Follett HCC1010WVM, HCC1410WVM, HCC1010WMS, HCC1410AMS, HCC1010WPS User Guide
...
Horizon Elite™ 1010/1410 Ice Machines (Self-contained)
50 Hz and 60 Hz
User Guide
After Serial Number L60417
Please visit www.follettice.com/technicaldocuments
for the Operation and Service manual for your unit.
HCC/HMC 1010/1410 A/W
HCE/HME 1010/1410 A/W
Welcome to Follett
Follett equipment enjoys a well-deserved reputation for excellent performance, long-term reliability and outstanding
after-the-sale support. To ensure that this equipment delivers that same degree of service, review this guide
carefully before you begin your installation.
Should you need technical help, please call our Technical Service group at (877) 612-5086 or (610) 252-7301.
Please have your model number, serial number and complete and detailed explanation of the problem when
contacting Technical Service.
Getting Started
After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. All freight
is to be inspected upon delivery. If visible signs of damage exist, please refuse delivery or sign your delivery receipt
"damaged." Follett Customer Service must be notied within 48 hours. Wherever possible, please include detailed
photos of the damage with the original packaging so that we may start the freight claim process.
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
Installation and Service Videos:
www.follettice.com/servicevideolibrary
01266568R02
CAUTION!
§ Warranty does not cover exterior or outside installations.
§ Do not tilt unit further than 30° off vertical during uncrating or installation.
§ Dispenser bin area contains mechanical, moving parts. Keep hands and arms clear of this area at all times. If access to
this area is required, power to unit must be disconnected rst.
§ This appliance is not suitable for installation in an area where a water jet could be used.
§ This appliance must not be cleaned by a water jet.
§ User maintence should not be done by children.
§ Follett recommends a Follett water lter system be installed in the ice machine inlet water line (standard capacity
#00130229, high capacity #00978957, carbonless high capacity #01050442).
§ Prior to operation clean the dispenser in accordance with instructions found in this manual.
§ Do not block air intake or exhaust.
§ This appliance should be permanently connected by a qualied person in accordance with application codes.
§ A qualied person shall provide a readily accessible disconnect device incorporated into the xed wiring.
§ If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualied persons in
order to avoid a hazard.
§ This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory, or mental
capabilities, or lack of experience and knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children should be supervised to ensure that they do not
play with the appliance.
§ This appliance is designed for commercial use.
§ WARNING! To avoid a hazard due to instability of the appliance, it must be xed in accordance with the instructions.
§ Warranty does not cover exterior or outside installations.
§ To reduce risk of shock, disconnect power before servicing.
§ Connect to potable water supply only.
§ Ice is slippery. Maintain counters and oors around dispenser in a clean and ice-free condition.
§ Ice is food. Follow recommended cleaning instructions to maintain cleanliness of delivered ice.
Specications
Electrical
Each ice machine requires its own separate circuit with electrical disconnect within 10 ft (6 m).
Equipment ground required.
Standard electrical:
§ HCE1010: 230/50/1 (6 ft (2 m) cord) requires dedicated 15A circuit
§ HCE1410: 230/50/1 (6 ft (2 m) cord only, no plug) requires dedicated 20A circuit
§ HCC1010: 208-230/60/1 (6 ft (2 m) NEMA 6-15 cord and plug provided) requires dedicated 15A circuit
§ HCC1410: 208-230/60/1 (6 ft (2 m) NEMA 6-20 cord and plug provided) requires dedicated 20A circuit
§ Amperage: 1010A/W - 11A, 1410A/W - 14A
Plumbing
WARNING
This equipment to be installed with adequate backow protection to comply with applicable federal, state, and
local codes.
§ 3/8" OD push-in water inlet (connection inside machine) - 3/8" OD tubing required
§ 3/4" MPT drain
§ 1/4" FPT condenser inlet (water-cooled condenser only)
§ 1/4" FPT condenser drain (water-cooled condenser only)
Notes:
§ Water shut-off recommended within 10 feet (3 m).
§ Water supply must have particle ltration. Follett recommends the lter system that has integral scale inhibitors.
(Follett item# 00130286).
§ Follett does not recommend the use of water softeners or bowl scale inhibitors.
§ The potable water total dissolved solids (TDS) content must be greater than 10 ppm for the water control
system to function properly. If using reverse osmosis water ltration system, ensure TDS level is greater than
10ppm.
2 Horizon Elite 1010/1410 Self-Contained (50 Hz and 60 Hz)
Flush drain plumbing
3/4" barb x 3/4" FPT
1" Stand pipe/Drain
2 ft. x 1" OD
silicone tubing
Minimum 8"
radius
3/4" MPT x 1" slip
1" PVC Drain
2 ft. x 1" OD
silicone tubing
3/4" MPT x 1" slip
3/4" barb x 3/4" FPT
1'
1/4" per foot
(6,4 mm per 0,3 m)
§ 3/4" MPT ush drain connection at the rear of the machine.
§ Drain must slope 1/4" per foot (6 mm per 30.4 cm).
