English
Operator's manual
Operator's Manual
Please read the operatorsmanual carefully and make sure you understand the instructions
before using the machine.
Contents
Introduction
Language.............................................................. 3
Introduction............................................................3
Intended use..........................................................3
Product overview...................................................4
Safety
Symbols on the product.........................................5
General safety instructions....................................5
Additional safety instructions.................................7
Assembly
Before you do assembly........................................8
To assemble the bumper and the lower handle.... 8
To assemble the middle handle............................ 8
To assemble the upper handle..............................9
To assemble the grass box................................... 9
To assemble the grass box lid.............................10
Operation
Before you do operation...................................... 10
To connect the mower.........................................10
To start the mower.............................................. 10
To adjust the cutting height................................. 11
To use the mower with the grass box..................11
To use the mower without the grass box.............11
Tips to use the mower......................................... 11
Maintenance
Before you do maintenance................................ 12
To clean the product:...........................................12
To clean the underside of the product:................12
To clean the overside of the product and
the grass box:......................................................12
Storage
To put into storage:............................................. 12
Disposal (in accordance with RL2012/19/EC):....12
Troubleshooting
Before you do troubleshooting............................ 13
To clean the bumper........................................... 13
To replace the blade............................................13
Troubleshooting table..........................................13
Repairs................................................................ 14
Technical data
Electric Lawnmower............................................ 14
EC Declaration of Conformity..............................15
Accessories
For Electric Lawnmower......................................15
Service / Warranty
Service................................................................ 16
Warranty..............................................................16
Consumable........................................................ 16
Product liability.................................................... 16
2 17 - 001 -
Introduction
Language
The initial language of these instructions is English.
Other language versions are translations of the initial
instructions.
Introduction
This product may be used
under supervision, or if
instruction regarding the safe
use of the product has been
provided and the resulting
dangers have been
understood, by children aged
8 and above, as well as by
persons with physical, sensory
or mental disabilities or a lack
of experience and knowledge.
Children must not be allowed
to play with the product.
Cleaning and user
maintenance must not be
performed by children without
supervision.
The use of this product by
young people under the age of
16 is not recommended.
Intended use
The FLYMO Electric Lawnmower is used to cut lawn
in private domestic gardens and allotments.
The product is not intended for long term use.
WARNING!
• Risk of injury!
• Do not use the product to cut
bushes, hedges, shrubs, to cut of
climbers or grass on roofs or balcony
boxes, to chop up branches, twigs
and to level irregularities in the soil.
Do not use the product on a slope
steeper than 20° maximum.
17 - 001 - 3
Product overview
17
2
3
1
4
14
15
16
5
2 x
6
2 x
7
3 x
8
4 x
18
13
12
11
10
9
19
1. Push button
2. Wing knob
3. Cable hook knob
4. Cable hook pin
5. Bolt
6. Washer (2 x)
7. Cable clip (3 x)
8. R-clip (4 x)
9. Lower handle
10. Mower body
11. Grass box chute
12. Grass box lid
13. Grass box cover
14. Grass box handle
15. Upper handle
16. Middle handle
17. Bumper
18. Cable connector
19. Grass box
4 17 - 001 -
Safety
Symbols on the product
CAUTION!
If not used properly this product can be
dangerous. The warnings and safety
instructions must be followed to ensure
reasonable safety and efficiency in using
this product. The operator is responsible
for following the warnings and
instructions in this manual and on the
product. Never use the product unless
the guards provided by the manufacturer
are in the correct position.Careless or
incorrect use of this product can result in
injury to the user or others. Read and
understand the content of the operator's
manual. Keep the manual for future
reference.
Read the instructions.
Keep other persons
away.
Beware of sharp
blades. Blades continue
to rotate after the engine is switched off.
Disconnect the mains
cable before you do
maintenance or if the
cable becomes damaged or cut.
Keep the mains cable
away from the cutting
blades.
General safety instructions
Electrical safety
WARNING!
• Electric shock !
• Risk of injury due to electric shock.
• The product must be supplied
through a residual current device
(RCD) having a rated residual
operating current not exceeding 30
mA.
WARNING!
• Electric shock!
• Risk of injury due to electric shock.
• Disconnect the product from the
mains before you do maintenance or
you replace parts. Thereby the
disconnected socket must be in the
visual range.
