Follett HCC1010ABS User Manual

Features

Horizon Elite

1010 series - up to 1061 pounds (482 kg) in 24 hours
1410 series - up to 1466 pounds (665 kg) in 24 hours

- automatically transport ice through a tube with
RIDE® technology from up to 75' (22.8 m) away

- chewable, compressed nugget ice is preferred
over cubes

1

- Chewblet ice dispenses reliably from ice and
beveragedispensers

- available with approximately 1.00" (2.54 cm) long
standard Chewblet ice or optional 3/8" (0.95 cm)
long Micro Chewblet

™

ice

- environmentally responsible R404a refrigerant with
zero ozonedepletion potential

- quiet production without noisy harvest cycles

Revolutionary, scale inhibiting design

- produces ice that has 15% the TDS of the incoming
water for optimum dispensing and long life in drinks

- quarantines and regularly expels scale producing
dissolved solids to dramatically reduce
scalebuildup

- increases time between descaling and reduces or
eliminates the need for expensive scale treatment

- saves 35% water compared to comparable cubers

- meets 2018 Department of Energy regulations

Durable, attractive ice machine

- regular bearing inspection or replacement is
notrequired

- upgraded, easy-to-read LED operating status and
diagnosticdisplay

Designed with sanitation in mind

- Agion® silver-based antimicrobial product protection
of key ice and water contact components

- floatless, sealed design inhibits formation
of biofilms

- semi-automatic cleaning and sanitizing system

Warranty

- 3 years parts and labor, 5 years compressor parts

Certifications

™

Horizon Elite

self-contained 1010, 1410 series Chewblet® ice machine

Short form specification:

Ice machine to be a Follett® Horizon Elite ice machine model ________________
[Insert size/series,condenser type and installation/mounting, from model
number guide] capable of producing compressed nugget ice using an ecient,
sanitary horizontal evaporator/auger system and delivering ice by a flexible wire
reinforced transport tube to
and beverage dispenser,
system, slide-out compressor/condenser/evaporator with utility docking station,
front-mounted unit status display, evaporator water inlet at harvest end with
automatic flush while producing ice, and semi-automatic cleaning and sanitizing
system, plusall the featureslisted below and mounting/performance-enhancing
accessories checked:

Horizon Elite self-contained 1010, 1410 series ice machine

Install/

For use with

ice storage
bin

Follett
Vision
dispenser

ice and
beverage
dispenser
(by others)

drop-in
dispenser
(by others)

Ice Manager
diverter
valve system

† ENERGY STAR® certified

1

Ordered separately

2

Requires Harmony™ top kit (see page 4 for part number)
NOTE: For Micro Chewblet ice, replace second character (C) with an M
e.g.HMC1010ABT

1

mount Condenser V/Hz/Ph 1010 series 1410 series

top
mount

RIDE

™

RIDE

top
mount

RIDE

RIDE

RIDE

Job
Item

ice storage bin, iceand water dispenser, ice

drop-in dispenser or Ice Manager™ diverter valve

air

water

air

water

air

water

air

2

water

air

water

air

water

air 220/60/1

water 220/60/1

220/60/1
230/50/1
220/60/1
230/50/1
220/60/1
230/50/1
220/60/1
230/50/1
220/60/1
230/50/1
220/60/1
230/50/1
220/60/1
230/50/1
220/60/1
230/50/1
220/60/1
230/50/1
220/60/1
230/50/1
220/60/1
230/50/1
220/60/1
230/50/1

HCC1010ABT† HCC1410ABT†
HCE1010ABT HCE1410ABT
HCC1010WBT HCC1410WBT
HCE1010WBT HCE1410WBT
HCC1010ABS† HCC1410ABS†
HCE1010ABS HCE1410ABS
HCC1010WBS HCC1410WBS
HCE1010WBS HCE1410WBS
HCC1010AVS† HCC1410AVS†
HCE1010AVS HCE1410AVS
HCC1010WVS HCC1410WVS
HCE1010WVS HCE1410WVS
HCC1010AHT†
HCE1010AHT HCE1410AHT
HCC1010WHT HCC1410WHT
HCE1010WHT HCE1410WHT
HCC1010AHS† HCC1410AHS†
HCE1010AHS HCE1410AHS
HCC1010WHS HCC1410WHS
HCE1010WHS HCE1410WHS
HCC1010AJS† HCC1410AJS†
HCE1010AJS HCE1410AJS
HCC1010WJS HCC1410WJS
HCE1010WJS HCE1410WJS

