Follett HCD1000NHS User Manual

Horizon™
Chewblet® ice icemaker

U.S. Patents
7,263,844, 7,469,548
and 7,469,552

HCD1400RBS shown

Short form specication

Icemaker to be a Follett® Horizon Chewblet ice icemaker model
HCD________________ [Insert size/series,condenser &
installation/mounting, from model number guide] without
remote condensing unit or with remote air-cooled condensing
unit, capable of producing compressed nugget ice using an
efficient, sanitary horizontal evaporator/auger system and
delivering ice by a exible wire reinforced, transport tube to
ice storage bin, ice and water dispenser, ice and beverage
dispenser, drop-in dispenser or Ice Manager™ diverter
valve system and provided with a stainless steel frame and
exterior, slide-out evaporator unit with utility docking station,
front-mounted unit status display, automatic self-ush, and
semi-automatic cleaning & sanitizing system, plus all the
features listed below and mounting/performance-enhancing
accessorieschecked:

Horizon performance features

• Produces popular Chewblet ice
(see Ice production tables on page 8):

1000 series - up to 900 pounds (409 kg) in 24 hours or
1400 series - up to 1333 pounds (605 kg) in 24 hours
Flexible tube ice-delivery-system allows Satellite-ll™ from up

to 75 ft (22.9 m) from bin/dispenser

• Horizontal evaporator maximizes iceproduction

• Uses less water than cube icemakers

• Rejects less heat than a typical cube icemaker

• Quiet operation without noisy batch harvest cycles

Unique Chewblet ice advantages

• Consumer-preferred chewable ice for beverages

• More reliable dispensing compared to nugget or pelletice

• Slow melting – maintains beverage temperature & quality

• Higher liquid displacement than cube ice

Key Horizon design features

• Compact design offers in-cabinet/undercounter, oor stand,
wall bracket, on-fountain dispenser, or on-bin mounting

• Stainless steel frame & exterior

• Standard slide-out docking-station design allows removal of
evaporator unit without disconnecting utilities

• Unique auger design reduces loads on gearmotor,
bearingsand seals

• Easy-to-read LED operating status & diagnostic display

• 10 ft (3 m) exible ice transport tube and insulation standard
with Satellite-ll models

• Uses environmentally-friendly R404A refrigerant

1000 series or 1400 series

with remote air-cooled condensing unit

(See model number guide)

Sanitation and safety features

• Aluminum-bronze evaporator has
antimicrobialproperties

• Automatic self-ushing reduces water scale buildup

• Floatless, sealed design inhibits formation of biolms

• Semi-automatic cleaning & sanitizing system

Agency approvals

Product warranty

• 3 years, parts & labor

• 5 years parts on compressor

Available accessories

Harmony™ conversion top kit for ice and beverage

dispensers (see page 3 for compatible ice and
beverage dispenser models and top kit numbers)

Water lter kit (Item# 00130286 - see form# 9905 for

dimensions)

___ ea. extra primary water lter cartridge
___ ea. extra pre-lter cartridge

Wall mount bracket (see accessory form# 3311)
Icemaker stand, height-adjustable

(see accessory form# 3311)

Longer ice transport tube, specify length: ___ ft/m in

5ft/1.5 m increments (10 ft/3 m is standard)

35 ft (10.7 m) refrigeration lines (P/N: 00193227 – not

pre-charged)

Model number guide

Use/

application

with ice
storage bins

with Follett
Vision™
line dispensers

with ice/
beverage
dispensers
(by others)

for drop-In
dispensers

with
Ice Manager
diverter
valve system

* Requires Harmony top kit (see page 3 for part number)

Installation/mounting

Condenser

top mounted Satellite-fill

with HCD1000RBT HCD1000RBS

without HCD1000NBT HCD1000NBS

with HCD1400RBT HCD1400RBS

without HCD1400NBT HCD1400NBS

with HCD1000RVS

without HCD1000NVS

with HCD1400RVS

without HCD1400NVS

with HCD1000RHT* HCD1000RHS

without HCD1000NHT* HCD1000NHS

with HCD1400RHT* HCD1400RHS

without HCD1400NHT* HCD1400NHS

with HCD1000RJS

without HCD1000NJS

with HCD1400RJS

without HCD1400NJS

with HCD1000RMS

without HCD1000NMS

with HCD1400RMS

without HCD1400NMS

Follett Corporation
801 Church Lane • Easton, PA 18040, USA
[phone] • Fax [phone]
www.follettice.com

Follett Europe Polska
Mokry Dwór 26C • 83-021 Wislina, Poland
[phone] • Fax [phone]
www.folletteurope.com

© Follett Corporation

Form# 3815

08/10

Horizon
Chewblet ice icemaker

Locating the icemaker

1

Horizon remote condensing unit Chewblet ice icemakers allow top-mounting or Satellite-ll ice-through-a-tube technology with
icemaker mounting in a base cabinet, on a wall or on a oor stand up to 75 ft (22.9 m) from the dispenser or ice bin. Evaporator/
icemaker must be mounted within 100 feet (30.5 m) of Follett remote condensing unit. Satellite-ll applications require special
attention to service access and ice tube runs (see page 3-5).

with remote air-cooled condensing unit

1000 series or 1400 series

Locating the icemaker

Top mounting – ice & beverage

dispensers (by others)

Satellite-fill – Follett low-profile

Vision ice & beverage dispensers

Top mount on

Follett ice storage bins

Important specifier notes: Important specifier notes: Important specifier notes:

1. Dispenser must be compatible with
nugget ice. See page 3 for compatible
ice & beverage dispenser models and
top kit numbers.

