CCW06B10A
CCW08B10A
CCW10B10A
CCW12B10A
CEW08B11A
CEW12B33A
INTRODUCTION
IMPORTANT SAFETY INSTRUCTION ...........................................................................
ELECTRICAL REQUIREMENTS
PACKING LIST ............................................................................................................
INSTALLATION&ASSEMBLY INSTRUCTIONS ..............................................................
THROUGH-THE-WALL INSTALLATION INSTRUCTIONS................................................
USING YOUR AIR CONDITIONER ................................................................................
OPERATING YOUR AIR CONDITIONER
CARE AND CLEANING ................................................................................................
TROUBLESHOOTING .................................................................................................
...................................................................................
........................................................................
1
2
3
4
10
11
13
14
15
1
(6K cooling) 10A time-delay fuse or
circuit breaker
(8K-12K cooling & 8K heating) 15A
time-delay fuse or circuit breaker
(12K heating) 20A time-delay fuse or
circuit breaker
6K/8K/10K/12K Cooling
8K Heating
12K Heating
2
3/8" Short Screws
5
1/2" Length Screws
3/4" Long Screws
5/8" Big Flat Head Bolt and
Locknut
Sill Angel Bracket
1/2" Small Flat Head Bolt and
Locknut
Chassis Lock
Support Bracket(with R and L
remark)
Battery
3
4
3
2
4
ALL INFORMATION AND THE TECHNICAL SPECIFICATIONS PRESENTED IN THIS USER’ S MANUAL ARE THE PRESENTATION
OF THE MANUFACTURE. PLEASE READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY.
Window preparation
1. This air conditioner is designed to be installed
In a standard double-hung window with a window
width between 23” and 36” (660mm-914mm).
2. The air conditioner can be installed without the
accordion panels fit in a narrow window opening.
3. The lower sash ( the lower part of the window that
moves up and down) must allow for 16” of vertical
clearance when open.
4. All supporting parts must be secured to firm wood,
INTERIOR
WALL
STOOL
SILL
Air conditioner
OFFSET
Bottom channel
EXTERIOR
WALL
16”
406mm
23” to 36”
660mm to 914mm
masonry, or metal.
5. The electrical outlet must be within reach of the
power cord.
How to Install
NOTE:This is necessary for proper condensed water
utilization and drainage. If you are not using the Side
Panels for any reason, this pitch to the rear muse be
maintained!
Remove the air conditioner from the box and place on a
hard flat surface, as floor, a bench or a table. There is a
Left and Right Window Filler Panel - be sure to use the
proper panel for each side. When installed the flange for
securing the panel in place to the window sill will be facing
into the room.
4
REMOVE FRONT PANEL AND CHASSIS
1. Pull down the front panel and remove the filter.
2. Lift the front panel upwards to remove and place
to the side.
5. Remove the control panel screw and WI-FI module
screw (if available) from the front panel.
3. Locate the two faceplate screws and remove.
These screws will need to be re-installed prior
to mounting the air conditioner.
4. After removing the screws, gently pull away the
faceplate from the air conditioner cabinet.
6.Remove the screws from the cabinet.
7. Hold the cabinet while pulling on the base
handle to carefully remove the unit. Do not pull
or lift near the top of the unit.
Do not pull or lift
this area. It may
cause damage.
Pull the base handle.
5
Top Rail Assembly
1. Place the cabinet on a hard flat surface.
2. Remove top rail from the top form of the packaging
material as shown in FIG. A.
3. Align the hole in the top rail with those on the top of
the unit as shown in FIG. B.
4. Secure the top rail to the unit with the 3/8” screws
as shown in FIG. C.
Top RailTop Foam
6
Accordion Panel and cabinet Assembly
1.Hold the Accordion Panel in one hand and gently
pull the center to free the open end.
2.Slide the free end of the panel into the cabinet as
shown. Be sure to leave enough space to slip the
top and bottom of the frame into the rails on the
cabinet.
3.Once the panel has been installed on the side of
the cabinet, make sure it sits securely inside the
frame channel by making slight adjustments. Slide
the top and bottom ends of the frame into the top
and bottom rails of the cabinet. Slide the panel all
the way for both sides.
