Fortress Technologies AS/400 Installation And Service Manual

Download

Page 1

AS/400

UPS Installation and Service Guide

UPS — Guide d’installation et d’entretien

Installations- und Wartungsanleitung für die USV

Manual de instalación y reparación del UPS

Guida per l’installazione e la manutenzione dell’UPS

Guia de Instalação e Manutenção do UPS

Contents

Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

AS/400 9401, 9402/9404 UPS IBM Service Support . . . . . . . . . . . . . . . . . . . . . . . . .28

UPS Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Changing the Fortress’ Inverter Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Page 2

IMPORTANT SAFETY INSTRUCTIONS — SAVE THESE INSTRUCTIONS

If you have an extended battery time unit (a unit with separate battery packs), read the warnings below before you go to step 1.

CAUTION

The batteries used in the UPS and battery pack(s) can produce dangerous voltage and high current. The batteries may cause severe injury if their terminals contact a tool or the battery pack’s cabinet. Be very careful to avoid electrical shock and burns from contacting battery terminals while you put in a battery drawer or connect the battery pack(s). Using batteries not supplied by Best Power invalidates any Best Power service agreement.

1.Batteries contain caustic acids and toxic materials and can rupture or leak if mistreated. Remove rings and metal wristwatches or other jewelry. Don’t carry metal objects in your pockets; these objects could fall into the UPS.

2.At no time can any tools be allowed to contact a battery terminal and the UPS cabinet or another battery terminal. Do not lay tools or metal parts on top of batteries.

3.When you connect the battery pack cables, never allow the metal inside the connector to touch a battery’s terminals or the UPS cabinet.

4.Install the battery cables so they cannot be pinched by the UPS cabinet or a battery pack’s cabinet.

5.The green “Grounding Electrode Terminal” bolt on the back of 1.3K models must be connected to the green bolt on the back of each battery pack. This connects the battery pack’s chassis ground (or earth) to the UPS chassis ground (or earth).

6.Protect the battery cables from physical damage.

Contents

Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

AS/400 9401, 9402/9404 UPS IBM Service Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

UPS Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Changing the Fortress’ Inverter Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Page 3

Startup

English

Please follow the steps on the next few pages to start your Fortress.

Look at the back of the UPS and compare it to the UPS drawings.

For A:Go to step 9. For B:Go to step 9. For C:If the UPS has a separate battery pack, go to step 2; if not, go to step 9. For D:If the UPS has a separate battery pack, go to step 5; if not, go to step 9.

Français

Suivez les étapes indiquées dans les pages suivantes pour mettre votre Fortress en marche.

Observez l’arrière de l’UPS et comparez-le aux schémas.

Pour A : Passez à l’étape 9. Pour B : Passez à l’étape 9. Pour C : Si l’UPS a un bloc de batteries séparé, passez à l’étape 2; sinon, passez à l’étape 9. Pour D : Si l’UPS a un bloc de batteries séparé, passez à l’étape 5; sinon, passez à l’étape 9.

A B C D

Deutsch

Bitte führen Sie vor dem Start Ihrer Fortress die auf den nächsten Seiten beschriebenen Schritte durch.

Sehen Sie sich die Rückseite der USV an, und vergleichen Sie sie mit den Abbildungen der USV.

Für A:Machen Sie mit Schritt 9weiter. Für B:Machen Sie mit Schritt 9weiter. Für C:Wenn die USV ein separates Batterie-Paket hat, machen Sie mit Schritt 2weiter; wenn nicht,

machen Sie mit Schritt 9weiter.

Für D:Wenn die USV ein separates Batterie-Paket hat, machen Sie mit Schritt 5weiter; wenn nicht,

machen Sie mit Schritt 9weiter.

Español

Por favor siga los pasos que se indican en las siguientes páginas para poner en marcha su Fortress.

Mire la parte posterior del UPS y compárela con los dibujos del UPS.

Para A:Vaya al paso 9. Para B:Vaya al paso 9. Para C:Si el UPS tiene un paquete de baterías separado, vaya al paso 2; si no lo tiene, vaya al paso 9. Para D:Si el UPS tiene un paquete de baterías separado, vaya al paso 5; si no lo tiene, vaya al paso 9.

Italiano

Prima di iniziare ad usare il Fortress, compiere le operazioni indicate nelle pagine seguenti.

Guardare sul retro dell’UPS e confrontarlo con le quattro illustrazioni.

Se l’UPS appare come nell’illustrazione A:proseguire al punto 9. Se appare come nell’illustrazione B: proseguire al punto 9. Se appare come nell’illustrazione C: se l’UPS è provvisto di un blocco batterie separato, proseguire al punto

2, altrimenti proseguire al punto 9.

Se l’UPS appare come nell’illustrazione D: se l’UPS è provvisto di un blocco batterie separato, proseguire al

punto 5, altrimenti proseguire al punto 9.

Português

Siga as etapas contidas nas próximas páginas para iniciar o funcionamento do Fortress.

Observe a parte posterior do UPS e compare-a com os quatro desenhos abaixo.

No caso A: Avance para a etapa 9. No caso B: Avance para a etapa 9. No caso C: Se o UPS tiver um conjunto de baterias independente, passe para a etapa 2; de contrário, avance

para a etapa 9.

No caso D: Se o UPS tiver um conjunto de baterias independente, passe para a etapa 5; de contrário, avance

para a etapa 9.

Page 4

English

Connecting LI 675 and 750 Battery Packs: Steps 2-4

Steps 2-4 are for LI 675 and 750 models with separate battery packs. First, place the UPS near the equipment it will protect, and place the battery pack(s) (2) next to the UPS (1). Leave at least 3 inches (80 mm) space for ventilation on each side of the UPS, behind the UPS, and on the sides of each battery pack.

1 2

Français

Raccordement des blocs de batteries LI 675, 750 : étapes 2-4

Les étapes 2-4 s’appliquent aux modèles LI 675 et 750 à blocs de batteries séparés. Commencez par placer l’UPS à proximité de l’équipement à protéger, et placez le(s) bloc(s) [2] de batteries près de l’UPS (1). Laissez un espace d’au moins 80 mm pour la ventilation de chaque côté de l’UPS, derrière l’UPS et des deux côtés côtés de chaque bloc de batteries.

Deutsch

Wie Sie die Batterie-Pakete für Modelle LI 675, 750 anschließen: Schritt 2-4

Die Schritte 2-4 beziehen sich auf die Modelle LI 675 und 750 mit separaten Batterie-Paketen. Stellen Sie die USV als erstes in der Nähe der Geräte auf, die sie schützen soll, und stellen Sie das bzw. die BatteriePakete (2) neben die USV (1). Lassen Sie auf beiden Seiten der USV, hinter der USV und auf den Seiten der Batterie-Pakete zur Lüftung einen Freiraum von mindestens 80 mm.

Español

Conexión de los paquetes de baterías LI 675, 750: Pasos 2-4

Los pasos 2-4 son para los modelos LI 675 y 750 con paquetes de baterías separadas. Primero, coloque el UPS cerca del equipo que va a proteger, y coloque el(los) paquete(s) de baterías (2) junto al UPS (1). Deje por lo menos 3 pulgadas (80 mm) de espacio libre para ventilación a cada lado del UPS, detrás del UPS, y a los lados de cada paquete de baterías.

Italiano

Collegamento dei blocchi batteria LI 675, 750: Operazioni 2-4

Le operazioni 2-4 si riferiscono ai modelli LI 675 e LI 750 con blocchi batteria separati. Innanzitutto collocare l’UPS vicino all’unità da proteggere e collocare il blocco o i blocchi batteria (2) vicino all’UPS (1). Lasciare almeno 80 mm di spazio per la ventilazione su ciascun lato dell’UPS, dietro l’UPS e sui lati di ciascun blocco batteria.

Português

Conexão do jogos de baterias LI 675, 750: etapas 2 a 4

As etapas 2 a 4 correspondem aos modelos LI 675 e 750 com jogos de baterias independentes. Primeiro, coloque o UPS próximo ao equipamento que irá proteger, e coloque o(s) jogo(s) de bateria(s) (2) próximo ao UPS (1). Deixe um espaço de pelo menos 80 mm para fins de ventilação de cada lado do UPS, atrás do mesmo e dos lados de cada jogo de baterias.

Page 5

English

Before you can plug the battery cables into the UPS, you must remove the plate over the UPS’ connector by removing the two screws in the plate. Then, plug the battery cables from the nearest battery pack into the matching connector on the UPS as shown.

Français

Avant de brancher les câbles de batteries dans l’UPS, retirez la plaque située au-dessus du connecteur en enlevant les deux vis de la plaque. Maintenant, branchez les câbles de batteries du bloc de batteries le plus proche dans le connecteur correspondant de l’UPS, comme indiqué.

Deutsch

Bevor Sie die Batteriekabel in die USV einstecken, müssen Sie die Abdeckung des Anschlusses der USV entfernen, indem Sie die beiden Schrauben der Abdeckung herausschrauben. Stecken Sie die Batteriekabel des Batterie-Pakets, das am nähesten zur USV steht, wie abgebildet in den entsprechenden Anschluß der USV.

Español

Antes de enchufar los cables de la batería en el UPS, debe sacar la placa que está sobre el conector del UPS sacando los dos tornillos de la placa. Ahora enchufe los cables de las baterías del paquete de baterías más cercano al conector correspondiente en el UPS, tal como se muestra.

Italiano

Prima di poter collegare i cavi delle batterie nell’UPS è necessario, rimuovendo le due viti, togliere la piastra posta sul connettore dell’UPS. Collegare quindi i cavi delle batterie, dal blocco batteria più vicino, al connettore accoppiato sull’UPS, come mostrato nell’illustrazione.

Português

Antes de poder ligar os cabos da bateria ao UPS, será necessário retirar a placa situada sobre o

dispositivo de ligação do UPS, desapertando os dois parafusos existentes. Conecte em seguida, os cabos

do jogo de baterias mais próximo no conector correspondente do UPS, conforme apresentado.

Page 6

English

If you have more than one battery pack, go to the battery pack you have already connected to the UPS.

Find the metal plate in the upper left corner of the back panel. Remove the screws in the plate; then, remove the plate. You should now see a battery connector. Plug the battery cables from the nextbattery pack into the connector you uncovered on the firstbattery pack as shown. Repeat this step for each additional battery pack. Go to step 9.

Français

Si vous avez plus d’un bloc de batteries, allez vers le bloc de batteries que vous avez déjà relié à l’UPS. Cherchez la plaque métallique au coin supérieur gauche du panneau arrière. Retirez les vis qui maintiennent la plaque, puis la plaque elle-même. Vous devriez apercevoir un connecteur de batteries. Branchez les câbles de batteries du bloc de batteries suivant dans le connecteur que vous avez découvert sur le premier bloc de batteries, comme indiqué. Répétez cette étape pour chaque bloc de batteries supplémentaire. Passez à l’étape 9.

Deutsch

Wenn Sie mehr als ein Batterie-Paket haben, machen Sie mit dem Batterie-Paket weiter, das Sie bereits an

die USV angeschlossen haben. Oben links auf der Rückwand befindet sich eine Metallplatte. Entfernen Sie die Schrauben auf dieser Platte, und nehmen Sie die Platte ab. Stecken Sie die Batteriekabel des nächsten Batterie-Pakets wie abgebildet in den Anschluß, den Sie auf dem ersten Batterie-Paket freigelegt haben. Wiederholen Sie diesen Schritt für jedes zusätzliche Batterie-Paket. Machen Sie mit Schritt 9 weiter.

