Friedrich BRO412W1A User Manual

Breeze

Service Questions: Contact Friedrich at [phone]
Sales Inquiries: Contact Sylvane at [phone] or visit sylvane.com

™

A revolution in room cooling

Installation Instructions

for BRO412W1A

4000 - 12000 Btu

Friedrich Part No. 96091000 (Rev. 01)

What’s in the carton?

Accessories

1. Breeze indoor module with 25 ft. connecting
line attached

2. Wall mounting template and bracket for in­door module

3. Breeze outdoor module

4. Outdoor module connection covers

5. Mounting pad for outdoor module

6. Remote control

7. Accessories (see list at right)

Tools you will need:

• Phillips screwdriver

• 1/2” wrench or crescent wrench

• Drill with Phillips bit and 3/16” drill bit

• Stud nder (recommended)

• 3” hole saw (through wall installations)

• Safety glasses (recommended)

• Trim knife

• Level

ITEM DESCRIPTION QTY

1. CONTROL BOX COVER DOOR 1

2. CONTROL BOX COVER 1

3. WIRE TIE 2

4. CONNECTING LINE BENDING GUIDE 1

5. ELECTRICAL CORD RETENTION BRACKET 1

6. WALL OPENING FILL GASKET 1

7. OUTDOOR UNIT WASHER FOR ANCHOR SCREW 4

8. OUTDOOR UNIT ANCHOR SCREW 4

9. SCREW #8 X 3/4” TRUSS HEAD 6

10. SCREW #8 X 1 1/2” PHILLIPS PAN HEAD 15

11. WALL ANCHOR FOR #8 X 1 1/2” SCREW 15

12. SECURITY SCREW 1

13. CONNECTING LINE CLIPS 5

1.

2.

3.

8.

6.

4.

5.

13.

12.

10.

9.

7.

11.

Before getting started

Identify the locations where you will mount the indoor
module and place the outdoor module. Keep in mind,
there is 25’ of connection line for connecting indoor and
outdoor pieces, so locate them accordingly. You cannot

add additional length if they are too far apart.

Placing the indoor unit

It is recommended that you install the indoor module on
an exterior wall within 6 feet of a properly rated outlet
for the system you are installing. The BR0412W1A plugs
into a 115V 15A outlet. The system should be plugged
into a single circuit outlet only. Typically, hanging the
indoor module above or adjacent to a window will
provide a great location. NOTE: You should not drill
through the window header (part of the rough framing)
located directly above the window opening.

Placing the outdoor unit

The outdoor module should be placed on a level surface
with adequate clearance from items like shrubbery,
solid fencing or other air conditioning equipment that

can impede airow to the module.

The outdoor module must be at least 12” from the wall

for proper airow. The mounting pad provided with the

system will raise the module off of the ground 3”. The
fan should face away from the building.

NOTE:
Be sure to place your
equipment with these
limitations in mind.

25 ft.
connecting

line

6" minimum

clearance

6" min.

6 ft. power
cord

25 ft. max.

12" minimum
clearance

DO NOT PLUG IN INDOOR UNIT until you have
completed the entire installation process.

6" min.

6 ft.
power
cord

CAUTION

SHOCK HAZARD - DO NOT PLUG-IN indoor unit until all installation work is completed!
Connect to a single dedicated circuit sized for the load.
DO NOT kink or bend refrigeration line-set less than 3” radius – A connecting line bending guide is provided.
Line-set is under high pressure – DO NOT Puncture line-set.
DO NOT Heat line-set.
Always follow all local and national codes when installing equipment. Obtain the help of trained, skilled
worker where necessary.

STEP 1 - Determine how you will connect the indoor and outdoor modules.
There are two options available:

OPTION 1 is to drill a 3” hole through the wall to pass
the connecting line through.

OPTION 2 is to use the Friedrich SimpleSill™ kit to pass
the connecting pipe through the window. The Simple­Sill™ is an optional accessory available where Breeze
is sold.

DO NOT PLUG IN INDOOR UNIT until you have
completed the entire installation process.