Follett HCD1810RBT, HCF1810RBT, HCD2110NBT, HCF2110RBT Installation Manual

Horizon Elite™ Ice Machine Installation Instructions

for Ice Storage Bin Top-mount Applications

HCD/HMD/HCF/HMF1810RBT, HCD/HMD/HCF/HMF2110RBT,
HCD1810NBT, HMD1810NBT, HCD2110NBT, HMD2110NBT

(See model number congurator on page 2 for details.)

Order parts online
www.follettice.com

remote condensing

801 Church Lane • Easton, PA 18040, USA
Toll free [phone] • [phone]
www.follettice.com

01157908R01

Chewblet® Ice Machine Model Number Configurations

HC 1810D SVA

CondenserSeriesVoltageIcemaker

MC Maestro™

Chewblet
(425 Series)

HC Horizon

Chewblet
(710, 1010,
1410, 1810,
2110 Series)

HM Horizon

Micro Chewblet

C 208-230/60/1 (icemaking head)

®

Self-contained only.

D 115/60/1 (icemaking head)

Self-contained and remote. If remote
unit, high side is 208-230/60/1.

E 230/50/1 (icemaking head)

Self-contained only.

F 115/60/1 (icemaking head)

Remote only. High side is
208-230/60/3.

425 up to

425 lbs
(193 kg)

710 up to

675 lbs
(306 kg)

1010 up to

1061 lbs
(482 kg)

1410 up to

1466 lbs
(665 kg)

1810 up to

1790 lbs
(812 kg)

2110 up to

2039 lbs
(925 kg)

A Air-cooled, self-contained
W Water-cooled, self-contained
R Air-cooled, remote condensing unit
N Air-cooled, no condensing unit for

connection to parallel rack system

V Vision™
H Harmony™
B Ice storage bin
J Drop-in
M Ice Manager

diverter valve
system

P Cornelius Profile

PR150

S RIDE™

T Top-mount

CAUTION!

§ This appliance should be connected by a qualied person in accordance with applicable codes.

§ If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualied persons in order to avoid a hazard.

§ Connect to potable water supply only.

§ This appliance can be used by children aged 8 years and above and persons with reduced physical,
sensory, or mental capabilities, or lack of experience and knowledge if they have been given supervision
or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children
should be supervised to ensure that they do not play with the appliance.

§ This appliance is intended to be used for household and similar applications such as staff kitchen areas
in shops, offices and other working environments; farm houses and by clients in hotels, motels and other
residential type environments; bed and breakfast type environments; catering and similar non-retail
applications.

§ WARNING! To avoid a hazard due to instability of the appliance, it must be xed in accordance with the
instructions.

ConfigurationApplication

(RIDE remote
ice delivery
equipment)

2

remote condensing BIN • TOP-MOUNT

Read and complete the following 8 installation steps

Unpack

1

Bin preparation

3

Ice transport tube

5

Site preparation

2

Louvered docking assembly

4

External connection

6

Internal connection

7

Front cover

8

BIN • TOP-MOUNT remote condensing

3

Carefully unpack and inspect the contents of your Follett ice machine.

Unpack

1

1. 1

Unpack ice machine

➊

➍

➋

7/16"

➌

➎

DO NOT TILT ICE MACHINE
TO ACCESS BOLTS!

7/16"

➏

4

COMPRESSOR DAMAGE
WILL RESULT

➐

remote condensing BIN • TOP-MOUNT

Site preparation

1" Stand pipe/Drain

3/4" MPT x 1" slip

➍

3/4" barb x 3/4" FPT

2 ft. x 1" OD

silicone tubing

Minimum 8"

radius

➌

Prepare the installation site.

Provide drainage, water supply and electrical power to within 6 feet (2m) of ice
machine in accordance with local and national codes. Outdoor installation is
not recommended and will void warranty.

2

2.1

2.1

Installation site requirements

3/8" ∅ (9,5mm)

➎

7/8" ∅ (22,4 mm)

➍

➊

➋

Electrical ➊

• 120/60/1-5 amps

Potable water supply ➋ (3/8” push-in internal connection, 3/8” OD tubing required)

• 10-70 psi (69-483kpa)

• 45-90 F (7-32 C)

• Follett recommends the use of an in-line water ltration system (item# 00130286)

• This equipment is to be installed with adequate backow protection to comply with applicable federal,

Drain ➌ (3/4” Barb)

• Minimum 8” radius on silicone drain line. Drain line from the ice machine must have at least 1/4” per foot

pitch (6,4mm/0,3m).

Refrigeration lines

• 7/8” ∅ (22,4 mm) diameter suction line (insulated)

• 3/8” ∅ (9,5 mm) liquid line

BIN • TOP-MOUNT remote condensing

state, and local codes

➍

➎

➌

➍

1'

1/4" per foot
(6,4 mm per 0,3 m)

NEMA

5-15

5

Prepare the bin.