Cables
If extension cables are used, these must comply with
the minimum cross-sections in the table below:
Voltage
Cable length
Cross section
220 - 240 V / 50 Hz Up to 40 m 1.0 mm
2
220 - 240 V / 50 Hz Up to 60 m 1.5 mm
2
220 - 240 V / 50 Hz Max. 100 m 2.5 mm
2
Minimum rating: 1.0 mm2 size cable, 10 amps 250
volts AC.
Your product is supplied with cable wired directly into
the product.
1. If the supply cord is damaged, it must be
replaced by your local Husqvarna UK Ltd.
Approved Service Centre or similarly qualified
persons in order to avoid a hazard.
2. Flymo Extension Cables are available from your
local Husqvarna UK Ltd. Approved Service
Centre.
3. Do not wire an extension cable directly to your
product yourself. Please contact your local
Husqvarna UK Ltd. Approved Service Centre for
further information on the connectors and kits
available.
4. Only use extension cables specifically designed
for outdoor use and which conform to one of the
following specifications: Ordinary rubber (60245
IEC 53), Ordinary PVC (60227 IEC 53) or
Ordinary PCP (60245 IEC 57)
Connectors - Important
• Flymo connectors are suitable for use with 2 core
cable only. Under no circumstances should these
connectors be used for earthed products.
• All Flymo connectors and cables are of
splashproof construction. They are not
waterproof and must not be left outside
permanently nor should they be submerged or
immersed in water. Do not let cable lay or trail
through pools of water or splashed with water
from hose pipes.
17 - 001 -
5
Mains plug replacement - Important
• If the plug supplied is cut off it should be
destroyed. There is an electric shock hazard if a
cut off plug is inserted into a 13 amp socket.
1. No earth required. Flymo products are double
insulated to EN60335 and under no
circumstances should an earth be connected to
any part of the product.
2. Ensure the mains voltage suits your product.
3. Important!The wires in the mains lead are
coloured in accordance with the following code:
BLUE - NEUTRAL ; BROWN - LIVE. The wire
which is coloured BLUE must be connected to
the Terminal which is marked with the letter 'N' or
coloured BLACK. The wire which is coloured
BROWN must be connected to the Terminal
which is marked with the letter 'L' or coloured
RED.
4. It is important that the outer sheath is clamped
correctly into the 3-pin plug.
5. If in doubt consult your local Service Repairer or
qualified electrician before the machine is used.
6. A 13 Amp fuse must be fitted to the Mains Plug.
7. The normal plug fuse and household fuse only
protect the electrical equipment and are not a
safeguard against electrocution.
Training
1. Read the instructions carefully. Be familiar with
the controls and the correct use of the machine.
2. Never allow children or people unfamiliar with
these instructions to use the machine. Local
regulations can restrict the age of the operator.
3. Never operate the machine while people,
especially children, or pets are nearby.
4. Keep in mind that the operator or user is
responsible for accidents or hazards occurring to
other people or their property.
Preparation
1. While operating the machine always wear
substantial footwear and long trousers. Do not
operate the machine when barefoot or wearing
open sandals. Avoid wearing clothing that is
loose fitting or that hanging cords or ties.
2. Thoroughly inspect the area where the machine
is to be used and remove all objects which can
be thrown by the machine.
3. Before using, always visually inspect to see that
the blade, blade bolt and the blade assembly are
not worn or damaged. Replace worn or damaged
components in set to preserve balance. Replace
damaged or unreadable labels.
4. Before use check the supply and extension cord
for signs of damage or aging. If the cord
becomes damaged during use, disconnect the
cord from the supply immediately. DO NOT
TOUCH THE CORD BEFORE
DISCONNECTING THE SUPPLY. Do not use
the machine if the cord is damaged or worn.
Operation
1. Operate the machine only in daylight or in good
artificial light.
2. Avoid operating the machine in wet grass.
3. Always be sure of your footing on slopes.
4. Walk, never run.
5. Mow across the face of slopes, never up and
down.
6. Exercise extreme caution when changing
direction on slopes.
7. Do not mow excessively steep slopes.
8. Use extreme caution when reversing or pulling
the machine towards you.
9. Stop the blade(s) if the machine has to be tilted
for transportation when crossing surfaces other
than grass, and when transporting the machine
to and from area to be used.
10. Never operate the machine with defective guards
or shields, or without safety devices, for example
deflectors and/or grass collector, in place.
11. Switch on the motor carefully according to
instructions and with feet well away from the
blade(s).
12. Do not tilt the machine when switching on the
motor, except if the machine has to be tilted for
starting. In this case, do not tilt it more than
absolutely necessary and lift only the part, which
is away from the operator.
