Remote Control Batteries

1. Push out the cover on the back of the remote control with your thumb

2. Pay attention to polarity and insert two new AAA 1.5V batteries.

3. Reattach the cover.

NOTE:

Do not use rechargeable batteries. Make sure that

both batteries are new.

• In order to prevent discharge, remove the batteries from the remote control if the air conditioner is not going to be used for an extended period of time Keep the remote control away from extremely hot or humid places. To maintain optimal operation of the remote control, the remote sensor should not be exposed to direct sunlight.

• The remote control can be mounted on a wall using the mountable holder.(Friedrich does not provide this.)

ENGLISH

VENTCLOSE

OPEN

Part

Adjusting the Air Flow Direction

Vent Control

For maximum cooling efficiency, CLOSE the vent. This will allow internal air circulation. OPEN the vent to discharge stale air.

NOTE : Before using the ventilation feature, position

the vent lever by pulling Part A out straight and snapping it into place.

Adjusting the Air Flow Direction

Airflow can be adjusted by changing the direction of the air conditioner's louvers.

• Adjusting Horizontal Air Flow Direction

Adjusting the vertical louvers left and right will change horizontal airflow.

• Adjusting Vertical Air Flow Direction

Adjusting the horizontal louver up and down will change vertical airflow. The louver can be adjusted by pressing in at the top or button of the horizontal louver.

Adjusting horizontal air flow Adjusting vertical air flow

• Recommended orientation of louvers

Adjust louvers to face upwards when cooling to maximize cooling efficiency.

Drain pipe

Drain cap

Care and Maintenance

Turn the power off and unplug the power plug before cleaning the air conditioner.

Air Filter

The air filter behind the inlet grille should be checked and cleaned at least once every 2 weeks (or as necessary) to maintain optimal performance of the air conditioner.

How to remove the air filter

1. The grille may be opened from the top for easy maintenance after installation.

2. Open the inlet grille by pulling out on the exposed door on the top of the unit (based on installation).

3. Pull the tab slightly to release the filter. Pull the filter in the same direction as the opening.

4. Clean the filter with warm, soapy water.

5. Rinse off and gently shake off excess water from the filter. Make sure filter is completely dry before replacing it.

Drainage

The base pan may overflow due to high humidity. To drain the excess water, remove the drain cap from the back of the unit and secure the drainpipe. When pressing the drainpipe into place, apply force in the direction away from the fins to avoid injuring yourself.

ENGLISH

1 2

Power cord

11 14

Hardware Location

Product Features

Positioning the Power cord

CAUTION

This appliance should be installed in accordance with local and national wiring regulations. This manual acts as a guide to help to explain product features.

1. CABINET

2. FRONT GRILLE

3. AIR FILTER

4. AIR INTAKE (INLET GRILLE)

5. AIR DISCHARGE

6. VERTICAL AIR DEFLECTOR (HORIZONTAL LOUVER)

7. EVAPORATOR

8. HORIZONTAL AIR DEFLECTOR (VERTICAL LOUVER)

9. CONTROL PANEL

10. POWER CORD

11. COMPRESSOR

12. BASE PAN

13. BRACE

14. CONDENSER

15. REMOTE CONTROL

You can choose between two methods below according to your window stool shape and preference.

• Fasten the stopper using 2 screw holes, and lead out the power cord through slit "A".

• Fasten the stopper using left screw hole, and rotate properly to lead the power cord out through slit "B".

Using slit "A" Using slit "B"

27" to 39"

Offset

/2" to 11/4"

Sill

Exterior

Interior wall

/8" min.

(Without frame curtain)

Stool

16" min

(With frame curtain)

About

/2"

30"~60"

Awning

Cooled air

Fence

Over 20"

Heat

radiation

How to Install the Unit

1. To prevent vibration and excess noise, make sure the unit is installed securely and firmly

2. Install the unit where the sunlight does not shine directly on the unit.

3. The outside of the cabinet must extend outward for at least 12" and there should be no obstacles, such as a fence or wall, within 20" from the back of the cabinet, as it will prevent heat radiation of the condenser. Restriction of outside air will greatly reduce the cooling efficiency of the air conditioner.

CAUTION: All side louvers of the cabinet must remain exposed and unobstructed to the outside of the structure.

4. Install the unit with a rear, downward slope, so the back is slightly lower than the front (about 1/4" buble on a level). This will force condensation to flow to the outside.