Español

Si tiene más de un paquete de baterías, en el paquete de baterías que ya conectó al UPS, busque la placa

metálica en la esquina superior izquierda del panel trasero. Quite los tornillos de la placa, luego, quite la placa. Ahora debe poder ver un conector de baterías. Enchufe los cables de batería del siguiente paquete de baterías en el conector que acaba de destapar ubicado en el primer paquete de baterías, tal como se muestra. Repita este paso para cada paquete adicional de baterías. Continúe en el paso 9.

Italiano

Se avete a disposizione più di un blocco batteria, prendere quello che avete già collegato all’UPS. Trovare

la piastra metallica nell’angolo superiore sinistro del pannello sul retro. Rimuovere le viti nella piastra e rimuovere la piastra. Dovreste ora riuscire a vedere un connettore di batteria. Inserire i cavi della batteria, dal prossimo blocco batteria, al connettore che avevate scoperto sul primo blocco, come mostrato nell’illustrazione. Ripetere questa operazione per ciascun blocco batteria supplementare. Compiere le

operazioni indicate al punto 9.

Português

Se tiver mais de um jogo de baterias, passe para aquele que já tiver conectado ao UPS. Procure a chapa

de metal no canto superior esquerdo no painel traseiro, retire os parafusos da chapa; em seguida, retire a chapa. Você verá agora o conector de bateria. Conecte os cabos do próximo jogo de baterias ao conector que você tiver aberto no primeiro jogo de baterias, conforme mostrado. Repita esta etapa para cada jogo de baterias adicional. Passe para a etapa 9.

Page 7

English

Connecting LI 1.3K Battery Packs: Steps 5-8

Steps 5-8 are for LI 1.3K models with separate battery packs. First, place the UPS and battery packs near the equipment the UPS must protect. If you have one battery pack, you can place it next to the UPS or stack the UPS on top of it. If you have two or three battery packs, arrange them as shown. Leave at least 3 inches (80 mm) space for ventilation on each side of the UPS, behind the UPS, and on the sides of each battery pack.

Français

Raccordement des blocs de batteries LI 1.3 K : étapes 5-8

Les étapes 5-8 s’appliquent aux modèles LI 1.3 K avec blocs de batteries séparés. Commencez par placer

l’UPS et les blocs de batteries à proximité de l’équipement que doit protéger l’UPS. Si vous avez un bloc de

batteries, vous pouvez le placer soit à proximité de l’UPS, ou poser l’UPS sur le bloc. Si vous avez deux ou

trois blocs de batteries, disposez-les comme indiqué. Laissez un espace d’au moins 80 mm pour la

ventilation de chaque côté de l’UPS, derrière l’UPS, et sur les côtés de chaque bloc de batteries.

Deutsch

Wie Sie die Batterie-Pakete für Modell LI 1.3K anschließen: Schritt 5-8

Die Schritte 5-8 beziehen sich auf die Modelle LI 1.3K mit separaten Batterie-Paketen. Stellen Sie die USV und die Batterie-Pakete als erstes in der Nähe der Geräte auf, die sie schützen soll. Wenn Sie ein BatteriePaket haben, können Sie es neben die USV stellen oder die USV auf das Paket stellen. Wenn Sie zwei oder drei Batterie-Pakete haben, stellen Sie sie wie abgebildet auf. Lassen Sie auf beiden Seiten der USV, hinter der USV und auf den Seiten der Batterie-Pakete zur Lüftung einen Freiraum von mindestens 80 mm.

Español

Conexión de los paquetes de baterías LI 1.3K: Pasos 5-8

Los pasos 5-8 son para los modelos LI 1.3K con paquetes de baterías separadas. Primero, coloque el UPS y los paquetes de baterías cerca del equipo que el UPS va a proteger. Si tiene un paquete de baterías, puede colocarlo junto al UPS o colocar el UPS sobre el paquete de baterías. Si tiene dos o tres paquetes de baterías, organícelos tal como se muestra. Deje por lo menos 3 pulgadas (80 mm) de espacio libre para ventilación a cada lado del UPS, detrás del UPS, y a los lados de cada paquete de baterías.

Italiano

Collegamento dei blocchi batteria LI 1.3K: Operazioni 5-8

Le operazioni 5-8 si riferiscono ai modelli LI 1.3K con blocchi batteria separati. Innanzitutto collocare l’UPS e i blocchi batteria vicino all’unità da proteggere. Se avete un blocco batteria, potete collocarlo accanto all’UPS o accatastare l’UPS sopra ad esso. Se avete due o tre blocchi batteria, disporli come indicato nell’illustrazione. Lasciare almeno 80 mm di spazio per la ventilazione su ciascun lato dell’UPS, dietro l’UPS e sui lati di ciascun blocco batteria.

Português

Conexão dos jogos de baterias LI 1.3K: etapas 5 a 8

As etapas 5 a 8 correspondem aos modelos LI 1.3K com jogos de baterias independentes. Primeiro, coloque o UPS e o jogos de baterias próximos ao equipamento que irá proteger. Se tiver um jogo de baterias, pode colocá-lo próximo ao UPS ou colocar o UPS sobre o mesmo. Se tiver dois ou três jogos de bateria, coloque-os conforme mostrado. Deixe um espaço de pelo menos 80 mm para fins de ventilação de cada lado do UPS, atrás do mesmo e dos lados de cada jogo de baterias.

Page 8

English

Read the caution below; then, remove the two screws shown (1) from the back of your UPS. Fit the battery drawer (2) into the opening in the back of the Fortress. Slide the drawer all the way in. To fasten the drawer, put the two screws into the back of the UPS as shown, and tighten them with a Phillips screwdriver.

Français

Lisez le signal ci-dessous, puis retirez les deux vis indiquées (1) à l’arrière de votre UPS. Insérez le tiroir (2) à batteries dans l’ouverture à l’arrière du Fortress. Faites glisser le tiroir à fond. Pour le maintenir en place, remettez les deux vis à l’arrière de l’UPS, comme indiqué et serrez-les avec un tournevis Phillips.

Deutsch

Lesen Sie sich zuerst die nachstehenden Sicherheitshinweise durch, und entfernen Sie dann die beiden Schrauben (1) auf der Rückwand Ihrer USV. Setzen Sie den Batterie-Einschub (2) in die Öffnung auf der Rückseite der Fortress ein und schieben Sie ihn vollständig hinein. Um den Einschub zu befestigen, stecken Sie die beiden Schrauben wie abgebildet in die Rückwand der USV und ziehen Sie sie mit einem Kreuzschlitzschraubenzieher fest.

Español

Lea el aviso de precaución que se indica a continuación, luego, quite los dos tornillos que se muestran (1) de la parte posterior del UPS. Encaje el cajón de baterías (2) en la abertura que se encuentra en la parte posterior del Fortress. Deslice el cajón hasta adentro. Para sujetar el cajón, coloque los dos tornillos en la parte posterior del UPS tal como se muestra, y apriételos con un destornillador Phillips.

Italiano

Leggere l’avvertimento sotto indicato e rimuovere poi le due viti mostrate (1) dal retro dell’UPS. Inserire il cassetto delle batterie (2) nell’apertura situata posteriormente al Fortress. Far scorrere il cassetto fino in fondo. Per fissare il cassetto, inserire le due viti sul retro dell’UPS, come mostrato nell’illustrazione, e stringerle con un cacciavite a croce.

Português

Leia o aviso abaixo, em seguida, retire os dois parafusos mostrados (1) da parte de trás do UPS. Encaixe a gaveta da bateria (2) na abertura da parte de trás do Fortress. Empurre a gaveta até o final. Para prender a gaveta, coloque os dois parafusos na parte de trás do UPS conforme mostrado. Em seguida, aperte-os com uma chave Phillips.

ACHTUNG:

Die Metallteile der Batterien nicht berühren und darauf achten, daß der Schraubenzieher nicht mit den Batterien in Kontakt kommt. Sollte eine Batterie auslaufen, wenden Sie sich bitte an Ihre lokale BEST-Niederlassung; die Flüssigkeit, die aus der Batterie ausstritt, enthält Säure, die Verbrennungen verursachen kann.

CAUTION

Do not touch the metal on the batteries, and do not let the screwdriver contact the batteries. If a battery is leaking, call your local Best Power office; the liquid leaking from the batteries contains acid that causes burns.

ATTENTION :

ne touchez pas les parties métalliques des batteries et ne laissez pas le tournevis toucher ces dernières. Si une batterie présente une fuite, appelez votre distributeur Best Power local ; le liquide qui s’échappe des batteries contient un acide qui provoque des brûlures.

PRECAUCIÓN:

No toque el metal de las baterías y no permita que el destornillador tenga contacto con las baterías. Si una batería tiene fugas, llame a su oficina local Best Power; el líquido que sale de las baterías contiene un ácido que produce quemaduras.

! Avvertimento:

Non toccare il metallo delle batterie e non fate in modo che il cacciavite venga a contatto con le batterie. Se la batteria perde liquido, telefonare all’ufficio Best Power locale. Il liquido che fuoriesce dalla batteria contiene acido che causa bruciature.

Atenção:

não toque no metal das baterias e não deixe que a chave de fenda entre em contato com as baterias. Se a bateria estiver vazando, ligue para o escritório Best Power local; o líquido que vaza da bateria contém ácido, e pode causar queimaduras.

1 1

Page 9

English

Find the green bolt labeled “Grounding Electrode Terminal” on the back of the UPS. Remove this bolt using a standard screwdriver or 5/16-inch (8 mm) wrench. On the back of each battery pack, find the green bolt with a wire attached. The unconnected end of the wire should have a ring connector. Put the ring connector from each battery pack on the bolt you removed from the UPS. Then, put the bolt back into the UPS and tighten it.

Français

Cherchez le boulon vert marqué “Borne d’électrode de mise à la masse” (Grounding Electrode Terminal) à l’arrière de l’UPS. Retirez ce boulon à l’aide d’un tournevis ordinaire 8 mm ou d’une clé anglaise. Cherchez le boulon vert auquel est fixé un fil à l’arrière de chaque bloc de batteries. L’extrémité non reliée du fil devrait porter une bague deconnexion. Mettez la bague de connexion de chaque bloc de batteries sur le boulon que vous avez enlevé de l’UPS. Puis remettez le boulon dans l’UPS ; serrez.

Deutsch

Auf der Rückseite der USV befindet sich eine grüne Erdungsschraube mit der Aufschrift „Anschlußklemme für Masseleitung“ (Grounding Electrode Terminal). Entfernen Sie diesen Erdungsschraube mit einem normalen Schraubenzieher oder 8 mm Schraubenschlüssel. Auf der Rückseite der Batterie-Pakete befindet sich ebenfalls ein grüner Bolzen, an den ein Draht angeschlossen ist. Das freie Ende des Drahtes ist mit einem Ringstecker ausgestattet. Bringen Sie den Ringstecker der Batterie-Pakete an der Erdungsschraube an, den Sie von der USV entfernt haben, stecken Sie die Erdungsschraube wieder in die USV und ziehen Sie ihn fest.

Español

Localice el perno verde marcado “Terminal del electrodo de conexión a tierra” (Grounding Electrode Terminal) en la parte posterior del UPS. Quite este perno usando un destornillador estándar 8 mm o llave inglesa. En la parte posterior de cada paquete de baterías, localice el perno verde que tiene un alambre conectado. El extremo suelto del alambre debe tener un conector de anillo. Coloque este conector de anillo de cada paquete de baterías en el perno que quitó del UPS. Luego ponga el perno otra vez en el UPS y apriételo.

