Formax FD 8712HS High
Security Optical Media
Shredder
Instruction Manual
Safety Devices and Other Features
Formax 8000 Series Shredders are equipped with various safety features:
Automatic Reverse Rotation (Process takes about 6 to 8 seconds)
When too much media is inserted, the cutter stops operating and
automatically rotates in reverse to discharge the jammed media. An
alarm sounds. Clear the media an re-insert. If it continues to auto
reverse the shredder head should be oiled and cleaned (see below).
Door Switch
If the door is open, the shredder will not operate.
Automatic Stop
When the shredded media lls the waste bin, the “FULL” light comes
on and the cutter stops operation. Open the door, remove the waste
bin and empty media shreds. Replace the waste bin, close the door
and continue operation.
Automatic Power Shut-Off
• If the shredder operates continuously for more than 30 minutes,
the power is automatically shut off.
• If the motor is overloaded, the “ECO MODE” LED will ash until it
cools down. When the ashing stops the shredder is ready to be
used again.
Oil Indicator
High Security CD/DVD Shredder
FD 8712HS
Oil regularly for peak performance. NOTE: The “MANUAL” LED will ash after
every four (4) hours of operation as an indicator to oil the shredder cutting blades.
The LED will continue to ash until oiled. NOTE: the shedder will still operate when
the LED is ashing but at a decreased load capacity.
To oil: Spread shredder oil onto the cutters through the feed opening, and allow the
oil to sit for a few minutes to permeate the cutting blades, then press the “REV” button
and hold for ve seconds. “MANUAL” and “REV” LED indicators on control panel will
light. The shredder will operate in reverse for one minute, then the “AUTO” LED will
light indicating the shredder is ready.
Maintenance
• Disconnect power by pulling power cord plug from wall outlet.
• To clean the exterior, wipe the surface with a soft cloth. If the surface is very dirty,
use a neutral detergent, then wipe again with a soft cloth.
CAUTION:
• Never put water directly on the surface of the shredder.
• Never clean the case with benzene or thinner, since it will cause discoloration.
• Do not dismantle the shredder. Contact your Formax Dealer for service.
NSA Approved: Meets NSA/CSS Specication 04-02 for High Security
Optical Media Destruction Devices
MyBinding.com
1/2015
5500 NE Moore Court
Hillsboro, OR 97124
OPERATOR MANUAL
FIRST EDITION
Toll Free: 1-800-944-4573
Local: 503-640-5920
Specications
Cutting Style: Cross Cut
Shred Size: 1/16” x 5/32”
Sheet Capacity: 1 CD-R, CD-RW, CD-ROM or DVD
Speed: 1,068 optical discs per hour
Feed Opening: 4 7/8”
Dimensions: 20” W x 20” D x 34” H
Bin Capacity: 28 gal.
Security Level: O-6, Meets NSA/CSS Specication 04-02 for High
Security Optical Media Destruction Devices
Weight: 176 lbs.
Power supply: 110-120V, 60Hz
ECO Mode
When the power switch on the right side of the shredder (see below) is initially turned
on, the shredder is automatically in ECO Mode. This energy-saving feature puts the
shredder into standby after 5 minutes of inactivity.
When the shredder is in standby, the ECO Mode LED on the
control panel will be lit.
To exit ECO Mode: Turn the power switch to the off position, then while pressing the
stop button turn the shredder back on, hold the stop button down until the shredder
beeps once and release. The Eco Mode indicator LED will go out indicating that the
shredder is no longer in Eco Mode. To re-engage Eco Mode simply turn the shredder
off and then back on.
Safety Precautions
Set-up Guidelines
1. Install the shredder on a level surface, away from heat sources and direct sunlight.
2. Insert plug into wall outlet with the appropriate voltage, 110V. If the outlet is shared
with another electronic device, the total current should not exceed 30A (at 110V).
Operation
1. Flip the power switch “ON” located on the right side of the shredder.
2. Auto Start/Auto Stop
When the START button is pushed, the “AUTO” LED will light. Insert
media to shred. The shredder will start and stop automatically when
using this function.
3. Manual Operation
If the optical media is too small for the shredder’s sensors to detect,
shred it manually. Push the START button once more and the
“MANUAL” LED will light. Insert media to be shredded. Three minutes
after shredding, the cutter automatically stops rotating.
4. Reverse Operation
Push the REV button and the “REV” LED will light and cutters will
operate in reverse.
5. Full Sensor
If the wastebasket is full, the “FULL” LED will light and the cutter will
stop automatically. Open the door, remove and empty the waste bin.
Replace the waste bin, close door, and press START to resume shredding.
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
To avoid personal injury, and damage to the shredder, observe the following safety
precautions. Please keep these instructions for future reference.
NOTE: In case of emergency, push the
“Power Switch” to cut off power and/or pull
the plug out of the wall outlet.
• Keep hands, long hair, clothing, ties, jewelry
and loose items away from the feed opening
and shred outlet.
• Do not use the shredder for anything other
than its intended purpose. DO NOT SHRED STAPLES OR PAPER CLIPS, THEY
WILL DAMAGE OR DESTROY THE CUTTING BLADES.
• Do not allow children to use the machine.
• Do not operate with a damaged power cord or plug, or when the machine is
damaged in any manner.
• Unplug the shredder when it is being moved, or if it is not in use for an extended
period of time.
• Do not disconnect the power by pulling only the cord. Hold the plug when
disconnecting.
• Keep the shredder away from direct sunlight.
• Do not sit on the shredder or place anything on top of it.
• Never open the xed switch or cover.
Loading...