13. Do not start the machine when standing in front
of the discharge opening.
14. Do not put hands or feet near or under rotating
parts. Keep clear of the discharge opening at all
times.
15. Do not transport the machine while the power
source is running.
16. Stop the machine, and remove the plug from the
socket. Make sure that all moving parts have
come to a complete stop
• whenever you leave the machine,
• before clearing blockages or unclogging
chute,
• before checking, cleaning or working on the
machine,
• after striking a foreign object. Inspect the
machine for damage and make repairs before
restarting and operating the machine;
if the machine starts to vibrate abnormally (check
immediately)
• inspect for damage,
• replace or repair any damaged parts,
• check for and tighten any loose parts.
6
17 - 001 -
Maintenance and storage
1. Keep all nuts, bolts, and screws tight to be sure
the machine is in safe working condition.
2. Check the grass collector frequently for wear or
deterioration.
3. On machines with multi blade, take care as
rotating one blade can cause other blades rotate.
4. Be careful during adjustment of the machine to
prevent entrapment of the fingers between
moving blades and fixed parts of the machine.
5. Always allow the machine to cool down before
storing.
6. When servicing the blades be aware that, even
though the power source is switched off, the
blades can still be moved.
7. Replace worn or damaged parts for safety. Use
only genuine replacement parts and accessories.
Additional safety instructions
Electrical safety
WARNING!
• Cardiac arrest!
• This product makes an
electromagnetic field while it
operates. This field may under some
conditions interfere with active or
passive medical implants.
• To decrease the risk of conditions
that can possibly injure or kill, we
recommend persons with medical
implants to speak with their physician
and the medical implant
manufacturer before you operate the
product.
Before use, examine the cable for signs of damage
or ageing. If the cable is found to be defective, take
the product to an Authorised Service Centre and
have the cable replaced.
Do not use the product if the electric cables are
damaged or worn.
Immediately disconnect from the mains if the cable is
cut, or the insulation is damaged. Do not touch the
electric cable until the cable has been disconnected.
Do not repair a cut or damaged cable. Replace it
with a new one.
The extension cable must be uncoiled. Coiled cables
can overheat and reduce the efficiency of your
mower.
Keep the extension cable away from product, always
work away from the power point mowing up and
down, never in circles.
Do not pull cable around sharp objects.
Always switch off at the mains before disconnecting
any plug, cable connector or extension cable.
Stop the engine, disconnect the mains and examine
the cable for damage or ageing before you wind the
cable for storage. Do not repair a damaged cable,
replace it with a new one. Use only genuine
replacement cable.
Always wind the cable carefully, avoid kinking.
Do not carry the product by the cable.
Do not pull on the cable to disconnect any of the
plugs.
Use only on AC mains supply voltage shown on the
product rating label.
Our products are double insulated to EN60335. Do
not connect an earth to any part of the product.
Check the working area for hidden cables.
Do not use for pond care or close to water.
Personal safety
WARNING!
• Risk of suffocation
• Small parts can be easily swallowed.
There is also a risk that the polybag
can suffocate toddlers.
• Keep toddlers away when you
assemble the product.
Do not use in explosive atmosphere.
Do not operate the product when you are tired, ill or
under the influence of alcohol, drugs or medicine or
you exhaustid.
Do not overload the mower.
Use gloves, wear slip resistant shoes and wear eye
protection.
Do not use under wet conditions.
Do not use on wet grass.
Do not disassemble the product further than the
delivery status.
Only start the mower with an upright standed handle.
Do not use the start levers alternately.
Use the handles carefully.
Safety Cut-Out
The engine is protected by a Safety Cut-Out which is
activated when the blade becomes jammed or if the
engine is overloaded. When this occurs, stop and
disconnect the product from the mains. The Safety
Cut-Out will only reset when you release the start/
stop lever. Clear any obstruction and wait for a few
minutes for the Safety Cut-Out to reset before you
continue to use the product.
17 - 001 -
7
Assembly
Before you do assembly
WARNING!
• Risk of physical injury!
• Cut injury when the blade turns or
the product starts accidentally.
• Wait for the blade to stop, disconnect
the product from the mains and use
gloves before you do assembly.
To assemble the bumper and the
lower handle
1. Check the parts of the product overview.
10
9
2. Put the lower handle (9) in the mower body (10).
17
9
20
10
8
3. Turn the adjust knob (20) to level 1.
4. Tilt the lower handle (9) forward.
10 17
5. Slide the bumper (17) completely on the mower
body (10) until the parts are in touch.
