Foxconn J20H064 User Manual

HON HAI PRECISION IND. CO., LTD.
No.2, 2nd Dong Huan Road, 10th
YouSong lndustrial District, Longhua
Town, Baoan, ShenZhen

User Manual

WiFi+ BT Module

Project Name WiFi+ BT Module

Approval Sheet Rev.
Foxconn Part No. J20H064

1.0

Prepared by Reviewed by Approved by

Shu-yu Li Xue-dong Jiang

1

CONTENTS

1 PRODUCT INTRODUCTION .............................................................. 3

1.1 APPLICATION SCOPE ..................................................................... 3

2 MODULE HARDWARE OVERVIEW ........................................................ 4

2.1 BLOCK DIAGRAM ........................................................................ 4

2.2 FEATURES ............................................................................. 4

2.3 INTERFACE AND CONNECTOR .............................................................. 4

3 ELECTRICAL SPECIFICATION ............................................................ 6

3.1 ABSOLUTE MAXIMUM RATING ............................................................... 6

3.2 RECOMMENDED OPERATING RATING ......................................................... 6

3.3 DC CHARACTERISTICS ................................................................... 6

3.4 ESD INFORMATION ...................................................................... 6

3.5 ENVIRONMENT STORAGE CONDITION ........................................................ 6

4 RF SPECIFICATION ..................................................................... 7

4.1 IEEE802.11B .......................................................................... 7

4.2 IEEE802.11G .......................................................................... 8

4.3 802.11N HT20 ......................................................................... 9

4.4 BLUETOOTH STANDARD SPECIFICATIONS ..................................................... 9

5 MECHANICAL SPECIFICATIONS......................................................... 13

5.1 SHIELDING COVER DIMENSION ............................................................ 13

5.2 PCB ASSEMBLY DIMENSION .............................................................. 14

2

1 Product Introduction

The J20H064 802.11b/g/n+Bluetooth4.0 module provides wireless modem
functionality utilizing direct sequence spread spectrum and OFDM/CCK technology. This
module is based on Marvell 88W8766P solution which is integrated 2.4GHz IEEE802.11
b/g/n (MAC/baseband/radio), Bluetooth 4.0 + High speed and power amplifiers (PA).

1.1 Application scope

The wireless LAN is compliant to IEEE 802.11b and IEEE 802.11g and IEEE 802.11n
standard. The data rate of 802.11b is up to 11Mbps and fallback rates of 5.5, 2, 1Mbps.
The data rate of 802.11g is up to 54Mbps and fallback rates of 48,36,24,18,12,9, 6Mbps.
The data rate of 802.11n HT20 is up to 65Mbps and fallback rates of 58.5, 52, 39, 26, 19.5,
13, 6.5Mbps;

3

2 Module Hardware Overview

2.1 Block Diagram

The general HW architecture is shown below Figure:
.

Module Block Diagram

2.2 Features

♦ IEEE802.11b/g/n (1X1) and Bluetooth 4.0 based on Marvell 88W8766P solution.
♦ USB 2.0 Interface, High and Full Speeds supported.
♦ Module is powered by the host with a 5.0V +/- 5% supply.
♦ External PCB printed antennas.
♦ Two SPDT switch for antenna diversity and Bluetooth function.
♦ 2 layers single side design, through hole PCB design with halogen free FR4

material

2.3 Interface and Connector

♦ Pin definition:
♦ Vendor: JST
♦ Vendor P/N: SM05B-GHS-TB(LF)(SN)

4

Pin Number

1
2
3
4

5
S1
S2

Symbol Name Status Pin definition

GND Ground

DP I/O USB positive data

DM I/O USB negative data

UV+ P USB +5V power input
GND Ground
GND Ground
GND Ground

5

3 Electrical Specification

3.1 Absolute maximum rating

Element

DC supply voltage

3.2 Recommended operating rating

Element

DC supply voltage

3.3 DC Characteristics

Symbol

UV+

Tx Current(MCS0/15Bm/HT20) 200 280

Tx Current(MCS7/15dBm/HT20) 200 280

Parameter Min Typ

Supply voltage 4.5 5.0

Tx Current(1M/15dBm) 200 280

Tx Current(11M/15dBm) 200 280

Tx Current(6M/15dBm) 200 280

Tx Current(54M/15dBm) 200 280

Rx Current 90
Bluetooth TX 1 10
Bluetooth RX -- 110

Symbol Min Typ

UV+ 5.0

Symbol Min Typ

UV+ 4.5 5.0

Max Unit

6.5 (V)

Max Unit

5.5 (V)

Max Unit

5.5 (V)
400 (mA)
400 (mA)
400 (mA)
400 (mA)
400 (mA)
400 (mA)

(mA)
(mA)
(mA)

3.4 ESD Information

Mode Level Unit

HBM +/-1500 V

MM +/-200 V

3.5 Environment Storage Condition

Environment condition

Temperature

Humidity

Operating Temperature: -10 deg.C ~70 deg.C

Storage Temperature: -40 deg.C ~80 deg.C

Operating Humidity: 20% ~90%

Storage Humidity: 20% ~90%

6

4 RF Specification

4.1 IEEE802.11b

Items Contents

Specification IEEE802.11b
Mode DSSS / CCK
Channel CH1 to CH13
Data rate 1, 2, 5.5, 11Mbps
TX Characteristics Min. Typ. Max. Unit

1. Power Levels (Calibrated)

1) Target Power@1Mbps 13.5 15 16.5

2) Target Power@2Mbps

3) Target Power@5.5Mbps

4) Target Power@11Mbp s

2. Spectrum Mask @16dBm

1) fc-33MHz ＜ f ＜ fc-22MHz - - -50 dBr

2) fc-22MHz ＜ f ＜ fc-11MHz - - -30 dBr

3) fc+11MHz ＜ f ＜ fc+22MHz - - -30 dBr

4) fc+22MHz ＜ f ＜ fc+33MHz - - -50 dBr

3. Frequency Error -15 - +5 ppm
4 Modulation Accuracy(EVM)@16dBm

1) 1Mbps - -10 dB

2) 2Mbps - -10 dB

3) 5.5Mbps - -10 dB

4) 11Mbps - -10 dB
RX Characteristics Min. Typ. Max. Unit
5 Minimum Input Level Sensitivity

1) 1Mbps (FER≦8%) - -95 -92 dBm

2) 2Mbps (FER≦8%) - -92 -89 dBm

3) 5.5Mbps (FER≦8%) - -90 -87 dBm

4) 11Mbps (FER≦8%) - -88 -85 dBm
6 Maximum Input Level (FER≦8%) -10 -5 - dBm

13.5 15 16.5

13.5 15 16.5

13.5 15 16.5

dBm
dBm
dBm
dBm

7

4.2 IEEE802.11g

Items Contents

Specification IEEE802.11g
Mode OFDM
Channel CH1 to CH13
Data rate 6, 9, 12, 18, 24, 36, 48, 54Mbps
TX Characteristics Min. Typ. Max. Unit

1. Power Levels (Calibrated)

1) Target Power@6Mbps

2) Target Power@9Mbps

3) Target Power@12Mbps

4) Target Power@18Mbps

5) Target Power@24Mbps

6) Target Power@36Mbps

7) Target Power@48Mbps

8) Target Power@54Mbps

2. Spectrum Mask @14dBm

1) at fc +/- 11MHz - - -20 dBr

2) at fc +/- 20MHz - - -28 dBr

3) at fc > +/-30MHz - - -40 dBr
3 Modulation Accuracy(EVM)@14dBm

1) 6Mbps - - -5 dB

2) 9Mbps - - -8 dB

3) 12Mbps - - -10 dB

4) 18Mbps - - -13 dB

5) 24Mbps - - -16 dB

6) 36Mbps - - -19 dB

7) 48Mbps - - -22 dB

8) 54Mbps - -28 -25 dB
4 Frequency Error -15 - +5 ppm
RX Characteristics Min. Typ. Max. Unit
5 Minimum Input Level Sensitivity

1) 6Mbps (PER <10%) - -89 -86 dBm

2) 9Mbps (PER < 10%) - -87 -84 dBm

3) 12Mbps (PER < 10%) - -85 -82 dBm

4) 18Mbps (PER < 10%) - -83 -80 dBm

5) 24Mbps (PER < 10%) - -80 -77 dBm

6) 36Mbps (PER < 10%) - -77 -74 dBm

7) 48Mbps (PER < 10%) - -73 -70 dBm

8) 54Mbps (PER < 10%) - -72 -69 dBm
6 Maximum Input Level (PER < 10%) -20 -11 - dBm

13.5 15 16.5 dBm

13.5 15 16.5 dBm

13.5 15 16.5 dBm

13.5 15 16.5 dBm

13.5 15 16.5 dBm

13.5 15 16.5 dBm

13.5 15 16.5 dBm

13.5 15 16.5 dBm

8

4.3 802.11n HT20

Items Contents

Specification IEEE802.11n HT20
Mode OFDM
Channel CH1 to CH13
Data rate (MCS index) MCS0/1/2/3/4/5/6/7

TX Characteristics

1. Power Levels (Calibrated)

1) Target Power@MCS0

2) Target Power@ MCS1

3) Target Power@ MCS2

4) Target Power@ MCS3

5) Target Power@ MCS4

6) Target Power@ MCS5

7) Target Power@ MCS6

8) Target Power@ MCS7

2. Spectrum Mask @14dBm

1) at fc +/- 11MHz

2) at fc +/- 20MHz

3) at fc > +/-30MHz

3. Modulation Accuracy(EVM)@14dBm

1) MCS0

2) MCS1

3) MCS2

4) MCS3

5) MCS4

6) MCS5

7) MCS6

8) MCS7

4. Frequency Error

RX Characteristics

5. Minimum Input Level Sensitivity

1) MCS0 (PER < 10%) -

2) MCS1 (PER < 10%) -

3) MCS2 (PER < 10%) -

4) MCS3 (PER < 10%) -

5) MCS4 (PER < 10%) -

6) MCS5 (PER < 10%) -

7) MCS6 (PER < 10%) -

8) MCS7 (PER < 10%) -

6. Maximum Input Level (PER < 10%)

Min. Typ. Max. Unit

13.5 15 16.5 dBm

13.5 15 16.5 dBm

13.5 15 16.5 dBm

13.5 15 16.5 dBm

13.5 15 16.5 dBm

13.5 15 16.5 dBm

13.5 15 16.5 dBm

13.5 15 16.5 dBm

- - -20 dBr

- - -28 dBr

- - -45 dBr

- - -5 dB

- - -10 dB

- - -13 dB

- - -16 dB

- - -19 dB

- - -22 dB

- - -25 dB

- - -28 dB

-15 - +5 ppm

Min. Typ. Max. Unit

-88 -85

-85 -82

-83 -80

-80 -77

-77 -74

-73 -69

-71 -68

-70 -67

-20 -10

- dBm

dBm
dBm
dBm
dBm
dBm
dBm
dBm
dBm

4.4 Bluetooth Standard Specifications

Bluetooth Core Specification version 4.0:
Support all Bluetooth 4.0+HS packet types.
Operating frequency range: 2400MHz ~2483.5MHz
Modulation type:
Basic rate 1Mbps: GFSK,
Enhanced data rate 2Mbps: DQPSK
Enhanced data rate 3Mbps: 8DPSK

9

5 Operation SOP

1: Install normal driver under Linux PC
2: search WiFi AP and double click to make connection
3: If connection setup is ok, PC can communicate with network through wireless AP.

10

Items Contents

Specification

Frequency range
Data rate 1Mbps, 2Mbps, 3Mbps

- TX Characteristics -

1. Power Levels

BT Output Power -3 1 3 dBm

BT4.0+EDR

2.4GHz~2.4835GHz

Min. Typ. Max. Unit

2. Initial Carrier Frequency Tolerance

Average Offset

3. Carrier Drift
Drift Rate

DH1
DH3

DH5

Average Drift

DH1
DH3

DH5

4. Modulation Characteristic
F1avg
F2max
F1/F2 Ratio

5. EDR Relative Transmit Power
2Mbps: P[DQPSK]-P[GFSK]

3Mbps: P[8DPSK]-P[GFSK]

6. EDR Carrier Frequency Stability and Modulation Accuracy

-75 2 75 kHz

-20 -3 20 kHz/50us

-20 0 20 kHz/50us

-20 4 20 kHz/50us

-25 -3 25 kHz

-40 -4 40

-40 -5 40

140 164 175 kHz
115 135

0.8 0.90

-4 -0.15 1

-4 -0.2 1

kHz
kHz

kHz

dB
dB

2Mbps: π/4 DQPSK

Initial Frequency Error: ωi
Frequency Error: ω0

Block Frequency Error: ωi + ω0
RMS DEVM

Peak DEVM
99% DEVM (% Symbols <=0.3)

3Mbps: 8DPSK

Initial Frequency Error: ωi
Frequency Error: ω0

Block Frequency Error: ωi + ω0
RMS DEVM
Peak DEVM
99% DEVM (% Symbols <=0.13)

7. Tx Spurious Emission

30MHz- 1GHz - -60 -36 dBm
1GHz – 13.2GHz - -60 -30 dBm

-75 1.2 75

-10 0 10

-75 2 75

- - 0.2

- - 0.35

99% 100%

-75 1 75

-10 0 10

-75 1.6 75

- - 0.13

- - 0.25

99% 100%

kHz
kHz

kHz

kHz
kHz

kHz

11

Items Contents

Specification

Frequency range
Data rate 1Mbps, 2Mbps, 3Mbps

- RX Characteristics -

BT4.0+EDR

2.4GHz~2.4835GHz

Min. Typ. Max. Unit

1. Minimum Input Level Sensitivity

GFSK (1Mbps)
π/4 DQPSK (2Mbps)

8DPSK (3Mbps)

2. Maximum Input Level

GFSK (1Mbps)
π/4 DQPSK (2Mbps)
8DPSK (3Mbps)

3. Rx Emission

30MHz- 1GHz - - -57 dBm
1GHz – 13.2GHz - - -47 dBm

- - -79 dBm

---72 dBm

- - -72 dBm

-20 0 dBm

-20 0 dBm

-20 0 dBm

12

6 Mechanical Specifications

6.1 Shielding Cover Dimension

Dimension (LxWxH): 20.32mm x 18.28mm x 2.4mm
Thickness: 0.2mm

13

6.2 PCB Assembly Dimension

Dimension (W x Lx H ): 51.8mmx20mmx0.9mm
PCB: 2 layer HF-FR4 design

Industry Canada statement:

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux
appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions
suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce
dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de
provoquer un fonctionnement indésirable.

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour
un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un
minimum de 20 cm de distance entre la source de rayonnement et votre corps.

This device is intended only for OEM integrators under the following conditions:

14

(For module device use)

1) The antenna must be installed such that 20 cm is maintained between the antenna and
users, and

2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed.

Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions
suivantes: (Pour utilisation de dispositif module)

1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre
l'antenne et les utilisateurs, et

2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur
l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours
responsable des essais sur son produit final pour toutes exigences de conformité
supplémentaires requis pour ce module installé.

IMPORTANT NOTE:

In the event that these conditions can not be met (for example certain laptop configurations
or co-location with another transmitter), then the Canada authorization is no longer
considered valid and the IC ID can not be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate Canada authorization.

NOTE IMPORTANTE:

Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines
configurations d'ordinateur portable ou de certaines co-localisation avec un autre
émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut
pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé
de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation distincte
au Canada.

End Product Labeling

This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final
end product must be labeled in a visible area with the following: “Contains IC: 2878D­J20H064”.

Plaque signalétique du produit final

Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où
l'antenne peut être installée de telle sorte qu'une distance de 20cm peut être maintenue
entre l'antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible
avec l'inscription suivante: "Contient des IC: 2878D- J20H064".

Manual Information To the End User

The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module in the user’s manual of the end product which
integrates this module.
The end user manual shall include all required regulatory information/warning as show in
this manual.

Manuel d'information à l'utilisateur final

L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final
quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur
du produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises
et avertissements comme indiqué dans ce manuel.

15

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.

This device is intended only for OEM integrators under the following conditions:

1) The antenna must be installed such that 20 cm is maintained between the antenna
and users, and

2) The transmitter module may not be co-located with any other transmitter or
antenna.
As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example
certain laptop configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID can not be used on the
final product. In these circumstances, the OEM integrator will be responsible for
reevaluating
the end product (including the transmitter) and obtaining a separate FCC
authorization.

End Product Labeling

16

This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The
final end product must be labeled in a visible area with the following: “Contains FCC
ID: MCLJ20H064”. The grantee's FCC ID can be used only when all FCC compliance
requirements are met.

Manual Information To the End User

The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module.
The end user manual shall include all required regulatory information/warning as show

in this manual.

For Taiwan 警語： (電信管制射頻器材使用)

經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻

率、加大功率或變更原設計之特性及功能。

低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立

即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線

電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之

干擾。

Note: 1. 本模組於取得認證後將依規定於模組本體標示審驗合格標籤 2. 系統廠商應於平
台上標示「本產品內含射頻模組:

XXXyyyLPDzzzz-x (NCC ID) 」字樣

Europe – EU Declaration of Conformity

ThisdevicecomplieswiththeessentialrequirementsoftheR&TTEDirective1999/5/EC.Thefollowingtestmethodshavebeen
appliedinordertoprovepresumptionofconformitywiththeessentialrequirementsoftheR&TTEDirective1999/5/EC:



‐ EN60950‐1:2006+A11:2009+A1:2010+A12:2011

SafetyofInformationTechnologyEquipment



‐ EN62311:2008

Assessment
Hz‐300GHz)
(IEC62311:2007(Modified))



EN300328V1.7.1:2006

‐ ElectromagneticcompatibilityandRadiospectrumMatters(ERM);WidebandTransmissionsystems;Datatransmission

equipmentoperatinginthe2,4GHzISMbandandusingspreadspectrum
essentialrequirementsunderarticle3.2oftheR&TTEDirective



EN301489‐1V1.8.1:2008
ElectromagneticcompatibilityandRadioSpectrumMatters(ERM);ElectroMagneticCompatibility(EMC)standardforradio
equipmentandservices;Part1:Commontechnicalrequirements



EN301489‐17V2.1.12009

ofelectronicandelectricalequipmentrelatedtohumanexposurerestrictionsforelectromagneticfields(0

modulationtechniques;HarmonizedENcovering

17

ElectromagneticcompatibilityandRadiospectrumMatters(ERM);ElectroMagneticCompatibility(EMC)standardforradio
equipmentandservices;Part17:Specificconditionsfor2,4GHzwidebandtransmissionsystemsand5GHzhighperformance
RLANequipment



NationalAuthoritieswereinformedaccordingtoArticle6.4ofFrequencyNotification.

SpecialRequirementsareconsidered.Theproduct

islabeledwithCEMarking.

Česky

[Czech]

Dansk

[Danish]

[Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se
základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.

Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr
[udstyrets typebetegnelse] overholder de væsentlige krav og øvrige relevante
krav i direktiv 1999/5/EF.

Deutsch

[German]

Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in
Übereinstimmung mit den grundlegenden Anforderungen und den übrigen
einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.

Eesti

[Estonian]

Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme
tüüp = type of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja
nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

English Hereby, [name of manufacturer], declares that this [type of equipment] is in

compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.

Español

[Spanish]

Por medio de la presente [nombre del fabricante] declara que el [clase de
equipo] cumple con los requisitos esenciales y cualesquiera otras disposiciones
aplicables o exigibles de la Directiva 1999/5/CE.

Ελληνική

[Greek]

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ΔΗΛΩΝΕΙ ΟΤΙ [type of equipment]
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ
ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.

Français

[French]

Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est
conforme aux exigences essentielles et aux autres dispositions pertinentes de la
directive 1999/5/CE.

Italiano

[Italian]

Con la presente [nome del costruttore] dichiara che questo [tipo di
apparecchio] è conforme ai requisiti essenziali ed alle altre disposizioni
pertinenti stabilite dalla direttiva 1999/5/CE.

Latviski

[Latvian]

Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of
equipment / iekārtas tips] atbilst Direktīvas 1999/5/EK būtiskajām prasībām un
citiem ar to saistītajiem noteikumiem.

Lietuvių

[Lithuanian]

Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka
esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.

Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in

Nederlands
[Dutch]

Malti

[Maltese]

overeenstemming is met de essentiële eisen en de andere relevante
bepalingen van richtlijn 1999/5/EG.

Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott]
jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm
fid-Dirrettiva 1999/5/EC.

Magyar Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó

18

[Hungarian] alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Polski

[Polish]

Português
[Portuguese
]

Slovensko
[Slovenian]

Slovensky
[Slovak]

Suomi
[Finnish]

Svenska
[Swedish]

Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z
zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami
Dyrektywy 1999/5/EC.

[Nome do fabricante] declara que este [tipo de equipamento] está conforme
com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.

[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami
in ostalimi relevantnimi določili direktive 1999/5/ES.

[Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky
a všetky príslušné ustanovenia Smernice 1999/5/ES.

[Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen
tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja

sitä koskevien direktiivin muiden ehtojen mukainen.
Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse

med de väsentliga egenskapskrav och övriga relevanta bestämmelser som
framgår av direktiv 1999/5/EG.

19