Chill® Premier Series
Room Air Conditioners
Installation and Operation Manual
Standard Chassis Models Using R-32 Refrigerant
®
Chill® Premier
CCF10B10B, CCF12B10B, CCF14B10B
93071100_02
COOL ON LY
THE EXPERTS IN ROOM AIR CONDITIONING
115 VOLT CCF05B10B, CCF06B10B, CCF08B10B
CAUTION: Do Not Operate Equipment During Active Stages Of Construction
To ensure proper operation, Friedrich requires that all equipment is not operated during active construction phases. This includes active
stages of completing framing, drywalling, spackling, sanding, painting, flooring, and molding in the equipment’s designated conditioning space.
The use of this equipment during construction could result in premature failure of the components and/or system and is in violation of our
standard warranty guidelines. The operation of newly installed equipment during construction will accelerate the commencement and/or
termination of the warranty period.
Register your Air Conditioner
Model information can be found on the name plate.
Please complete and mail the owner registration card furnished
with this product, or register online at www.friedrich.com.
A. IMPORTANT SAFETY AND GENERAL INFORMATION
A.1 Introduction ...................................................................3
A.2 Safety Warnings ...........................................................3
A.3 Warning For Using R32 Refrigerant ..........................5
A.4 Importance of a Quality Installation ...........................7
A.5 Product Inspection / Packing List ..............................8
B. SPECIFICATIONS
B.1 Dimensions ....................................................................9
C. INSTALLATION OF THE UNIT
C.1 Pre-Installation Checkpoints.................................... 10
C.2 Tools Required .......................................................... 10
C.3. Choosing a Location ................................................. 10
C.4 Window Installation................................................... 11
For your future convenience, record the model information .
Model Number ________________________
Serial Number ________________________
E. ELECTRICAL
E.1 Electrical Safety Information ............................... 16
J. STARTUP AND OPERATION
J.1 Control Panel Operation ............................................ 17
J.2 Remote Control Operation ....................................... 19
J.3 Start-up ....................................................................... 20
L. WIFI
M. TROUBLESHOOTING
M.1. Troubleshooting Tips ............................................ 21
R . INFORMATION FOR THE OWNER
R.1 Routine Maintenance ................................................ 23
2
A. IMPORTANT SAFETY AND GENERAL INFORMATION
A.1 Introduction
This booklet contains the installation and operating instructions for your Air Conditioning unit. There are some precautions that should be taken
to ensure proper operation. Improper installation can result in unsatisfactory operation or dangerous conditions.
Read this booklet and any instructions packaged with separate equipment required to make up the system prior to installation. Give this booklet
to the owner and explain its provisions. The owner should retain this booklet for future reference.
A.2 Safety Warnings
WARNING: The manufacturer’s warranty does not cover
any damage or defect to the air conditioner caused by the attachment
or use of any components, accessories or devices (other than those
authorized by the manufacturer) into, onto or in conjunction with the
air conditioner. You should be aware that the use of
unauthorized components, accessories or devices may
adversely affect the operation of the air conditioner
and may also endanger life and property. The
manufacturer disclaims any responsibility for such loss
or injury resulting from the use of such unauthorized
components, accessories or devices.
WARNING: Electrical Shock Hazard
Disconnect all power to the unit before starting maintenance. All
electrical connections and wiring MUST be installed by a qualified
electrician and conform to the National Code and all local codes
which have jurisdiction. Failure to do so can result in property
damage, severe electrical shock or death.
WARNING ADVERTENCIA ATTENTION
WARNING: Read Installation Manual
Please read this manual thoroughly prior to
equipment installation or operation. It is the
installer’s responsibility to properly apply and
install the equipment. Installation must be in
conformance with the NFPA 70-2023 national
electric code or current edition, International
Mechanic code 2021 or current edition, and any
other local or national codes.
WARNING: Safety First
Do not remove, disable, or bypass this unit’s safety devices. Doing so
may cause fire, injuries, or death.
• RISK OF FIRE OR
EXPLOSION
• FLAMMABLE REFRIGERANT
USED
• REPAIRS MAY ONLY BE
PERFORMED BY TRAINED
PERSONNEL
• CONSULT SERVICE
MANUAL BEFORE
ATTEMPTING REPAIRS. ALL
SAFETY PRECAUTIONS MUST
BE FOLLOWED
• DO NOT PUNCTURE
TUBING
• DISPOSE OF UNIT
PROPERLY IN ACCORDANCE
WITH FEDERAL OR LOCAL
REGULATIONS
• ONLY USE A2L APPROVED
SERVICE EQUIPMENT
• RIESGO DE FUEGO
• REFIGERANTE INFLAMABLE
UTILZADO
• PARA SER REPARDO
UNICAMENTE POR PERSONAL
DE SERVICIO CAPACITADO
• CONSULTE EL MANUAL
DE REPARACION DEL
PROPIETARIO ANTES
DE INTENTAR REPARAR
ESTE PRODUCTO. SE
DEBEN SEGUIR TODAS
LAS PRECAUCIONES DE
SEGURIDAD
• NO PERFORE LA TUBERIA
DE REFRIGERANTE
• DESECHE
APROPIADAMENTE DE
ACUERDO CON LAS
REGULACIONES FEDERALES
O LOCALES
• RISQUE D’INCENDIE
• REFRIGERANT
INFLAMMABLE UTILISE
• A REPARER UNIQUEMENT
PAR DU PERSONNELDE
SERVICE QUALIFIE
• CONSULTAR LE MANUEL
DE REPARATION/GUIDE
DU PROPRIETARE AVANTE
DE TENTER DE REPARER
CE PRODUIT. TOUTES LES
PRECAUTIONS DE SECURITE
DOIVENT ETRE SUIVIES
• NE PAS PERFORER LE
TUYAU DE REFRIGERANT
• ELIMINER CORRECTEMENT
CONFORMENT AUX
REGLEMENTS FEDERAUX OU
LOCAUX
3
A. IMPORTANT SAFETY AND GENERAL INFORMATION
Read All Instructions and Cautionary Markings Before Operation
and Installation to prevent death or injury to the user, other people,
or property damage, the following instructions must be followed.