8
6. Remove the 2 R-Clips (8) from the holes.
7. Tilt the lower handle (9) firmly backward.
8
8. Put the 2 R-clips (8) through the holes in the
handle locks on both sides.
To assemble the middle handle
1
16
4
1
9
1610
8
1. Put the middle handle (16) in the lower handle
(9).
Make sure that the handle holes are inline.
8
17 - 001 -
2. Push the push button (1) on the left side in the
handles.
3. Push the cable hook pin (4) on the right side in
the handles.
18
4. Put the 2 R-clips (8) along the grooves on the
push button and the cable hook pin.
To assemble the upper handle
16
15
12
16
13
1
21
17
17
1
15
1
16
1. Put the upper handle (15) on the middle handle
(16).
Make sure that it is fully in place and the
handle holes are inline.
2. Push the handle bolts (5) through the holes.
3. Put the washer (6) and the wing knob (2) on the
left side (with the cable) on the handle bolt (5).
4. Put the washer (6) and the cable hook knob (3)
on the right side on the handle bolt (5).
5. Tighten the wing knob (2) and the cable hook
knob (3).
6. Fix the cable (21) to the upper handle (15) and
middle handle (16) with the cable clips (7).
7. Check that the cable (21) is not trapped between
the middle handle (16) and the upper handle
(15).
To assemble the grass box
11
19
1. Put the tongues of the grass box chute (11) into
the grooves of the grass box (19) and push the
grass box chute (11) into the grass box (19) until
the connections click.
13
19
2. Put the hooks of the grass box cover (13) into the
grooves of the grass box (19)
3. Push the grass box cover (13) on the grass box
(19) until the connections click.
Make sure that all connections are
connected.
17 - 001 -
9
14
13
4. Push the grass box handle (14) into the grass
box cover (13) until the connections click.
To assemble the grass box lid
1610
1612
1. Put the grass box lid (12) in the mower body
(10).
Operation
Before you do operation
WARNING!
• Risk of physical injury!
• Cut injury when the blade turns or
the product starts accidentally.
• Wait for the blade to stop, disconnect
the product from the mains and use
gloves before you connect or
transport the product.
To connect the mower
WARNING!
• Risk of electric shock!
• To avoid damage to the mains cable,
the mains cable must be inserted into
the cable lock (L).
• Before you operate insert the mains
cable into the cable lock (L)
16
L
1. Loop the mains cable, insert the loop into the
cable lock (L) and pull tight.
2. Connect the mains cable into a 230 V mains
socket.
To start the mower
WARNING!
• Risk of physical injury!
• Risk of injury if the product does not
stop when you release the start
lever.
• Do not bypass the safety devices or
switches. For example do not attach
the start lever (22) to the handle.
1
23
1
22
To start:
The product is fitted with a two-handed safety device
(start lever (22) with safety interlock (23)) to prevent
the product from being turned on by accident.
There are two start levers (22) fitted. Either one have
to be used to start.
1. Connect the mains cable into a 230 V mains
socket.
2. Push the safety interlock (23) with one hand and
pull the start lever (22) with the other hand.
3. Release the safety interlock (23).
The product will start.
To stop:
1. Release the start lever (22).
10
17 - 001 -
To adjust the cutting height
The cutting height can be adjusted from 12 to 32 mm
in 4 positions.
1
20
1. Turn the adjust knob (20) counterclockwise to
lower the cutting height.
2. Turn the adjust knob (20) clockwise to increase
the cutting height.
To use the mower with the grass box
WARNING!
• Risk of physical injury!
• Cut injury when the blade turns or
the product starts accidentally.
• Wait for the blade to stop, disconnect
the product from the mains and use
gloves before you put / remove the
grass box.
• Do not put your hands in the
discharge opening.
1612
1614
1. Open the lid (12).
2. Put the grass box into the product by the handle
(14).
3. Close the lid (12).
4. Make sure that the grass box is securely
connected.
5. Start the product.
The transparent lid (12) shows the filling
level of the grass box.
6. Stop the product when the grass box is filled
completely.
7. Open the lid (12).
8. Remove the grass box of the product by the
handle (14).
9. Empty the grass box.
To use the mower without the grass
box
For larger areas of grass where grass collection is
not required you can use the product without the
grass box. The cut grass drop on the lawn.
