Fortinet FortiGate 30B User Manual

INSTALL GUIDE

FortiGate-30B FortiOS 3.0 MR6

www.fortinet.com

FortiGate-30B Install Guide

FortiOS 3.0 MR6 5 May 2008 01-30006-0459-20080505

© Copyright 2008 Fortinet, Inc. All rights reserved. No part of this publication including text, examples, diagrams or illustrations may be reproduced, transmitted, or translated in any form or by any means, electronic, mechanical, manual, optical or otherwise, for any purpose, without prior written permission of Fortinet, Inc.

Trademarks

Fortinet, FortiGate and FortiGuard are registered trademarks and Dynamic Threat Prevention System (DTPS), APSecure, FortiASIC, FortiBIOS, FortiBridge, FortiClient, FortiGate, FortiGate Unified Threat Management System, FortiGuard-Antispam, FortiGuard-Antivirus, FortiGuard-Intrusion, FortiGuard-Web, FortiLog, FortiAnalyzer, FortiManager, FortiOS, FortiPartner, FortiProtect, FortiReporter, FortiResponse, FortiShield, and FortiVoIP, are trademarks of Fortinet, Inc. in the United States and/or other countries. The names of actual companies and products mentioned herein may be the trademarks of their respective owners.

Regulatory compliance

FCC Class A Part 15 CSA/CUS .

Caution: Risk of Explosion if Battery is replaced by an Incorrect Type.

Dispose of Used Batteries According to the Instructions.

Conents

Conents............................................................................................... 3

Introduction........................................................................................ 7

About the FortiGate-30B ................................................................................... 8

About this document......................................................................................... 8

Document conventions ................................................................................. 9

Typographic conventions .............................................................................. 9

Further Reading................................................................................................. 9

Fortinet Knowledge Center ......................................................................... 10

Comments on Fortinet technical documentation......................................... 10

Customer service and technical support ...................................................... 11

Installing ........................................................................................... 13

Environmental specifications......................................................................... 13

Cautions and warnings................................................................................... 14

Grounding ................................................................................................... 14

Rack mount instructions.............................................................................. 14

Mounting ..................................................................................................... 14

Plugging in the FortiGate................................................................................ 15

Connecting to the network .......................................................................... 15

Turning off the FortiGate unit......................................................................... 15

Configuring....................................................................................... 17

NAT vs. Transparent mode............................................................................. 17

NAT mode................................................................................................... 17

Transparent mode....................................................................................... 18

Connecting to the FortiGate unit ................................................................... 18

Connecting to the web-based manager ...................................................... 18

Connecting to the CLI ................................................................................. 19

Configuring NAT mode ................................................................................... 20

Using the web-based manager ................................................................... 20

Configure the interfaces ....................................................................... 20

Configure a DNS server ....................................................................... 21

Adding a default route and gateway..................................................... 21

Adding firewall policies ......................................................................... 22

Using the CLI .............................................................................................. 23

Configure the interfaces ....................................................................... 23

FortiGate-30B FortiOS 3.0 MR6 Install Guide

3 01-30006-0459-20080505

Conents

Configure a DNS server ....................................................................... 24

Adding a default route and gateway..................................................... 24

Adding firewall policies ......................................................................... 25

Configuring Transparent mode...................................................................... 25

Using the web-based manager ................................................................... 26

Switching to Transparent mode............................................................ 26

Configure a DNS server ....................................................................... 26

Adding firewall policies ......................................................................... 26

Using the CLI .............................................................................................. 27

Switching to Transparent mode............................................................ 27

Configure a DNS server ....................................................................... 28

Adding firewall policies ......................................................................... 28

Verify the configuration .................................................................................. 29

Backing up the configuration......................................................................... 29

Restoring a configuration............................................................................... 30

Additional configuration ................................................................................. 30

Set the time and date.................................................................................. 30

Set the Administrator password .................................................................. 30

Configure FortiGuard .................................................................................. 31

Updating antivirus and IPS signatures ................................................. 31

