Fossil VD86A, VD85J, TY2723, TY2542, FL1331A Instruction Manual
...
123
For older movements, please contact Customer Care in your market.
Contact information is located on the Customer Care page of the website.
ANALOG
Date Models
Date Setting
1. Pull the crown out to position 2.
2. Turn the crown either clockwise or counter-clockwise and set the date for the previous day.
The direction that moves the date varies on different watch models.
Time Setting
1. Pull crown out to position 3.
2. Turn counter-clockwise to advance the time and continue until the day changes to the
present day.
3. Set to the correct time.
4. Push crown back to position 1.
Retrograde with Date Sweep VD86A / VD85J
Time and Date Setting
1. Pull crown out to position 3 and rotate clockwise to set day of week. Hand in upper
left indicates weekday and will automatically reset to “M” at the end of the week.
2. Keeping crown in position 3, rotate hands to set the time (make sure am/pm is
set correctly).
3. Push crown back to position 1.
4. Pull crown out to position 2 and rotate counter-clockwise to set date.
5. Push crown back to position 1.
WEEKDAY
SECOND HAND
ENGLISH
DATE
1 2 3
DATE
VD86A
WEEKDAY
SECOND HAND
VD85J
DATE
1 2 3
AUTOMATIC
Automatic Winding Movement
A timepiece fitted with an automatic winding movement obtains the power to wind itself by the movement of your wrist, there is no battery.
Therefore, not wearing the timepiece for several consecutive days could exhaust the power reserve. If your watch stops, it is recommended that
you manually wind the movement by rotating the crown clockwise to achieve the necessary power reserve.
It is important your timepiece is adjusted to match the size of your wrist. A loose fit may result in a loss in capacity of the timepiece to wind
itself. When fully wound, your timepiece has a power reserve of approximately 38 hours.
Automatic TY2723 / TY2542
1. To start time-keeping, rotate the crown clockwise 15-20 times in
position 1.
2. Pull crown out to position 2 and rotate clockwise to set time. Push
crown back to position 1.
TY2723
1 2
SECONDS
TY2542
POWER
RESERVE
1 2
SECONDS
revised 8 / 13
- 1 -
Automatic 2876
1. To start time-keeping, rotate the crown clockwise 15-20 times in position 1.
2. Pull crown out to position 2 and rotate clockwise to set hour and minute hands. 24-hour hand
moves with hour and minute hands. Use 24-hour hand to set correct am/pm time. Push crown
back to position 1.
3. Press A to adjust weekday. Each press of pusher A will advance the weekday by one increment.
4. Press B to adjust month. Each press of pusher B will advance the month by one increment.
5. Press C to adjust date. Each press of pusher A will advance the date by one increment.
NOTE: Do not set date between 10 p.m. and 2 a.m. (22 o’clock and 2 o’clock). Doing so
could damage the movement’s accuracy.
Automatic TY2714
1. To start time-keeping, rotate the crown clockwise in position 1 until power reserve hand
moves from “-” (low reserve) to “+” (full reserve).
2. Pull crown out to position 2 and rotate to set time. Return crown to position 1.
3. Press A to set date. Each press of pusher A will advance the date by one increment.
NOTE: Do not set date and week between 10 p.m. and 4 a.m. (22 o’clock and 4 o’clock).
Doing so could damage the movement’s accuracy.
ANALOG - DIGITAL
MONTH
WEEKDAY
24-HOUR HAND
POWER RESERVE
HOUR HAND
SECOND HAND
B
1 2
CA
MINUTE HAND
A
1 2
DATE
DATE
Ana-Digi FL1331A
Normal Time Display
1. Press A or B for EL.
2. Press and hold A or B for 2 seconds to turn digital display off. Press any pusher to turn on the
display when it is off.
3. Press C to toggle 12/24-hour format. Display will show “AM” or “PM” for 12-hour format.
4. Press D to change mode. Mode sequence is time, date, chronograph, alarm.
NOTE: In any setting mode, if no pusher is operated for 30 seconds, all changes will be saved
and the setting will automatically return to display mode.