Italiano

Trovare il bullone verde contrassegnato “Terminale dell’elettrodo della messa a terra” (Grounding Electrode Terminal) sul retro dell’UPS. Rimuovere questo bullone usando un cacciavite standard 8 mm o un’avvitatrice. Sul retro di ciascun blocco batteria, trovare il bullone verde con un filo attaccato. L’estremità del filo non collegato dovrebbe essere munita di un connettore ad anello. Collocare il connettore ad anello, situato su ciascun blocco batteria, sul bullone che avete rimosso dall’UPS. Dopo aver effettuato questa operazione, ricollocare il bullone nell’UPS e stringerlo.

Português

Encontre o parafuso verde identificado como “terminal do eletrodo terra” (Grounding Electrode Terminal) na parte de trás do UPS. Retire este parafuso usando uma chave de fenda 8 mm ou chave de boca comum. Na parte de trás de cada jogo de baterias você encontrará um parafuso verde com um fio ligado ao mesmo. A extremidade não conectada do fio deverá ter um conector em forma de anel. Coloque o conector de anel de cada jogo de baterias no parafuso que tiver retirado do UPS. Em seguida, coloque o parafuso de volta no UPS e aperte-o.

Page 10

English

A. One Battery Pack: If your UPS has one battery pack, connect the cables from that battery pack to the Fortress as shown in parts 1 and 2 of the drawing; part 1 shows the connection between the UPS and the battery pack, and part 2 shows a closeup of the connectors from the UPS and the battery pack. Next, use the metal plate and bolt you received to lock the two connectors as shown in part 3 of the drawing.

1 2

Français

A. Un bloc de batteries : Si votre UPS a un bloc de batteries, reliez les câbles de ce bloc de batteries au

Fortress, comme indiqué sur les dessins 1 et 2 ; le dessin 1 montre la connexion entre l’UPS et le bloc de

batteries et le dessin 2 montre une vue rapprochée des connecteurs de l’UPS et du bloc de batteries. Puis

utilisez la plaque métallique et le boulon fournis pour verrouiller les deux connecteurs comme indiqué sur le

dessin N3.

Deutsch

A. Ein Batterie-Paket: Wenn Ihre USV ein Batterie-Paket hat, schließen Sie die Kabel von diesem BatteriePaket wie in Teil 1 und 2 der Zeichnung abgebildet an die Fortress an. In Teil 1 ist die Verbindung zwischen der USV und dem Batterie-Paket und in Teil 2 sind die Steckverbinder der USV und des Batterie-Pakets zu sehen. Benutzen Sie dann die Metallplatte und die beiliegenden Schrauben, um die beiden Steckverbinder, wie in Teil 3 der Zeichnung abgebildet, festzumachen.

Español

A. Un paquete de baterías: Si su UPS tiene un paquete de baterías, conecte los cables de ese paquete

de baterías en el Fortress tal como se muestra en las partes 1 y 2 del dibujo; la parte 1 muestra la

conexión entre el UPS y el paquete de baterías, y la parte 2 muestra un acercamiento de los conectores

del UPS y del paquete de baterías. En seguida, utilice la placa metálica y el perno que recibió para

bloquear los dos conectores tal como se muestra en la parte 3 del dibujo.

Italiano

A. Un solo blocco batteria: Se l’UPS è dotato di un unico blocco batteria, collegare il cavo dal blocco al

Fortress, come viene mostrato nelle parti 1 e 2 dell’illustrazione. La parte 1 mostra il collegamento tra UPS

e il blocco batteria, la parte 2 invece mostra un primo piano dei raccordi provenienti dall’UPS e dal blocco

batteria. A questo punto, per bloccare i due raccordi, usare la piastra metallica e il bullone provvisto, come

mostrato nella parte 3 dell’illustrazione.

Português

A. Um jogo de baterias Se o UPS tiver um jogo de baterias, conecte os cabos do jogo de baterias ao

Fortress, conforme mostrado nas partes 1 e 2 do desenho; a parte 1 mostra a conexão entre o UPS e o

jogo de baterias, e a parte 2 apresenta um imagem ampliada dos conectores do UPS e do jogo de

baterias. Em seguida, use a chapa de metal e o parafuso fornecidos com o equipamento para travar os

dois conectores conforme mostrado na parte 3 do desenho.

Page 11

English

B. Two Battery Packs:

If your LI 1.3K has two battery packs, connect the cables from the bottom battery pack to the Fortress battery connector as shown. Use the metal plate and bolt you received to lock the connection as shown in part A, drawing 3. Next, find the metal plate in the upper right corner of the bottom battery pack; remove the screws in this plate and remove the plate. You should see a battery connector. Connect the battery cables from the top battery pack to the connector on the bottom battery pack. Then, put the plate on the battery pack upside-down as shown, and use the screws you removed to reattach the plate.

Français

B. Deux blocs de batteries :

Si votre LI 1.3 K a deux blocs de batteries, reliez les câbles du bloc de batteries inférieur au connecteur de batterie du Fortress, comme indiqué. Utilisez la plaque métallique et le boulon fournis pour verrouiller la connexion comme indiqué à A, dessin No3. Puis cherchez la plaque métallique située au coin droit supérieur du bloc de batteries inférieur ; retirez les vis de cette plaque et la plaque elle-même. Vous devriez voir un connecteur de batteries. Reliez les câbles de batterie du bloc de batteries supérieur au connecteur qui se trouve sur le bloc de batteries inférieur. Puis mettez la plaque sur le bloc de batteries la tête en bas, comme indiqué, et utilisez les vis que vous avez retirées pour refixer la plaque.

Deutsch

B. Zwei Batterie-Pakete:

Wenn Ihr Modell LI 1.3K zwei Batterie-Pakete hat, schließen Sie die Kabel des unteren Batterie-Pakets wie abgebildet an den Batterieanschluß der Fortress an. Benutzen Sie dann die Metallplatte und die beiliegenden Schrauben, um die Verbindung wie in Teil A, Zeichnung 3, abgebildet festzuziehen. Entfernen Sie dann die beiden Schrauben auf der Metallplatte oben rechts auf dem unteren Batterie-Paket und nehmen Sie die Platte ab. Schließen Sie jetz die Batteriekabel vom oberen Batterie-Paket an den freigelegten Batterieanschluß auf dem unteren Batterie-Paket an. Bringen Sie die Platte wie abgebildet am Batterie-Paket an (d.h. die obere Kante der Platte zeigt jetzt nach unten) und befestigen Sie sie wieder mit den Schrauben.

Español

B. Dos paquetes de baterías:

Si su LI 1.3K tiene dos paquetes de baterías, conecte los cables del paquete de baterías que está abajo al conector de baterías del Fortress. Utilice la placa metálica y el perno que recibió para bloquear la conexión tal como se muestra en la parte A, dibujo 3. En seguida ubique la placa metálica en la esquina superior derecha del paquete de baterías que está abajo; quite los tornillos en esta placa y quite la placa. Debe poder ver un conector de batería. Conecte los cables de la batería del paquete de baterías que está arriba al conector del paquete de baterías que está abajo. Luego coloque la placa, parte superior hacia abajo, en el paquete de baterías, tal como se muestra y utilice los tornillos que quitó para volver a fijar la placa.

Italiano

B. Due blocchi batteria:

Se il LI 1.3K è munito di due blocchi batteria, collegare i cavi, dal blocco batteria di base, al connettore della batteria di Fortress, come mostrato nell’illustrazione. Usare la piastra metallica e il bullone provvisto per bloccare il connettore, come mostrato nella parte A, illustrazione 3. A questo punto, trovare la piastra metallica nell’angolo superiore destro del blocco batteria di base, rimuovere le viti in questa piastra e rimuovere la piastra. Dovreste essere in grado di vedere un connettore di batteria. Collegare i cavi della batteria, dal blocco batteria superiore, al connettore situato sul blocco batteria di base. A questo punto, situare la piastra sul blocco batteria in posizione capovolta, come mostrato nell’illustrazione e, per riattaccare la piastra, usare le viti precedentemente rimosse.

Português

B. Dois jogos de baterias

Se o LI 1.3K tiver dois jogos de baterias, conecte os cabos do jogo de baterias inferior ao conector de bateria Fortress, conforme mostrado. Use a chapa de metal e o parafusofornecidos com o equipamentopara travar a conexão conforme mostrado na parte A, desenho 3. Em seguida, procure a chapa de metal no canto superior direito do jogo de baterias inferior; retire os parafusos desta chapa e em seguida retire a chapa. Você verá o conector de bateria. Conecte os cabos de bateria do jogo de baterias superior ao conector no jogo de baterias inferior. Em seguida, inverte a chapa e coloque a no jogo de baterios, conforme mostrado, e use os parafusos que tiver retirado para reinstalar a chapa.

Page 12

English

C. Three Battery Packs: If your LI 1.3K has three battery packs, follow these steps:

I. See the drawing; connect the cables from battery pack “1” to the UPS battery connector as

shown. Use the metal plate and bolt to lock the connection as shown in part A, drawing 3.

II. Find the metal plate in the upper right corner of battery pack “1”; remove the screws in the

plate and remove the plate. You should see a battery connector. Connect the cables from battery pack “2” to the connector on battery pack “1.” Then, put the plate on the battery pack upside-down as shown and use the screws you removed to reattach it.

III. Repeat step ii. to connect battery pack “3” to battery pack “2.”

Français

C. Trois blocs de batteries : Si votre LI 1.3 K a trois blocs de batteries, suivez ces étapes :

I. Regardez le dessin; reliez les câbles du bloc de batteries “1” au connecteur de batteries de l’UPS, comme

indiqué. Utilisez la plaque métallique et le boulon pour verrouiller la connexion comme indiqué à A, dessin No3.

II. Trouvez la plaque métallique au coin supérieur droit du bloc de batteries “1”; retirez les vis de la plaque et la

plaque elle-même. Vous devriez apercevoir un connecteur de batteries. Reliez les câbles du bloc de batteries “2” au connecteur du bloc de batteries “1”. Puis posez la plaque sur le bloc de batteries la tête en bas comme indiqué et utilisez les vis que vous avez retirées pour refixer la plaque.

III. Répétez l’étape ii. pour relier le bloc de batteries “3” au bloc de batteries “2”.

Deutsch

C. Drei Batterie-Pakete: Wenn Ihr Modell LI 1.3K drei Batterie-Pakete hat, führen Sie folgende Schritte durch:

I. Sehen Sie sich die Zeichnung an und schließen Sie die Kabel von Batterie-Paket „1“ wie abgebildet an den

Batterieanschluß der USV an. Verwenden Sie die Metallplatte und die Schraube, um die Verbindung wie in Teil A, in Zeichnung 3, festzuziehen.

II. Entfernen Sie die Schrauben auf der Metallplatte oben rechts auf Batterie-Paket „1“ und nehmen Sie die

Platte ab. Schließen Sie jetz die Kabel von Batterie-Paket „ 2 “ an den freigelegten Batterieanschluß auf Batterie-Paket „1“ an. Bringen Sie die Platte dann wie abgebildet am Batterie-Paket an (d.h. die obere Kante der Platte zeigt jetzt nach unten) und befestigen Sie sie wieder mit den Schrauben.