Bin preparation

3

3.1

• Remove protective tape from

Bin top preparation

gaskets

3.2

Bin top preparation

➋

• Apply gaskets

• Install shuttle actuator
and secure with locking nut

➊

➊

➊

through bin top

➋

➌

➌

BEFORE PROCEEDING

Prior to installing the louvered docking
assembly, ensure that the drain tting is
oriented (right or left) correctly for your
installation. An optional straight drain tting
is also supplied. You may need to remove
the back panel of the docking assembly in
order to re-orient or change the drain tting.
Replace back panel prior to mounting the
docking assembly.

6

remote condensing BIN • TOP-MOUNT

Install the louvered docking assembly.

2" (50,8 mm)

Stub Typ

1.81" (46 mm)

3.75" (95.3 mm)

2" (50,8 mm)

Louvered docking assembly

4

2.1

4.1

3/8˝ ∅

high pressure

Louvered docking assembly

line

7/8" ∅ low pressure line

➋

• Mount louvered docking assembly

• “Rough-in” the refrigerant piping

➋

BIN • TOP-MOUNT remote condensing

➊

7

Install the ice transport tube.

5.1

Ice transport tube

➋

Hot Water

160 F (71 C)

➊

5

➌

• Slide insulation onto ice transport tube

• Heat end of transport tube in cup of 160 F (71 C) hot water to soften and spread with
pliers

• Connect ice transport tube to coupling on louvered docking station

• Connect ice transport tube to shuttle actuator

before making connection to ease assembly

➊

➌

➋

8

remote condensing BIN • TOP-MOUNT

Connect utilities to louvered docking assembly.

External connections

6

6.1

➋

Water and drain

➊

➌

➏

2 ft. x 1" OD

silicone tubing

3/4" barb x 3/4" FPT

➍

3/4" MPT x 1" slip

1" Stand pipe/Drain

➎

Minimum 8"

radius

6.2

Refrigerant lines

➊

• Braze supplied quick-connect lines onto
stub-ins

➊

.

• Rough-in ice machine potable water
supply
3/8” push-in connection will be made at
shut-off valve inside machine

• Remove access panel if necessary

• Connect the silicone tubing to the ice
machine 3/4” drain barb

• Assemble the 3/4” barb x 3/4” FPT to the
3/4” MPT x 1” slip. Connect the other end
of the silicone tubing to the 3/4” barb

• Connect the 1” slip tting to the 1” stand
pipe/drain

Note: Minimum 8” radius on silicone

drain line. Drain line from the ice machine
must have at least 1/4” per foot pitch
(6,4mm/0,3m).

• Apply Petrol-gel to barbed drain tting

• Replace access panel.

➊

.

➎

➋.

.

➌

.

➍

.

➏

BIN • TOP-MOUNT remote condensing

9

Connect louvered docking assembly to ice machine.

➊

Internal connections

7

7. 1

Ice transport tube installation

➋

➊

• Slide ice machine into louvered docking
assembly ensuring that drain tube is fully
seated on barbed drain tting

• Insert ice transport tube all the way into
coupling and tighten nut rmly

➊

➋

7. 2

• Insert potable water line into valve

Water line

➊

7. 3

Refrigeration lines

➊

• Evacuate line set.

• Connect self-sealing liquid and suction
line ttings

➊

10

7. 4

• Remove twist tie

• Carefully pass cord thru opening and plug

remote condensing BIN • TOP-MOUNT

Power cord

into wall outlet

7. 5

CLEAN

Power cord

7. 6

SERVICE

MAINT/CLEAN

TDS switch

LOW WATER

TIME DELAY

SLEEP CYCLE

MAKING ICE

LOW BIN

POWER ON

TDS

HIGH

LOW

• Position plate into opening and secure
with supplied screw

• Set the TDS switch on the electrical box:

HIGH: for extended service life

LOW: for low-scale water

BIN • TOP-MOUNT remote condensing

11

Install front cover to ice machine.

Front cover

8

8.1

• Complete installation of condensing unit

• Required rack system capacity at 0 F

1810N: 15,700 Btu/hr (3956 kcal/hr)

2110N: 18,200 Btu/hr (4586 kcal/hr)

Install condensing unit

or connection to rack system.

(-18C) evaporator (EPR supplied by
installer).

8.2

• Slide ice machine cover over machine

• Insert and tighten two screws through

Install ice machine front cover

➋

ensuring that tabs on back of cover
slip under louvers on back of louvered
docking assembly

cover and into louvered docking assembly

➊

➊

➋

NOTICE

Ice machine MUST be sanitized prior to operation!

Consult Operation and Service Manual provided with ice machine for sanitizing instructions.

Horizon, Horizon Elite, Maestro, Harmony, Ice Manager, SafeCLEAN, Sani-Sponge and Vision are trademarks of Follett LLC.
Chewblet, RIDE and Follett are registered trademarks of Follett LLC, registered in the US.

801 Church Lane • Easton, PA 18040, USA
Toll free [phone] • [phone]
www.follettice.com

01157908R01

© Follet LLC 1/18