HCC1010AMS† HCC1410AMS†

HCC1010WMS HCC1410WMS

HCC1410AHT†

1 Independent third party studies. Contact Follett for details.
2 Disclaimer: Antimicrobial protection is limited to the treated components and does not treat water or ice.

801 Church Lane | Easton, PA 18040, USA

1.800.523.9361 | 1.610.252.7301 | follettice.com

Accessories

Harmony conversion top kit for ice and beverage

dispensers (listed onpage 4)

Water filter kit (item# 00978957– see form# 9905)

Dimensional drawing

D1

W1

____ ea. extra primary water filter cartridge
____ ea. extra pre-filter cartridge

Carbonless water filter kit (item# 01050442 –

see form# 6380)

Wall mount bracket (item# 01085455)
Ice machine stand, height-adjustable (item# 01085463)
Longer ice transport tube (10'/3 m is standard) –

Specify length: ____ft/m in 5'/1.5 m increments
(item#0017896

SafeCLEAN Plus

™

environmentally responsible ice

machine cleaner/sanitizer (item#01050863)

SaniSponge
Timer to control one or two 1010 and 1410 ice machines

™

, 24 sanitary sponges (item# 01075431)

(item# 00967265)

air

intake

for 1410 models only

H1

C1

20.84"

(52.9 cm)

17.49"

(44.4 cm)

(38.1 cm)

15.00"

2.73"

(6.93 cm)

3.34"

(8.48 cm)

C4

10.44"

(26.5 cm)

C2

C5

C3

2.30"

(5.84 cm)

12.25"

(31.1 cm)

C6C7

Specification

Horizon Elite 1010 series Horizon Elite 1410 series

W1 Width 29.15" (74.0 cm) 29.15" (74.0 cm)
D1 Depth 23.25" (59.1 cm) 25.15" (63.9 cm)
H1 Height 22.50" (57.2 cm) 22.50" (57.2 cm)

Clearance top, left and right–1.00"(2.54 cm) top, left and right–1.00"(2.54 cm)
Electrical

220 V/60/1 – HCC models
Electrical

230 V/50/1 – HCE models

C2 Ice transport tube see page 7 for details see page 7 for details
C3 Water inlet 3/8" OD push-in water inlet – internal connection 3/8" OD push-in water inlet – internal connection
C4 Drain 3/4" MPT 3/4" MPT
C5 Ice bin signal cord for Vision applications only for Vision applications only

Water-cooled ice machine
connections

Air temperature 50 -100 F (10 - 38 C) 50 -100 F (10 - 38 C)
Water temperature 45 - 90 F (7 - 32 C) 45 - 90 F (7 - 32 C)
Potable water pressure 10 - 70 psi (69 - 483 kPa) 10 - 70 psi (69 - 483 kPa)
Condenser water pressure 30 - 150 psi (207-1034 kPa) 30 - 150 psi (207-1034 kPa)
Ice production see ice production charts on page 8 see ice production charts on page 8
Energy consumption

90 F (32 C) air,
70 F (21C) water

Heat rejection air-cooled models – 11,300 BTU/hr

Water consumption 12.0 gal (45 L) of potable water per 100lb (45.4kg)

Water flow requirement for
water-cooled models

Approximate ship weight 275 lb (124 kg) 305 lb (138 kg)
NOTE: For indoor use only

C1 11 amps, requires dedicated 15 amp circuit,
6' (1.8 m) cord, NEMA 6-15 plug.