Incorrect operation due to ignoring of instructions may cause death,
harm or damage.
18. After proper installation, condensate will not overflow during
normal use. If the fan hits the built-up water and the sound annoys
you, please remove the cap located at the back of the air conditioner
to drain the water away.
WARNING: This symbol indicates the possibility of a
hazard to personnel.
CAUTION: This symbol indicates the possibility of
property damage or serious consequences.
WARNING:
1. Installation must be performed according to the installation
instructions. Improper installation can cause water leakage, electrical
shock, or fire.
2. Use only the included accessories and parts, and specified tools for
the installation. Using nonstandard parts can cause water leakage,
electrical shock, fire, and injury or property damage.
3. Make sure that the outlet you are using is grounded and has the
appropriate voltage. The power cord is equipped with a three-prong
grounding plug to protect against shock. Voltage information can be
found on the nameplate of the appliance.
4. Your appliance must be used in a properly grounded wall
receptacle. If the wall receptacle you intend to use is not adequately
grounded or protected by a time delay fuse or circuit breaker (the
fuse or circuit breaker needed is determined by the maximum current
of the appliance. The maximum current is indicated on the model
nameplate located on the appliance, have a qualified electrician install
the proper receptacle.
5. Install the appliance on a flat, sturdy surface. Failure to do so could
result in damage or excessive noise and vibration.
6. The appliance must be kept free from obstruction to ensure proper
function and to mitigate safety hazards.
7. The unit should not be in contact with any equipment that will
transmit vibration to the unit. Any excessive vibration or pulsation to
the unit could result in damage to the refrigerant tubing.
8. Do not modify the length of the power cord or use an extension
cord to power the appliance.
9. Do not share a single outlet with other electrical appliances.
Improper power supply can cause fire or electrical shock.
10. Do not install your air conditioner in a wet room such as a
bathroom or laundry room. Too much exposure to water can cause
electrical components to short circuit.
11. Do not install the appliance in a location that may be exposed to
combustible gas, as this could cause fire.
12. Do not operate the appliance if it has been dropped or damaged.
13. Do not touch the appliance with wet or damp hands or when
barefoot.
14. If the air conditioner is knocked over during use, turn off the
appliance and unplug it from the main power supply immediately.
Visually inspect the appliance to ensure there is no damage. If you
suspect the appliance has been damaged, contact a technician or
customer service for assistance.
15. In a thunderstorm, the power must be cut off to avoid damage
to the machine due to lightning. Your air conditioner should be used
in such a way that it is protected from moisture. e.g. condensation,
splashed water, etc. Do not place or store your air conditioner
where it can fall or be pulled into water or any other liquid. Unplug
immediately if it occurs.
16. All wiring must be performed strictly in accordance with the
wiring diagram located inside of the appliance.
17. The appliance’s circuit board(PCB) is designed with a fuse to
provide overcurrent protection. The specifications of the fuse are
printed on the circuit board, such as: T 3.15A/250V, etc.
4
CAUTION:
1. This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person
responsible for their safety. Children should be supervised to ensure
that they do not play with the appliance. Children must be supervised
around the appliance at all times.
2. If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in order
to avoid a hazard.
3. Prior to cleaning or other maintenance, the appliance must be
disconnected from the supply mains.
4. Never use this appliance if it is not working properly, or if it has
been dropped or damaged.
5. Do not run cord under carpeting. Do not cover cord with throw rugs,
runners, or similar coverings. Do not route cord under furniture or
appliances. Arrange cord away from traffic area and where it will not
be tripped over.
6. Do not operate with a damaged cord, plug, power fuse or circuit
breaker. Discard the appliance or return to an authorized service
facility for examination and/or repair.
7. To reduce the risk of fire or electric shock, do not use this fan with
any solid-state speed control device.
8. The appliance shall be installed in accordance with national wiring
regulations.
9. Contact the authorized service technician for repair or maintenance
of this appliance.
10. Contact the authorized installer for installation of this appliance.
11. Do not cover or obstruct the inlet or outlet grilles.
12. Do not use this product for functions other than those described in
this instruction manual.
13. Before cleaning, turn off the power and unplug the appliance.
14 .Disconnect the power if strange sounds, smell, or smoke comes
from it.
15. Do not press the buttons on the control panel with anything other
than your fingers.
16. Do not operate or stop the appliance by inserting or pulling out the
power cord plug.
17. Do not use hazardous chemicals to clean or come into contact with
the appliance.
18. Do not use the appliance in the presence of flammable substances
or vapor such as alcohol, insecticides, petrol,etc.
