Follett FZR5 Parts List

FZR Series

Undercounter Freezer

Order parts online
www.follettice.com

Installation, Operation and Service Manual

Following installation, please forward this manual

to the appropriate operations person.

801 Church Lane • Easton, PA 18040, USA
Toll free [phone] • [phone]
Fax [phone] • www.follettice.com

00156216R03

Welcome to Follett

Follett equipment enjoys a well-deserved reputation for excellent performance, long-term reliability and
outstanding after-the-sale support. To ensure that this product delivers that same degree of service, we ask that
you take a moment to review this manual before beginning the installation. Should you have any questions or
require technical help at any point, please call our technical service group at [phone] or [phone].

Before you begin

After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If
damage is found, notify the shipper immediately and contact Follett Corporation so that we can help in the filing
of a claim, if necessary.

Specifications

Series specifications

FZR5

34.00" height for freestanding use or installation below standard 36" (915mm) high counter

4.0 cu ft (usable cubic volume)

FZR4-ADA

31.25" height for freestanding use or installation below 34" (864mm) high ADA-compatible counter

3.3 cu ft (usable cubic volume)

Electrical specifications

115V, 60Hz, 1 phase

Full load amps: 8.0

Minimum circuit ampacity: 15 amp

Maximum size of branch circuit overcurrent device: 15 amp

Refrigeration specifications

Refrigerant – R404A

Charge size – 10 oz

Maximum design pressures:

High side – 383psi
Low side – 175psi

Installation specifications

Ambient temperature must not exceed 100°F (38°C).

The front louvered panel must be kept free of any cabinet trim or obstructions to ensure proper ventilation of the
refrigeration system.

Important cautions

• Equipment must be wired according to local and NEC codes.

• Always disconnect power before servicing freezer.

2

Installation

Installing legs – required

1. Remove legs from plastic bag packed inside freezer.

2. Tip freezer back and screw legs in all the way to stop (they will extend
1/8" below base of freezer).

3. Adjust legs as needed to level freezer in both directions. To access
legs, remove the lower front panel. Turn legs clockwise to extend legs.

Installing shelves – required

1. Remove shelves and shelf brackets packed inside freezer.

2. Install shelf brackets in pilasters (insert top tab, squeeze and push in
lower tab).

Fig. 1

Fig. 2

2

1

3

Installing controller faceplate – required

The freezer is shipped from the factory configured to display in °C. If °F
display is desired, resetting of temperature controller is required. Contact
factory for re-programming key.

1. Remove °F and °C faceplates from plastic bag packed inside
refrigerator.

2. Snap appropriate faceplate in place over controller face.

Changing temperature controller settings – optional

Follett’s temperature controller is pre-programmed with a -25°C (-13°F) set
point and °C display. The -25°C (-13°F) set point delivers a temperature
range of -23° to -25°C (-9 to -13°F). Follett’s controller set point can be
changed to deliver up to a -15°C (5°F) temperature for applications where
a lower temperature is not desired (i.e. ice cream). See page 5 to change
controller settings.

Fig. 3

Fig. 4

3

Reversing the door swing – optional

1. Remove screws and latch from freezer cabinet. (Fig. 5.1).

2. Use flat screwdriver to carefully remove (do not scratch) hinge
covers (Fig. 6.1).

3. Support door and remove screws attaching hinge to freezer cabinet
(Fig. 6.2).

4. Cover hinge screw holes with screw hole plugs removed from
opposite side.

5. Reverse door and reinstall hinge screws.

6. Reinstall latch on opposite side.

7. Remove screws and handle from door (Fig. 7.1).

8. Rotate handle (Fig. 7.2).

9. Reinstall handle screws (application of 242 blue Loctite
handle screws recommended).

®

to

Fig. 5

1

2

Fig. 6

Fig. 7

2

1

1

1

2

Loctite is a registered trademark of Henkel Corporation in the United States and other countries.

4

Controller operation

In normal operation the controller displays cabinet temperatures in
°C (default) or user-selected °F. °C temperatures are displayed to 1
decimal point.

Fig. 8

evaporator
fan
energized

defrost

refrigeration
system
energized

Rocker buttons to the right of the temperature display control all
programming functions.

- 25

The controller is pre-programmed with a -25°C (-13°F) set point
which provides a compressor cut-in at -23° (-9°F) and cut-out at

-25°C (-13°F). The controller set point can be raised to -15°C (5°F)

for nourishment applications where a lower temperature is not
desired (i.e. ice cream). Follow instructions for changing temperature
cut-out below.

All set points have a 2°C differential. The 2°C differential means that with a -25°C set point, for example, the
compressor will turn off at -25°C (-13°F) and turn on when it reaches -23° (-9°F).

not used

°C

prg

SET

To display temperature cut-out

STEP INPUT DISPLAY

1 Press and release SET Current cut-out temperature will display for approximately 5 seconds.
Display will return to current freezer temperature.

To change temperature cut-out

STEP INPUT DISPLAY

1 Press and hold SET for 3 Current cut-out temperature seconds displayed

2 Press UP or DOWN arrows to New cut-out temperature displayed
desired cut-out temperature

3 Press and release SET New cut-out temperature blinks three times, then current freezer
temperature will display

To change temperature display from °C to °F

Follett provides a programming key (part# 00155630) that changes the display and temperature settings from
°C to °F. Contact Follett at [phone] if this key is required.

5