1. Open the lid (12).
2. Remove the grass box of the product by the
handle (14).
3. Close the lid (12).
Tips to use the mower
1. Mow twice a week during the growing season.
The lawn will suffer if more than a third of its
length is cut at one time and this may also result
in poor collection.
2.
For the best
results mow the outside edge of the lawn in a
clockwise direction first.
3. Start to mow the edge of the lawn nearest to the
power point.
So the cable is laid out on the lawn you have
already cut.
4.
For best grass
collection always mow in a straight line. Do not
swing the lawnmower from side to side.
5. For the best cutting results mow in straight lines
with an overlap of approximately 8 - 10 cm on
each pass with the mower.
6. Do Not overload the mower.
To mow long thick grass may cause the motor
speed to drop and you will hear a change in the
motor sound. If the motor speed drops you may
overload the mower which may cause damage.
When you mow in long thick grass a first cut with
the cutting height set higher will help reduce the
load. See adjusting the cutting height.
17 - 001 -
11
Maintenance
Before you do maintenance
WARNING!
• Risk of physical injury!
• Cut injury when the blade turns or
the product starts accidentally.
• Wait for the blade to stop, disconnect
the product from the mains and use
gloves before you do maintenance.
To clean the product:
WARNING!
• Electric shock!
• Risc of injury and risk of damage to
the product.
• Do not clean the product with water
or with a water jet (in particular highpressure water jet).
To clean the underside of the
product:
The underside is easiest to clean after you mowed.
1
24
Use gloves.
1. Lay the product on its side carefully.
2. Clean the underside, the blade and the airflow
slots (24) with a brush (do not use sharp
objects).
To clean the overside of the product
and the grass box:
Do not clean with chemicals including petrol or
solvents.
1. Clean the overside with a damp cloth.
2. Clean the air intakes and the grass box with a
soft brush (do not use sharp objects).
Storage
To put into storage:
The product must be stowed away from children.
11
1. Disconnect the product from the mains.
2. Clean the product (see Maintenance).
3. To save space, push the push button (1) until the
joints can be folded together easily.
16
H
4. Wind the cable around the cable hooks (To
release the cable pull the hook (H) away from the
handle).
5. Stowe the product in a dry, enclosed and secure
place.
Disposal (in accordance with
RL2012/19/EC):
The product must not be added to normal household
waste. It must be disposed of in line with local
environmental regulations.
12 17 - 001 -
IMPORTANT!
Make sure that the product is discarded through or
via your municipal recycling collection centre.
Troubleshooting
Before you do troubleshooting
WARNING!
• Risk of physical injury!
• Cut injury when the blade turns or
the product starts accidentally.
• Wait for the blade to stop, disconnect
the product from the mains and use
gloves before you do
troubleshooting.
To clean the bumper
Clean the bumper when the adjust knob (20) locks.
8
1. Remove the 2 R-clips (8) of the handle locks on
both sides.
17
9
20
10
8
2. Turn the adjust knob (20) to level 1.
3. Tilt the lower handle (9) forward.
4. Remove the bumper (17) of the mower body
(10).
5. Clean the bumper (17).
6. Assemble the bumper (see Assembly).
To replace the blade
WARNING!
• Risk of physical injury!
• Cut injury when the blade turns and it
is damaged, bent, out of balance or
has chipped edges.
• Do not use the product when the
blade is damaged, bent, out of
balance or has chipped edges.
• Do not regrind the blade.
The FLYMO spare parts are availible from your
FLYMO dealer or from the FLYMO service.
Only use an original FLYMO blade:
• FLYMO replacement blade reference no.
FLY070. Part no. 5898064-90.
1. Let the blade replace by the FLYMO Service or a
specialist dealer authorised by FLYMO .
Troubleshooting table
Problem Possible Cause Remedy
Engine does not start.
Extension cable is disconnected or
damaged
Connect the extension cable or if
necessary replace it.
Blade is blocked. Remove the obstacle.
Engine is jammed and makes a
noise.
Blade is blocked. Remove the obstacle.
17 - 001 - 13
Problem Possible Cause Remedy
Cutting height is too low. Raise the cutting height.
Loud noises, the mower is rattling.
Screws on engine, its fixing or on
the mower chasing are losse.
Have screws tightened by an authorised specialist dealer or the
FLYMO Service.
Mower runs unevenly or vibrates
strongly.
Blade is damaged or the blade
mounting is released.
Have blade tightened or replaced
by an authorised specialist dealer
or the FLYMO Service.