C1 11 amps, requires dedicated 15 amp circuit,
6' (1.8 m) cord only, no plug.

C6 – 1/4" FPT condenser inlet
C7 – 1/4" FPT condenser outlet

air-cooled models – 4.80 kWh
water-cooled models – 4.20 kWh
per 100lb(45.4 kg) ice

C1 14 amps, requires dedicated 20 amp circuit,
6'(1.8 m) cord, NEMA 6-20 plug.

C1 14 amps, requires dedicated 20 amp circuit,
6'(1.8 m) cord only, no plug.

C6 – 1/4" FPT condenser inlet
C7 – 1/4" FPT condenser outlet

air-cooled models – 4.84 kWh
water-cooled models – 3.80 kWh
per 100lb(45.4 kg) ice

air-cooled models – 16,000 BTU/hr

water-cooled models – 12,800 BTU/hr

water-cooled models – 16,400 BTU/hr

12.0 gal (45 L) of potable water per 100lb
ofice (per AHRI test standards) 12.4 gal (46.9 L) at
lowTDS flush setting

(45.4kg) of ice (per AHRI test standards) 12.3 gal
(46.5 L) at low TDS flush setting

1 gallon per minute 1gallon per minute

2

Form# 7030

Self-contained 1010, 1410 series ice machine

1 – Locating the ice machine

Horizon Elite self-contained Chewblet ice machines allow top-mounting or mounting in a base cabinet, on a wall or on a floor stand up
to 75' (22.8 m) from the dispenser or ice bin with RIDE technology. In-cabinet mounting (RIDE applications) require special attention to
service access, unit ventilation and ice tube runs (seepages 4-7).

Top mounting – ice and beverage
dispensers (by others)

RIDE model – Follett low-profile
Vision ice and beverage dispensers

Top mount on
Follett ice storage bins

Important specifier notes: Important specifier notes: Important specifier notes:

1. Dispenser must be compatible with
nugget ice. See page 4 for compatible ice
and beverage dispenser models and top
kit numbers.

2. Verify ceiling or soffit height to ensure
sufficient top clearance.

RIDE model – ice and beverage
dispensers (by others)

1. See page 4-6 for critical clearance and
venting requirements.

RIDE model – drop-in beverage
dispensers (by others)

1. See form# B300 for bin sizing.

2. Verify ceiling or soffit height to ensure top
clearance.

3. Locate floor sink or grate and drains in
front of storage bin.

4. Do not position bin drain lines to block
Ice•DevIce

™

bin cart.

RIDE model –
Follett ice storage bins

Important specifier notes: Important specifier notes: Important specifier notes:

1. Dispenser must be compatible with
nugget ice. Compatible dispensers include
Coca-Cola Freestyle 9000, Cornelius
DB/ID/DF150/175, Lancer 4500-22N,
FS-16N, FS-22N and FS-44N, Servend
MD150/175/200/250, SV175/200/250,

MDH-402 and FollettSymphony Plus
110CM, as well as dispensers listed on
page 4.

2. Top kit MSF30SC required with Coca-Cola
Freestyle 7000. Adapter 0002832 must
also be ordered from Coca-Cola.

3. See page 4-6 for critical clearance and
venting requirements.

4. RIDE application is approved only for Pepsi
Spire 3.0 and 5.0 designed for top mount
ice machines and requires MSP24SC
for 3.0 and MSP30SC for 5.0, ordered
separately. For manual fill versions of
PepsiSpire 3.0 and 5.0, contact factory.

1. Compatible with the following dispensers:
Cornelius 1522, 1722, 2323, and Lancer
2200, 2300, 23300.

2. Require 12.00" (30.5 cm) of access space
for installation on transport tubeside.

™

3. See page 4-6 for critical clearance and
venting requirements.

1. See form# B300 for bin sizing.

2. Locate floor sink or grate and drains in
front of storage bin.

3. Do not position bin drain lines to block
Ice•DevIce bin cart.

Self-contained 1010, 1410 series ice machine

Form# 7030

3