19. Always contact a qualified person to carry out repairs. If the power
supply cord is damaged, it must be replaced with a new power supply
cord obtained from the product manufacturer and not repaired.
20. Hold the plug by the head of the power plug when taking it out.
21. Turn off the product when not in use.
A. IMPORTANT SAFETY AND GENERAL INFORMATION
A.3 Warning For Using R32 Refrigerant
For R32 refrigerant models:
1. Appliance shall be installed, operated and stored in a room with a
floor area larger than 43 sq ft.
2. Appliance shall not be installed in an unventilated space, if that
space is smaller than 43 sq ft.
3. Compliance with national gas regulations shall be observed.
4. Keep ventilation openings clear of obstruction.
5. The appliance shall be stored so as to prevent mechanical damage
from occurring.
6. A warning that the appliance shall be stored in a well-ventilated
area where the room size corresponds to the room area as specified
for operation.
7. Any person who is involved with working on or opening a
refrigerant system must be certified for refrigerant handling as
required by local, state, and federal regulations.
8. Servicing shall only be performed as recommended by the
equipment manufacturer. Maintenance and repair requiring the
assistance of other skilled personnel shall be carried out under
the supervision of the person competent in the use of flammable
refrigerants.
9. Please follow the instruction carefully to handle, install, clear, and
service the air conditioner to avoid any damage or hazard. Flammable
Refrigerant R32 is used within air conditioner. When maintaining or
disposing the air conditioner, the refrigerant (R32) shall be recovered
properly, and shall not be discharged to air directly.
10. No any open fire or device like a switch which may generate
spark/arcing shall be around the air conditioner to avoid causing
ignition of the flammable refrigerant used.
11. Please follow the instruction carefully to store or maintain the air
conditioner to prevent mechanical damage from occurring.
12. Flammable refrigerant R32 is used in air conditioner. Please
follow the instruction carefully to avoid any hazard.
13. For specific information on the type of gas and the amount of
refrigerant used, refer to the model nameplate on the unit.
CAUTION: Risk of fire/flammable materials
(Required for R32 units only)
WARNING: low burning velocity material
(For R32 models apply to IEC60335-2-40:2018)
Note about Fluorinated Gases
1. Fluorinated greenhouse gases are contained in hermetically sealed
equipment. For specific information on the type, the amount and the
Co2 equivalent in tonnes of the fluorinated greenhouse gas(on some
models), please refer to the relevant label on the unit itself.
2. Installation, service, maintenance and repair of this unit must be
performed by a certified technician.
3. Product de-installation and recycling must be performed by a
certified technician.
For Household Use Only Read And Save These Instructions
1. Transport of equipment containing flammable refrigerants:
See transport regulations.
2. Marking of equipment using signs:
See local regulations.
3. Disposal of equipment using flammable refrigerants:
See national regulations.
4. Storage of equipment/appliances:
The storage of equipment should be in accordance with the
manufacturer’s instructions.
5. Storage of packed (unsold) equipment:
Storage package protection should be constructed such that
mechanical damage to the equipment inside the package will not
cause a leak of the refrigerant charge. The maximum number
of pieces of equipment permitted to be stored together will be
determined by local regulations.
6. Information on servicing:
1) Checks to the area:
Prior to beginning work on systems containing flammable
refrigerants, safety checks are necessary to ensure that the risk
of ignition is minimized. For repair to the refrigerating system, the
following precautions shall be complied with prior to conducting work
on the system.
2) Work procedure:
Work shall be undertaken under a controlled procedure so as to
minimize the risk of a flammable gas or vapour being present while
the work is being performed.
3) General work area:
All maintenance staff and others working in the local area shall be
instructed on the nature of work being carried out. Work in confined
spaces shall be avoided. The area around the workspace shall be
sectioned off. Ensure that the conditions within the area have been
made safe by control of flammable material.
4) Checking for presence of refrigerant:
The area shall be checked with an appropriate refrigerant detector
prior to and during work, to ensure the technician is aware of
potentially flammable atmospheres. Ensure that the leak detection
equipment being used is suitable for use with flammable refrigerants,
i.e. non-sparking, adequately sealed or intrinsically safe.
5) Presence of fire extinguisher:
If any hot work is to be conducted on the refrigeration equipment or
any associated parts, appropriate fire extinguishing equipment shall
be available to hand. Have a dry powder or CO2 fire extinguisher
adjacent to the charging area.
6) No ignition sources:
No person carrying out work in relation to a refrigeration system
which involves exposing any pipe work that contains or has contained
flammable refrigerant shall use any sources of ignition in such a
manner that it may lead to the risk of fire or explosion. All possible
ignition sources, including cigarette smoking, should be kept
sufficiently far away from the site of installation, repairing, removing
and disposal, during which flammable refrigerant can possibly be
released to the surrounding space. Prior to work taking place,
the area around the equipment is to be surveyed to make sure that
there are no flammable hazards or ignition risks. No Smoking signs
shall be displayed.
7) Ventilated area:
Ensure that the area is in the open or that it is adequately ventilated
before breaking into the system or conducting any hot work. A degree
of ventilation shall continue during the period that the work is carried
out. The ventilation should safely disperse any released refrigerant
and preferably expel it externally into the atmosphere.
8) Checks to the refrigeration equipment:
Where electrical components are being changed, they shall be fit
for the purpose and to the correct specification. At all times the
manufacturer’s maintenance and service guidelines shall be followed.