Blade is very dirty. Clean the mower (see Mainte-
nance). If this does not rectify the
problem, contact the FLYMO Service.
The adjust knob is locked.
The bumper is dirty. Clean the bumper.
Poor grass collection.
Lid is not correct in place. Put the lid correct on the grass
box.
Airflow slots are dirty. Clean the mower (see Mainte-
nance).
Lawn is not cleanly cut.
Blade is blunt or damaged. Have blade replaced by the FLY-
MO Service.
Cutting height is too low. Raise the cutting height.
Repairs
For other malfunctions speak to the FLYMO
servicing department. Repairs must only be done by
FLYMO servicing departments or specialist dealers
approved by FLYMO .
Technical data
Electric Lawnmower
Unit Value (Art. 9670907-01 / 9670908-01)
Rated Power: W 1700
Mains voltage: V 230
Mains frequency: Hz 50
Speed of rotation cutting blade: R/min. 4200
Cutting width: cm 33
Cutting height adjustment (4 positions): mm 12 - 32
Volume of grass box: l 22
Weight: kg 10.5
14 17 - 001 -
Unit Value (Art. 9670907-01 / 9670908-01)
Sound pressure level L
PA
1)
:
Uncertainty k
PA
dB (A)
89
3
Sound power level L
WA
2)
: measured/guaranteed
Uncertainty k
WA
dB (A)
91 / 93
1,93
Hand/arm vibration a
vhw
1)
:
Uncertainty k
a
m/s
2
<2,5
1,5
Measuring process complying with: 1) EN
60335-2-77 ; 2) RL 2000/14/EC
Note:
The stated vibration emission value has been
measured according to a standardized test
procedure and can be used for comparison of one
electric power tool with another. It can also be used
for preliminary evaluation of exposure. The vibration
emission value can vary during actual use of the
electric power tool.
EC Declaration of Conformity
The undersigned, Husqvarna AB, 561 82 Huskvarna,
Sweden, hereby certifies that, when leaving our
factory, the units indicated below are in accordance
with the harmonised EU guidelines, EU standards of
safety and product specific standards. This
certificate becomes void if the units are modified
without our approval.
Description of the product: Electric Lawnmower
Product type: Glider Compact 330 VC ; Glider Compact 330 VCX
Article number: 9670907-01 ; 9670908-01
EC-Directives: 2006/42/EC; 2014/30/EC; 2000/14/EC; 2011/65/EC
Harmonised EN: EN ISO 12100; EN 60335-1; EN 60335-2-77
Deposited documentation: GARDENA Technical Documentation, M. Kugler, 89079 Ulm
Conformity Assessment according to: 2000/14/EC Procedure: art. 14 Annex VI
Noise level measured/guaranteed
Art. 9670907-01 / 9670908-01 : 91 / 93 [dB (A)]
Year of CE marking:
2017
Date:
Ulm, 07.12.2017
Authorized representative:
J. Thompson (Product and Marketing Director EUAP)
Accessories
For Electric Lawnmower
FLYMO replacement blade As replacement for blunt blade.
reference no. FLY070. Part no.
5898064-90
17 - 001 - 15
Service / Warranty
Service
For service speak to the manufacturer. See contact
information on back matter.
Warranty
FLYMO warranties this product for 2 years (from
date of purchase). This warranty includes all
important defects of the unit that can be proved to be
material or manufacturing faults. Under warranty we
will replace the product or repair it for no cost if these
conditions are applicable:
• The product must have been used properly and
in keeping with the requirements of the operation
instructions.
• Neither the purchaser or a not approved third
party have tried to repair the product.
This manufacturer’s warranty does not have an
effect on the user’s existing warranty claims against
the dealer / seller. If you have problems with this
product, please contact our Service or send the
defective product together with a short description of
the problem – if there is a warranty, with a copy of
the receipt – postage paid to FLYMO.
Consumable
The blade is a consumable and is not included in the
warranty.
Product liability
We expressly point out that, in accordance with the
product liability law, we are not liable for any damage
caused by our products if it is because of improper
repair or if parts replaced are not original FLYMO
parts or approved parts, and, if the repairs were not
done by a FLYMO Service Centre or an approved
specialist. The same applies to spare parts and
accessories.
16
17 - 001 -
17 - 001 - 17
18 17 - 001 -
17 - 001 - 19
www.husqvarna.com
Original instructions
VC330-20.960.01/1217
Loading...