III. Wiederholen Sie Schritt ii., um Batterie-Paket „3“ an Batterie-Paket „2“ anzuschließen.

Español

C. Tres paquetes de baterías: Si su LI 1.3K tiene tres paquetes de baterías, siga estos pasos:

I. Vea el dibujo; conecte los cables del paquete de baterías “1” al conector de baterías del UPS. Utilice la placa

metálica y el perno que recibió para bloquear la conexión tal como se muestra en la parte A, dibujo 3.

II. Ubique la placa metálica en la esquina superior derecha del paquete de baterías “1”; quite los tornillos en

esta placa y quite la placa. Debe poder ver un conector de batería. Conecte los cables del paquete de baterías “2” al conector que se encuentra en el paquete de baterías “1”. Luego coloque la placa, parte superior hacia abajo, en el paquete de baterías, tal como se muestra y utilice los tornillos que quitó para volver a fijar la placa.

III. Repita el paso ii. para conectar el paquete de baterías “3” al paquete de baterías “2”.

Italiano

C. Tre blocchi batteria: Se il LI 1.3K è munito di tre blocchi batteria, effettuare le seguenti operazioni:

I. Osservare l’illustrazione. Collegare i cavi dal blocco batteria “1” al connettore della batteria di UPS, come

mostrato nell’illustrazione. Per bloccare il connettore, usare la piastra metallica e il bullone come viene mostrato nella parte A, illustrazione 3.

II. Trovare la piastra metallica nell’angolo superiore destro del blocco batteria “1”, rimuovere le viti nella piastra e

rimuovere la piastra. Dovreste riuscire a vedere un connettore delle batterie. Collegare i cavi dal blocco batteria “2” al connettore sul blocco batteria “1”. A questo punto, situare la piastra sul blocco batteria in posizione capovolta, come mostrato nell’illustrazione, e usare le viti precedentemente rimosse per riattaccarla.

III. Ripetere le operazioni riportate al punto ii. per collegare il blocco batteria “3” al blocco batteria “2”.

Português

C. Três jogos de baterias Se o LI 1.3K tiver três jogos de baterias, siga as seguintes etapas:

a.Observe o desenho; conecte os cabos do jogo de bateria “1” ao conector de bateria do UPS, conforme

mostrado. Use a chapa de metal e o parafuso fornecidos com o equipamento para travar a conexão conforme mostrado na parte A, desenho 3.

b.Procure a chapa de metal no canto superior direito do jogo de baterias “1”, retire o parafuso da chapa e retire a

chapa. Você verá um conector de bateria. Conecte os cabos do jogo de baterias “2” ao conector no jogo de baterias “1”. Em seguida, inverta a chapa e coloque a no jogo de baterias, conforme mostrado e use os parafusos que tiver retirado para reinstalar a chapa.

c.Repita a etapa “b” para conectar o jogo de baterias “3” o jogo de baterias “2”.

Page 13

English

Starting all Fortress Models: Steps 9-22

Make sure the UPS is near the equipment it will protect. Leave at least 3 inches (80 mm) space for ventilation on each side of the UPS and behind the UPS, and do not put the UPS near a source of heat.

Français

Mise en marche de tous les modèles de Fortress : étapes 9-22

Assurez-vous que l’UPS se trouve à proximité de l’équipement à protéger. Laissez un espace d’au moins 80 mm pour la ventilation de chaque côté de l’UPS, et derrière ce dernier, et ne le posez pas près d’une source de chaleur.

Deutsch

Inbetriebnahme der Fortress (alle Modelle): Schritt 9-22

Vergewissern Sie sich, daß die USV in der Nähe der Geräte steht, die sie schützen soll. Lassen Sie auf beiden Seiten und hinter der USV zur Lüftung einen Freiraum von mindestens 80 mm, und stellen Sie die USV nicht in der Nähe einer Wärmequelle auf.

Español

Para poner en marcha cualquiera de los modelos Fortress: Pasos 9-22

Asegúrese que el UPS esté cerca del equipo que va a proteger. Deje por lo menos 3 pulgadas (80 mm) de espacio libre para ventilación a cada lado del UPS y atrás del UPS y no coloque el UPS cerca de una fuente de calor.

Italiano

Avvio di tutti i modelli Fortress: Operazioni 9-22

Accertarsi che l’UPS sia vicino al sistema da proteggere. Lasciare almeno 80 mm di spazio per la ventilazione su ciascun lato dell’UPS e dietro l’UPS. Non collocare l’UPS vicino ad una fonte di calore.

Português

Início de funcionamento de todos os modelos Fortress: etapas 9 a 22

Certifique-se de que o UPS está próximo ao equipamento que irá proteger. Deixe um espaço de pelo menos 80 mm de cada lado do UPS e atrás do mesmo, e não coloque o UPS próximo a nenhuma fonte de calor.

Page 14

English

Français

Deutsch

Español

Italiano

Português

You will find the label shown below inserted in this manual. Write your UPS service representative’s telephone number and/or e-mail address on the label. (See the Customer Process for Service on pages 29-

30.)Then, attach the label to your unit or place it near your unit. DO NOT PLACE THE LABEL OVER

THE UPS’ VENTILATION HOLES. If your UPS needs service or if you have UPS questions, this label will provide the contact information you need.

For 9910 UPS Service, contact:

________________________________________

(Phone Number)

_________________________________________

(email address)

L’étiquette illustrée ci-dessous a été glissée dans ce manuel. Inscrivez à cet endroit le numéro de téléphone de votre agent de réparation et/ou son adresse E-mail (pour la Procédure à suivre en cas de

réparation, reportez-vous aux pages 29-30). Attachez ensuite cette étiquette sur votre appareil ou à

proximité. NE PLACEZ PAS L’ETIQUETTE SUR LES BOUCHES DE VENTILATION DE L’APPAREIL.Si une réparation s’avère nécessaire ou en cas de question, cette étiquette vous fournira immédiatement les informations dont vous aurez besoin.

“For 9910 UPS Service, contact:” = Pour une réparation du modèle 9910, composez le “Phone Number” = Numéro de téléphone “email address” = Adresse E-Mail

Der unten abgebildete Aufkleber liegt diesem Handbuch bei. Tragen Sie die Telefonnummer und/oder E-mail-Adresse Ihres Kundendienstvertreters auf dem Aufkleber ein (siehe Abschnitt Kundendienst auf

den Seiten 29-30). Bringen Sie dann diesen Aufkleber an oder in der Nähe des Gerätes an. DER

AUFKLEBER DARF NICHT AUF DIE LÜFTUNGSSCHLITZE DES USV GEKLEBT WERDEN. Wenn Sie Fragen zu Ihrem USV haben oder eine Reparatur erforderlich ist, finden Sie die nötigen Kontaktinformationen auf diesem Aufkleber.

“For 9910 UPS Service, contact” = 9910 Kundendienst “Phone Number” = Telefonnummer “email address” = E-Mail-Adresse

Encontrará la etiqueta que aparece a continuación insertada dentro de este manual. Anote en la etiqueta el número de teléfono y la dirección de correo electrónico de su representante de servicio para el UPS (vea el Procedimiento de Servicio al Cliente, en las páginas 29-30). Luego fije la etiqueta en la unidad misma o en sus inmediaciones. NO COLOQUE LA ETIQUETA SOBRE LOS ORIFICIOS DE VENTILACION DEL UPS. Si el UPS necesita servicio, o si usted tiene alguna consulta, en esta etiqueta encontrará la información pertinente.

“For 9910 UPS Service, contact” = Contacto de servicio para el UPS 9910 “Phone Number” = Número de teléfono “email address” = Dirección de correo electrónico

Troverete l’etichetta sottoindicata inserita nel manuale. Scrivete sull’etichetta il numero di telefono del rappresentante del servizio manutenzione UPS e/o il suo indirizzo di posta elettronica (vedi Procedura

per richiedere l’assistenza tecnica, alle pagine 29-30). Incollate quindi l’etichetta sulla vostra unità o

sistematela vicino ad essa. NON METTETE L’ETICHETTA SOPRA I FORI DI VENTILAZIONE DELL’UPS. Se il vostro UPS ha bisogno di manutenzione/riparazione, oppure se avete dei quesiti riguardanti l’UPS, su questa etichetta troverete le informazioni necessarie su come accedere al servizio assistenza tecnica.

“For 9910 UPS Service, contact:” = Per il servizio UPS 9910, contattare “Phone Number” = Numero di telefono “email address” = Indirizzo di posta elettronica

Você encontrará a etiqueta apresentada a seguir inserida neste manual. Escreva na etiqueta o número de telefone de seu representante de serviço da UPS e/ou o endereço de correio eletrônico. (Veja o

Processo do Cliente para Serviço nas páginas 29-30.)Em seguida, fixe a etiqueta no equipamento ou

coloque-a perto do equipamento. NÃO COLOQUE A ETIQUETA SOBRE OS ORIFÍCIOS DE VENTILAÇÃO DA UPS. Se a sua UPS precisar de manutenção ou se você tiver dúvidas sobre a UPS, esta etiqueta fornecerá as informações de contato que você precisa.

“For 9910 UPS Service, contact” = Para o Serviço de UPS 9910, entre em contato com “Phone Number” = Número de telefone “email address” = Endereço de correio eletrônico

Page 15

English

Before you start the UPS, plug the power cord you received with the AS/400 into the UPS as shown. (Do not use the cord that came with the UPS.)

For some 1.3K models with extended battery time, you must plug the AS/400 power cord into a cord attached to the UPS instead of plugging it into the UPS itself.

Français

Avant de mettre l’UPS en marche, branchez le cordon d’alimentation fourni avec l’AS/400 dans l’UPS, comme indiqué. (N’utilisez pas le cordon fourni avec l’UPS.)

Pour certains modèles 1.3 K avec autonomie sur batteries allongée, le cordon d’alimentation de l’AS/400 doit être branché dans un cordon relié à l’UPS au lieu d’être branché dans l’UPS lui-même.

Deutsch

Bevor Sie die USV einschalten, stecken Sie das Kabel, das der AS/400 beiliegt, wie abgebildet in die USV (verwenden Sie nicht das Kabel, das mit der USV geliefert wurde).

Bei einigen 1.3K Modellen mit verlängerter Batteriebetriebszeit wird entfällt das Netzkabel des AS/400 nicht direkt an die USV angeschlossen sondern an ein Adapterkabel.

Español

Antes de encender el UPS, enchufe el cordón eléctrico que recibió con el AS/400 en el UPS tal como se muestra. (No use el cordón que venía con el UPS.)

Para algunos modelos 1.3K con tiempo extendido de baterías, tiene que enchufar el cordón eléctrico del AS/400 a un cordón eléctrico que está conectado al UPS, en vez de enchufarlo al UPS directamente.

Italiano

Prima di avviare l’UPS, inserire nell’UPS il cavo di alimentazione ricevuto con l’AS/400, come indicato nell’illustrazione (non usare il cavo ricevuto con l’UPS).

Per alcuni modelli 1.3K, con tempo di durata della batteria esteso, è necessario inserire il cavo di alimentazione ad un altro cavo attaccato all’UPS, invece di inserirlo direttamente nell’UPS.

Português

Antes de colocar o UPS em funcionamento, conecte no UPS o cabo de alimentação que acompanha o AS/400, conforme mostrado. (Não use o cabo de alimentação fornecido com o UPS).

Para alguns modelos 1.3K com bateria de carga prolongada, deve-se conectar o cabo de alimentação do AS/400 ao cabo interligado ao UPS, em vez de conectá-lo ao próprio UPS.

Page 16

English

Next, plug the cord into the wall outlet.* *If the plug does not fit your outlet, call an electrician to install the correct outlet.