If in doubt consult the manufacturer’s technical department for
assistance. The following checks shall be applied to installations
using flammable refrigerants:
a. The charge size is in accordance with the room size within which
the refrigerant containing
parts are installed;
b. The ventilation machinery and outlets are operating adequately and
are not obstructed;
c. If an indirect refrigerating circuit is being used, the secondary
circuit shall be checked for the presence of refrigerant; Marking to
the equipment continues to be visible and legible. Markings and signs
that are illegible shall be corrected;
d. Refrigeration pipe or components are installed in a position
where they are unlikely to be exposed to any substance which may
corrode refrigerant containing components, unless the components
are constructed of materials which are inherently resistant to being
5
A. IMPORTANT SAFETY AND GENERAL INFORMATION
corroded or are suitably protected against being so corroded.
9) Checks to electrical devices:
Repair and maintenance to electrical components shall include
initial safety checks and component inspection procedures. If a fault
exists that could compromise safety, then no electrical supply shall
be connected to the circuit until it is satisfactorily dealt with. If the
fault cannot be corrected immediately but it is necessary to continue
operation, an adequate temporary solution shall be used. This shall
be reported to the owner of the equipment so all parties are advised.
Initial safety checks shall include:
a. That capacitors are discharged: this shall be done in a safe manner
to avoid possibility of sparking;
b. That there no live electrical components and wiring are exposed
while charging, recovering or purging the system;
c. That there is continuity of earth bonding.
7. Repair to intrinsically safe components:
Do not apply any permanent inductive or capacitance loads to the
circuit without ensuring that this will not exceed the permissible
voltage and current permitted for the equipment in use. Intrinsically
safe components are the only types that can be worked on while live
in the presence of a flammable atmosphere. The test apparatus shall
be at the correct rating.
Replace components only with parts specified by the manufacturer.
Other parts may result in the ignition of refrigerant in the atmosphere
from a leak.
8. Cabling:
Check that cabling will not be subject to wear, corrosion, excessive
pressure, vibration, sharp edges or any other adverse environmental
effects. The check shall also take into account the effects of aging or
continual vibration from sources such as compressors or fans.
9. Detection of flammable refrigerants
Under no circumstances shall potential sources of ignition be used in
the searching for or detection of refrigerant leaks. A halide torch (or
any other detector using a naked flame) shall not be used.
10. Leak detection methods:
The following leak detection methods are deemed acceptable for
systems containing flammable refrigerants. Electronic leak detectors
shall be used to detect flammable refrigerants, but the sensitivity may
not be adequate, or may need re-calibration. (Detection equipment
shall be calibrated in a refrigerant-free area.) Ensure that the detector
is not a potential source of ignition and is suitable for the refrigerant
used. Leak detection equipment shall be set at a percentage of the
LFL of the refrigerant and shall be calibrated to the refrigerant
employed and the appropriate percentage of gas (25 % maximum)
is confirmed. Leak detection fluids are suitable for use with most
refrigerants but the use of detergents containing chlorine shall be
avoided as the chlorine may react with the refrigerant and corrode
the copper pipe-work. If a leak is suspected, all naked flames shall
be removed/extinguished. If a leakage of refrigerant is found which
requires brazing, all of the refrigerant shall be recovered from the
system, or isolated (by means of shut off valves) in a part of the
system remote from the leak. Oxygen free nitrogen (OFN) shall then
be purged through the system both before and during the brazing
process.
11. Removal and evacuation
When breaking into the refrigerant circuit to make repairs or for any
other purpose conventional procedures shall be used. However, it
is important that best practice is followed since flammability is a
consideration. The following procedure shall be adhered to: Remove
refrigerant; Purge the circuit with inert gas; Evacuate; Purge again
with inert gas; Open the circuit by cutting or brazing. The refrigerant
charge shall be recovered into the correct recovery cylinders.
The system shall be flushed with OFN to render the unit safe. This
process may need to be repeated several times. Compressed air or
oxygen shall not be used for this task. Flushing shall be achieved by
6
breaking the vacuum in the system with OFN and continuing to fill
until the working pressure is achieved, then venting to atmosphere,
and finally pulling down to a vacuum. This process shall be repeated
until no refrigerant is within the system. When the final OFN charge
is used, the system shall be vented down to atmospheric pressure to
enable work to take place. This operation is absolutely vital if brazing
operations on the pipe-work are to take place. Ensure that the outlet
for the vacuum pump is not close to any ignition sources and there is
ventilation available.
12. Charging procedures:
In addition to conventional charging procedures, the following
requirements shall be followed. Ensure that contamination of different
refrigerants does not occur when using charging equipment. Hoses
or lines shall be as short as possible to minimize the amount of
refrigerant contained in them. Cylinders shall be kept upright. Ensure
that the refrigeration system is earthed prior to charging the system
with refrigerant. Label the system when charging is complete (if not
already). Extreme care shall be taken not to overfill the refrigeration
system. Prior to recharging the system it shall be pressure tested
with OFN. The system shall be leak tested on completion of charging
but prior to commissioning. A follow up leak test shall be carried out
prior to leaving the site.
13. Decommissioning:
Before carrying out this procedure, it is essential that the technician
is completely familiar with the equipment and all its detail. It is
recommended good practice that all refrigerants are recovered safely.