4.Use two or more people, place the air conditioner
into the window opening so the bottom of the air
conditioner frame is against the window sill.
Tilt the back of the unit slightly download to allow
accumulated rain water to drain out.
Air conditioner
INTERIOR
WALL
STOOL
SILL
OFFSET
Bottom channel
EXTERIOR
WALL
5.Fasten cabinet bottom to window sill using two
1/2” screws. Pre-drill holes if needed.
7
1.Hold each support bracket flush against the outside of
the window sill. Tighten each bracket to the bottom of the
cabinet as shown. Mark the brackets at top lever of the
window sill and then remove.
Sign marking
2.Assemble the sill angle brackets to the support
brackets at the marked position with long bolt and
locknut as shown. Hand tighten, but not all the way
for any changes that may need to be made later
during installation.
Support bracket
Bolt and
Locknut
Sill angle bracket
4. Tighten all the bolts with locknuts securely.
1.Team lift (two people or more) the air conditioner
chassis and carefully slide it into the cabinet. Let
the front of the air conditioner hang out
approximately 6”.
2.CAUTION: DO NOT PUSH ON THE CONTROLS
OR FINNED COILS.
Sill angle
bracket
1/2” long bolt
and locknut
5/8” long bolt
and locknut
3.Install the support brackets (with sill angle bra ckets) to the bottom of the cabinet as shown.
3.Be sure the chassis is firmly seated in the back of
the cabinet.
4.Insert all screws removed during window install ation and fasten, then reattach the front face plate,
front panel, and the air filter.
5. If the wall is too near to effect driving the cabinet
screw back, you can assemble the chassis lock at
the right bottom corner of chassis with 3/8” screw
as shown, before assemble the front panel.
Chassis Lock
8
5.Extend the side accordion panels out against
the window frame as shown.
7.To secure lower sash in place, attach right angle
sash lock with 3/4” screws as shown.
Sash lock
6.Drive 1/2” locking screws through frame holes,
and drive one 3/4” screw through top rail into
8.Cut foam seal and insert in the space between
the upper and lower sashes as shown.
window sash as shown.
Window seal
sponge
A storm window frame will not allow the air conditioner to tilt properly which in turn will keep it from draining
properly. To adjust for this, attach a board or piece of wood to the sill. The board or wood piece should have
a depth of at least 1/2”. Make sure the board or piece of wood is approximately 1/2” higher than the storm
window frame. This will allow the air conditioner to tilt enough for proper drainage.
SASH
16£¢MIN
1/2£¢MIN
1/2£¢MIN
SASH
16£¢MIN
1/2£¢MIN
Storm Window Frame or Obstruction
Storm Window Frame
or Obstruction
9
THROUGH-THE-WALL INSTALLATION INSTRUCTIONS - OPTIONAL
The case may be installed through-the-walll as optional.
Read completely, then follow step-by-step.
NOTE: Obtain all materials locally for mounting the air
conditioner through-the-wall.
IMPORTANT
Building a wooden frame is required when install the case
through-the-wall. The opening and dimension of wooden
frame is required as below.
Frame Max. Thickness
Inside Frame Width
Inside Frame Height
8 9/10”( 225 mm)
20”( 508 mm)
15-1/5”(385 mm)
Frame
Thickness
Inside
Frame
Height
Inside
Frame
Width
The Maximum
Wall thickness
8 9/10”(225mm)
NOTE: The allowed maximum wall thickness is less than
8 9/10”. Otherwise, the wall will block the air inlet of
outdoor side, it will effect the normally operation of unit.
1.Build a wooden frame into the wall opening and make
sure fasten securely, which is suitable to the WALL
OPENING REQUIREMENT.
2.Remove the air conditioner from the carton box and
take off the chassis as window mounting installation.
3.Place the cabinet into the wooden frame, and lock the
cabinet by the top rail hole and bottom chassis hole with
1” long wood screws as shown, from inside to outside.
4. Assemble the two Support Bracket with Sill Angle
Bracket to the cabinet against to the wooden frame as
window mounting installation instructions.
Through-the-wall installation is not appropriate, if any of
the side or top louvers of case is obstructed by the wall.
All side and top louvers in the case must project on the
outdoor side of the wall.
The room side of the case must project into the room far
enough to maximize the balance of the unit.
The case must be installed level from side to side and
with a slight tilt from front to rear. Use a level, no more
than a 1/2 bubble will be correct slant to the outside.
Lintel angle is required to support bricks or blocks
above opening.
Flashing is required and should extend the length of the
opening to ensure no inside cavity leakage occurs.
Support bracket
Bolt and
Locknut
Sill angle bracket
5. Assemble the chassis into the cabinet and fasten or
lock it, as window mounting installation instructions.
10
For Cooling model
For Heating model
1. Without timer setting, the set
Digital Display:
1
2
3
5
7
9
8
1
7
9
8
4
6
2
3
5
4
6
temperature will be displayed.
Time will be displayed under timer setting. the
+ and - Button:2. Use these buttons on the
control panel and remote to increase or decrease
the Set Temperature or Timer.
Temperature range: 61 ~88 or 16 ~31 .
3. Turn the air conditioner on and off.Button:
Press the mode button to cycle
4. Mode Button:
through the various modes: Cool, Dry, Fan and
Auto, or Heat.
Cool Mode: The cooling function allows the air
conditioner to cool the room and at the same time
reduces . Press the MODE button to
air humidity
activate the cooling function. To optimize the
function of the air conditioner, adjust the
temperature and the speed by pressing the button
indicated.
Dry Mode: This function reduces the humidity of
the air to make the room more comfortable. Press
MODE button to set the DRY mode. An automatic
function of alternating cooling cycles and air fan
is activated.
Fan Mode: The conditioner works in only
ventilation. Press MODE button to set the FAN
mode. With pressing FAN SPEED button the
the
speed changes in the following sequence: Hi, Med
and Lo in FAN mode.
Auto Mode: In AUTO mode the unit automatically
chooses the fan speed and the mode of operation
(COOL,HEAT,DRY or FAN). In this mode the
temperature are set automatically according to
the room temperature (tested by the temperature
sensor which is incorporated in the indoor unit.).
Heat Mode: The heating function allows the air
conditioner to heat the room. Press the MODE
button to activate the heating function. To optimize
the function of the air conditioner, adjust the
temperature and the speed by pressing the button
indicated.
Use these buttons on the control
5. Timer Button:
panel and remote to set the Timer.
Timer Off: The timed stop is programmed by
pressing TIMER button. Set the rest time by
pressing the button + or - until the rest
time displayed is to your then press
the
TIMER button again.
liking
Timer On: When the unit is off, press TIMER
button at the first time, set the temperature with
pressing the button + or - . Press TIMER
button at the second time, set the rest time with
pressing the button + or - . Press TIMER
button at the third time, confirm the setting, then
the rest time to next automatical switching-on
could be read on the display of the machine.
Note: It can be set to automatically turn off or on in
0.5-24 hours. Each press of the +-
buttons will increase or decrease the timer. The
Timer can be set in 0.5 hours increment below 10
hours and 1 hour increment for 10 hours or above.
The SET light will turn on while setting.
To cancel the set function, press the TIMER
button again.
11
When the unit is in Money
6. Money Saver Button:
Saver mode, the light will turn on. In Money Saver
mode, the unit will turn-off once the room is cooled
to the user set temperature. The unit will turn back
on when the room temperature rises above the
user set temperature. Before the compressor
, the fan motor will run for a while, starts then it will
stop for a while., It will repeat to provide a much
more comfortable feeling and save energy.
Press the SLEEP button, all the
7. Sleep Button:
display lights will turn off after a while, but the
SLEEP light is always on. In SLEEP mode, the air
conditioner will automatically adjust the temperature and fan speed to make the room more comfortable during the night. The set temperature will
automatically change every 30-60 minutes and at
most change six times until the setting temperature is 81ºF or 82ºF for cooling mode and 75ºF or
76ºF for heating mode.