Français

Puis branchez le cordon dans la prise murale.* *Si la fiche ne s’adapte pas à votre prise, demandez à un électricien d’installer une prise convenable.

Deutsch

Schließen Sie das Netzkabel jetzt ans Netz an.* *Wenn der Stecker nicht in die Steckdose paßt, lassen Sie die richtige Steckdose von einem Elektriker installieren.

Español

A continuación, enchufe el cordón en el tomacorriente de pared.* *Si el enchufe no cabe en el tomacorriente, llame a un electricista para que instale el tomacorriente correcto.

Italiano

Inserire il cavo nella presa di corrente a muro.* *Se la spina non entra nella presa di corrente, chiamare un elettricista e fargli installare una presa adatta.

Português

En seguida, conecte o cabo de alimentação em uma tomada de parede.* *Se o plugue não se encaixar na tomada, contate um eletricista para que o mesmo instale a tomada certa.

Page 17

English

Now, turn the UPS On/Off (I/O) switch to On (I). The UPS will test its front panel lights, display, and battery charge.

Français

Maintenant, mettez le commutateur de Marche/Arrêt (I/O) sur Marche (I). L’UPS va tester les témoins du panneau avant, l’affichage et la charge de la batterie.

Deutsch

Stellen Sie den Ein/Aus-Schalter (I/O) der USV auf Ein (I). Die USV testet die Anzeigelampen und die Digitalanzeige auf der Bedienerkonsole sowie die Batterieladung.

Español

Ahora, mueva el interruptor Encendido/Apagado (I/O) del UPS a la posición de Encendido (I). El UPS probará las luces del panel frontal, la pantalla y el nivel de carga de la batería.

Italiano

Mettere l’interruttore Acceso/Spento (I/O) dell’UPS nella posizione di acceso (I). L’UPS verificherà le luci spia del pannello frontale e lo stato di carica della batteria.

Português

Em seguida, coloque o interruptor do UPS On/Off (I/O) na posição On (Ligado) (I). O UPS testará as luzes e o display no painel frontal e a carga da bateria.

CAUTION:

The UPS outlets now have power.

Attention :

les prises de l’UPS sont maintenant alimentées.

Vorsicht:

Die USV-Steckdosen stehen jetzt unter Spannung.

Precaución:

Ahora los tomacorrientes del UPS tienen energía eléctrica.

Attenzione:

Le prese dell’UPS sono adesso sotto tensione.

Atenção:

As tomadas do UPS agora contém energia.

Page 18

English

After this startup test, the display will show “PASS,” then the model number, and the green Line light will come on, showing that the UPS is running normally. The red and yellow lights will be off. If this happens, skip to step 16. If not, go on to step 15.

Français

Après ce test de mise en marche, l’affichage va indiquer “PASS”, puis le numéro de modèle et le témoin vert Line s’illuminera, indiquant que l’UPS fonctionne normalement. Le témoin rouge et le témoin jaune sont éteints. Dans ce cas, passez à l’étape 16. Sinon, passez à l’étape 15.

Deutsch

Nach diesem Selbsttest beim Einschalten erscheint auf der Anzeige “PASS”, gefolgt von der Modellnummer, Das anschließende Aufleuchten, der grünen Netzanzeige bestätigt, daß die USV normal läuft. Die rote und die gelbe Anzeigelampe leuchten nicht auf. Wenn dies eintritt, gehen Sie bitte zu Schritt 16. Wenn nicht, machen Sie mit Schritt 15 weiter.

Español

Después de esta prueba de arranque, en la pantalla aparecerá el mensaje “PASS”, seguido del número de modelo y luego la luz verde de Línea se iluminará para indicar que el UPS está funcionando normalmente. Las luces roja y amarilla permanecerán apagadas. Si esto sucede, refiérase al paso 16. De lo contrario siga las instrucciones del paso 15.

Italiano

Terminata verifica di accensione, il display visualizzerà “PASS”, il numero di modello e si accenderà la luce spia verde Line, indicante che l’UPS funziona regolarmente. Le luci spia rossa e gialla saranno spente. Se è così, passare al punto 16, altrimenti procedere al punto 15.

Português

Após este teste inicial, o display indicará “PASS” o número do modelo, e a luz verde de Line acenderá, indicando que o UPS está funcionando normalmente. As luzes vermelha e amarela apagarão. Caso isto ocorra, passe para a etapa 16. Caso contrário, passe para a etapa 15.

Page 19

English

If the red Alarm light is on after the startup test, go to the “Alarms” section in the Fortress Guide (or Fortress Manual). If there is another problem, go to the “Troubleshooting” section in the Fortress Guide (or Fortress Manual).

Français

Si le témoin rouge Alarm demeure illuminé après le test de mise en marche, passez à la section “Alarms” (Alarmes) du Guide du Fortress (ou du Manuel du Fortress). Si un autre problème se présente, passez à la section “Dépannage” du Guide du Fortress (ou du Manuel du Fortress).

Deutsch

Wenn die rote Alarmanzeige nach dem Inbetriebnahmetest aufleuchtet, schlagen Sie den Abschnitt „Alarme“ in der Fortress-Anleitung (bzw. im Fortress-Handbuch) auf. Wenn ein anderes Problem besteht, schlagen Sie unter „Fehlersuche“ in der Fortress-Anleitung (bzw. im Fortress-Handbuch) nach.

Español

Si la luz roja de Alarm (Alarma) está encendida después de la prueba de arranque, pase a la sección de Alarmas en la Guía del Fortress (o Manual del Fortress). Si existe otro problema pase a la sección de “Resolución de problemas” en la Guía del Fortress (o Manual del Fortress).

Italiano

Se, dopo la verifica di accensione, la spia rossa è accesa, consultare la sezione “Alarms” (Allarmi) della “Fortress Guide” (Guida a Fortress) o del “Fortress Manual” (Manuale di Fortress). Se vi sono altri problemi, consultare la sezione “Troubleshooting” (Localizzazione dei guasti) della “Fortress Guide” (Guida a Fortress) o del “Fortress Manual” (Manuale di Fortress).

Português

Se a luz vermelha do Alarme ficar acesa após o teste inicial, passe para a seção “Alarme” do Guia Fortress (ou Manual Fortress). Se houver outro problema, passe para a seção “Diagnóstico” do Guia Fortress (ou Manual Fortress).

Page 20

English

The battery charges automatically whenever the green Line light is on. To make sure the UPS’ battery can

supply power, let the battery charge overnight, especially if you have

stored

the UPS. You can continue with step 17 before the UPS finishes charging the batteries, but if there is a power outage, the UPS may provide less battery time until the batteries are charged. If you need to change the UPS inverter output voltage, see the section in this guide called “Changing the Fortress’ Inverter Voltage.” This section also explains under what conditions you might want to change the voltage.

Français

La batterie se recharge automatiquement lorsque le témoin vert est illuminé. Pour avoir la certitude que la

batterie de l’UPS peut fournir de l’alimentation, laissez-la charger pendant une nuit, surtout si vous avez

entreposé

l’UPS pendant un certain temps. Vous pouvez passer à l’étape 17 avant que l’UPS ne finisse de recharger les batteries, mais s’il se produit une panne de courant, l’UPS fournira peut-être une autonomie sur batteries plus courte jusqu’à ce que les batteries soient rechargées. Si vous avez à changer la tension de sortie du convertisseur de l’UPS, référez-vous dans le présent guide à la section intitulée “Changing the Fortress’ Inverter Voltage” (Changement de la tension du convertisseur du Fortress). Cette section explique également dans quelles conditions vous pourriez désirer modifier la tension.

Deutsch

Wenn die grüne Netzanzeige aufleuchtet, wird die Batterie automatisch aufgeladen. Um sicherzustellen,

daß die Batterie der USV Strom liefern kann, laden Sie die Batterie über Nacht auf. Dies ist besonders wichtig, wenn die USV zuvor

gelagert

wurde. Sie können mit Schritt 17 weitermachen bevor die USV ihre Batterien vollständig aufgeladen hat, aber falls ein Stromausfall eintritt, liefert die USV unter Umständen weniger Batteriebetriebszeit, wenn die Batterien noch nicht vollständig aufgeladen sind. Wenn Sie die Ausgangsspannung des Wechselrichters der USV ändern müssen, schlagen Sie bitte den Teil „Changing the Fortress’ Inverter Voltage“ (Wie Sie die Wechselrichterspannung der Fortress ändern) in dieser Anleitung auf. In diesem Teil wird außerdem erklärt, unter welchen Umständen die Spannung eventuell geändert werden sollte.

Español

La batería se carga automáticamente siempre que la luz verde de Línea esté encendida. Para estar seguro

que la batería del UPS puede suministrar energía, déjela cargando toda la noche, especialmente si ha

almacenado

el UPS. Puede continuar con el paso 17 antes de que el UPS cargue completamente las baterías, pero si hay un corte de energía eléctrica, puede ser que el UPS proporcione menos tiempo de batería hasta que las baterías estén cargadas. Si necesita cambiar el voltaje de salida del inversor del UPS vea la sección de esta guía titulada “Changing the Fortress’ Inverter Voltage”. Esta sección también explica bajo qué condiciones usted querrá cambiar el voltaje.

Italiano

Le batterie si caricano automaticamente quando la spia verde “Line” (linea) è accesa. Per assicurarsi che le batterie dell’UPS forniscano l’alimentazione, sarà necessario lasciarle caricare per tutta la notte, in particolare se l’UPS è stato

riposto in magazzino

. Potete continuare ad effettuare le operazioni descritte al punto 17, prima che l’UPS abbia finito di caricare le batterie, ma, nel caso in cui si verifichi una mancanza di tensione, l’UPS potrebbe fornire minore tempo di durata delle batterie, finché le batterie vengono caricate. Per cambiare la tensione di uscita dell’invertitore dell’UPS, consultare la sezione di questa guida intitolata “Changing the Fortress’ Inverter Voltage.”

Português

As baterias carregam-se automaticamente toda vez que a luz verde de Linha estiver ligada. Para

assegurar que as baterias do UPS têm condições de fornecer energia, deixe que as baterias carreguem durante a noite, especialmente se tiver

armazenado

o UPS. Pode-se continuar com a etapa 17 antes que o UPS acabe de carregar as baterias. Mas, se houver uma queda de energia, o UPS poderá reduzir o tempo de fornecimente de bateria até que as baterias estejam carregadas. Se precisar mudar a voltagem de saída do inversor do UPS, consulte a seção deste guia chamada “Changing the Fortress’ Inverter Voltage” (Mudança da voltagem do inversor Fortress). Esta seção também explica sob que condições você deverá mudar a voltagem.

Page 21

English

Turn off the equipment you want to protect. Use the power cord or power jumper cord you received with the UPS to connect the AS/400 to the UPS. You can plug other equipment directly into the UPS if it does not overload the UPS; if you overload the UPS, it will sound an alarm.

Français

Mettez hors tension l’équipement que vous désirez protéger. Utilisez le cordon d’alimentation ou le cordon d’alimentation bretelle reçu avec l’UPS pour relier l’AS/400 à l’UPS. D’autres unités d’équipement peuvent être branchées directement dans l’UPS à condition de ne pas surcharger ce dernier ; si vous surchargez l’UPS, une sonnerie d’alarme se fera entendre.

Deutsch

Schalten Sie die Geräte, die Sie schützen wollen, aus. Schließen Sie die AS/400 mit dem Netzkabel oder dem Verbindungskabel, daß zum Lieferumfang gehört, an die USV an. Sie können andere Geräte direkt an die USV anschließen entfällt, solange die USV hierdurch nicht überlastet wird; falls die USV überlastet wird, ertönt ein Alarm.