5. Install the unit with the bottom about 30"~60" above the floor level.

Window Requirements

NOTE: All supporting parts should be secured to firm wood, masonry, or metal.

• This unit is designed for installation in standard

double hung windows with actual opening widths from 27" to 39".

• The top and bottom window sash must open

sufficiently to allow a clear vertical opening of 16" from the bottom of the upper sash to the window stool.

ENGLISH

2 3 4

765

Shipping Screws

(Type A)

Installation Kit Contents

NO. NAME OF PARTS Q'TY

1 FRAME CURTAIN 2 2 SILL SUPPORT 2 3 BOLT 2 4 NUT 2 5 SCREW (TYPE A) 16 6 SCREW (TYPE B) 3 7 SCREW (TYPE C) 5 8 FOAM-STRIP 1

9 UPPER GUIDE 1 10 FOAM-PE 1 11 FRAME GUIDE 2 12 WINDOW LOCKING BRACKET 1 13 FOAM-PE 1

Suggested Tool Requirements

SCREWDRIVER(+, -), RULER, KNIFE, HAMMER, PENCIL, LEVEL

PREPARATION OF CHASSIS

1. Remove the screws which fasten the cabinet at both sides and at the back.(4 total)

2. Slide the unit from the cabinet by gripping the base pan handle and pulling forward while bracing the cabinet.

3. Cut the window sash seal to the proper length. Peel off the backing and attach the Foam-PE to the underside of the window sash.

4. Remove the backing from the top upper guide Foam-PE

and attach it to the bottom of the Upper Guide .

5. Attach the upper guide onto the top of the cabinet with 3 Type A screws .

6. Insert the Frame Guides into the bottom of the cabinet.

7. Insert the Frame Curtain into the Upper Guide and Frame Guides .

8. Fasten the curtains to the unit with 4-Type A screws .

INDOOR OUTDOOR

Sill Support

Nut

Bolt

INDOOR OUTDOOR

Cabinet

About

/2"

Frame Guide

Screw(Type A)

Upper Guide

Window stool

Front Angle

Window Sash Upper guide

Frame Curtain

Foam-pe

Cabinet

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Cabinet Installation

1. Open the window. Mark a line on center of the window stool. Carefully place the cabinet on the window stool and align the center mark on the bottom front with the center line marked in the window stool.

2. Pull the bottom window sash down behind the Upper Guide until they meets.

NOTE: Do not pull the window sash down so

tightly that the movement of Frame Curtain is restricted.

3. Loosely assemble the Sill Support using the parts in Fig. 3.

4. Select the position that will place the Sill Support near the outer most point on sill (See Fig. 4)

NOTE: Be careful when you install the cabinet

(Frame Guides are broken easily).

5. Attach the Sill Support to the cabinet track hole in relation to the selected position using 2 -type A screws in each support (See Fig. 4).

ENGLISH

Sash track

Front Angle

About

/2"

Screw(Type B)

Sill Support

Foam-Strip

Fig. 5

Type C

Fig. 6

Screw(Type A)

Screw

(Type A)

Power cord

Fig. 7

Fig. 8

6. The cabinet should be installed with a very slight tilt (about 1/2") downward toward the outside (See Fig. 5). Adjust the bolt and the nut of Sill Support for balancing the cabinet.

7. Attach the cabinet to the window stool by driving the screws [Type B: Length 16mm (5/8 inch) and below.] through the front angle into window stool.

8. Pull each Frame Curtain to each window sash track, and repeat step 2.

9. Attach each Frame Curtain to the window sash using screws (Type C). (See Fig. 6)

CAUTION: Do not drill a hole in the bottom pan.

The unit is designed to operate with approximately 1/2" of water in bottom of pan. There is no need to add water if the pan is dry.

10. Slide the unit into the cabinet. (See Fig. 7)

CAUTION: For security purpose, reinstall the 2

screws (Type A) at cabinet's side, that were removed in step 1 on page 10.

11. Cut the Foam-Strip to the proper length

(window width) and insert between the upper window sash and the lower window sash. (See Fig. 8)

Window locking bracket

Fig. 9

Fig. 10

Fig. 11

12. Attach the Window Locking Bracket with a Type C

screw . (See Fig. 9)

13. Attach the front grille to the cabinet by inserting the

tabs on the grille into the tabs on the front of the cabinet. Push the grille in until it snaps into place. (See Fig. 10)

14. Pull down the inlet grille and secure it with a Type A

screw through the front grille. (See Fig. 11)

15. Window installation of room air conditioner is now

completed. See ELECTRICAL DATA for inserting power cord to electrical outlet.

