Franke Foodservice WD1001 Installation Manual

FOOD WASTE DISPOSER OWNER'S GUIDE

BEABBEAB

ApprovedApp r o ve d

IMPORTANT - Read all instructions thoroughly.

Keep this guide for future reference.

CAUTION - Be sure to review SAFETY INSTRUCTIONS PERTAINING TO A RISK OF

FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS before installing disposer.

Our food waste disposer is a reliable appliance that will

offer your household many years of trouble free use. This

disposer has been uniquely designed to free your kitchen of

all organic food waste left over after the preparation and

clean-up of meals. Simply turn on the water, switch the

disposer on, put your food waste in the disposer and it will

shred the garbage into very fine particles that are easily

flushed through the sewer system without any problem. For

Batch Feed Operations, please see Section 6 of this manual.

Table of contents

1 MOUNTING ASSEMBLY

2 ELECTRICAL CONNECTIONS

Before installing and operating this disposer:

1. Make sure that the installation of this appliance is

allowed by the authorities.

2. Please read and follow all recommendations in this

manual to ensure trouble free operations.

If you have any questions, please contact your

retailer.

3 OVERFLOW/APPLIANCE CONNECTIONS

4 ATTACHING THE DISCHARGE ELBOW

5 CONNECTING DISPOSER TO MOUNT ASSEMBLY

6 OPERATING INSTRUCTIONS

7 TROUBLESHOOTING

8 CLEANING AND MAINTENANCE

9 ELECTRICAL INFORMATION

www.franke.co.uk

Important Safety Instructions

Instructions pertaining to risk of fire, electric shock or injury to persons.

Save these instructions.

WARNING - When using electrical appliances, basic precautions should always be followed, including the following:

1. Read all instructions before using

the appliance.

2. To reduce the risk of injury, close supervision is

necessary when an appliance is used near children.

3. Do not put fingers or hands into a waste disposer

while it is functioning.

4. Turn the power switch to the off position before

attempting to clear a jam or remove an object from

the disposer.

5. When attempting to loosen a jam in a waste

disposer, use a long wooden utensil e.g. spoon.

6. When attempting to remove objects from a

disposer, use long-handled tongs or pliers.

7. To reduce the risk of injury please note:

8. Additionally for continuous feed models:

• Care must be taken to ensure that the

supply is disconnected by switching off

the electric supply or by removing the

plug from the socket-outlet before

freeing a jammed rotor (as describe in

step 5).

• When not operating the disposer, leave

the stopper in place to reduce the risk of

objects falling into the disposer.

• Do not operate disposer unless splash guard is

in place.

9. For proper electrical earth instructions see the

ELECTRICAL CONNECTION details of this manual.

10. All installations should be carried out by a qualified

• this disposer is not for grinding hard

materials, such as glass and metal;

• this disposer must be connected to the

electric supply by means of either a

power supply cord or insulated wires in

a flexible conduit;

• when installing the disposer, care must

be taken to ensure that the reset button

of the overload protection device remains

readily accessible.

electrician.

11. The symbol on the product or on its packaging

indicates that this product may not be treated as

household waste. Instead, it shall be handed over

to the applicable environmental collection point for

the recycling of electrical and electronic equipment.

For more detailed information about recycling of this

product, please contact your local authority, your

household waste disposal service or the shop where

you purchased the product.

1. Components and Installation of mount assembly

PLEASE READ BEFORE INSTALLATION

NB: Pay close attention to the order of mount assembly parts, as they have been correctly assembled by the factory.

(See 1A and 1B.)

A. Disassemble the mounting assembly, as it has been shipped, by turning the sink flange until the projections align

with the notches in the mount ring and allow you to pull the sink flange up and out of the remaining mount

assembly. Note the sequence of these parts as they are stacked and refer to 1A and 1B to identify each part.

Unpack the 3 mount screws and screw them half way through the mount ring (notice “THIS SIDE UP” is imprinted

on top of the mount ring).

Next, stack the rubber gasket on top of the protector ring and sit them on top of the pointed ends of the

mount screws.

B. Keep these assembled parts together and set aside. Before you connect the disposer to the mount assembly

under the sink, you may want to practice engaging the groove of the Hush Cushion® to the ridge at the bottom

of the sink flange (see 1A and read Sec. 6).

C. Be sure your sink is clean. Pack the underside rim of the flange with putty (see 1C). Position the sink flange so it

is centred and readable as you look into your sink. Push the sink flange firmly into the sink opening to make a

good seal. DO NOT move or rotate the sink flange once seated or the seal may be broken.

D. Take the remaining portion of the mount assembly, as it was set aside and make sure that the rubber gasket is on

top of the protector ring. From under the sink, while holding the sink flange firmly with one hand, line up the

notches in the mount ring with the projections of the sink flange. Slide the mount assembly up onto the sink flange,

past the projections and give the mount assembly a 1/4 turn, so that it will hang by itself (see 1D).

E. Tighten the 3 mounting screws evenly with a screwdriver (see 1E). DO NOT OVERTIGHTEN! Trim off excess putty.

3-Bolt Mount System

SINK FLANGE

SINK FLANGE GASKET

PROTECTOR RING

MOUNTING SCREWS (3)

SINK MOUNT RING

1E

PUTTY

MOUNTING
SCREWS**

SCREW
CLAMP**

RIDGE

HOPPER

END BELL
(ELECTRICAL
CONNECTIONS)

SINK

RUBBER SINK
FLANGE GASKET**

PROTECTOR RING**

MOUNT RING**

HUSH CUSHION®**

DISHWASHER
DISCHARGE INLET

ELBOW
GASKET

1A

STOPPER*

SINK
FLANGE**

PROJECTIONS

RIDGE

SCREWS

ELBOW
FLANGE

DISCHARG
E ELBOW

Mount Assembly

PROTECTOR
RING

SCREW
CLAMP

HUSH
CUSHION

1C

SINK
FLANGE

MOUNTING
SCREWS

MOUNTING
RING

1D

1B

RUBBER
GASKET

SERIAL #- RECORD

* Batch Feed Stopper looks different than the stopper

illustrated.

** Mount Assembly (see 1B)

ON WARRANTY CARD