Follett HCC1000AVS Installation Manual

Horizon™ Icemaker Installation Instructions

for Vision™ Satellite- ll™ Applications

HCC1000AVS, HCC1400AVS, HCC1000WVS, HCC1400WVS,
HCE1000AVS, HCE1400AVS, HCE1000WVS, HCE1400WVS

(See model number con gurator on page 2 for details.)

Order parts online
www.follettice.com

self-contained

801 Church Lane • Easton, PA 18040, USA
Toll free [phone] • [phone]
www.follettice.com

a
i
n
a
v

l
y
s
n
n
e

P

O

n

N

o
t

T

s

R

E

a

L

A

E

P

G
IN
S

E
S
A
H
P

Z

O

HZ

O

N

N
L

IO

T

G

IA

I

A

S

R

R

P

E
S

O

E

RP

D

G

E

O

R

T

C

S

A

C

T

E

L

H

T

C

O

O

V

R

IN

P

E

E

D

D

Y

A

I

L

A

S

M

S

L

U

A

W

HE

L

M

O

T

E

R

L

D

HE

F

O

T

S

M

R

N

O
SS
E

S

R

P

P

M

U

LL

M

A

R

O

D

C

A

R

O

O

L

T

L

C

O

L

U

U

M

F

R

S
P
M

E

T

A

D

N

I

A

S

R

H

E

S

G

IG

P

I
R

H

F

AM

E

E

R

R

U
SS
E
R
P

Y
T
I

N

C
A
P

IG
S

M
A

E

T
I

D

U
C

E

IR

IZ

C

S

H

E
S

C

U

N

F

A
R

IT

B

U

.

C

IN

IR

M

C
H

C
N
A
R
B
.
X
A
M

208264

Stock Module Identification Plate
Module No.
Product

Service No.

00159921R04

Horizon Series Icemaker Model Number Configurations

A V SC 1400HC

Icemaker Voltage Series Condenser

HC Horizon
Chewblet
HM Horizon
MINI
Chewblet

† Ice Manager Diverter Valve Systems can be used to fill any two of these bins or dispensers with a single ice machine.

C 208-230/60/1

(self-contained only)

D Low side 115/60/1
Condensing unit
208-230/60/1

(remote condensing only)

E 230/50/1

(self-contained only)

1000 up to
1036 lbs
(471kg)

1400 up to
1450 lbs
(658kg)

A Air-cooled, self-contained
W Water-cooled, self-contained
R Air-cooled, remote condensing unit
N Air-cooled, no condensing unit for
connection to parallel rack system

Application Configuration

V Vision™
H Harmony™
B Ice storage
bin
J Drop-in
M Ice Manager
diverter valve
system

S Satellite-fill™
T Top-mount

†

2

self-contained VISION • SATELLITE-FILL

Read and complete the following 8 installation steps

Unpack

1

Dispenser preparation

3

Ice transport tube

5

Site preparation

2

Louvered docking assembly

4

External connection

6

Internal connection

7

Front cover

8

VISION • SATELLITE-FILL self-contained

3

Carefully unpack and inspect the contents of your Follett icemaker.

1/2"

1/2"

➊➋

➌➍

➎➏

Unpack

1

1. 1

Unpack icemaker

4

self-contained VISION • SATELLITE-FILL

Site preparation

Prepare the installation site.

Provide drainage, water supply and electrical power to within 6 feet (2m) of
icemaker in accordance with local and national codes. Outdoor installation is
not recommended and will void warranty.

2

2.1

2.1

Installation site requirements

1/4"

1'

➍

➊

➋

➌

➍

HCE1000A/W

requires 15 amp circuit

HCE1400A/W

requires 20 amp circuit

HCC1000A/W

NEMA

6-15

HCC1400A/W

NEMA

6-20

‡

1.50 mm2 wire

‡

4.00 mm2 wire

Electrical

➊

• HCC1000(A/W)VS 208-230/60/1-15 amps • HCC1400(A/W)VS 208-230/60/1-20 amps

• HCE1000(A/W)VS 230/50/1-15 amps

(HCE1000A/W Requires 15 amp circuit 1.50 mm2 wire) (HCE1400A/W Requires 20 amp circuit 4.00 mm2 wire)

‡ Plug must be provided by end user & must conform to standard EN 60 335-2-24 of the end destination.

Potable water supply

➋

‡

• HCE1400(A/W)VS 230/50/1-20 amps

• 10-70 psi (69-483kpa)

• 45 to 90 F (7 to 32 C)

• Follett recommends the use of an in-line water filtration system (item# 00130286)

Condenser water supply for water-cooled systems

➌

• 10 psi min.; 150 psi max. (69kpa min.; 1034kpa max.)

• 45 to 90 F (7 to 32 C)

• 1.5 gallons per minute (5.68 liters per minute)

Drain

➍

• The drain line from the icemaker must have at least 1/4" per foot pitch (6,4mm/0,3m)

VISION • SATELLITE-FILL self-contained

‡

5

Prepare the dispenser.

Dispenser preparation

3

2.1

3.1

Bin Signal Installation

➏

➎

➏

24"

(610 mm)

➌

➍

➋

Ground

➊

➌

• Mount the electrical box to the side of the Vision dispenser ➊ to establish a ground
connection.
Note: If a 4 x 4 box is mounted to a non-grounded surface, connect ground wire at an
appropriate ground.

• Connect the bin signal plug on the electrical box to the bin signal cord on the bin

• Insert 24" (609,6mm) of the long bin signal cable ➌ into the hole in the back of the louvered
docking station

• After sliding the icemaker module into the louvered docking station, disconnect the shuttle
plug

• Complete normal installation procedure for the icemaker using the installation manual that
shipped with the icemaker.

• Connect the bin signal plug

6

from the icemaker control box.

➎

and secure in place with strain relief provided.

➍

into the icemaker control box.

➏

self-contained VISION • SATELLITE-FILL

➋