Foxconn T77H054 User Manual

HSINCHU SCIENCE PARK BRANCH OFFICE

HON HAI PRECISION IND. CO., LTD.

WLAN USB MODULE

T77H054

USER’S MANUAL

HSINCHU SCIENCE PARK BRANCH OFFICE

HON HAI PRECISION IND. CO., LTD.

Contents

SECTION ONE: INTRODUCTION................................................................................................................3

1.1 WLAN FEATURES .................................................................................................................................................................3

1.2 FCC NOTICE..........................................................................................................................................................................4

1.3 CANADA NOTICE....................................................................................................................................................................5

SECTION TWO: WIRELESS UTILITY AND CONFIGURATION..................................6

2-1 WINDOWS 98/ME/2000 WIRELESS UTILITY ......................................................................................................................6

SECTION THREE: WINDOWS XP WIRELESS UTILITY AND

CONFIGURATION ........................................................................................................................................................11

3-1 WINDOWS XP WIRELESS UTILITY .....................................................................................................................................11

APPENDIX A GLOSSARY......................................................................................................................................................16

The information contained in this manual has been verified at the time of this manual printing. The manufacturer reserves the right to make any changes and improvements in the product described in this manual at any time and without notice. All registered trademarks are the property of their respective owners.

HSINCHU SCIENCE PARK BRANCH OFFICE

HON HAI PRECISION IND. CO., LTD.

Section One: Introduction

This WLAN USB Module is in compliance with IEEE 802.11b and IEEE 802.11g Standards. The data rate of

802.11g is capable of up to 54 Mbps with fallback rates of 48, 36, 24, 18, 12, 9 and 6 Mbps. The data rate of

802.11b is capable of up to 11 Mbps with fallback rates of 5.5, 2 and 1 Mbps.

1.1 WLAN Features

Form Factor & Bus Interface Form Factor: Non-standard, Interface: USB 2.0.

Wireless LAN Compliance Compatible with IEEE 802.11b and IEEE802.11g standard

and USB2.0 Specification.

Operating Frequency 2412 ~ 2483.5 MHz ISM band

Modulation Schemes 802.11g: OFDM, DQPSK, DBPSK and CCK

802.11b: DQPSK, DBPSK and CCK

Channel Numbers IEEE 802.11b compliant

1 ~ 11 channels for United States

1 ~ 13 channels for Europe

1 ~ 13 or 14 channels for Japan

WLAN Data Rate 802.11g: Up to 54 Mbps with auto fallback to 48, 36, 24, 18, 12,

9 and 6 Mbps.

802.11b: Up to 11 Mbps with auto fallback to 5.5, 2 and 1Mbps.

Media Access Protocol CSMA/CA with ACK

Transmitter Output Power 802.11b: 17.5+/-1.5 dBm

802.11g: 15.0+/-1.5 dBm

Antenna Type Integrated diversity switch with Printed Antenna.

Operating Voltage 3.3 VDC

Operating Systems Windows 98/Me/2000/XP

HSINCHU SCIENCE PARK BRANCH OFFICE

HON HAI PRECISION IND. CO., LTD.

1.2 FCC Notice

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

IMPORTANT NOTE: FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FOXCONN declared that T77H054.00 is limited in CH1~11 from 2412 to 2462 MHz by specified firmware controlled in USA.

This device is intended only for OEM integrators under the following conditions:

The antenna must be installed such that 20 cm is maintained between the antenna and users, and

The transmitter module may not be co-located with any other transmitter or antenna.

As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).

IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop

configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

End Product Labelling

This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labelled in a visible area with the following: “Contains FCC ID: MCLT77H054”.

Manual Information That Must be Included

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrate this module.

The users manual for OEM integrators must include the following information in a prominent location “ IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

HSINCHU SCIENCE PARK BRANCH OFFICE

HON HAI PRECISION IND. CO., LTD.

1.3 Canada Notice

Industry Canada Statement

Operation is subject to the following two conditions:

1) this device may not cause interference and

2) this device must accept any interference, including interference that may cause undesired operation of the device

IMPORTANT NOTE: IC Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

+ 11 hidden pages