Prior to the task being carried out, an oil and refrigerant sample shall
be taken in case analysis is required prior to re-use of reclaimed
refrigerant. It is essential that electrical power is available before the
task is commenced.
a. Become familiar with the equipment and its operation.
b. Isolate system electrically.
c. Before attempting the procedure ensure that: Mechanical handling
equipment is available, if required, for handling refrigerant cylinders;
All personal protective equipment is available and being used
correctly; The recovery process is supervised at all times by a
competent person; Recovery equipment and cylinders conform to the
appropriate standards.
d. Pump down refrigerant system, if possible.
e. If a vacuum is not possible, make a manifold so that refrigerant can
be removed from various parts of the system.
f. Make sure that cylinder is situated on the scales before recovery
takes place.
g. Start the recovery machine and operate in accordance with
manufacturer’s instructions.
h. Do not overfill cylinders. (No more than 80 % volume liquid charge).
i. Do not exceed the maximum working pressure of the cylinder, even
temporarily.
j. When the cylinders have been filled correctly and the process
completed, make sure that the cylinders and the equipment are
removed from site promptly and all isolation valves on the equipment
are closed off.
k. Recovered refrigerant shall not be charged into another
refrigeration system unless it has been cleaned and checked.
14. Labeling:
Equipment shall be labeled stating that it has been de-commissioned
and emptied of refrigerant. The label shall be dated and signed.
Ensure that there are labels on the equipment stating the equipment
contains flammable refrigerant.
15. Recovery:
When removing refrigerant from a system, either for servicing
or decommissioning, it is recommended good practice that all
refrigerants are removed safely. When transferring refrigerant into
cylinders, ensure that only appropriate refrigerant recovery cylinders
are employed. Ensure that the correct number of cylinders for holding
A. IMPORTANT SAFETY AND GENERAL INFORMATION
the total system charge is available. All cylinders to be used are designated for the recovered refrigerant and labeled for that refrigerant (i.e.
special cylinders for the recovery of refrigerant).
Cylinders shall be complete with pressure relief valve and associated shut-off valves in good working order. Empty recovery cylinders are
evacuated and, if possible, cooled before recovery occurs. The recovery equipment shall be in good working order with a set of instructions
concerning the equipment that is at hand and shall be suitable for the recovery of flammable refrigerants. In addition, a set of calibrated
weighing scales shall be available and in good working order. Hoses shall be complete with leak-free disconnect couplings and in good
condition. Before using the recovery machine, check that it is in satisfactory working order, has been properly maintained and that any
associated electrical components are sealed to prevent ignition in the event of a refrigerant release. Consult manufacturer if in doubt. The
recovered refrigerant shall be returned to the refrigerant supplier in the correct recovery cylinder, and the relevant Waste Transfer Note
arranged. Do not mix refrigerants in recovery units and especially not in cylinders. If compressors or compressor oils are to be removed,
ensure that they have been evacuated to an acceptable level to make certain that flammable refrigerant does not
remain within the lubricant. The evacuation process shall be carried out prior to returning the compressor to the suppliers. Only electric
heating to the compressor body shall be employed to accelerate this process. When oil is drained from a system, it shall be carried out safely.
NOTE: Check the appliance regularly and refer to TROUBLESHOOTING or contact our customer support if it shows any of the following signs:
- Power cord or plug is damaged.
- Loud noise, unusual smell or excessive heat.
A.4 Importance of a Quality Installation
Optimal system performance and longevity depend upon a quality and proper installation. Failure to properly install this unit could result in
undesirable operation and subsequent faults and potential failures.
Carefully follow all guidelines listed in the manual and industry best practices. Conform to all local code requirements. Contact your local
technical representative with any questions or concerns.
7
A. IMPORTANT SAFETY AND GENERAL INFORMATION
A.5 Product Inspection / Packing List
Upon receiving the unit, inspect it for any damage from shipment. Claims for damage, either shipping or concealed, should be filed
immediately with the shipping company. IMPORTANT: Check the unit model number, Cooling size, electrical characteristics, and
accessories to determine if they are correct.
Figure A.4 (Packing List)
8
B. SPECIFICATIONS
2. PRODUCT DIMENSIONS
Air Conditioner Service Manual
B.1 Dimensions
Window type:
Model A (Width) B (Height) C (Depth)
CCF05B10B, CCF06B10B,
CCF08B10B
CCF10B10B
CCF12B10B, CCF14B10B
18
18
19
5
5
3/4
/8
/8
13
13
15
Figure B.1
Dimensions In Inches
3
/8
3
/8
1/8
15
17
21
5
3
/8
1/2
MINIMUM
WINDOW
WIDTH
/8
23 36
MAXIMUM
WINDOW
WIDTH
23 36
26 36
9
C. INSTALLATION OF THE UNIT
3
C.1 Pre-Installation Checkpoints
Before attempting any installation, carefully consider the
following points:
• Clearances and provision for servicing. Install this unit
in accordance with local and national standards. Any and
all work must be done by authorized personnel.
• IMPORTANT: Before you begin the actual installation
of your air conditioner, check your local electrical codes
and the information below. Your air conditioner must be
connected to a power source with the same alternating
current (A.C.) voltage and amperage as marked on the
name plate located on the chassis. Only A.C. can be used.
Direct Current (D.C.) cannot be used.
• CIRCUIT PROTECTION – Use on single outlet circuit only.
