Freescale MPC7410RX400NE, MPC7410HX400NE, MPC7410VS400NE, MC7410VU400NE, MPC7410RX450NE DATA SHEET

查询MC7410VU400NE供应商

Freescale Semiconductor

Advance Information

Document Number: MPC7410ECS02AD

Rev. 2.0, 11/2007

--- Preliminary ---

MPC7410 RISC Microprocessor
Hardware Specifications Addendum
for the MPC7410

This document describes part number-specific changes to
recommended operating conditions and revised electrical
specifications, as applicable, from those described in the
general MPC7410 Har dwar e Specifications (Document No.
MPC7410EC).

Specifications provided in this document supersede those in
the MPC7410 Har dware Specifications, for the part numbers
listed in Table A only. Specifications not addressed herein
are unchanged. Because this document is frequently
updated, refer to http://www.freescale.com or to your
Freescale sales office for the lates t version.

xxnnn

NE Series

Freescale Part Numbers Affected:

MPC7410RX400NE
MPC7410HX400NE
MPC7410VS400NE
MC7410VU400NE
MPC7410RX450NE
MPC7410HX450NE
MPC7410VS450NE
MC7410VU450NE

Note that headings and table numbers in this document are
not consecutively numbered. They are intended to
correspond to the heading or table affected in the general
hardware specification. Part numbers addressed in this
document are listed in Table A. For more detailed ordering
information see Table 17.

This document contains information on a new product. Specifications and information herein
are subject to change without notice.

© Freescale Semiconductor, Inc., 2002, 2007. All rights reserved.

Features

Freescale Part

Number

Table A. Part Numbers Addressed by this Data Sheet

Frequency

Operating Conditions

Vdd T

(°C) OVdd

J

Significant Differences from Hardware

SpecificationCPU

MPC7410RX400NE
MPC7410HX400NE
MPC7410VS400NE

MC7410VU400NE

MPC7410RX450NE
MPC7410HX450NE
MPC7410VS450NE

MC7410VU450NE

400 MHz 1.5V±50mV 0 to

105

450 MHz 1.8V

±100mV

450 MHz 1.5V±50mV 0 to

500 MHz 1.8V

±100mV

0 to
105

105

0 to
105

1.8/2.5 V Reduced core voltage to achieve lower power
consumption. Removes 3.3V OVdd support. For
all AC/DC specifications not mentioned in this
document, please refer to the
MPC7410(RX/HX/VS)400LE and
MC7410VU400LE specifications in the general

MPC7410 Hardware Specifications

1.8/2.5/3.3 V The MPC7410(RX/HX/VS)400NE and
MC7410VU400NE also fully conform to the
MPC7410(RX/HX/VS)450LE and
MC7410VU450LE specifications, respectively.
Refer to the general

Specifications

1.8/2.5 V Reduced core voltage to achieve lower power
consumption. Removes 3.3V OVdd support. For
all AC/DC specifications not mentioned in this
document, please refer to the
MPC7410(RX/HX/VS)450LE and
MC7410VU450LE specifications in the general

MPC7410 Hardware Specifications

1.8/2.5/3.3 V The MPC7410(RX/HX/VS)450NE and
MC7410VU400NE also fully conform to the
MPC7410(RX/HX/VS)500LE and
MC7410VU500LE specifications, respectively.
Refer to the general

Specifications

MPC7410 Hardware

.

MPC7410 Hardware

.

.

.

2 Features

This section summarizes changes to the features of the MPC7410 described in the MPC7410 Hardware
Specifications.

• Bus interface
— Selectable interface voltages of 1.8 V, 2.5 V (3.3 V not supported)

4.1 DC Electrical Characteristics

Voltage to the L2 I/Os and processor interface I/Os are provided through separate sets of supply pins and
may be provided at the voltages shown in Table 2.

MPC7410 RISC Microprocessor Hardware Specifications Addendum for the MPC7410xxnnnNE Series, Rev. 2.0

2 Freescale Semiconductor

Table 2. Input Threshold Voltage Setting

Features

BVSEL Signal

3

Processor Bus Input

Threshold is Relative to:

L2VSEL Signal

L2 Bus Input Threshold is

3

Relative to:

Note

0 1.8 V 0 1.8 V 1

HRESET

2.5 V HRESET 2.5 V 1, 2

1 Not Supported 1 2.5 V 1, 4, 5

HRESET Not Supported HRESET Not Supported —

Notes:

1. Caution: The input threshold selection must agree with the OVdd/L2OVdd voltages supplied.

2. To select the 2.5-V threshold option, BVSEL and/or L2VSEL should be tied to HRESET

so that the two signals

change state together. This is the preferred method for selecting this mode of operation.

3. To overcome the internal pull-up resistance, a pull-down resistance less than 250 ohms should be used.

4. Default voltage setting if left unconnected (internal pulled-up).

5. Caution: The XPC7410RXnnnNE does not support the default OVdd setting of 3.3 V. The BVSEL input must be tie
either low or to HRESET

.

T able 3 provides the recommended operating conditions for the MPC7410 part numbers described herein.

Table 3. Recommended Operating Conditions

Characteristic Symbol Recommended Value Unit

Core supply voltage Vdd 1.5V ± 50mV V

PLL supply voltage AVdd 1.5V ± 50mV V

L2 DLL supply voltage L2AVdd 1.5V ± 50mV V

Processor bus supply voltage BVSEL = 0 OVdd 1.8V ± 100mV V

BVSEL = HRESET

BVSEL = HRESET

OVdd 2.5V ± 100mV V

OVdd Not Supported V

or BVSEL = 1

L2 bus supply voltage L2VSEL = 0 L2OVdd 1.8V ± 100mV V

L2VSEL = HRESET

L2OVdd 2.5V ± 100mV V

or L2VSEL = 1

Input voltage Processor bus and

V

in

GND to OVdd V

JTAG Signals

L2 Bus V

Die-junction temperature T

in

j

GND to L2OVdd V

0 to 105 °C

Note: These are the recommended and tested operating conditions. Proper device operation outside of

these conditions is not guaranteed.

MPC7410 RISC Microprocessor Hardware Specifications Addendum for the MPC7410xxnnnNE Series, Rev. 2.0

Freescale Semiconductor 3