Advanced configuration.................................................................. 33

Protection profiles........................................................................................... 33

Firewall policies............................................................................................... 34

Configuring firewall policies ........................................................................ 35

Antivirus options............................................................................................. 35

AntiSpam options............................................................................................ 36

Web filtering..................................................................................................... 37

Logging ............................................................................................................ 38

FortiGate Firmware.......................................................................... 39

Downloading firmware .................................................................................... 39

Using the web-based manager....................................................................... 40

Upgrading the firmware............................................................................... 40

Reverting to a previous version .................................................................. 40

Backup and Restore from a USB key ......................................................... 41

Using the USB Auto-Install ......................................................................... 41

Using the CLI ................................................................................................... 42

Reverting to a previous version .................................................................. 43

FortiGate-30B FortiOS 3.0 MR6 Install Guide

4 01-30006-0459-20080505

Conents

Installing firmware from a system reboot using the CLI.............................. 44

Restoring the previous configuration........................................................... 46

Backup and Restore from a USB key ......................................................... 46

Using the USB Auto-Install.......................................................................... 47

Additional CLI Commands for a USB key ................................................... 47

Testing new firmware before installing ......................................................... 48

Index.................................................................................................. 51

FortiGate-30B FortiOS 3.0 MR6 Install Guide 01-30006-0459-20080505 5

Conents

FortiGate-30B FortiOS 3.0 MR6 Install Guide

6 01-30006-0459-20080505

Introduction Register your FortiGate unit

Introduction

Welcome and thank you for selecting Fortinet products for your real-time network protection.

The FortiGate Unified Threat Management System improves network security, reduces network misuse and abuse, and helps you use communications resources more efficiently without compromising the performance of your network. The FortiGate Unified Threat Management System are ICSA-certified for firewall, IPSec, and antivirus services.

The FortiGate Unified Threat Management Systemis a dedicated, easily managed security device that delivers a full suite of capabilities, which include:

• application-level services such as virus protection and content filtering

• network-level services such as firewall, intrusion detection, VPN and traffic shaping

The FortiGate Unified Threat Management System uses Fortinet’s Dynamic Threat Prevention System (DTPS™) technology, which leverages breakthroughs in chip design, networking, security and content analysis. The unique ASIC-based architecture analyzes content and behavior in real-time, enabling key applications to be deployed right at the network edge where they are most effective at protecting your networks.

Register your FortiGate unit

To register, enter your contact information and the serial numbers of the FortiGate units that you or your organization have purchased. You can register multiple FortiGate units in a single session without re-entering your contact information.

By registering your FortiGate unit, you will receive updates to threat detection and prevention databases (Antivirus, Intrusion Detection, etc.) and will also ensure your access to technical support.

For more information, see the Fortinet Knowledge Centre article “Registration Frequently Asked Questions” (http://kc.forticare.com/default.asp?id=2071).

FortiGate-30B FortiOS 3.0 MR6 Install Guide 01-30006-0459-20080505 7

About the FortiGate-30B Introduction

About the FortiGate-30B

The FortiGate-30B provides a WAN port for connection to the Internet and three integrated switch ports for multiuser environments in a small remote office. It is ideally suited for remote offices, retail stores, broadband telecommuter sites and many other applications.

The FortiGate-30B provides complete real-time network protection through a combination of network-based antivirus, web and email content filtering, firewall, VPN, network-based intrusion detection and prevention, and traffic shaping.

Figure 1: FortiGate-30B

USB

STATUS WAN

INTERNAL

123POWER

As a firewall for use in small offices, the FortiGate unit has a reduced feature set to maximize its efficiency as a remote firewall appliance.

These features include:

• dynamic routing (BGP, OSPF, RIP, and PIM)

• virtual domains (VDOMs)

• virtual LANs (VLAN)

• high availability (HA)

• SSL VPN

• dual WAN fail over

• traffic shaping

• server load balancing

Note: The default management port on the FortiGate-30B is port 3.