An overloaded circuit will invariably cause malfunction or
failure of an air conditioner; therefore, it is necessary that
the electrical protection is adequate. Due to momentary
high current demand when the air conditioner starts,
use a “TIME DELAY” fuse or a HACR type circuit breaker.
Consult your dealer or power company if in doubt.
• Refer to the electrical name plate located on the air
conditioner chassis (see Table E.1 to determine the
correct fuse or circuit breaker amperage for your model.
• The power cord has a plug with a grounding prong and a
matching receptacle is required.
C.2 Tools Required
WARNING
C.3. Choosing a Location
Installation Clearances
Improper installation of the Air Conditioner can cause poor
performance and premature wear of the unit.
Ensure that the unit is installed with proper clearances as described
below.
Ensure no obstructions or enclosures are within clearances limits to
allow for proper airflow.
Ensure no open flames, or surfaces that will exceed 1000 degrees
fahrenheit are within clearances limits.
WARNING
Refigeration System
Under High Pressure
Do not puncture, heat, expose to flame or
incinerate.
Only certified refrigeration technicians should
service this equipment.
R410A and R32 systems operate at higher
pressures than R22 equipment.
Appropriate safe service and handling
practices must be used.
Only use gauge sets designed for use with
R410A or R32.
Do not use standard R22 gauge sets..
Clearances
Top and Bottom of Unit - One (1) foot
Sides of Unit - One (1) foot
Front of Unit - Three (3) feet
Rear of Unit - Three (3) feet
1. Power Drill
1/8
2.
Drill Bit
3. Gloves
4. Carpenters Level
5. #2 Phillips Screw
Driver
6. Putty Knife or (wood
stir stick)
Electrical Shock Hazard
Make sure your electrical receptacle has the
same configuration as your air conditioner’s
plug. If different, consult a Licensed Electrician.
Do not use plug adapters.
Do not use an extension cord.
Do not remove ground prong.
Always plug into a grounded 3 prong outlet.
Failure to follow these instructions can result in
death, fire, or electrical shock.
4
1
2
5/16
5/16
1/4
WARNING
Fire Hazard
A2L refrigerant is classified as mildly
flammable. Do not install unit next open flame
sources, or surfaces that will exceed
1200 degrees fahrenheit.
1/4
65
87
10
C. INSTALLATION OF THE UNIT
(USED FOR 5K/6K/8K/10K)
(USED FOR 5K/6K/8K/10K)
(USED FOR 12K/14K)
C.4 Window Installation
CAUTION
Moving Parts Hazard
Do not operate unit out of sleeve
or with front grille removed.
Do not place hands in blower
or fan blade areas.
Failure to do so can result
in serious injury
C.4.1 General Information 5-10k Btu Units
CAUTION
Excessive Weight Hazard
Use two or more people when
installing your air conditioner.
Failure to do so can result in
back or other injury.
C.4.2 General Information 12-14k Btu Units
11
Window Installation(Cont)
C.4.3 Top Rail Assembly 8k BTU Units Only
C. INSTALLATION OF THE UNIT
12
C. INSTALLATION OF THE UNIT
Window Installation(Cont)
Besure that, there will be a 3 tilt angle
downward to the unit back side, after
finish the unit installation.
13
Window Installation(Cont)
C. INSTALLATION OF THE UNIT
14
C. INSTALLATION OF THE UNIT
Window Installation(Cont)
15
E.1 Electrical Safety Information
WARNING
Electrical Shock Hazard
Make sure your electrical receptacle has the
same configuration as your air conditioner’s
plug. If different, consult a Licensed Electrician.
Do not use plug adapters.
Do not use an extension cord.
Do not remove ground prong.
Always plug into a grounded 3 prong outlet.
Failure to follow these instructions can result in
death, fire, or electrical shock.
Make sure the wiring is adequate for your unit.
If you have fuses, they should be of the time delay type. Before you
install or relocate this unit, be sure that the amperage rating of the
circuit breaker or time delay fuse does not exceed the amp rating
listed in Table 1.
E. ELECTRICAL
E.2 Testing the Power Cord
All Friedrich room air conditioners are shipped from the factory
with a Leakage Current Detection Interrupter (LCDI) equipped power
cord. The LCDI device on the end of the cord meets the UL and NEC
requirements for cord connected air conditioners.
To test your power supply cord:
1. Plug power supply cord into a grounded 3 prong outlet.
2. Press RESET (see Figure E.2).
3. Press TEST, listen for click; the RESET button trips and pops out.
4. Press and release RESET (Listen for click; RESET button latches and
remains in). The power cord is ready for use.
Once plugged in, the unit will operate normally without the need to reset the
LCDI device. If the LCDI device fails to trip when tested or if the power supply
cord is damaged, it must be replaced with a new power supply cord from the
manufacturer..
RESET
DO NOT use an extension cord.
The cord provided will carry the proper amount of electrical power
to the unit; an extension cord may not.
Make sure that the receptacle is compatible with the
air conditioner cord plug provided.
Proper grounding must be maintained at all times. Two prong
receptacles must be replaced with a grounded receptacle by a certified
electrician.
The grounded receptacle should meet all national and local codes
and ordinances. You must use the three prong plug furnished with
the air conditioner. Under no circumstances should you remove the
ground prong from the plug.
Table E.1
MODEL
CCF05, CCF06, CCF08,
CCF10, CCF12, CCF14
CIRCUIT RATING
OR TIME DELAY
FUSE
AMP VOLT
15 125 5-15R
REQUIRED
WALL
RECEPTACLE
NEMA
NO.