Press the FAN SPEED button
8. Fan Speed Button:
to choose the fan speed options. You can choose
Hi, Med, Lo or auto speed in COOL or HEAT mode
and choose Hi, Med, Lo in FAN mode.
10.
To direct the airflow,
Directional Louvers:
horizontal wheel to control the horizontal direction,
air deflector to control the vertical direction.
horizontal wheelair deflector air deflector
9.
When the Filter Check light is off,
Filter Button:
it is useless to press the Filter Check button.
When the Filter Check light is on, it can turn off the
light by pressing the Filter Check button. After the
fan motor works for 500 total hours, the Filter
Check light will turn on to remind the user to clean
the filter.
12
1. Power: Turn the air conditioner on and off. This button will
clear the TIMER setting.
2. MODE: Press the button to select the mode of operation, AUTO, COOL,
DRY, FAN ONLY, HEAT.
Note: The HEAT mode is only for some heating models. If you do not
need it, press the MODE button for more than 5 seconds to delete the
HEAT function, and the COOL mode will be selected automatically.
Press the MODE again for more than 5 seconds to add the HEAT
function, and the HEAT mode will be selected automatically.
3. And : Use these buttons to increase or decrease the setting
Temperature or Timer. Setting temperature range: 61 ~88 or 16 ~31 .
Note: When the remote controller is turn-off, press and buttons can
pre-set the temperature. After the setting, the remote temperature display
will be off after a while.
4. TURBO: When the remote is ON, press the button to active the TURBO
function, under AUTO/COOL/FAN ONLY mode. Press again to cancel the
TURBO function, and the fan speed will change to pre-setting before.
Note: and change: After insert the batteries, in the off state within 3
minutes, press the TURBO button for more than 5 seconds to switch the
1
9
8
7
Fahrenheit ( ) or Celsius ( ) degree display.
2
5. DISPLAY: When the unit is ON, press the button, to switch off/on all lights
or LED display. And this function will be canceled when changing mode.
33
6. TIMER: Use the button to set the TIMER, or cancel the TIMER.
TIMER OFF: When the unit is ON, the timed OFF is programmed by
pressing TIMER button, the remote will display 6 hours pre-setting at first.
Set the rest time by pressing the button or until the needed rest time
4
display, then press TIMER button again to confirm.
TIMER ON: When the unit is OFF, the timed ON is programmed by pressing
TIMER button, the remote will display 6 hours pre-setting at first. Set the
5
rest time by pressing the button or until the needed rest time display,
then press TIMER button again to confirm. Later, the remote screen will keep
display [TIMER] icon.
6
Note: When TIMER ON, it cannot select Sleep mode, but can pre-set Mode,
temperature, fan speed, MONEY SAVER.
7. SLEEP: Press the SLEEP button, all of the display lights will turn off after a
while, but the Sleep light is always on. In SLEEP mode, the air conditioner
will automatically adjust the temperature and fan speed to make the room
more comfortable. The set temperature will automatically change every 30 60 minutes and at most change six times until the setting temperature is 81
or 82 for cooling mode and 75 or 76 for heating mode..
8. FAN SPEED: Press the FAN SPEED button to choose the fan speed options.
You can choose Hi, Med, Lo or Auto speed in COOL or HEAT mode and
choose Hi, Med, Lo in FAN mode. When DRY mode, it is only Low fan speed.
9. MONEY SAVER: When the unit is in COOL mode, press the button to
MONEY SAVER function. In MONEY SAVER mode, the unit will turn off
once the room is cooled to the user set temperature. The unit will turn back
on when the room temperature rises above the user set temperature. Before
the compressor starts, the fan motor will run for a while, then it will stop for
a while, and will repeat to provide a much more comfortable feeling and
save energy.
10. Child Lock: pressing the button or for more than 2 seconds to lock
or unlock the remote controller. When locked, each function button is no
useful, and the lock icon will flash when press any button.
-
+
-
+
-
+
-
+
-
+
13
15
FIG. 15
14
15
16
Loading...