Foscam FosBaby, FosBaby P1 Quick Installation Manual

.00
95.00mm
190.00mm
285.00mm
380.00mm
475.00mm
570.00mm
142.5mm
.00
Wi-Fi Light Description
O No Wi-Fi connection
Flashing every 0.1 seconds Soft AP takes eect
Flashing every 0.2 seconds EZLink takes eect (default)
Flashing every 0.4 seconds WPS is connecting
1.1 Physical Description
Please Note:
If required, the Fosbaby camera can also be powered using portable or mobile power sources. We suggest an output of 5V/2A and a capacity of 5000 mAH. Under ideal conditions this will provide about 5 hours of use.
We do not recommend the use of a PC or Laptop power source due to their insucient current strength. Use of these power supplies may result in damage or inconsistent functioning of your Fosbaby camera.
Before you continue, please note:
Make sure your smartphone is located near the Fosbaby camera.
Your smartphone should be connected to the same Wi-Fi network as your fosbaby camera.
After plugging the Fosbaby P1 to the power supply, the FosBaby P1 will automatically run, cruise startup (Fosbaby P1 only).
Lens
Microphone
Soft AP
WPS / Reset
WPS/Reset
Soft AP
Please Note:
If you used snapshot by the remote control, the default storage path of snapshot les are FTP server and SD card.
Remote Control Description:
One Key Alert on
One Key Alert o
Speaker Volume Up
Speaker Volume Down
Left control
Snapshot
Night Lamp
Play/Stop Lullabies
Up Control
Right Control
Down Control
WPS
Wireless Router
STRANGULATION HAZARD!
Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3ft(0.9m)away). Do not remove this tag.
WARNING:
Power
Speaker
Temperature & Humidity Detection Sensor
Night Lamp
Micro-SD Card Slot
Wi-Fi & System Status Light
STRANGULATION
HAZARD!
Children have
STRANGLED in cords. Keep this cord out of the reach of children (more than 3ft(0.9m)away). Do not remove this tag.
WARNING:
Warning Sticker
Wi-Fi Status Light
V1.8
EQFB0012
Quick Installation Guide
Wireless HD Baby Monitor
FosBaby FosBaby P1
"Foscam" App download
Lens
Microphone
Soft AP
WPS / Reset
STRANGULATION
HAZARD!
Children have
STRANGLED in cords. Keep this cord out of the reach of children (more than 3ft(0.9m)away). Do not remove this tag.
WARNING:
Temperature Detection Sensor
Speaker
Micro-SD Card Slot
Power
Power
Wi-Fi Status Light
Warning Sticker
Wireless Router
WPS
FosBaby
FosBaby P1
1Hardware Introduction
Package Contents
Power Adapter
Mounting Bracket
IP Camera
USB Power Cable
Remote Control (Fosbaby P1 only)
Watch strap
Temperature Detection Sensor
Quick Installation Guide
CD-ROM
Warranty Card
Warning Sticker
Quick Installation Guide
HD Wireless Baby Monitor
FosBaby FosBaby P1
"Foscam" App download
.00
95.00mm
190.00mm
285.00mm
380.00mm
475.00mm
570.00mm
142.5mm
.00
5 Technical Support
1.2 Hardware Installation
2 Add the IP Camera
3 Access the IP Camera
4 FAQ
Forgot Username / Password
Restore camera back to factory settings:
1. Press and hold the "Reset" button on the camera for about 10 seconds with the camera powered on, and then release.
2. Once the button is released, wait about 30 seconds, and the FosBaby will automatically restart, cruise startup, and then restore itself to its Factory Settings. The username and password will be set to the default username and password.
Please Note:
After restoring to factory default settings, you need
to re-congure the Wi-Fi connection. You can follow
the Setup Wizard of the App to congure your Wi-Fi
connection again.
If your device fails to connect to the Wi-Fi using the Setup Wizard, you can also use WPS mode or the Soft AP connection. Please refer to the User Manual on the Foscam website at http://www.foscam.com .
You can add the Foscam IP Camera using a Smartphone.
1.
Download the App
If you have a QR Code scanning app on your phone, please use it to scan the QR code on the front cover of this Quick Installation Guide. This will take you to the download page to install the Foscam App.
The App icon will be displayed below after it is installed successfully:
Please Note:
If you do not have a QR code app on your phone, you can simply go to the App Store or Google Play Store and search the term "Foscam". Find the app that appears with the same icon as shown above, and download it to your device. Ensure that you download the App created by our ShenZhen Foscam Intelligent Technology Co. LTD.
2. Add the IP Camera
Run the App, and then register for a Foscam account. Once logged in, you can tap the "+" button on the App and follow the setup wizard to add your camera.
You can also access your Foscam camera via our P2P web portal: https://www.myfoscam.com on your Windows PC using Internet Explorer.
If you have registered and added the IP Camera on the Foscam App, you don't have to register again. Rather, just log in and access the camera directly via the app or browser.
Shortcut icon for Windows OS
Shortcut icon for Mac OS
As an alternative to accessing the camera via the P2P web portal, you can access the camera directly through the local network and remotely via port forwarding. Please download the "IP Camera Search Tool" from http://www.foscam.com .
Place the Fosbaby camera directly on a desk (nomounting bracket required).
Install your Fosbaby camera on the wall (with the supplied mounting bracket).
If you have problems with your Foscam IP Camera, please contact the Foscam reseller who you purchased your carema from, Alternatively you can e-mail the Foscam’s technical support team: tech@foscam.com.
Your valuable comments and suggestions on improving Foscam products are welcomed!
ShenZhen Foscam Intelligent Technology Co., Ltd
www.foscam.com
Take advantage of our provided watch strap for easy fastening! The strap will allow you to fasten your Fosbaby in an otherwise challenging location (i.e. Crib, Wall bracket, etc.).
Please note:
The Fosbaby camera should always be fastened out of your child’s reach.
Loading...