Time and Calendar Setting
1. In normal time display or calendar display, press and hold C for 2 seconds, year will begin
flashing.
2. Press D to advance digits; press and hold D for fast advance.
3. Press C to advance to next setting value.
4. Setting sequence is: year, month, date, hour, minute, seconds.
5. Press C to exit setting mode.
NOTE: Weekday will automatically update upon exiting setting mode.
Chronograph Mode
1. Press D to change to chronograph mode.
2. Press D and hold 2 seconds to reset chronograph to zero.
3. Press C to start/stop the chronograph.
4. Press D to reset to zero.
Alarm Mode
1. Press D to change to alarm mode.
2. Press C to toggle alarm/chime on/off.
3. Alarm will sound at preset time for 20 seconds; press any pusher to silence alarm.
B
A
C
D
Alarm Setting
1. In alarm mode, press and hold C for 3 seconds; hour will begin flashing.
2. Press D to advance digit; press and hold D for fast advance.
3. Press C to set and advance to minute.
4. Press D to advance digit; press and hold D for fast advance.
5. Press C to exit setting mode.
- 2 -
Ana-Digi QFL133
Normal Time Display
1. Press A to change mode. Mode sequence is normal time display, alarm, chronograph, and
time/calendar setting.
2. Press B for EL.
3. Press C to toggle 12/24-hour time.
NOTE: In any setting mode, if no pusher is operated for 2 minutes, all changes will be saved
and the setting will automatically return to normal time display.
Time and Calendar Setting
1. Press A to change to time/calendar setting mode; seconds will begin flashing.
2. Press C to set seconds to zero.
3. Press D to advance to next setting value.
4. Press C to increase digit, press and hold C for fast advance.
5. Setting sequence is: seconds, hour, minute, month, date and weekday.
6. Press A to exit setting mode.
Alarm Mode
1. Press A to change to alarm mode.
2. Press C to toggle alarm/chime on/off.
3. Alarm will sound at preset time for 20 seconds; press C or D to silence alarm.
Alarm Setting
1. In alarm mode, press D to enter setting mode; hour will begin flashing.
2. Press C to increase hour; press and hold C for fast advance.
3. Press D to set and advance to minutes.
4. Press C to increase minutes; press and hold C for fast advance.
5. Press D to save data and exit setting mode; press A to save data, exit setting mode, and return
to normal time display.
Chronograph Mode
1. Press A to change to chronograph mode.
2. Press C to start/stop the chronograph.
3. Press D to reset to zero.
B
A
C
D
Split Time
1. Press D while the chronograph is running for split time.
2. Press D again to return to chronograph.
3. Repeat steps 1 and 2 to measure multiple split times.
4. Press C to finalize timing.
5. Press D to reset to zero.
- 3 -
World Time Module (Analog-Digital and Digital)
A
B
D
C
Normal Time Display
1. Press pusher B for EL.
2. Press pusher C for hourly chime on/off.
3. Press pusher D for DST on/off for the selected city.
4. In any mode or setting, if no pusher is operated for 60 seconds, setting will be returned to normal time display.
B
A
C
D
Time and Calendar Mode
1. Press and hold pusher B for 2 seconds to enter setting mode. 12/24 hour time will begin flashing.
B
2. Press pusher C to select 12/24 hour time.
3. Press pusher A to select and change seconds, minute, hour, year, month, day and city.
4. Press pusher C to increase the digit; press pusher D to decrease the digit.
5. Press pusher B to exit setting mode.
A
World Time Mode
1. Press pusher A to select world time mode.
2. Press pusher C to select city.
3. Press pusher D for DST on/off for the selected city.
Words City Hour Difference Words City Hour Difference
MDY
HNL
ANC
LAX
DEN
CHI
NYC
CCS
RIO
-2H
-1H
LON
Midway
Honolulu
Anchorage
Los Angeles
Denver
Chicago
New York
Caracas
Rio de Janeiro
-2H
-1H
London
-11 hours
-10 hours
-9 hours
-8 hours
-7 hours
-6 hours
-5 hours
-4 hours
-3 hours
-2 hours
-1 hour
0 hours
PAR
CAI
MOW
DXB
KHI
DAC
BKK
HKG
TYO
SYD
NOU
AKL
Paris
Cairo
Moscow
Dubai
Karachi
Dacca
Bangkok
Hong Kong
Tokyo
Sydney
Noumea
Auchland
+1 hour
+2 hours
+3 hours
+4 hours
+5 hours
+6 hours
+7 hours
+8 hours
+9 hours
+10 hours
+11 hours
+12 hours
Alarm Setting (3 alarms)
1. Press pusher A to select alarm mode.
2. Press pusher C to scroll through alarms.
3. Press pusher D for alarm on/off.
4. Press and hold pusher B for 2 seconds to enter setting mode. Minutes will begin flashing.
5. Press pusher A to select minutes and hour.
6. Press pusher C to increase the digit; press pusher D to decrease the digit. Alarm is automatically turned on when setting is changed.
7. Press pusher B to exit setting mode.
C
D
Chronograph Mode
1. Press pusher A to select chronograph mode (STW).
2. Press pusher C to start chronograph; press pusher D to stop chronograph.
3. Press pusher D to reset chronograph when it is not running.
Lap Counting
1. Press pusher C while chronograph is running (will record up to 20 laps).
2. Press pusher D to finalize timing.
3. Press pusher A to recall laps (TOT) when information is recorded in the chronograph (will recall up to 20 laps).
4. Press pusher C to view next lap; press pusher D to view previous lap.
5. Enter regular chronograph mode; press pusher D to reset to zero.
Countdown Timer
1. Press pusher A to select timer mode.
2. Press pusher C to start/stop the timer.
3. Press pusher D to reset timer when it is not running. Timer will show all zero’s before timer is started again.
4. Press and hold pusher B for 2 seconds to enter setting mode. Seconds will begin flashing.
5. Press pusher A to select seconds, minutes and hour.
6. Press pusher C to increase digit; press pusher D to decrease digit.
7. Press pusher B to exit setting mode.
- 4 -
MULTIFUNCTION
Multi-Time Zone 505.24H
Time / Calendar Setting
1. Pull RED crown B (at 4:00 position) out to position 2.
2. Turn crown clockwise to set to previous day’s date.
3. Pull crown out to position 3.
4. Turn crown counter-clockwise until date changes to today’s date; set correct a.m. or p.m. time.
5. Return crown to position 1.
NOTE: Second time zone hand will move in conjunction with hour and minute hands. Set hour
and minute hands before setting second time zone.
Second Time Zone Setting
1. Pull RED crown B (at 4:00 position) out to position 2.
2. Turn crown counter-clockwise to set second time zone.
3. Return crown to position 1.
NOTE: Second time zone hand is read in military time, indicated on the bezel.
Third Time Zone Reading
1. Turn crown A clockwise or counter-clockwise to match current hour with current city time zone.
2. For third time zone reading, locate the city indicating the new time zone. Each increment (to
the right) indicates +1 hour; each decrement (to the left) indicates -1 hour.
Multifunction 6P25
Date Setting
1. Pull crown out to position 2.
2. Turn counter-clockwise to select date.
SECOND TIME
ZONE HAND
1
A
2
3
DATE
DAY
B
Day and Time Setting
1. To set time, pull crown out to position 3.
2. Turn clockwise to set hour and minute hands.
move with the hour and minute hands.
The hand showing days of the week will also
Keep turning until you have reached the desired day.
3. Push crown back to position 1.
Multifunction VX3R / VX3RE
Time Setting
1. Pull crown out to position 2.
2. Turn crown clockwise to set time.
3. Return crown to position 1.
NOTE: 24-hour hand moves correspondingly with the hour and minute hands. When setting
the time be sure to check that the 24-hour hand is set properly.
Date Setting
1. Pull crown out to position 3. Turn crown counterclockwise to set date.
2. Return crown to position 1.
24-HOUR
1
2
3
1 2 3
DATE
- 5 -
Loading...