ENGLISH

NOTE TO INSTALLER: Leave these instructions with the air conditioner after installation is completed.

NOTE TO CONSUMER: Keep this Installation and Operation Manual for future use.

Important notes:

It is recommended that proper attire be worn during installation. For personal safety, this air conditioner must be properly grounded. It is important to have the wall outlet and circuit checked by a qualified electrician if there is any doubt as to whether a proper ground exists.

CAUTION:

Do not under any circumstances, cut or remove the third (ground) prong from the power cord.

Do not change the plug on the power cord of this air conditioner.

Aluminum house wiring may present special problems–consult a qualified electrician.

Before You Begin

Read these instructions completely and carefully.

Installation Instructions

❒ Phillips-head screwdriver ❒ Flat-blade screwdriver ❒ Ruler or tape measure

❒ Scissors or knife ❒ Pencil ❒ Level ❒ Hammer

Tools You Will Need

115V~

Use of extension cords

Because of potential safety hazards, we strongly discourage the use of an extension cord. However, if you wish to use an extension cord, use a CSA certified/UL-listed3-wire (grounding) extension cord, rated 15A,125V. All wiring should be made in accordance with local electr ical codes and regulations.

Aluminum house wiring may pose special problems. Consult a qualified electrician.

NOTICE

ELECTRICAL SAFETY

IMPORTTANT GROUNDING INSTRUCTIONS

Air conditioner has a three-prong grounding plug on its power supply cord, which must be plugged into properly grounded three-prong wall receptacle for your protection against possible shock hazard.

115V~

Use Wall Receptacle

Standard 125V, 3-wire grounding receptacle rated 15A, 125V AC

Use 15 AMP. time delay fuse or 15 AMP. circuit breaker.

Power cord may include a current interrupter device. A test and reset button is provided on the plug case. The device should be tested on a periodic basis by first pressing the TEST button and then the RESET button. If the TEST button does not trip or if the RESET button will not stay engaged, discontinue use of the air conditioner and contact a qualified service technician.

Electrical Data

Power Supply

Electrical safety

ENGLISH

Troubleshooting Tips

Troubleshooting Tips save time and money! Review the chart below first and you may not need to call for service.

Problem Possible Causes What To Do

■ The air conditioner is unplugged.

■ The fuse is blown/circuit breaker is tripped.

■ Power failure.

■ The current interrupter

device is tripped.

■ Airflow is restricted.

■ The THERMOSTAT may

not be set high enough.

■ The air filter is dirty.

■ The room may have been

hot.

■ Cold air is escaping.

■ Cooling coils have iced up.

■ Ice blocks the air flow and

stops the air conditioner from cooling the room.

• Make sure the air conditioner plug is pushed completely into the outlet.

• Check the house fuse/circuit breaker box and replace the fuse or reset the breaker.

• If power failure occurs, turn the mode control to Off. When power is restored, wait 3 minutes to restart the air conditioner to prevent tripping of the compressor overload.

• Press the RESET button located on the power cord plug. If the RESET button will not stay eng aged, discontinue use of the air conditioner and contact a qualified service technician.

• Make sure there are no curtains, blinds, or furniture blocking the front of the air conditioner.

• Push temperature setting button to coolest temperature setting of 60°F.

• Clean the filter at least every 2 weeks. See the operating instructions section.

• When the air conditioner is first turned on you need to allow time for the room to cool down.

• Check for open furnace floor registers and cold air returns.

• Set the air conditioner's vent to the closed position.

• See Air Conditioner Freezing Up below.

• Set the mode control on high fan until the ice thaws

out.

Air conditioner does not start

Air conditioner does not cool as it should

Air conditioner freezing up

Normal Operation

• You may hear a pinging noise caused by water being picked up and thrown against the condenser on rainy days or when the humidity is high. This design feature helps remove moisture and improve efficiency.

• You may hear the thermostat click when the compressor cycles on and off.

• Water will collect in the base pan during high humidity or on rainy days. The water may overflow and

drip from the outdoor side of the unit.

• The fan may run even when the compressor does not.

• Your air conditioner is designed to cool in warm weather when the outside temperature is above 60°F(16°C) and below 115°F(46°C).

Abnormal Operation

+ 40 hidden pages

Friedrich CP12, CP10A10, CP10C10, CP10N10, CP12A10 Installation And Operation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual