Foster F40, F85, F20, F60 User Manual

F20, F40, F60, F85 installation and operating instructions
Cube Ice Maker
GB
Operating instructions
operating instructions
Foster European Operations
Oldmedow Road, King’s Lynn, Norfolk, PE30 4JU England
Tel: 01553 691122 Fax: 01553 691447 Website: www.fosterrefrigerator.co.uk Email: sales@foster-uk.com
a Division of ITW (UK) Ltd.
France
Foster Refrigerator France SA Tel: (33) 01 34 30 22 22 Fax: (33) 01 30 37 68 74 Email: info@fosterfrance.com
Germany
Foster Refrigerator Germany Tel: (0781) 96 93 00 Fax: (0781) 96 93 019 Email: info@fosterrefrigerator.de
FSERIESICECUBER/OP/INS 08/04 00-555226
F
Notice d’installation
D
Bedienungsanleitung
NL
Gebruiksaanwijzing
This publication is
intended to acquaint you with the correct use of this ice machine and with the care that is required for trouble free operation and optimum performance. It is important to adhere to the instructions indicated. We suggest that you thoroughly read this manual, paying close attention to the warnings
and advice that are given. Whenever communicating with the manufacturer about your machine, always indicate the model and serial number.
english
GB
2
Important:
Carefully read this user manual before installing the machine.
Warning
Disconnect the electrical power before beginning any maintenance or cleaning operation.
2
preface
General Information at Delivery
1
Please note the following guidelines:
That the packing
does not show any sign of damage.
That the unit
corresponds to what is specified on the purchase order.
That the machine is not damaged externally and
no parts are missing.
That during transport certain integral parts have
not been damaged.
In case of severe damage or parts missing, report immediately to the delivering carrier and your distributor. The illustrations shown in this manual are generic and can differ in some details from the delivered machine. Any illustration, schematic or documents supplied with the machine belong to the manufacturer who reserve copyright and expressly forbids any reproduction of them without written permission. The Manufacturer's policy is one of continuous improvement and reserves the right to make changes at any time without prior notice or incurring any obligation whatsoever.
unit description
3
The units described in this
manual are self-contained
cube ice makers, namely
with a built in ice
storage bin.
A percentage of ice
production capacity can be
stored in the self contained
bin in which a sensor
controls the collected
ice level.
When this control is in contact with the stored ice, the thermostat cuts-off the unit operation. Another thermostat controls all the process sequences of the machine related to ice making and release of ice cubes.
safety instructions
4
For the correct unit operation you must carefully read this manual and adhere to its instructions, by doing this your machine will operate safetly and last for several years to come. If in any doubt you should contact your local distributor.
The Manufacturer accepts no responsibility whatsoever for any damage or injury to people resulting from the non-observance of the safety instructions.
11
Attention
Maintenance and cleaning operations must be performed by authorised service agents.
13
Never push or drag it.
6
Make sure your hands are properly wiped dry.
The electrical isolator switch must be within hand reach of the installed machine.
The water shut-off valve must be within hand reach of the installed machine.
8
Important
Do not remove any service panel secured with screws.
5
If the unit is to be moved, be sure to lift it rather than damage the levelling feet.
12
Make sure that the cabinet is connected to a mains electrical supply complete with an earth connection.
14
7
9
10
transport
15
As transport protection the ice maker is packed in a heavy cardboard crate.
For moving the packed unit to site use a fork lift with forks no thicker than 40mm.
16
17
For the unpacking of the unit observe the pictorial view.
Make sure and locate the ice scoop inside the ice storage bin. Make sure water and drain pipes are inside the ice storage bin.
18
15
DISPOSAL REQUIREMENTS
If not disposed of properly all refrigerators have components that can be harmful to the environment. All old refrigerators must be disposed of by appropriately registered and licensed waste contractors, and in accordance with National laws and regulations.
3
english
GB
how the installation is made
location
Position the ice maker in its final location and make sure that there is everything for its installation, namely:
A minimum clearance of 15cm (6 in) must be left at the sides of the machine for routing cooling air drawn into and exhausted out of the compartment to maintain a proper condensing operation.
Fused switched power supply.
19
20
Water supply connection with shut-off valve.
Waste drain water connection.
21
22
Attention
Make sure that water available is connected to a cold drinking water supply. If in doubt consult the installer for the possible installation of a water filter or water conditioner.
To gain full advantage from this unit in terms of performance and durability also make sure that:
Minimum water temperature is not lower than +5˚C and maximum water temperature does not exceed +40˚C.
23
24
Minimum water pressure is not below 1 bar and maximum water pressure does not exceed 5 bar.
The electrical suppy available corresponds to machine specifications as indicated on the unit nameplate.
25
The electrical isolator switch must be fitted with the correct fuse rating.
26
27
The minimum ambient temperature should not be lower than +10˚C and the maximum ambient temperature higher than +40˚C
There are no heat sources (kitchen ovens, grills) near the machine and the environment is not too humid.
28
Important
The machine installation has to be performed by Authorised Service Personnel
Connect the power lead to a suitable electrical supply
29
30
Check machine is level.
The level can be corrected by means of the levelling feet.
31
32
Make the connection to the water supply using the hoses supplied with the machine.
33
Water drain is connected and set-up properly using spiralled hose which should have a minimum fall of 3cm per metre.
start up
Open water shut-off valve.
35
Switch the main switch to the ON position.At this stage the unit will start up.
37
36
Plug in machine.
34
It is recommended that the interior of the storage bin is cleaned with an appropriate mild disinfectant solution.
The Authorised Service Agent will complete an inspection of the unit interior. The first batch of ice cubes will drop into the storage bin approximately 30 minutes from start-up.
The first batch of ice will be of poor quality but subsequent batches will be good quality.
38
39
Attention
If the temperature of the room in which the machine is placed is below +15˚C, the freezing cycle length will be shorter (17 to 20 minutes).
40
Alternatively, if the room temperature is above +30˚C, the freezing cycle length will be longer (25 to 30 minutes).
14
Loading...
+ 5 hidden pages