Follett HCC1000ABS User Manual
Horizon™
Chewblet® ice icemaker
U.S. Patents
7,263,844, 7,469,548
and 7,469,552
HCC1400WBS shown
Short form specication
Icemaker to be a Follett® Horizon Chewblet ice icemaker model
HCC________________ [Insert size/series,condenser type
& installation/mounting, from model number guide] capable of
producing compressed nugget ice using an efficient, sanitary
horizontal evaporator/auger system and delivered by a exible
wire reinforced, FDA-approved transport tube to: ice storage
bin, ice and water dispenser, ice and beverage dispenser,
drop-in dispenser or Ice Manager™ diverter valve system
and provided with a stainless steel frame and exterior, slide-out
compressor/condenser with utility docking station, front-mounted
unit status display, automatic self-ush, and semi-automatic
cleaning & sanitizing system, plus all the features listed below
and mounting/performance-enhancing accessorieschecked:
Horizon performance features
• Produces popular Chewblet ice
(see Ice production tables on page 8):
1000 series - up to 1125 pounds (511 kg) in 24 hours or
1400 series - up to 1450 pounds (658 kg) in 24 hours
Flexible tube ice-delivery-system allows Satellite-ll™ from up
to 75 ft (22.9 m) from bin/dispenser
• Horizontal evaporator maximizes heat transfer &
iceproduction
• Uses less water than cube icemakers
• Rejects less heat than a typical cube icemaker
• Quiet operation without noisy batch harvest cycles
Unique Chewblet ice advantages
• Consumer-preferred chewable ice for beverages
• More reliable dispensing compared to nugget or pelletice
• Slow melting – maintains beverage temperature & quality
• Higher liquid displacement than cube ice
Key Horizon design features
• Compact design offers in-cabinet/undercounter, oor stand,
wall bracket, on-fountain dispenser, or on-bin mounting
• Stainless steel frame & exterior
• Standard slide-out docking-station design allows removal of
compressor/condenser without disconnecting utilities
• Unique auger design reduces loads on gearmotor,
bearingsand seals
• Easy-to-read LED operating status & diagnostic display
• 10 ft (3 m) exible ice transport tube and insulation standard
with Satellite-ll models
1000 series or 1400 series
air-cooled or water-cooled
(See model number guide)
Sanitation & safety features
• Uses environmentally-friendly R404A refrigerant
• Aluminum-bronze evaporator has
antimicrobialproperties
• Automatic self-ushing reduces water scale buildup
• Floatless, sealed design inhibits formation of biolms
• Semi-automatic cleaning & sanitizing system
Agency approvals
Product warranty
• 3 years, parts & labor
• 5 years parts on compressor
Available accessories
Harmony™ conversion top kit for ice and beverage
dispensers (see page 3 for compatible ice & beverage
dispenser models and top kit numbers)
Water lter kit (Item# 00130286 - see form# 9905 for
dimensions)
___ ea. extra primary water lter cartridge
___ ea. extra pre-lter cartridge
Wall mount bracket (see accessory form# 3311)
Icemaker stand, height-adjustable
(see accessory form# 3311)
Longer ice transport tube, specify length: ___ ft/m in
5ft/1.5 m increments (10 ft/3 m is standard)
Model number guide
Use/
application
with ice
storage bins
with Follett
Vision™ line
dispensers
with ice/
beverage
dispensers
(by others)
for drop-In
dispensers
with
Ice Manager
diverter valve
system
* Requires Harmony top kit (see page 3 for part number)
Condenser
type
air-cooled
water-cooled
air-cooled
water-cooled
air-cooled
water-cooled
air-cooled
water-cooled
air-cooled
water-cooled
Installation/mounting
top mounted Satellite-fill
HCC1000ABT
HCC1400ABT
HCC1000WBT
HCC1400WBT
HCC1000AHT*
HCC1400AHT*
HCC1000WHT*
HCC1400WHT*
HCC1000ABS
HCC1400ABS
HCC1000WBS
HCC1400WBS
HCC1000AVS
HCC1400AVS
HCC1000WVS
HCC1400WVS
HCC1000AHS
HCC1400AHS
HCC1000WHS
HCC1400WHS
HCC1000AJS
HCC1400AJS
HCC1000WJS
HCC1400WJS
HCC1000AMS
HCC1400AMS
HCC1000WMS
HCC1400WMS
801 Church Lane • Easton, PA 18040, USA
Toll free (800) 523-9361 • (610) 252-7301
Fax (610) 250-0696 • www.follettice.com
© Follett Corporation
Form# 3810
06/10
Horizon
Chewblet ice icemaker
Locating the icemaker
1
Horizon self-contained Chewblet ice icemakers allow top-mounting or Satellite-ll ice through a tube technology with icemaker
mounting in a base cabinet, on a wall or on a oor stand up to 75 ft (22.9 m) from the dispenser or ice bin. In-cabinet mounting
and Satellite-ll applications require special attention to service access, unit ventilation and ice tube runs (see page 3-5).
1000 series or 1400 series
air-cooled or water-cooled
Locating the icemaker
Top mounting – ice & beverage
dispensers (by others)
Satellite-fill – Follett low-profile
Vision dispensers
Top mount on
Follett ice storage bins
Important specifier notes: Important specifier notes: Important specifier notes:
1. Dispenser must be compatible with
nugget ice. See page 3 for compatible
ice & beverage dispenser models and
top kit numbers.
2. Verify ceiling or soffit height to ensure
sufficient top clearance.
1. See page 3-5 for critical clearance &
venting requirements.
1. See form# B300 for bin sizing
2. Verify ceiling or soffit height to ensure
top clearance.
3. Locate oor sink or grate & drains in
front of storage bin.
4. Do not position bin drain lines to block
Ice•DevIce™ bin cart.
Satellite-fill – ice & beverage dispensers
(by others)
Satellite-fill – drop-in beverage
dispensers (by others)
Satellite-fill for
Follett ice storage bins
Important specifier notes: Important specifier notes: Important specifier notes:
1. Dispenser must be compatible with
nugget ice. See page 3 for compatible
ice & beverage dispenser models and
top kit numbers.
2
Form# 3810
1. See form# 3425 for qualied
applications.
1. See form# B300 for bin sizing.
2. Locate oor sink or grate & drains in
front of storage bin.
3. Do not position bin drain lines to block
Ice•DevIce bin cart.
801 Church Lane • Easton, PA 18040, USA
Toll free (800) 523-9361 • (610) 252-7301
Fax (610) 250-0696 • www.follettice.com
Horizon
Chewblet ice icemaker
Locating the icemaker (continued)
1
Top mounting – compatible ice & beverage dispensers*
Width
Manufacturer Model Number
4500-22N 22.0 ( 56) 30.5 (78) N/A Satellite-fill only
Lancer
dispensers
Remcor/Cornelius
dispensers
SerVend
dispensers
*All approved dispensers can be filled with a Satellite-fill Horizon icemaker model without a top kit.
† Requires minimum .5" (12.7 mm) clearance between back of dispenser and wall.
** Net height after installation of top kit (excluding height of icemaker).
# F-44N consists of 2 separate 22" dispensers. A top kit is needed for each Horizon icemaker ordered.
4500-30N 30.0 ( 76) 30.5 (78) 36.50 ( 93) HTL30SC-10F
FS-22N 22.0 ( 56) 30.5 (78) 42.13 (107) Satellite-fill only
FS-30N 30.0 ( 76) 30.5 (78) 42.13 (107) HTL30SC-10F
FS-44N # 44.0 (119) 30.5 (78) 42.13 (107) Satellite-fill only
4500-22N 22.0 ( 56) 30.5 (78) N/A Satellite-fill only
DB/ED/DF 200 series 30.0 ( 76) 30.0 (76) 34.38 ( 87) HTC30SC-10F
DB/ED/DF 250 series 30.0 ( 76) 30.0 (76) 38.38 ( 98) HTC30SC-10F
DB/ED/DF 300 series 44.0 (119) 30.0 (76) 34.00 ( 86) HTC44SC-10 (F or B)
FlavorFusion 30.0 ( 76) 30.7 (78) 39.38 (100) HTC30SC-10F-FF
IDC200 30.0 ( 76) 30.7 (78) 39.38 (100) HTC30SC-10F-IDC
IDC250 30.0 ( 76) 30.7 (78) 36.38 ( 92) HTC30SC-10F-IDC
MDH-302 42.8 (109) 31.0 (79) 32.38 ( 82) HTS44SC-10 (F or B)†
MDH-402 60.0 (152) 30.5 (78) 32.38 ( 82) Satellite-fill only
in (cm)
Depth
in (cm)
1000 series or 1400 series
air-cooled or water-cooled
Undercounter/in-cabinet mounting
Harmony top kit – specify “F” for front
Height**
in (cm)
facing, or “B” for backward facing units
HCC1000 series – air or water
Undercounter/in-cabinet mounting
2
Important specifier notes
1. Cabinet door opening
must meet minimum size
requirements shown and
be free of obstructions to
allow icemaker to slide out
(no lip or utilities to block
Cabinet door opening
1000 series models require
28.6"W x 24.5"H (73 cm x 62 cm) minimum,
40"W (102 cm) minimum for centered air intake grille
1400 series models require
31.6"W x 24.5"H (80 cm x 62 cm) minimum,
46"W (117 cm) minimum for centered air intake grille
removal).
2. Cabinet base must be
capable of supporting
icemaker and allow
icemaker to rest at on
cabinet bottom.
3. No counter supports,
electric or plumbing can
run in front of the icemaker.
Cabinet details
slides
out
Cabinet base
must be flat & free of obstructions
(no lip or utilities to block removal)
801 Church Lane • Easton, PA 18040, USA
Toll free (800) 523-9361 • (610) 252-7301
Fax (610) 250-0696 • www.follettice.com
Form# 3810
3
Loading...