TEST
WARNING:
TEST BEFORE EACH USE.
TO TEST:
PRESS RESET BUTTON.
PLUG LCDI INTO POWER
RECEPTACLE.
PRESS TEST BUTTON, RESET
BUTTON SHOULD POP UP.
PRESS RESET BUTTON FOR USE.
DO NOT USE IF TEST IS FAILED.
GREEN LIGHT INDICATES
PROPER OPERATION
Figure E.2
16
J.1 Control Panel Operation
J. STARTUP AND OPERATION
+-
to 73 degrees F. After placing the unit in auto mode,
restart the unit by pressing the power button to engage
the auto mode.
+-
+-
+-
+-
17
J. STARTUP AND OPERATION
J.1 Control Panel Operation (Cont)
18
J. STARTUP AND OPERATION
J.2 Remote Control Operation
1. Power: Turn the air conditioner on and off. This button will clear the TIMER setting.
2. MODE: Press the button to select the mode of operation, AUTO, COOL, DRY, FAN ONLY, HEAT.
Note: The HEAT mode is only for some heating models. If you do not need it, press the MODE button for
more than 5 seconds to delete the HEAT function, and the COOL mode will be selected automatically. Press
the MODE again for more than 5 seconds to add the HEAT function, and the HEAT mode will be selected
automatically.
3. + And - : Use these buttons to increase or decrease the setting Temperature or Timer. Setting
temperature range: 61 ~88°F.
Note: After setting temperature with remote using the + and - buttons, both the remote display
and the unit display will automatically turn off after a short time. This does not affect the unit
operation.
4. TURBO: When the remote is ON, press the button to activate the TURBO function, under
AUTO/COOL/FAN ONLY mode. Press again to cancel the TURBO function, and the fan speed will
change to pre-setting before.
Note: °F and °C change: After inserting the batteries, in the off state within 3 minutes, press
the TURBO button for more than 5 seconds to switch the Fahrenheit (°F) or Celsius (°C) degree
display.
5. DISPLAY: When the unit is ON, press the button, to switch off/on all lights or LED display. And
this function will be canceled when changing mode.
6. TIMER: Use the button to set the TIMER, or cancel the TIMER.
TIMER OFF: When the unit is ON, the timed OFF is programmed by pressing TIMER button, the
remote will display 6 hours pre-setting at first.
Set the rest time by pressing the button or until the needed rest time display, then press TIMER
button again to confirm.
TIMER ON: When the unit is OFF, the timed ON is programmed by pressing TIMER button, the
remote will display 6 hours pre-setting at first. Set the rest time by pressing the button or until
the needed rest time display, then press TIMER button again to confirm. Later, the remote screen
will keep display [TIMER] icon.
Note: When TIMER ON, it cannot select Sleep mode, but can pre-set Mode, temperature, fan
speed, ECO.
7. SLEEP: Press the SLEEP button, all of the display lights will turn off after a while, but the
Sleep light is always on. In SLEEP mode, the air conditioner will automatically adjust the temperature and fan speed to make the room more comfortable during the night. The set temperature will automatically raise every 30-60 minutes and at most change six times until the set
temperature is 81 or 82°F. This function can be selected when COOL or HEAT mode.
1
2
33
9
8
4
5
67
8. FAN SPEED: Press the FAN SPEED button to choose the fan speed options. You can choose Hi,
Med, Lo or Auto speed in COOL or HEAT mode and choose Hi, Med, Lo in FAN mode. When DRY
mode, it is only Low fan speed.
9. MONEY SAVER: When the unit is in COOL mode, press the button to MONEY SAVER function.
In MONEY SAVER mode, the unit will turn off once the room is cooled to the user set temperature. The unit will turn back on when the room temperature rises above the user set temperature. Before the compressor starts, the fan motor will run for 20 sec., then it will stop for 10
min., and will repeat to provide a much more comfortable feeling and save energy.
Battery size: AAA
Note: Do not mix old and new batteries or different types of AAA batteries.
19
J. STARTUP AND OPERATION
J.3 Start-up
This is a warm weather appliance
Your air conditioner is designed to cool in warm weather when the outside temperature is above 60 °F (15.6 °C) and below 115 °F (46.1 °C), so it won’t
cool a room if it is already cool outside.
Condensation is normal
Air conditioners actually pump the heat and humidity from your room to the outside. Humidity becomes water, and your air conditioner will use
most of the water to keep the outside coil cool. If there is excessive humidity, there may be excess water that will drip outside. This is normal
operation.
Frosting
This usually occurs because of insufficient airflow across the coils, a dirty filter, cool damp weather, or all these. Set the SYSTEM mode to FAN
ONLY and the frost will disappear. Setting the thermostat a little warmer will probably prevent the frosting from recurring.
Noises
All air conditioners make some noise. Friedrich units are designed to operate as quietly as possible. An air conditioner mounted in a wall is quieter
than one mounted in a window. It is important to ensure that the chassis seal gasket is properly installed (refer to the Installation Instructions).
L.
WiFi
Use a QR Reader on your phone to Scan this QR Code. It will take you to the Wifi Instructions page of our website..
FriedrichGo
20
M. TROUBLESHOOTING
M.1. Troubleshooting Tips
COMPLAINT CAUSE SOLUTION
Unit does not operate.
