Follett HCD1810NBS, HCF1810RBS, HCF1810RBT, HCD1810RBT, HCF1810RJS Installation Manual

HC_1810R/N, HM_1810R/N
HC_2110R/N, HM_2110R/N

Order parts online
www.follettice.com

Horizon Elite™ Ice Machine Installation Instructions

for Remote Condensing Unit

Drop-in Remote Condensing

®

RIDE

remote ice delivery equipment

Vision™ Remote Condensing

RIDE remote ice delivery equipment

801 Church Lane • Easton, PA 18040, USA
Toll free [phone] • [phone]

REMOTE CONDENSING UNIT

www.follettice.com

Harmony Remote Condensing

Top Mount

Harmony™ Remote Condensing

RIDE remote ice delivery equipment

Bin Remote Condensing

Top Mount

Bin Remote Condensing

RIDE remote ice delivery equipment

01157932R01

1

air in

exhaust

48.00"

(121.9cm)

48.00"

(121.9cm)

24.00"

(61.0cm)

24.00"

(61.0cm)

Condensing Unit Shipping Weight

Model Horizon 1810 Horizon 2110

Single-phase 305 lb (1139 kg) 305 lb (1139 kg)
3-phase 305 lb (1139 kg) 305 lb (1139 kg)

Prior to installation, carefully unpack and inspect the
contents of your condensing unit!

Site preparation

To ensure proper performance, ease of service and warranty coverage, it is critical that you follow
the requirements detailed in this manual. If you cannot meet these requirements or have questions,
call our technical service group at 877.612.5086 for installation support.

1

2.1

1. 1

Condenser Unit Clearances

• Position condenser unit as shown above, with clearances noted above

2

REMOTE CONDENSING UNIT

2.1

1. 2

Condenser installation specications

S-trap

required

Easton Pennsylvania

CORPORATION

PART NO

SERIAL NO

MODEL

SINGLE

FULL LOAD AMPS

HZ

VOLTS

PHASE

MOTOR COMPRESSOR THERMALLY PROTECTED

OZ

CHARGE

REFRIGERANT

PSIG

DESIGN PRESSURE HIGH SIDE

LOW SIDE

208264

MIN. BRANCH CIRCUIT AMPACITY

AMPS

Stock Module Identification Plate

MADE IN

ULU

NSF

THE USA

L

RR

Module No.

MAX. BRANCH CIRCUIT FUSE SIZE

AMPS

C

Product

Service No.

EVAPORATOR

UNIT

➊

➊

P-trap
required

P-trap
required

EVAPORATOR UNIT LEVEL

75' max.
(22.8 m)

➍

CONDENSER UNIT

maximum

line rise

CONDENSER UNIT

maximum

line drop

➋

+35'

(+10.7 m)

+20'

(+6.1 m)

–15'

(–4.6 m)

75' max.
(22.8 m)

➌

➍

Site layout:

• Outdoor ambient temperature range: –20 F to 120 F (–29 C to 49 C)

• Installation with condenser unit elevations above 20' (6.1 m) require an S-trap at the midpoint
of the rise and a P-trap at the top and bottom of the rise

➊

• Maximum line rise must not exceed 35' (10.7 m) ➋

• Maximum line set length must not exceed 75' (22.8 m)

• Maximum line drop must not exceed 15' (4.6 m)

➍

➌

REMOTE CONDENSING UNIT

3

Condenser installation

2

2.1

• Level unit

• Securely attach base of unit using holes

• Required rack system capacity at 0 F

1810N: 15,700 Btu/hr (3956 kcal/hr)

2110N: 18,200 Btu/hr (4586 kcal/hr)

Install condensing unit

found in base plate

(–18C) evaporator (EPR supplied by
installer).

2.2

Electrical requirements

Condensing unit

1810

Single-Phase

Electrical 208-230V, 60Hz

Max Circuit HVACR breaker size 45A 25A 45A 30A

Min Circuit Ampacity 26.2A 15.7A 27.1A 19.9A

• Refer to wiring schematic located in condenser unit electrical box

1810

3-Phase

2110

Single-Phase

2110

3-Phase

CAUTION

• Electrical disconnects required within
10' (3 m) for all hard wired connections

• Install in accordance with NEC and local
electrical codes

4

REMOTE CONDENSING UNIT