Franke Consumer Products FFP S700 User Manual

FFP S700 SERIES

Pull-Out Spray Faucet

Installation guide

G 1748.XX

ENGLISH

G 1782

G 29016

G R0637

TECHNICAL DATA

· Minimum working pressure 0,5 bar

· Maximum working pressure 5 bar

· Recommended working pressure 3 bar (in case of water pressure
higher than 5 bar it is recommended to install pressure reducers)

· Maximum working temperature 70°C

G 1156

G R0239.XX

G 13396.XX

G R1664

G 1636

G 1463

PARTS LIST

G 13396.XX Handle

G R0239.XX Ring cap

G 1156 Cartridge

G R0637 Fastening set (rubber washer, triangular ange, metal washer, nut)
G R1664 Valve-holder

G 1636 Counter weight and gaskets
G 1463 Flexible hose

G 1748.XX Spray head

G 1782 Supply exible hose

G 29016 Supply exible hose

TECHNICAL FEATURES

Maximum water ow 2.2 gpm - 60 psi
Recommended pressure range 15-75 psi - Over 75 psi PRV required
Complies with Proposition 65, NSF61, UPC and C-UPC requirements

2

Faucet installation

ENGLISH

Please remove all components from package and inspect prior to
installation (see itemized table and picture).

NOTE:

Call us immediately if you see inconsistencies. (1-800-626-5771)

or visit

www.frankeksd.com

TABLE OF CONTENTS

1 Faucet

2 Fastening set (rubber washer, triangular ange, metal washer, nut)

3 Counter weight and gaskets

4 Spray head

5 Valve-holder

1

2

3

4

Remove all mounting hardware from protecting plastic bag.

3

5

Install faucet to the sink or countertop

ENGLISH

Set the faucet into place on the sink as indicated in the gure.

NOTE:
the rubber O-ring should be sitting on top of the countertop and between
the faucet body. DO NOT use putty or other sealant at this location.

4

Install faucet to the sink or

ENGLISH

countertop - follows

1

2

3

4

21 mm [13/16”] key

Install the fastening components to the faucet’s threaded shank in the
following sequence: O-ring (1), triangular ange (2), metal washer
(3) and threaded nut (4) (the triangular ange can be omitted if the
sink/countertop is too thick).

5

Attach the valve-holder

ENGLISH

20 mm [13/16”] key

Attach the valve-holder to the shorter tubing and attach the spray

hose to the valve-holder.

NOTE:
The provided small black rubber washer needs to be installed here.
DO NOT use putty or other sealant agents at this joint.

6

Connect the supply line

ENGLISH

16 mm [5/8”] key

Connect the supply line. In order to guarantee a long use of the pro­duct, install the angle valve equipped with lter and clean them regu­larly. Do not allow the supply tube to twist or bend sharply.
Flush out debris from water lines and faucet.

1. Pull spray hose out of the faucet spout and point the

open end towards the sink drain.

2. Open faucet handle - cold side rst - by turning handle
to the right and moving it upward

3. Let the faucet run on cold for 15 to 30 seconds.

4. Open faucet handle - hot side second - by turning han­dle to the left and moving it upward.

5. Let the faucet run on cold for 15 to 30 seconds.

6. Turn faucet off.

7. Test for leaks under the cabinet.

7

Assemble Pull-out Spray

ENGLISH

Attach the pull-out spray head to the hose.
NOTE:

The rubber washer needs to be installed to prevent leakage.

Fasten the weight to the hose as shown in picture below. Test all water

lines, tting and connections for leaks.

8

Replacing the cartridge

ENGLISH

B

2,5 mm [1/8”] Allen key

A

28 mm [1-1/8”] key

E

F

D

C

Before starting, shut off the water supply to the faucet and move the
faucet handle to the off position. Use a 2.5mm [1/8”] Allen key to
loosen the set screw (A) which is accessible from the back of the han­dle. Lift the handle (B) from the cartridge (F). Find the small notch at
the base of the chrome ring cap and carefully pry up against this to re­move the cap (C). Remove the brass retaining ring (E) using a 21 mm
[1-1/8”] wrench. Lift out the cartridge (F). Ensure that the grommets
(O-rings) are in good condition and properly seated and remove all
mineral deposits. Install the new cartridge so that the central pivots t

into the corresponding seats.

9

General maintenance

ENGLISH

Do not use harsh detergents, solvents, chemical agents, metallic
sponges, etc. that could harm the surface.
Clean only with a soft sponge and soapy water.
Clean and then dry properly the faucet in case of very hard or calcare­ous water, whose deposits cold damage the surface.

10

Limited lifetime warranty

ENGLISH

Franke Consumer Products, Inc., Kitchen Systems Division extends the following warranty to the origi­nal purchaser of its faucets effective January 1, 2003.

All faucets installed in a private residence will carry a limited lifetime warranty on all mechanical
parts to be free of manufacturing defects in material and workmanship under normal usage. All chrome

nishes carry a limited lifetime warranty; all other nishes are warranted for ve (5) years form the
original date of purchase.

Marine and Outdoor Installation: Franke Consumer Products, Inc. faucets are NOT warranted for
Marine and Outdoor installations.

This warranty applies only to the original owner, providing the product has been installed in accordance

with our installation instructions, used as recommended and in a normal residential application. In the
event of a warranty claim, the owner will be required to provide proof of purchase - save sales
receipt. This warranty covers all components which make the product operational. Franke, at its op-

tion, may repair or replace the product or components necessary to restore the product to good working
condition. Franke reserves the right to inspect the installation prior to the actual replacement of the
product or component part.

This warranty does not cover misuse or abuse, accidental damages, scuffs or scratches, improper instal­lation, abnormal usage, negligence or damage caused by improper maintenance or cleaning. Normal
wear of parts is excluded from the warranty. Damage caused by impurities or acts beyond our control
are not covered. Any product or part which has been repaired or altered in any manner outside of Fran­ke’s factory, unless previously authorized in writing by Franke, will void warranty. Any replacement
excludes transportation and any labor re-installation costs. This warranty does not allow recovery of
incidental or consequential damages such as loss of use, delay, property damage or other consequential
damage, and Franke accepts no liability for such damages.

The Franke warranty is limited to the above conditions and to the warranty period specied herein and is
exclusive. Franke DISCLAIMS all other warranties, expressed or implied, including IMPLIED WAR­RANTIES OF MERCHANTABILITY AND/OR FITNESS FOR AS PARTICULAR PURPOSE. This
warranty gives you specic legal rights that may vary from state to state.

Further information

For any further information about our products, about the installation
of them or about the guarantee, please dial the number of the
customer service:

Phone number [phone]
Or: 1-800-626-5771
Fax number + 1-215-822-5873

Franke Consumer Products Inc. - Kitchen Systems Division

3050 Campus Drive, Suite 500 Hateld, PA 19440

11