Unit Trips Circuit
Breaker or
Blows Fuses.
LCDI Power Cord Trips
(Reset Button Pops
Out).
Unit Does Not Cool
Room Sufciently, or
Cycles On And Off Too
Frequently.
Unit Does Not Cool
Room Sufciently, or
Cycles On And Off Too
Frequently (continued).
• The unit is turned to the off position, or the
thermostat is satised.
• The LCDI power cord is unplugged.
• The LCDI power cord has tripped (Reset
button has popped out).
• The circuit breaker has tripped or the supply
circuit fuse has blown.
• There has been a local power failure. • The unit will resume normal operation once power has been restored.
• Other appliances are being used on the same
circuit.
• An extension cord is being used. • Do NOT use an extension cord with this or any other air conditioner.
• The circuit breaker or time-delay fuse is not of
the proper rating.
• The LCDI power cord can trip (Reset button
pops out) due to disturbances on your
power supply line.
• Electrical overload, overheating, or cord
pinching can trip (Reset button pops out) the
LCDI power cord.
NOTE: A damaged power supply cord must be replaced with a new power supply cord obtained from the product manufacturer and
must not be repaired.
• The return/ discharge air grille is blocked.
• Windows or doors to the outside are open. • Ensure that all windows and doors are closed.
• The temperature is not set at a cool enough
enough setting.
• The lter is dirty or obstructed. • Clean the lter, (see Routine Maintenance), or remove obstruction.
• The indoor coil or outdoor coil is dirty or
obstructed.
• There is excessive heat or moisture
(cooking, showers, etc.) in the room.
• The temperature of the room you are trying
to cool is extremely hot.
• The outside temperature is below 60 °F
(16 °C).
• The digital control is set to fan cycling mode.
• The air conditioner has insufcient cooling
capacity to match the heat gain of the room.
• The air conditioner has insufcient heating
capacity to match the heat loss of the room.
• Turn the unit to the on position and raise or lower temperature setting (as
appropriate) to call for operation.
• Plug into a properly grounded 3 prong receptacle. See “Electrical Rating
Tables” on Page 6 for the proper receptacle type for your unit.
• Press and release RESET (Listen for click. Reset button latches and
remains in.) to resume operation.
• Reset the circuit breaker, or replace the fuse as applicable. If the
problem continues, contact a licensed electrician.
• The unit requires a dedicated outlet circuit, not shared with other appliances.
• Replace with a circuit breaker or time-delay fuse of the proper rating. See
“Electrical Rating Tables” on Page 6 for the proper circuit breaker/ fuse rating
for your unit. If the problem continues, contact a licensed electrician.
• Press and release RESET (Listen for click. Reset button latches and
remains in.) to resume normal operation.
• Once the problem has been determined and corrected, press and
release RESET (Listen for click. Reset button latches and remains in.)
to resume normal operation.
• Ensure that the return and/ or discharge air paths are not blocked by
curtains, blinds, furniture, etc.
• Adjust the Temperature control to a cooler or warmer setting as necessary.
• Clean the coils, (see Routine Maintenance), or remove obstruction.
• Be sure to use exhaust vent fans while cooking or bathing and, if possible,
try not to use heat producing appliances during the hottest part of the day.
• Allow additional time for the air conditioner to cool off a very hot room.
• Do not try to operate your air conditioner in the cooling mode when the
outside temperature is below 60 °F (16 °C). The unit will not cool properly,
and the unit may be damaged.
• Since the fan does not circulate the room air continuously at this setting,
the room air does not mix as well and hot (or cold) spots may result. Using
the continuous fan setting is recommended to obtain optimum comfort
levels.
• Check the cooling capacity of your unit to ensure it is properly sized for the
room in which it is installed. Room air conditioners are not designed to cool
multiple rooms.
• Check the heating capacity of your unit. Air conditioners are sized to meet
the cooling load, and heater size is then selected to meet the heating load. In
extreme northern climates, room air conditioners may not be able to be used as
a primary source of heat.
21
M. TROUBLESHOOTING
COMPLAINT CAUSE SOLUTION
• If there are heat producing appliances in use in the room, or if the room is
heavily occupied, the unit will need to run longer to remove the additional
heat.
• Be sure to use exhaust vent fans while cooking or bathing and, if possible,
try not to use heat producing appliances during the hottest part of the day.
• The use of higher efciency components in your new air conditioner may
result in the unit running longer than you feel it should. This may be more
apparent, if it replaced an older, less efcient, model. The actual energy
usage, however, will be signicantly less when compared to older models.
• The energy efciency ratio (EER) and cooling capacity rating (Btu/ h) listed
on the unit’s rating plate are both agency certied.
Unit Runs Too Much.
• This may be due to an excessive heat load in
the room.
• It may also be due to an improperly sized unit.
• This may be normal for higher efciency
(EER) air conditioners.
• You may notice that the discharge air
temperature of your new air conditioner
may not seem as cold as you may be
accustomed to from older units. This does
not; however, indicate a reduction in the
cooling capacity of the unit.
22
R . INFORMATION FOR THE OWNER
R.1 Routine Maintenance
WARNING: Service of this product (aside from filter
maintenance) shall only be performed by trained service
personnel. Refer to the Service Manual for procedures on
how to inspect and maintain the interior of the unit and its
components. A QR code is located in section A.4 which will
help you locate the service manual online.
23
Loading...