Español

Apague el equipo que desea proteger. Use el cordón eléctrico o el cordón eléctrico de acoplamiento que recibió con el UPS para conectar el AS/400 al UPS. Puede enchufar otro equipo directamente en el UPS si esto no sobrecarga el UPS; si sobrecarga el UPS, sonará una alarma.

Italiano

Spegnere l’unità che si desidera proteggere. Per collegare l’AS/400 all’UPS, usare il cavo di alimentazione o il cavo di alimentazione di accoppiamento ricevuto con l’UPS . E’ possibile inserire altre unità direttamente all’UPS, purché esse non sovraccarichino l’UPS stesso. Sel’UPS viene sovraccaricato, suonerà un allarme.

Português

Desligue o equipamento que deseja proteger. Use o cabo de alimentação ou o cabo-ponte fornecido com o UPS para conectar o AS/400 ao UPS. Pode-se conectar outros equipamentos diretamente ao UPS se isto não sobrecarregá-lo; caso hoja uma sobrecarga, o UPS, emitirá um alarme.

Page 22

English

Plug the end of the logic interface cable labeled “UPS” into the communication connector on the UPS. Plug the end of the cable labeled “AS/400” into the connector labeled “UPS” on the AS/400. This connector is on the back of the AS/400 base cabinet. If you reverse the cable, the AS/400 will power

down immediately.

Français

Branchez l’extrémité du câble d’interface logique marquée “UPS” dans le connecteur de communication de l’UPS. Branchez l’autre extrémité du câble marquée “AS/400” dans le connecteur marqué “UPS” sur l’AS/400. Ce connecteur se trouve à l’arrière du module de base de l’AS/400. Si vous inversez le

câble, le AS/400 se met immédiatement hors tension.

Deutsch

Stecken Sie das Ende des Schnittstellenkabels mit der Aufschrift „UPS“ in den Kommunikationsanschluß der USV. Stecken Sie das Ende des Kabels mit der Aufschrift „AS/400“ in den Anschluß mit der Aufschrift „UPS“. Dieser Anschluß befindet sich auf der Rückseite des AS/400Gehäuses. Falls Sie die Kabel verkehrt herum anschließen, schaltet sich der AS/400 sofort aus.

Español

Enchufe el extremo del cable del interface lógico marcado “UPS” en el conector de comunicaciones del UPS. Enchufe el otro extremo del cable marcado “AS/400” en el conector marcado “UPS” en el AS/400. Este conector se encuentra en la parte posterior del gabinete del AS/400. Si invierte el cable, el

AS/400 se apagará inmediatamente.

Italiano

Inserire l’estremità del cavo d’interfaccia logica, contrassegnato “UPS”, nel connettore per le comunicazioni sull’UPS. Inserire l’estremità del cavo, contrassegnato “AS/400”, nel connettore contrassegnato “UPS” sull’AS/400. Questo connettore si trova dietro l’AS/400 di base. Se il cavo viene

invertito, l’AS/400 si spegnerà immediatamente.

Português

Conecte a extremidade do cabo de interface lógica identificado como “UPS” no conector de comunicação do UPS. Conecte a extremidade do cabo identificado como “AS/400” no conector “UPS” do AS/400. Este conector se encontra na parte posterior do gabinete do AS/400. Se o cabo for

instalado ao contrário, o AS/400 desligar-se-á imediatamente.

"AS/400"

"UPS"

Page 23

English

If this is the first time you have installed your AS/400, skip to step 20. Otherwise, switch on the equipment plugged into the UPS; turn on one piece of equipment at a time.

Français

Si vous procédez à l’installation initiale de votre AS/400, passez directement à l’étape 20. Autrement, mettez sous tension les unités d’équipement branchées dans l’UPS, une par une.

Deutsch

Wenn Sie Ihre AS/400 zum ersten Mal installieren, machen Sie mit Schritt 20 weiter. Wenn nicht, schalten Sie die an die USV angeschlossenen Geräte nacheinander ein.

Español

Si ésta es la primera vez que usted instala su AS/400, continúe en el paso 20, de lo contrario, encienda el equipo enchufado al UPS; encienda cada parte del equipo por separado.

Italiano

Se questa è la prima volta che avete installato l’AS/400, fate riferimento direttamento all’operazione 20, altrimenti accendete pure le unità collegate all’UPS. Accendere un’unità alla volta.

Português

Se esta é a primeira vez que instalado o AS/400 está sendo, passe para a etapa 20. Do contrário, ligue o equipamento conectado ao UPS; ligue um equipamento de cada vez.

Page 24

English

Now, look at the three lights on the UPS front panel. The red Alarm light means there is a problem — see the “Alarms” section in the Fortress Guide (or Fortress Manual). A constant yellow Battery light means the UPS is providing battery power — see the Fortress Guide (or Fortress Manual). The green

Line light shows the UPS is protecting your equipment while it uses power from the wall outlet.

Français

Maintenant, regardez les trois témoins du panneau avant de l’UPS. Le témoin rouge Alarm signale l’existence d’un problème - référez-vous à la section “Alarmes” du Guide du Fortress (ou du Manuel du Fortress). Quand le témoin jaune Battery demeure illuminé, cela signifie que l’UPS fournit du courant batterie - référez-vous au Guide du Fortress (ou au Manuel du Fortress). Le témoin vert Line indique que l’UPS protège votre équipement en utilisant l’alimentation électrique en provenance de la prise murale.

Deutsch

Sehen Sie sich jetzt die drei Anzeigelampen auf der Bedienerkonsole der USV an. Die rote Alarmanzeige zeigt an, daß ein Problem besteht — schlagen Sie den Abschnitt „Alarme“ in der Fortress-Anleitung (bzw. im Fortress-Handbuch) auf. Eine ständig aufleuchtende gelbe Batterieanzeige bedeutet, daß die USV Batteriestrom liefert — schlagen Sie die Fortress-Anleitung (bzw. das FortressHandbuch) auf. Die grüne Netzanzeige (Line) zeigt an, daß die USV Ihre Geräte schützt, während sie vom Netz gespeist wird.

Español

Ahora observe las tres luces en el panel frontal del UPS. La luz roja de Alarm indica que hay un problema - vea la sección de “Alarmas” en la Guía del Fortress (o Manual del Fortress). La luz amarilla constante de Battery indica que el UPS está alimentando energía de las baterías - vea la Guía del Fortress (o Manual del Fortress). La luz verde de Line indica que el UPS está protegiendo su equipo mientras usa energía comercial del tomacorrientes de la pared.

Italiano

Osservare adesso le tre spie sul pannello frontale dell’UPS. La spia rossa “Alarm” indica che esiste un problema: in questo caso, consultare la sezione “Allarmi” della “Fortress Guide” (Guida a Fortress) o del “Fortress Manual” (Manuale di Fortress). Una spia gialla fissa “batteria” significa che l’UPS sta fornendo l’alimentazione dalla batteria: in questo caso, consultare la “Fortress Guide” (Guida a Fortress) o il “Fortress Manual” (Manuale di Fortress). La spia verde “linea” indica che l’UPS sta proteggendo l’unità usando l’alimentazione mediante la presa di corrente a muro.

Português

Em seguida, observe as três luzes do painel frontal do UPS. A luz vermelha de Alarme indica a existência de problema — consulte a seção “Alarme” contida no Guia Fortress (ou Manual Fortress). A luz amarela de Bateria acesa constantemente significa que o UPS está fornecendo energia a partir da bateria — consulte o Guia Fortress (ou Manual Fortress). A luz verde de Linha indica que o UPS está protegendo o equipamento usando energia da tomada.

Page 25

English

Please fill out the $25,000 Double Lifetime Warranty Registration card and return it to Best Power. To learn more about the UPS front panel lights and keys, please see the section in the Fortress Guide

(or Fortress Manual) called “Understanding the Fortress Front Panel.”

Français

Veuillez remplir la carte d’enregistrement de garantie double à vie de 25 000 Dollars et la retourner à Best Power.

Pour de plus amples renseignements sur les témoins lumineux et les touches du panneau avant de l’UPS, référez-vous à la section intitulée “Explication du panneau avant de Fortress” dans le Guide du Fortress (ou dans le Manuel du Fortress).

Deutsch

Füllen Sie bitte die Registerkarte für die doppelte Garantie auf Lebenszeit über $ 25.000 aus und schicken Sie sie an Best Power zurück.

Schlagen Sie jetzt bitte den Abschnitt „Die Bedienerkonsole der Fortress“ in der Fortress-Anleitung (bzw. im Fortress-Handbuch) auf, um sich mit den Anzeigelampen und Tasten auf der Bedienerkonsole der USV vertraut zu machen.

Español

Sírvase llenar la tarjeta de registro de garantía doble de duración del producto de $25,000 y envíela a Best Power.

Para aprender más sobre las luces y teclas del panel frontal del UPS, por favor vea la sección titulada Panel Frontal del Fortress en la Guía del Fortress (o Manual del Fortress).

Italiano

Compilare il tagliando di registrazione della garanzia Double Lifetime di $25.000 e spedirlo alla Best Power.

Per saperne di più sulle spie del pannello frontale e sui tasti dell’UPS, consultare la sezione chiamata “Understanding the Fortress Front Panel” (Conoscere il pannello frontale di Fortress), contenuta nella “Fortress Guide” (Guida a Fortress) o nel “Fortress Manual” (Manuale di Fortress).

Português

Preencha a ficha de registro da Garantia Permanente Dupla no valor de $ 25.000 (EUA) e envie a mesma à Best Power.

Para obter mais informações sobre as luzes e interruptores do painel frontal do UPS, favor consultar a seção designada “Entendendo o Painel Frontal do Fortress” contida no Guia Fortress (ou Manual Fortress).

Page 26

English

Français

Deutsch

Español

Italiano

If this is the first time you have installed your AS/400, continue with your AS/400 System Installation Instructions. Make sure you have set the AS/400 QUPSDLYTIM; see page 31.

Si vous procédez à l’installation initiale de votre AS/400, continuez à suivre les instructions d’installation de votre système AS/400. Assurez-vous que vous avez réglé le QUPSDLYTIM de l’AS/400 ; voir la

page 31.

Wenn Sie Ihre AS/400 zum ersten Mal installieren, machen Sie bitte mit der Installationsanleitung für Ihr AS/400-System weiter. Vergewissern Sie sich, daß Sie QUPSDLYTIM des AS/400 wie auf Seite 31 beschrieben eingestellt haben.

Si ésta es la primera vez que instala su AS/400, continúe con las Instrucciones de Instalación del Sistema AS/400. Asegúrese de haber ajustado el QUPSDLYTIM del AS/400; vea la página 31.

Se questa è la prima volta che avete installato l’AS/400, continuate a seguire le istruzioni riguardanti l’installazione del sistema AS/400. Accertatevi di aver predisposto l’AS/400 QUPSDLYTIM. Fare riferimento a pagina 31.

Português

Se esta é a primeira que instalado o AS/400 está sendo, continue com as Instruções de Instalação do Sistema AS/400. Certifique-se de ter preparado o AS/400 QUPSDLYTIM (ver página 31).

Page 27

English

Français

Deutsch

Español

Italiano

Português

CAUTION!

Whenever the UPS “On/Off” switch is on, there may be dangerous voltage present at the UPS outlets. This is true because the UPS battery supplies power even if the UPS is not plugged into the wall outlet.