§ Drain line should not be shared with any other piece of equipment.
§ Drain line cannot be reduced to a size smaller than 1".
§ Drain should be piped without a vent.
Chassis drain plumbing
§ Plug must be removed from John Guest tting.
§ Route 3/8" drain tubing through knockout in back of docking station and insert fully into John Guest tting
connection at the rear of the machine chassis. Route other end of 3/8" drain tubing to drain.
§ Drain must slope 1/4" inch per foot (6 mm per 30.4 cm).
Horizon Elite 1010/1410 Self-Contained (50 Hz and 60 Hz) 3
Ambient
Air temperature 100 F/38 C max. 50 F/10 C min.
Water temperature 90 F/32 C max. 45 F/7 C min.
Water pressure – potable 70 psi max. (483 kPa) 10 psi min. (89 kPa)
Heat rejection
1010 1410
Air-cooled 11,300 BTU/hr 16,000 BTU/hr
Water-cooled 12,800 BTU/hr 16,400 BTU/hr
Weight
1010 1410
Approximate ship weight 275 lb (125 kg) 305 lb (138 kg)
Approximate net weight 265 lb (120 kg) 295 lb (134 kg)
Ice production
1010 Air-cooled ice machine capacity/24 hrs.
Ambient Air Temperature F/C
F 60 70 80 90 100
C 16 21 27 32 38
50 1160 1061 962 825 688 lbs
10 526 481 436 374 312 kg
60 1093 1001 909 795 681 lbs
16 496 454 412 361 309 kg
70 1026 941 857 765 674 lbs
21 465 427 389 345 306 kg
80 971 893 815 730 644 lbs
27 440 405 370 331 292 kg
90 917 845 773 694 614 lbs
Evap Potable Water Temperature F/C
32 416 383 351 315 279 kg
1410 Air-cooled ice machine capacity/24 hrs.
Ambient Air Temperature F/C
F 60 70 80 90 100
C 16 21 27 32 38
50 1593 1466 1339 1230 112 1 lbs
10 723 665 609 558 508 kg
60 1518 1396 1275 116 3 1052 lbs
16 689 633 578 528 477 kg
70 1442 1327 12 11 1097 982 lbs
21 654 602 549 498 445 kg
80 1394 1272 115 0 1050 950 lbs
27 632 577 522 476 431 kg
90 1345 1217 1089 1004 918 lbs
Evap Potable Water Temperature F/C
32 610 552 494 455 416 kg
1010 Water-cooled ice machine capacity/24 hrs.
Condenser Water Temperature F/C
F 50 60 70 80 90
C 10 16 21 27 32
50 1096 1043 1011 947 892 lbs
10 497 473 454 430 405 kg
60 1006 970 938 888 839 lbs
16 456 440 425 403 381 kg
70 917 898 8 74 830 778 lbs
21 416 407 396 376 353 kg
80 874 888 830 787 74 9 lbs
27 396 403 376 357 340 kg
90 831 807 778 74 5 712 lbs
32 377 366 353 338 323 kg
Evap Potable Water Temperature F/C
1410 Water-cooled ice machine capacity/24 hrs.
Condenser Water Temperature F/C
F 50 60 70 80 90
C 10 16 21 27 32
50 1393 1368 1343 1328 1313 lbs
10 632 621 609 602 596 kg
60 13 74 1326 1278 1268 1257 lbs
16 623 601 580 575 570 kg
70 1335 1284 1213 1207 1201 lbs
21 606 582 550 547 545 kg
80 1278 1216 11 5 3 113 5 1116 lbs
27 580 552 523 515 506 kg
90 1201 114 7 1093 1063 1032 lbs
32 545 520 496 482 468 kg
Evap Potable Water Temperature F/C
4 Horizon Elite 1010/1410 Self-Contained (50 Hz and 60 Hz)
Dimensions and clearances
§ Entire front of ice machine must be clear of obstructions/connections to allow removal.
§ 1" (26 mm) clearance above ice machine for service.
§ 1" (26 mm) minimum clearance on sides.
§ The intake and exhaust air grilles must provide at least 250 sq in (1615 sq cm) of open area.
§ Air-cooled ice machines – 18" (458 mm) minimum clearance between discharge and air intake-grilles.
1410 ONLY
1410 ONLY
A
C (1410 ONLY)
N
B
A 22.51" (57.2 cm)
D (1410 ONLY)
B 22.48" (57.1 cm)
C 25.15" (56.3 cm)
D 2.66" (6.8 cm)
E
G
F
E 20.84" (52.9 cm)
F 17.49" (44.4 cm)
G 15.00" (38.1 cm)
H 2.73" (6.9 cm)
I 2.30" (5.8 cm)
J 3.34" (8.5 cm)
H
I
J
K
L
M
K 10.44" (26.5 cm)
L 1.81" (4.6 cm)
M 28.50" (72.4 cm)
N 29.15" (74.0 cm)
Horizon Elite 1010/1410 Self-Contained (50 Hz and 60 Hz) 5
Loading...