2. Verify ceiling or soffit height to ensure
sufficient top clearance.

Satellite-fill – ice & beverage dispensers

(by others)

1. See page 3-5 for critical clearance &
venting requirements.

Satellite-fill – drop-in beverage

dispensers (by others)

1. See form# B300 for bin sizing

2. Verify ceiling or soffit height to ensure
top clearance.

3. Locate oor sink or grate & drains in
front of storage bin.

4. Do not position bin drain lines to block
Ice•DevIce™ bin cart.

Satellite-fill for

Follett ice storage bins

Important specifier notes: Important specifier notes: Important specifier notes:

1. Dispenser must be compatible with
nugget ice. See page 3 for compatible
ice & beverage dispenser models.

2

Form# 3815

1. See form# 3425 for qualied
applications.

Follett Corporation
801 Church Lane • Easton, PA 18040, USA
[phone] • Fax [phone]
www.follettice.com

1. See form# B300 for bin sizing.

3. Locate oor sink or grate & drains in
front of storage bin.

4. Do not position bin drain lines to block
Ice•DevIce bin cart.

Follett Europe Polska
Mokry Dwór 26C • 83-021 Wislina, Poland
[phone] • Fax [phone]
www.folletteurope.com

Horizon

Ice transport tube

Chewblet ice icemaker

Locating the icemaker (continued)

1

Top mounting – compatible ice & beverage dispensers*

Width

Manufacturer Model Number

4500-30N 30.0 ( 76) 30.5 (78) 36.50 ( 93) HTL30RC-F

Lancer
dispensers

Cornelius
dispensers

SerVend
dispensers

*All approved dispensers can be filled with a Satellite-fill Horizon icemaker model without a top kit.

§ 60- inch models: Please specify number of Horizon icemakers and location. D = 2; R = 1 on right side; L = 1 on left side

† Requires minimum .5" (12.7 mm) clearance between back of dispenser and wall.
** Net height after installation of top kit (excluding height of icemaker).
# F-44N consists of 2 separate 22" dispensers. A top kit is needed for each Horizon icemaker ordered.

FS-22N 22.0 ( 56) 30.5 (78) 42.13 (107) HTL22RC-F

FS-30N 30.0 ( 76) 30.5 (78) 42.13 (107) HTL30RC- (F or B)

FS-44N # 44.0 (119) 30.5 (78) 42.13 (107) (2) HTL22RC-F

DB/ED/DF 200 series 30.0 ( 76) 30.0 (76) 34.38 ( 87) HTC30RC-F

DB/ED/DF 250 series 30.0 ( 76) 30.0 (76) 38.38 ( 98) HTC30RC-F

DB/ED/DF 300 series 44.0 (119) 30.0 (76) 34.00 ( 86) HTC44RC- (F or B)

FlavorFusion 30.0 ( 76) 30.7 (78) 39.38 (100) HTC30RC-10F-FF

IDC200 30.0 ( 76) 30.7 (78) 39.38 (100) HTC30RC-10F-IDC

IDC250 30.0 ( 76) 30.7 (78) 36.38 ( 92) HTC30RC-10F-IDC

MDH-302 42.8 (109) 31.0 (79) 32.38 ( 82) HTS44RC- (F or B)†

MDH-402 60.0 (152) 30.5 (78) 32.38 ( 82) HTS60RC- §(F or B)†

in (cm)

with remote air-cooled condensing unit

Depth
in (cm)

Height**
in (cm)

1000 series or 1400 series

Undercounter/in-cabinet mounting

Harmony top kit – specify “F” for front
facing, or “B” for backward facing units

HCD1000 & HCD1400 series

Undercounter/in-cabinet mounting

2

Important specifier notes

1. Cabinet door opening
must meet minimum size
requirements shown and
be free of obstructions to
allow icemaker to slide out
(no lip or utilities to block
removal).

2. Cabinet base must be
capable of supporting
icemaker and allow
icemaker to rest at on
cabinet bottom.

3. No counter supports,
electric or plumbing can
run in front of the icemaker.

4. Ice transport tube needs
minimum 1/4" per foot (2
cm per meter) pitch toward
icemaker and should be
secured to prevent dips and
traps from forming. See
page 4.

Cabinet details

minimum 1/4" per foot

Cabinet door
opening

21"W x 24.5"H
(53 cm x 62 cm)
minimum

(2 cm per meter)
pitch toward icemaker

secure to prevent dips
and traps from forming

Cabinet base

must be flat & free of obstructions
(no lip or utilities to block removal)

slides

out

12" (30 cm) minimum
between icemaker
and dispenser

electric

water

drain

see dispenser

specification

sheet for

installation

requirements

Follett Corporation
801 Church Lane • Easton, PA 18040, USA
[phone] • Fax [phone]
www.follettice.com

Follett Europe Polska
Mokry Dwór 26C • 83-021 Wislina, Poland
[phone] • Fax [phone]
www.folletteurope.com

Form# 3815

3