AVERTISSEMENT!

Des tensions dangereuses peuvent être présentes aux sorties de l’UPS lorsque l’interrupteur de Marche/Arrêt de l’UPS est sur Marche. En effet, la batterie alimente l’UPS même lorsqu’il n’est pas branché dans la prise murale.

WARNUNG

Wenn der “Ein/Aus”-Schalter der USV “eingeschaltet” ist, kann an den Steckdosen der USV gefährliche Spannung anliegen. Die Batterie der USV liefert selbst dann Strom, wenn die USV nicht ans Netz angeschlossen ist.

¡ADVERTENCIA!

Siempre que el interruptor “Encendido/Apagado” esté en la posición “Encendido”, puede haber tensión peligrosa en los tomacorrientes del UPS. Esto se debe a que la batería del UPS sigue suministrando energía aunque el UPS no esté enchufado a un tomacorriente en la pared.

AVVERTENZA

Ogni volta che linterruttore Acceso/Spento dellUPS è nella posizione di Acceso, nelle prese dellUPS può esservi tensione peri-colosa. Questo perché la batteria dell’UPS fornisce alimentazione anche se l’UPS non è collegato alla presa di corrente a muro.

AVISO

Quando o interruptor “On/Off” do UPS estiver na posição On (ligado), poderá haver voltagem perigosa nas tomadas do UPS. Isto ocorre porque a bateria do UPS fornece energia mesmo quando o UPS não está conectado na tomada.

Page 28

AS/400 9401, 9402/9404 UPS IBM Service Support

Limited Two-Year Warranty

The warranty service on the Best Power LI 660, LI 675, LI 750, and LI 1.3K UPS is element exchange. If the UPS becomes inoperative, the entire unit will be replaced. The process for obtaining a replacement unit varies by country. Under no conditions are IBM Customer Engineers authorized to remove the covers. The UPS’s for this program are warranted by Best Power for two years in EMEA. Warranty starts when the UPS is delivered to the customer. See the Best Power Limited Warranty as referenced on page 30 of the Fortress Guide (MLS-

0380) or on page 67 of the Fortress Manual (IMS-0401) for details. Products covered under this limited two-year warranty are:

Limited Five-Year Warranty

The warranty service on the Best Power LI 660, LI 675, LI 750, and LI 1.3K UPS is element exchange. If the UPS becomes inoperative, the entire unit will be replaced. The process for obtaining a replacement unit varies by country. Under no conditions are IBM Customer Engineers authorized to remove the covers. The UPS’s for this program are warranted by Best Power for Five years in the US, Canada, AP, and LAD. Warranty starts when the UPS is delivered to the customer. See the Best Power Limited Warranty as referenced on page 30 of the Fortress Guide (MLS-0380) or on page 67 of the Fortress Manual (IMS-0401) for details. Products covered under this Limited Five-year warranty are:

Model IBM Part Number Best Power Part Number Coverage Area

B08 85F8801 LI660BW EMEA B09 85F8802 LI660DW EMEA B13 85F8806 LI1.3KBW EMEA B14 85F8807 LI1.3KDW EMEA B63 44H3967 LI 675BWM EMEA B64 44H3968 LI 675DWM EMEA B67 44H3969 LI750BWM EMEA B68 44H3970 LI750DWM EMEA B69 44H3971 LI1.3KBWN EMEA B70 44H3972 LI1.3KDWN EMEA

US, Canada, AP, LADLI1.3KDWN44H3972B70

US, Canada, AP, LADLI1.3KBWN44H3971B69

US, Canada, AP, LADLI750DWM44H3970B68

US, Canada, AP, LADLI750BWM44H3969B67

US, Canada, AP, LADLI675DWM44H3968B64

US, Canada, AP, LADLI675BWM44H3967B63

US, Canada, AP, LADLI660DW521H1786B26

US, Canada, AP, LADLI660EW521H1788B28

US, Canada, AP, LADLI660BW521H1787B24

Coverage AreaBest Power Part NumberIBM Part NumberModel

Page 29

Connected Equipment Limited Warranty

Under the “Limited Double Lifetime Warranty,” Best Power offers up to a $25,000 equipment warranty against damage to connected equipment. In order for this warranty to be in effect, the registration card that was included in the original shipping materials must be returned to Best Power. On this card, the customer must indicate the serial numbers of the equipment that the UPS will be supporting. The card needs to be returned to the location specified on the back of the card, or to the fax number provided. See the Limited Warranty - Transient Voltage Surge Suppression Circuitry for details.

Battery Replacement

If the battery runtime should fall below 80 percent of the original time within the applicable 2-year or 5-year warranty period after a full and complete recharge cycle, the batteries will be replaced at no cost to the customer or IBM, under the terms and conditions of IBM Product and Support/Services Agreement A50005. The Battery Limited Warranty Period will be reduced by 50 percent for every 8 degrees C (15 degrees F) increase in

the

room ambient temperature

above 25 degrees C (77 degrees F). Battery claims are invalid if the battery is sub-

ject to misuse, abuse, or physical damage.

Unit Identification Numbers:

The label in the front left corner of the unit shows these identification numbers:

MN: The IBM Machine Type/Model Number PN: The IBM UPS Part Number SN: The IBM UPS Serial Number

Customers who call for service may be asked for their unit’s IBM UPS Serial Number.

Customer Process for Service

UNITED STATES (US)

1. The customer calls 1-800-IBMSERV. (IBM Call Management Center)

2. The customer indicates that the UPS is defective.

3. The Call Management Center will confirm that the unit is listed in the customer profile and notify Best Power.

4. Best Power will promptly call the customer and ask for the serial number. Best Power will also attempt to determine the nature of the problem. The problem may be related to improper operation as opposed to a defect.

5. If the unit requires replacement, Best Power will send a replacement unit via air express.

6. The customer is expected to install the replacement unit and return the defective unit to Best Power. The packaging material used for the replacement unit should be used for this purpose.

7. The shipping costs associated with returning the defective unit are the responsibility of the customer.

CANADA (Canada)

1. The customer calls 1-800-465-6666.

2. Dispatch takes the information from the customer and notifies IBM Customer Service Representative (CSR).

3. Problem determination is performed by the CSR.

4. If a replacement unit is required, the unit is ordered out of IBM stock and sent to the customer.

5. The Customer Service Representative (CSR) does a swap and returns the defective unit to the IBM parts center.

LATIN AMERICA DIVISION (LAD)

1. The customer calls the IBM office servicing the account.

2. The IBM Customer Engineer (CE) responds and determines and resolves the problem.

EUROPE, MIDDLE-EAST, AFRICA (EMEA)

1. The customer calls the IBM office servicing the account and describes the problem.

2. If a replacement unit is required, it will be sent by courier to the customer.

3. The customer is expected to return the defective unit to the local IBM office or as instructed.

Page 30

ASIA - PACIFIC (AP) COUNTRIES

1. The customer calls the Best Power office coordinating service for their account, or Best Power’s

Worldwide Service center at 1-608-565-2100 (or the customer sends e-mail to

service@bestpower.gen-

sig.com

2. The Best Service Organization responds, determines the problem, and resolves the problem.

Handling of Incomplete, Damaged, or Incorrectly Shipped 9910 UPSs (U.S. Only)

If the customer initially receives a 9910 UPS that is incomplete, damaged, or incorrectly shipped:

1. The customer contacts IBM at 1-800-IBMSERV (IBM Call Management Center) to report the problem.

2. An IBM representative notifies the customer of how the problem will be resolved.

Page 31

UPS Monitoring

UPS monitoring is a standard feature of the AS/400 operating system. QUPSDLYTIM is a timer in the AS/400 that tells the system how long to run on UPS power before shutting down. Each AS/400 system is initially assigned a default value for QUPSDLYTIM. Refer to the Uninterruptible Power Supply section in the IBM document “AS/400 Advanced Series Backup and Recovery - Advanced,” SC41-3305 (for AS/400 Models 2xx and 3xx), or “AS/400 Advanced Series Backup and Recovery - Advanced,” SC41-4305 (for AS/400 Models 4xx and 5xx) for information on determining what this value is for your system, or for assistance in changing the value of QUPSDLYTIM.

Caution: *NOMAX tells the AS/400 to use customized shutdown software, and if none is available it

will immediately begin shutdown when utility power fails. Do not set QUPSDLYTIM to “*NOMAX” unless you understand the implications of the *NOMAX function as described in “AS/400 Advanced Series Backup and Recovery - Advanced,” SC41-3305 (for AS/400 Models 2xx and 3xx), or “AS/400 Advanced Series Backup and Recovery - Advanced,” SC41-4305 (for AS/400 Models 4xx and 5xx).

Page 32

Changing the Fortress’ Inverter Voltage

This section describes how to change the Fortress’ inverter voltage using the front panel keys. (The inverter voltage is the voltage the Fortress supplies when it runs on battery power.)

If you’re not sure whether you need to change the Fortress’ inverter voltage, follow these steps:

a. Find the label on the back of the Fortress that shows the “Input” and “Output” voltages (VAC or volts

AC). Units labeled “110/115/120 VAC” are set to 120 volts at the factory. Units labeled “208 VAC” are set to 208 volts. Units labeled “220/230/240 VAC” are set to 230 volts at the factory. Write down the voltage your unit is set to: _____________

b. Find out the nominal voltage available at the outlet you will plug the Fortress into. Nominal voltage is

the voltage your electrical system is rated for. If you’re not sure what the nominal voltage is, ask your electrician. Write down the nominal voltage: _______

c. If a. and b. match, you do not need to change the Fortress’ inverter voltage. If not, change the

Fortress’ inverter voltage to match the nominal outlet voltage.

To change the voltage, read and follow these instructions carefully. If you have any questions or problems, please see the AS/400 UPS IBM Service Support section for the office to contact.

Read the tips below; then, follow the steps on the next few pages.

• Find the ID label on the back of your Fortress; then, check the voltage. If the voltage is 110, 115, or 120, do not change it to 100.

If the voltage is 220, 230 or 240, do not change it to 200 or 208.

• Usually, the Fortress’ display is off, but it switches on when you press the keys on the front panel. If you do

not press another key for about 60 seconds, the display will switch to runtime, and after another 30 seconds, the display will turn off to save power.

You may notice that the Fortress’ display turns off while you are reading some of the steps below. If this happens more than once, you may want to read through all of the steps before you start following the instructions.

• Before you change the voltage, make sure no equipment is plugged into the back of the Fortress.

The Fortress should be plugged in, and the On/Off (1/0) switch on the back of the Fortress should be on (1) so you can change the setpoints.

To change the voltage, follow these steps:

1. First, find out which type of Fortress you have: low-voltage or high-voltage. Low-voltage units supply 110, 115, or 120 volts. High-voltage units usually supply 220, 230 or 240 volts; special high-voltage units supply 208 volts. If you are not sure what voltage the UPS supplies now, check the ID label on the back of the Fortress.

2. You must change the Voltage Setpoint, the High Voltage Setpoint, and the Low Voltage Setpoint. Later steps will explain how to make these changes. For now, use one of the two tables on the next page to find the settings you will need for all three setpoints. Use Table 1 if you have a low-voltage UPS and Table 2 if you have a high-voltage UPS.

Page 33

Table 1: Low-Voltage Units

Example:

If you are changing the voltage to 115 volts, your new Voltage Setpoint setting should be “2”; the recommended Low Voltage setting would be “101,” and the recommended High Voltage setting would be “130.”