About this document

This document explains how to install and configure your FortiGate unit onto your network. This document also includes how to install and upgrade new firmware versions on your FortiGate unit.

This document contains the following chapters:

• Installing – Describes setting up and powering on a FortiGate unit.

• Configuring – Provides an overview of the operating modes of the FortiGate unit and how to integrate the FortiGate unit into your network.

• Advanced configuration – Describes additional configuration you can perform on the FortiGate unit to enhance network protection, including antivirus, antispam, firewall configuration and logging.

• FortiGate Firmware – Describes how to install, update, restore and test firmware for the FortiGate device.

FortiGate-30B FortiOS 3.0 MR6 Install Guide

8 01-30006-0459-20080505

Introduction Further Reading

Document conventions

The following document conventions are used in this guide:

• In the examples, private IP addresses are used for both private and public IP addresses.

• Notes and Cautions are used to provide important information:

Note: Highlights useful additional information.

Caution: Warns you about commands or procedures that could have unexpected or

undesirable results including loss of data or damage to equipment.

Typographic conventions

FortiGate documentation uses the following typographical conventions:

Convention Example Keyboard input In the Gateway Name field, type a name for the remote VPN

Code examples config sys global

CLI command syntax config firewall policy

Document names FortiGate Administration Guide Menu commands Go to VPN > IPSEC > Phase 1 and select Create New. Program output Welcome! Variables

peer or client (for example, Central_Office_1).

set ips-open enable

end

edit id_integer

set http_retry_count <retry_integer> set natip <address_ipv4mask>

end

<address_ipv4>

Customer service and technical support

Fortinet Technical Support provides services designed to make sure that your Fortinet systems install quickly, configure easily, and operate reliably in your network.

Please visit the Fortinet Technical Support web site at http://support.fortinet.com to learn about the technical support services that Fortinet provides.

FortiGate-30B FortiOS 3.0 MR6 Install Guide 01-30006-0459-20080505 11

Customer service and technical support Introduction

FortiGate-30B FortiOS 3.0 MR6 Install Guide

12 01-30006-0459-20080505

Installing Environmental specifications

Installing

This chapter describes installing your FortiGate unit in your server room, environmental specifications and how to mount the FortiGate in a rack if applicable.

This chapter contains the following topics:

• Environmental specifications

• Cautions and warnings

• Plugging in the FortiGate

• Turning off the FortiGate unit

Environmental specifications

• Operating temperature: 32 to 104°F (0 to 40°C) If you install the FortiGate unit in a closed or multi-unit rack assembly, the

operating ambient temperature of the rack environment may be greater than room ambient temperature. Therefore, make sure to install the equipment in an environment compatible with the manufacturer's maximum rated ambient temperature.

• Storage temperature: -13 to 158°F (-25 to 70°C)

• Humidity: 5 to 90% non-condensing

• Air flow - For rack installation, make sure that the amount of air flow required for safe operation of the equipment is not compromised.

• For free-standing installation, make sure that the appliance has at least 1.5 in. (3.75 cm) of clearance on each side to allow for adequate air flow and cooling.

This device complies with part FCC Class A, Part 15, UL/CUL, C Tick, CE and VCCI. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and

• This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

FortiGate-30B FortiOS 3.0 MR6 Install Guide 01-30006-0459-20080505 13

Cautions and warnings Installing

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

The equipment compliance with FCC radiation exposure limit set forth for uncontrolled Environment.

Cautions and warnings

Review the following cautions before installing your FortiGate unit.

Grounding

• Ensure the FortiGate unit is connected and properly grounded to a lightning and surge protector. WAN or LAN connections that enter the premises from outside the building should be connected to an Ethernet CAT5 (10/100 Mb/s) surge protector.

• Shielded Twisted Pair (STP) Ethernet cables should be used whenever possible rather than Unshielded Twisted Pair (UTP).

• Do not connect or disconnect cables during lightning activity to avoid damage to the FortiGate unit or personal injury.

Rack mount instructions

Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly,

the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.

Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised.

Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.

Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.

Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained.

Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).

Mounting

If required to fit into a rack unit, remove the rubber feet from the bottom of the FortiGate unit.

Adhere the rubber feet included in the package to the underside of the FortiGate unit, near the corners of the device.

FortiGate-30B FortiOS 3.0 MR6 Install Guide

14 01-30006-0459-20080505

Installing Plugging in the FortiGate

Place the FortiGate unit on any flat, stable surface. Ensure the unit has sufficient clearance on each side to ensure adequate airflow for cooling.

Plugging in the FortiGate

Use the following steps to connect the power supply to the FortiGate unit.

To power on the FortiGate unit 1 Connect the AC adapter to the power connection at the back of the FortiGate unit. 2 Connect the AC adapter to the power cable. 3 Connect the power cable to a power outlet.

The FortiGate unit starts and the Power and Status LEDs light up. The Status

LEDs flash while the FortiGate unit starts up, and remain lit when the system is

running.

Connecting to the network

Using the supplied Ethernet cable, connect one end of the cable to your router or

modem, whatever the connection is to the Internet. Connect the other end to the

FortiGate unit. Connect to either the External, WAN port, or port 1. Connect

additional cable to the Internal port or port 2 and your internal hub or switch.

Turning off the FortiGate unit

Always shut down the FortiGate operating system properly before turning off the

power switch to avoid potential hardware problems.

To power off the FortiGate unit 1 From the web-based manager, go to System > Status. 2 In the Unit Operation display, select Shutdown, or from the CLI enter:

execute shutdown

3 Disconnect the power cables from the power supply.

FortiGate-30B FortiOS 3.0 MR6 Install Guide 01-30006-0459-20080505 15

Turning off the FortiGate unit Installing

FortiGate-30B FortiOS 3.0 MR6 Install Guide

16 01-30006-0459-20080505

Configuring NAT vs. Transparent mode

Configuring

This section provides an overview of the operating modes of the FortiGate unit,

NAT/Route and Transparent, and how to configure the FortiGate unit for each

mode. There are two ways you can configure the FortiGate unit, using the

web-based manager or the command line interface (CLI). This section will step

through using both methods. Use whichever you are most comfortable with.

This section includes the following topics:

• NAT vs. Transparent mode

• Connecting to the FortiGate unit

• Verify the configuration

• Backing up the configuration

• Additional configuration

NAT vs. Transparent mode

NAT mode

The FortiGate unit can run in two different modes, depending on your network

infrastructure and requirements. You have a choice between NAT/Route mode

and Transparent mode. Both include the same robust network security features

such as antispam, antivirus, VPN and firewall policies.

In NAT/Route mode, the FortiGate unit is visible to the network. Like a router, all

its interfaces are on different subnets.

In NAT mode, each port is on a different subnet, enabling you to have a single IP

address available to the public Internet. The FortiGate unit performs network

address translation before it sends and receives the packet to the destination

network.

In Route mode, there is no address translation.

Figure 2: FortiGate unit in NAT mode

Internal network

Internet

Router

NAT mode policies controlling

traffic between internal

and external networks.

192.168.1.99204.23.1.5

192.168.1.20

You typically use NAT/Route mode when the FortiGate unit is operating as a

gateway between private and public networks. In this configuration, you would

create NAT mode firewall policies to control traffic flowing between the internal,

private network and the external, public network, usually the Internet.

FortiGate-30B FortiOS 3.0 MR6 Install Guide 01-30006-0459-20080505 17

+ 39 hidden pages

Fortinet FortiGate 30B User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Conents

Introduction

Register your FortiGate unit

About the FortiGate-30B

About this document

Document conventions

Typographic conventions

Further Reading

Fortinet Knowledge Center

Comments on Fortinet technical documentation

Customer service and technical support

Installing

Environmental specifications

Cautions and warnings

Grounding

Rack mount instructions

Mounting

Plugging in the FortiGate

Connecting to the network

Turning off the FortiGate unit

Configuring

NAT vs. Transparent mode

NAT mode