* Do not use 100-volt settings unless the UPS is specially designed for this voltage.

Table 2: High-Voltage Units

Example:

If you are changing the voltage to 240 volts, your new Voltage Setpoint setting should be “3”; the recommended Low Voltage setting would be “204,” and the recommended High Voltage setting would be “260.”

* Do not use 200 or 208-volt settings unless the UPS is specially designed for these voltages.

3. Write the settings you found in step 2 in the blanks below.

Setpoint Setting Voltage Setpoint __________ Low Voltage Setpoint __________ High Voltage Setpoint __________

4. Now, press the CANCEL and TEST keys at the same time for a few seconds. When you first press the keys,

the UPS will beep. After a few seconds, the Fortress will click, and the display will show “1 0”; this is the first level of setpoints. (Your Fortress Guide describes the setpoints in this level.)

The display shows “1 0”

Settings

New Voltage

Voltage Setpoint Low Voltage Setpoint High Voltage Setpoint

100 volts* 0 90 112

110 volts 1 96 125 115 volts 2 101 130 120 volts 3 105 136

260

253

204

196

240 volts

230 volts

2421871220 volts

2361820208 volts*

2201700200 volts*

High Voltage SetpointLow Voltage SetpointVoltage Setpoint

New Voltage

Settings

Press both keys to

display setpoints.

Page 34

5. Next, press CANCEL twice. The display will show setpoint “3” on the left and the setting (usually “2”) on the

right.

The display shows “3 2”

6. Press the CANCEL and %LOAD keys at the same time for a few seconds; the UPS will beep. After a few

seconds, the UPS will click. When this happens, the number on the left side of the display should change from “3” to “1”; the display is showing the second level of setpoints.

The display shows “1 0”

7. Now, press CANCEL. The left side of the display will show setpoint number “2” (blinking fast), and the right

side will show the setting, which is a number from 0-3. This is the Voltage Setpoint. The setting determines what voltage the Fortress supplies.

8. Check the setting you wrote down for the Voltage Setpoint in the first blank in step 3 (toward the bottom of

page 33). This will be the new Voltage setting. Change the setting:

To increase the setting, press the %LOAD key until the right side of the display shows the setting you need.

To lower the setting, press the V OUT key until the right side of the display shows the correct setting.

Note: If the display goes back to battery time (runtime) or shuts off before you can change the setting,

repeat steps 4-7; then, change the setting.

Press Cancel twice.

Press both keys.

Press to lower

setting (-).

Press to increase setting (+).

Press to record change (ENTER).

Page 35

Examples:

To change the voltage from 120 to 115 volts, press the V OUT key once. This lowers the setting from “3” to “2.”

To change the voltage from 220 to 240 volts, press the %LOAD key twice. This increases the setting from “1” to “3.”

9. To record the voltage change in the Fortress, press the TEST key. The setpoint number on the left will blink

more slowly.

10. If your UPS is an LI 660, 675, or 750, or if it is an LI 1.3K without extended battery time, go to step 13.

If your UPS is an LI 1.3K with extended battery time, press the CANCEL key once. The display should show “3” on the left side and a number from 60 to 250 on the right side. The setting (the number on the right) is the voltage that the UPS supplies when it runs on inverter (battery power).

11. Change the setting to the new voltage. To increase the setting, press the % LOAD key; to decrease the set-

ting, press the V OUT key.

12. To record the voltage change in the Fortress, press the TEST key. The setpoint number on the left will blink

more slowly.

13. Now you must change the settings of the Low Voltage and High Voltage setpoints (in the first setpoint level).

The Setpoint Table in the Fortress Guide describes these setpoints. To change the settings, follow the instructions below.

If the display still shows the setpoints, press CANCEL at least eight times until the display shows the Fortress’ runtime. (With no equipment plugged in, this will usually be “99:00”.) Once the display shows the battery time, go on to step 14.

If the display is off, or if the display shows the runtime, go on to step 14.

14. Press the CANCEL and TEST keys at the same time for a few seconds; the UPS will beep. After a few sec-

onds the UPS will click and display “1 0”. (This is the first setpoint level.)

The display shows “1 0”

Press Cancel.

Press to

lower

setting (-).

Press both keys to

display setpoints.

Press to increase

setting (+).

Press to record change (ENTER).

Page 36

15.Next, press the CANCEL key seven times until the number on the left side of the display (the setpoint number) is “8”. (This number should be blinking fast.) This is the Low Voltage setpoint. The number on the right is the Low Voltage setting.

Press Cancel seven times.

16.Now, check the second blank in step 3 toward the bottom of page 33 (Low Voltage Setpoint). The number you have written is the new Low Voltage setting. Change the number on the right side of the display to this setting.

(Press the V OUT key to lower the setting or the %LOAD key to increase the setting.)

Press to

lower

setting (-).

Press to increase setting (+).

Press to record change (ENTER).

17.Once you have the correct setting, press the TEST key to record the change in the UPS. The setpoint number on the left will blink more slowly.

18.Press the CANCEL key once. The display should show “9” on the left side (blinking fast). This is the High Voltage setpoint. The number on the right is the High Voltage setting.

19.Now, check the third blank in step 3 toward the bottom of page 33 (High Voltage Setpoint). The number you have written is the new High Voltage setting.

Change the setting. Press the V OUT key to lower the setting or the %LOAD key to increase the setting.

Press to

lower

setting (-).

Press to increase setting (+).

Press to record change (ENTER).

20.Once you have the correct setting, press the TEST key to record the change in the UPS. The setpoint number on the left will blink more slowly.

You have finished changing the voltage. If you do not press another key for about 60 seconds, the display will switch back to runtime, and after 30

more seconds, the display will turn off to save power. If you are following the installation steps, please return to step 17on page 21 of this Installation and Service

Guide.

Page 37

Limited Warranty

Transient Voltage Surge Suppression Circuitry (Only for Best Power UPS (IBM Machine Type 9910) purchased with IBM AS/400 computer systems)

BEST POWER, a division of General Signal Power Systems, Inc. (hereinafter called BEST POWER) hereby warrants the transient voltage surge suppression circuitry in each FORTRESS® product (hereinafter called “Product”) sold by IBM for installation with an IBM AS/400 computer system to be free from defects in material and workmanship under normal use and service for the lifetime of the Product, beginning with the date of sale to the initial retail purchaser, subject to the following conditions. This warranty is applicable only to the initial retail purchaser (hereinafter called PURCHASER), is not transferable, and is limited to the following remedies:

1. The replacement or repair of the transient voltage surge suppression circuitry in each Product that is returned intact to BEST POWER and which shall appear to BEST POWER upon inspection to have been defective in material or workmanship or to have been damaged through normal use;

2. The reimbursement to the PURCHASER of up to $25,000 per occurrence of documented physical damage to specified computer equipment connected to a Product where such damage could have been prevented by transient voltage surge suppression circuitry as detailed in BEST POWER’s specification for the Product sold.

This warranty is made in addition to BEST POWER’s Standard Limited Warranty. This warranty does not include any taxes which may be due in connection with replacement or repair nor any

installation, transportation or postage costs. These expenses will be paid by PURCHASER. Replacement or repair will be made at BEST POWER’s Worldwide Service, Highway 80, Necedah, Wisconsin 54646, U.S.A.

This warranty does not cover repair or replacement because of damage from unreasonable use (damage from road hazards, accident, fire or other casualty, misuse, negligence, incorrect wiring) and any use or installation not in conformance with instructions furnished by BEST POWER, or repairs or replacements needed because of modifications or parts not authorized or supplied by BEST POWER.

This warranty is operable only upon the written acceptance by BEST POWER of an application by the PURCHASER on BEST POWER’s standard form for the above warranty coverage for the Product sold. In such application, the PURCHASER shall represent that the Product sold has been properly installed and grounded in accordance with instructions received from BEST POWER, and the PURCHASER shall also specify the computer equipment to which the Product sold has been connected and the location of the computer equipment. This warranty will not apply to any equipment not specified in the application by the PURCHASER as protected equipment.

EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY AND BEST POWER’S STANDARD LIMITED WARRANTY, BEST POWER MAKES NO OTHER WARRANTIES, AND TO THE EXTENT ALLOWED BY LAW, BEST POWER DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

REMEDIES UNDER THIS WARRANTY ARE EXPRESSLY LIMITED TO THE REPAIR OR REPLACEMENT OF PRODUCTS AND THE REIMBURSEMENT SPECIFIED ABOVE, AND TO THE EXTENT ALLOWED BY LAW ANY CLAIMS FOR LOSS ARISING OUT OF THE FAILURE OF PRODUCTS TO PERFORM FOR ANY PERIOD OF TIME, OR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR OTHER ECONOMIC LOSS ARE EXPRESSLY EXCLUDED.

Some states do not allow limitations on how long an implied warranty lasts, so that the above limitation on duration of implied warranties may not apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. You are advised to consult applicable state laws.

Page 38

Part Numbers

Machine

Type

Model

IBM Part

Number

Best Power

Part Number

VA Watts Volts Frequency

Includes the following

items (see the table below)

9910 B08 85F8801 LI 660 BW 660 400 110-120 50-60 1, 3, 7, 9 9910 B09 85F8802 LI 660 DW 660 400 220-240 50-60 1, 2, 8, 9, 10 9910 B13 85F8806 LI 1.3K BW 1100 940 110-120 50-60 1, 4, 7, 9 9910 B14 85F8807 LI 1.3K DW 1300 940 220-240 50-60 1, 2, 8, 9, 10 9910 B24 21H1787 LI 660 BW 660 400 110-120 50-60 1, 3, 7, 9 9910 B26 21H1786 LI 660 DW 660 400 220-240 50-60 1, 2, 8, 9, 10 9910 B28 21H1788 LI 660 EW 660 400 208 50-60 1, 2, 7, 9 9910 B63 44H3967 LI 675 BWM 675 400 110-120 50-60 1, 3, 7, 9 9910 B64 44H3968 LI 675 DWM 675 400 220-240 50-60 1, 2, 8, 9, 10 9910 B67 44H3969 LI 750 BWM 750 750 110-120 50-60 1, 3, 7, 9 9910 B68 44H3970 LI 750 DWM 750 750 220-240 50-60 1, 2, 8, 9, 10 9910 B69 44H3971 LI 1.3K BWN 1100 940 110-120 50-60 1, 4, 7, 9 9910 B70 44H3972 LI 1.3K DWN 1300 940 220-240 50-60 1, 2, 8, 9, 10

Accessories

Item IBM Part Description Best Power Part Number

1 85F8815 Fortress AS/400 cable IPK0303 2 21H1576 IEC-IEC Power Jumper Cable (UL/VDE) LCA0251 3 85F8817 IEC-NEMA Power Cord (UL/cUL, 10-amp) LCA0182 4 21H8493 IEC-NEMA Power Cord (UL/cUL, 15-amp) LCA0183 5 44H3973 675, 750 Battery Accessory Cabinet LIEBP2W 6 44H3974 1.3K Battery Accessory Cabinet LIEBPW

Manuals

Manuals may be ordered from Mechanicsburg or Copenhagen.

Item IBM Order Number Description Best Power Part Number

7 SA21-9645 Fortress User’s Guide (100-120V and 208V) MLS-0380 8 SA21-9642 Fortress User’s Guide (200-240V) IMS-0401

9 SA21-9644

Fortress AS/400 UPS Installation and

Service Guide

MLS-0048

10 — Notice to 240V Users MLS-0056

Fortress Technologies AS/400 Installation And Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual