Flymo EasiStore 300R Li, EasiStore 340R Li User guide

Page 1
®
EN Operator’s manual
Battery Lawnmower
EasiStore 300R Li Art. 9679877-01 EasiStore 340R Li Art. 9679878-01
Page 2
A1 A2 A3
A4 A5 A6
A7 A8 A9
A10 O1 O2
2
Page 3
O3 O4 O5
O9
O10
O8
O11
O12
3
S1 T1
Page 4
EN
1. SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
3. OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
4. MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5. STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
6. TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
7. TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
8. ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
9. SERVICE / WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Original instructions.
Preparation
a) While operating the machine always wear substantial footwear and long
trousers. Do not operate the machine when barefoot or wearing open sandals. Avoid wearing clothing that is loose fitting or that hanging cords or ties.
b) Thoroughly inspect the area where the machine is to be used and remove all
objects which can be thrown by the machine.
c) Before using, always visually inspect to see that the blade, blade bolt and the
blade assembly are not worn or damaged. Replace worn or damaged com­ponents in set to preserve balance. Replace damaged or unreadable labels.
d) Before use check the supply and extension cord for signs of damage or
aging. If the cord becomes damaged during use, disconnect the cord from the supply immediately. DO NOT TOUCH THE CORD BEFORE DISCONNECTING THE SUPPLY. Do not use the machine if the cord is damaged or worn.
This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the product by a person responsible for their safety. Children should be supervised to ensure that they do not play with the product. The use of this product by young people under the age of 16 is not recommended.
Intended use:
The FLYMO Battery Lawnmower is intended to mow lawn in private domestic gardens and allotments.
The product is not intended for long term use.
DANGER! Risk of injury! Do not use the product to cut bushes, hedges, shrubs, to cut of climbers or grass on roofs or balcony boxes, to chop up branches, twigs and to level irregularities in the soil. Do not use the product on a slope steeper than 20° maximum.
1. SAFETY
IMPORTANT! Read the operator’s manual carefully before use and keep for future reference.
Symbols on the product:
Read operator’s manual.
Operation
a) Operate the machine only in daylight or in good artificial light. b) Avoid operating the machine in wet grass. c) Always be sure of your footing on slopes. d) Walk, never run. e) Mow across the face of slopes, never up and down. f) Exercise extreme caution when changing direction on slopes. g) Do not mow excessively steep slopes. h) Use extreme caution when reversing or pulling the machine towards you. i) Stop the blade(s) if the machine has to be tilted for transportation when
crossing surfaces other than grass, and when transporting the machine to and from area to be used.
j) Never operate the machine with defective guards or shields, or without safety
devices, for example deflectors and / or grass collector, in place.
k) Switch on the motor carefully according to instructions and with feet well
away from the blade(s).
l) Do not tilt the machine when switching on the motor, except if the machine
has to be tilted for starting. In this case, do not tilt it more than absolutely
necessary and lift only the part, which is away from the operator. m) Do not start the machine when standing in front of the discharge opening. n) Do not put hands or feet near or under rotating parts. Keep clear of the
discharge opening at all times. o) Do not transport the machine while the power source is running.
) Stop the machine, and remove the disabling device. Make sure that all moving
p
2
parts have come to a complete stop: – whenever you leave the machine, – before clearing blockages or unclogging chute, – before checking, cleaning or working on the machine, – after striking a foreign object. Inspect the machine for damage and make
repairs before restarting and operating the machine;
if the machine starts to vibrate abnormally (check immediately) – inspect for damage, – replace or repair any damaged parts, – check for and tighten any loose parts.
Keep bystanders away.
Not valid for the battery mower.
Beware of sharp blades. Blades continue to rotate
after the motor is switched off.
Remove disabling device before maintenance.
Secure the working area before starting to work. Watch out for hidden cables.
General safety warnings
Electrical safety
DANGER! Electric shock! Risk of injury due to electric shock.
v The product must be supplied through a residual current device (RCD)
having a rated residual operating current not exceeding 30 mA.
Training
a) Read the instructions carefully. Be familiar with the controls and the correct
use of the machine.
b) Never allow children or people unfamiliar with these instructions to use the
machine. Local regulations can restrict the age of the operator.
c) Never operate the machine while people, especially children, or pets are
nearby.
d) Keep in mind that the operator or user is responsible for accidents or hazards
occurring to other people or their property.
Maintenance and storage
a) Keep all nuts, bolts, and screws tight to be sure the machine is in safe work-
ing condition. b) Check the grass collector frequently for wear or deterioration. c) Replace worn or damaged parts for safety. d) On machines with multi blade, take care as rotating one blade can cause
other blades rotate. e) Be careful during adjustment of the machine to prevent entrapment of the
fingers between moving blades and fixed parts of the machine. f) Always allow the machine to cool down before storing. g) When servicing the blades be aware that, even though the power source is
switched off, the blades can still be moved. h) Use only genuine replacement parts and accessories.
Additional safety warnings
Battery safety
DANGER! Fire risk!
The battery to be charged must be placed on a nonflammable, heat resistant and non-conductive surface while charging.
The battery must not be charged unattended. The supply terminals are not to be short-circuited. Keep corrosive, flammable and easily combustible objects clear of the
battery charger and the battery. Do not cover the battery charger and the battery while charging.
Disconnect the battery charger immediately in the event of smoke formation or fire.
Only use FLYMO batteries for the FLYMO battery product. FLYMO cannot accept any liability for the batteries of other manufacturers. If they are of minor quality, they could cause a fire or explosion hazard!
4
Page 5
Do not use the FLYMO charger to charge external rechargeable batteries, as FLYMO cannot guarantee compatibility and could therefore present a risk of fire or explosion.
Do not charge non-rechargeable batteries.
Protect batteries from heat and fire. Do not leave on radiators or expose to strong sunshine for long periods.
Do not operate them in explosive atmospheres, e. g. in the presence of flammable liquids (vapours), flammable gases or accumulations of dust. Batteries may create sparks which could ignite the mixtures.
Check your replacement battery before each use. Visually check the battery before each use. A non-functioning battery must be disposed of correctly. Do not send by post. For further details, please contact your local disposal companies.
For risks of injury do not use the battery as a power source for other products. Only use the battery for the FLYMO product intended.
Only charge and use the battery in ambient temperatures of between 0 °C and 40 °C. Allow battery to cool down after long periods of use.
Check the charging cable regularly for signs of damage or ageing (brittleness). Only use it in perfect condition.
Do not stow or transport the battery above 45 °C or in direct sunlight. Ideally, the battery should be stored below 25 °C so that self-discharge is low.
Do not expose the battery to rain, water (immersion) or wet conditions. Keep battery in order (clean) especially air vents. If usage of the battery is not planned for a certain time (winter period) reload the
battery to avoid a deep discharge. Do not store the battery in a product to prevent self-discharge, misuse and acci-
dents. Do not store the battery in places where static electricity is present.
Electrical safety
This product makes an electromagnetic field while it operates. This field may under some conditions interfere with active or passive medical implants. To decrease the risk of conditions that can possibly injure or kill, we recommend persons with medical implants to speak with their physician and the medical implant manufacturer before you operate the product.
Only use the battery product between 0 °C bis 40 °C. Do not use under wet conditions.
Personal safety
Small parts can be easily swallowed. There is also a risk that the polybag can suffocate toddlers. Keep toddlers away when you assemble the product.
Do not use the start levers alternately. Do not disassemble the product further than the delivery status. Use gloves, wear slip resistant shoes and wear eye protection. Do not overload the mower. Never operate the product when you are tired, ill or under the influence of alcohol,
drugs, or medicine.
Danger of slipping: – in wet grass – on steep slopes – during transport Be careful while going backwards.
DANGER! Risk of explosion!
DANGER! Cardiac arrest!
DANGER! Risk of suffocation!
7. Put the upper handle on the lower handles and slide the screws through the boreholes (there are 2 holes in the lower handle to choose the desired height).
8. Put the washers on the screws.
9. Screw the locking nuts onto the screws.
10. Attach the control cable with the cable clips.
To assemble the grass box [ Fig. A5 / A6 / A7 / A8 / A9 ]:
1. Push the grass box handle into the slots in the grass box cover until it
audibly engages.
2. Slide the grass box tongue into the slots in the grass box until it audibly
engages.
3. Align the grass box cover and the grass box locators.
4. Fold the grass box cover towards the grass box.
5. Push the grass box cover on the grass box. Make sure that all clips are
snapped in correctly.
To attach the grass box to the lawnmower [ Fig. A10 ]:
1. Lift the protective cover.
2. Attach the grass box to the hooks on the rear of the mower.
3. OPERATION
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, remove the battery, remove the
safety key and use gloves before you adjust or transport the product.
To charge the batteries [ Fig. O1 ]:
CAUTION!
Overvoltage damages the batteries and the battery
charger.
v Make sure that you use the correct mains voltage.
Before you use the batteries the first time, the batteries must be com­pletely charged.
The lithium-ion batteries can be charged in any state of charge and the charging process can be disconnected at any time without to damage the batteries (no memory effect).
1. Connect the battery charger into a mains socket.
2. Connect the battery charger cable to the batteries.
When the charging control lamp at the charger flashes green and the 3 green LEDs on the battery light up one after the other, the battery is being charged.
When the charging control lamp at the charger illuminates permanently green the battery is completely charged
(Charging time, see 7. TECHNICAL DATA ).
3. Examine the charge status regularly while you charge.
4. When the batteries are completely charged, disconnect the
batteries from the charger.
5. Disconnect the charger from the mains.
2. ASSEMBLY
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Remove the battery, remove the safety key and use gloves
before you assemble the product.
To assemble the handle [ Fig. A1 / A2 / A3 /A4 ]:
1. Put the springs on the shafts.
2. Put the handle plates on the shafts.
3. Put the lower handle on the shafts.
4. Put the washers on the shafts.
5. Insert the bolts into the quick-release levers.
6. Screw the quick-release levers loosely onto the shafts and clamp them down.
Battery charging indicator [ Fig. O2 ]:
v Push the button on the battery.
The battery charging indicator is displayed for 5 seconds.
> 2/3 charged 3 green LEDs illuminate
> 1/3 charged 2 green LEDs illuminate
< 1/3 charged 1 green LED illuminates
reserve 1 green LED flashes
To adjust the cutting height:
For the first cut of the season, always cut on the highest cutting height possible, and gradually lower the cutting height over successive cuts to your desired height for the lawn.
Only for 300R Li (in 3 positions) [ Fig. O3 / O4 / O5 / O6 / O7]:
The cutting height can be adjusted from 25 – 65 mm.
Position ‘Low’ (25 mm): Cutting height setting should only be used on well maintained ‘manicured lawns’ without excessive moss or thatch.
5
Page 6
Position ‘Mid’ (45 mm): Cutting height setting is the suitable for most lawns.
Position ‘High’ (65 mm): Cutting height setting is used when you lawn has excessive growth such as following holidays or first cut of the season.
v Move both axles to the desired position in the E-Gate. Make sure that
both sides of the axle are in the same position. Make sure that both axles are in the same position.
Only for 340R Li (in 5 positions) [ Fig. O8 ]:
The cutting height can be adjusted from 20 – 60 mm (from rear to front).
Position 1 (20mm): Cutting height setting should only be used on well maintained ‘manicured lawns’ without excessive moss or thatch.
Position 2 (30 mm): Cutting height setting is the suitable for most lawns.
Position 3 (40 mm): Cutting height setting is the suitable for most lawns.
Position 4 (50 mm): Cutting height setting is the suitable for most lawns.
Position 5 (60 mm): Cutting height setting is used when you lawn has
excessive growth such as following holidays or first cut of the season.
1. Pull the lever to the wheel.
2. Move the lever to the desired position.
3. Release the lever and let it engage.
To start the mower [ Fig. O9 / O10 ]:
DANGER! Risk of injury!
Risk of injury if the product does not stop when you
release the start lever.
v Do not bypass the safety devices or switches. For example
do not attach the start lever to the handle.
To start:
The product is provided with a two-switch safety device (safety key with starting lockout) to prevent the product from being turned on by accident.
There are two start levers. Either one has to be used to start.
1. Open the battery cover.
2. Put the batteries into the battery holders until they audibly engages.
3. Put the safety key into the mower and turn it to position I.
4. Push the starting lockout with one hand and pull the start lever with
the other hand.
The mower starts.
5. Release the starting lockout.
Only for 340R Li [ Fig. O11 ]: The level indicator opens during mowing. When it closes during mowing, the grass box is full and must be emptied.
Transport position [ Fig. . O12 ]:
The easy transport position provides additional mobility due to its upright driving position. Easy to get on and off the lawn at any distance.
1. Attach the grass box to the switch box (see 5. STORAGE).
2. Pull the mower to and from the lawn when it is set in the storage position.
4. MAINTENANCE
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, remove the battery, remove the
safety key and use gloves before you maintain the product.
To clean the mower [ Fig. M1 ]:
DANGER! Risk of injury!
Risk of injury and risk of damage to the product.
v Do not clean the product with water or with a water jet
(in particular high-pressure water jet).
v Do not clean with chemicals including petrol or solvents.
Some can destroy critical plastic parts.
The airflow slots must always be clean.
To clean the underside of the mower:
The underside is easiest to clean after you mowed.
1. Lay the mower on its side carefully.
2. Clean the underside, the blade and the discharge opening with a brush (do not use sharp objects).
To clean the overside of the mower and the grass box:
1. Clean the overside with a damp cloth.
2. Clean the airflow slots and the grass box with a soft brush (do not use sharp objects).
To clean the battery and the battery charger:
Make sure that the surface and the contacts of the battery and the battery charger always are clean and dry before you connect the battery charger.
Do not use running water.
v Clean the contacts and the plastic parts with a soft and dry cloth.
To stop:
1. Release the start lever.
The mower stops.
2. Turn the safety key to position 0 and remove it.
Tips to use the mower:
If grass residue is left in the discharge opening, pull the mower backwards about 1 m so that the grass residue can drop out downwards.
To produce a well-maintained lawn and optimise the cutting performance, we recommend to cut the lawn regularly once a week if possible. The lawn becomes denser if you cut it frequently.
After relatively long cutting intervals (holiday lawn), first of all cut in one direction with the highest cutting height and then cut in the crosswise direction with the required cutting height.
If possible, only cut the grass when it is dry, if the grass is damp, the cutting pattern will be uneven.
Cutting performance and battery charge:
The lawn area which can be cut on each battery charge depends on several factors such as moisture, grass density and cutting height. In order to ensure an optimal use of space, do not turn the mower on and off too frequently as this severely reduces the battery running time. The cutting performance for each battery charge can be ideally utilised by increasing the cutting height and frequent mowing.
Rear Roller:
For lawnmowers fitted with a rear roller, it is possible to create a striped effect on the lawn. For the best stripe results, we recommend cutting on the lowest possible cutting height suited to your lawn. The stripe effect will fade in time between cuts.
5. STORAGE
To put into storage [ Fig. O9 ]:
The product must be stored away from children.
1. Turn the safety key to position 0 and remove it.
2. Remove the battery.
3. Charge the battery.
4. Clean the mower, the battery and the battery charger (see 4. MAINTENANCE).
5. Store the mower, the battery and the battery charger in a dry, enclosed and frost-free place.
Easi Storage position [ Fig. S1 ]:
1. Remove the grass box.
2. Set on the highest cutting height.
3. Fold the handle flat and lock it in position 4.
4. Stand the mower upright.
5. Make sure that the grass box is completely empty.
6. Attach the grass box to the switch box with the storage hook. Make sure that the grass box is completely secured, the storage function is accomplished.
7. Store the mower in upright position.
Disposal:
(in accordance with RL2012/19/EC)
The product must not be disposed of to normal household waste. It must be disposed of in line with local environmental regulations.
6
Page 7
IMPORTANT!
v Dispose of the product through or via your municipal recycling
collection centre.
Disposal of the battery:
The FLYMO battery contains lithium-ion cells that should not be disposed of with normal household waste at the end of its life.
Li-ion
IMPORTANT!
v Dispose of the batteries through or via your municipal recycling
collection centre.
1. Discharge the lithium-ion cells completely (contact the FLYMO Service).
2. Protect the contacts on the lithium-ion cells against short circuits.
3. Dispose of the lithium-ion cells properly.
6. TROUBLESHOOTING
Problem Possible Cause Remedy
After pushing the button no LED on the battery illuminates
After pushing the button the LED on the battery flashes red.
Charging control lamp on the charger does not illuminate
Charging control lamp on the charger illuminates red
Charging control lamp on the charger flashes red
NOTE: For any other malfunctions please contact the FLYMO Customer Service.
Repairs must only be done by FLYMO service departments or specialist dealers approved by FLYMO.
Battery is defective. v Replace the battery.
Battery temperature is out of range.
Battery charger or charging cable are not connected correctly.
Battery temperature is out of range.
Battery error / battery defective. v If the battery cannot be
v Use the battery in surround-
ings where temperatures are between 0 °C and 40 °C.
v Connect the battery charger
and charging cable correctly.
v Use the battery in surround-
ings where temperatures are between 0 °C and 40 °C.
reset by connecting it to the charger, contact the FLYMO Service.
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, remove the battery, remove the
safety key and use gloves before you troubleshoot the product.
To replace the blade [ Fig. T1 ]:
DANGER! Risk of injury!
Cut injury when the blade turns and it is damaged,
bent, out of balance or has chipped edges.
v Do not use the mower when the blade is damaged, bent,
out of balance or has chipped edges.
v Do not regrind the blade.
The FLYMO spare parts are available from your FLYMO dealer or from the FLYMO service.
Only use an original FLYMO blade:
• FLYMO replacement blade for 300R Li: Art. FLY 069
• FLYMO replacement blade for 340R Li: Art. FLY 087
1. Unscrew the blade bolt.
2. Remove the blade bolt and the washer.
3. Remove the blade and the spacer.
4. Put the spacer and the new blade on the mower.
5. Put the washer on the blade bolt.
6. Screw the new blade tight with the blade bolt.
Problem Possible Cause Remedy
Mower does not start Safety key is not in position I. v Turn the safety key to
Battery is not put completely
Battery is empty. v Charge the battery.
Motor is blocked. v Remove the obstacle.
Engine is jammed and makes a noise
Cutting height is too low. v Raise the cutting height.
Loud noises, the mower is rattling
Mower runs unevenly or vibrates strongly
Blade is very dirty. v Clean the blade.
Lawn is not cleanly mowed Blade is blunt or damaged. v Replace the blade.
Cutting height is too low. v Raise the cutting height.
Red Error-LED on the battery illuminates
into the battery holder.
Motor is blocked. v Remove the obstacle.
Screws on engine, its fixing or on the mower chasing are loose.
Blade is damaged / worn or the blade mounting is released.
Battery temperature is out of range.
position I.
v Put the battery completely
into the battery holder until it audibly engages.
Start again.
Start again.
v Let the screws be tightened
by an authorised specialist dealer or the FLYMO Service.
v Replace the blade.
v Use the battery in surround-
ings where temperatures are between 0 °C and 40 °C.
7. TECHNICAL DATA
Battery Lawnmower
Speed of rotation cutting blade
Cutting width cm 30 34
Cutting height adjustment mm
Volume of grass box l 30 35
Weight (without Battery) kg 8.0 10.4
Sound pressure level L Uncertainty k
Sound power level L measured / guaranteed Uncertainty k
Hand / arm vibration a
Measuring process complying with: 1) EN 60335-2-77 2) RL 2000/14/EC
NOTE: The stated vibration emission value has been measured according to
sure. The vibration emission value can vary during actual use of the electric power tool.
pA
WA
astandardized test procedure and can be used for comparison of one electric power tool with another. It can also be used for preliminary evaluation of expo-
Battery B16-2025A
Battery voltage V (DC) 20
Battery capacity Ah 2,5
Number of cells (Li-Ion) 5
Battery charging time (approx.)
Lawn area per battery charge (approx.)
Appropriate FLYMO System Batteries B16-2025A: Art. 967913201
Battery Charger 20 V
Mains voltage V (AC) 120
Mains frequency Hz 50 – 60
Rated Power W20
Output voltage V (DC) 20
Max. output current mA 1000
Appropriate FLYMO Battery Chargers 18 V: Art. 967913301
Unit Value
R/min 3500 3300
1)
pA
dB (A)
2)
:
WA
dB (A)
1)
m/s
vhw
Unit Value ( Art. 967913201)
min. 120
m
Unit Value ( Art. 967913301)
EasiStore 300R Li
25 – 65 (3 positions)
84 3
88 / 90
1.88
2
< 2.5 < 2.5
2
250
Value EasiStore 340R Li
20 – 60 (5 positions)
83 3
86 / 89
2.17
8. ACCESSORIES
FLYMO Replacement Battery B16-2025A
FLYMO Battery Charger 20 V
Battery for additional duration or for replacement.
Charger to charge the FLYMO Batteries B16-2025A
Art. 967913201
Art. 967913301
7
Page 8
FLYMO Replacement Blade for 300R Li
FLYMO Replacement Blade for 340R Li
As replacement for blunt blade. Art. FLY 069
As replacement for blunt blade. Art. FLY 087
9. SERVICE / WARRANTY
Service:
Please contact the address on the back page.
Warranty statement:
In the event of a warranty claim, no charge is levied to you for the services provided.
Husqvarna UK Ltd. grants a warranty for all original FLYMO new products for two years from the date of original purchasefrom the retailer, provided that the devices have been for private use only. This manufacturer’s war­ranty does not apply to products acquired second hand. This warranty includes all significant defects of the product that can be proved to be material or manufacturing faults. This war ranty is fulfilled by supplying afully functional replacement productor by repairing the faulty product sent to us free of charge; we reserve the right to choose between these options. This service is subject to the following provisions:
• The product has been used for its intended purpose as per the recommendations in the operating instructions.
• Neither the purchaser nor a third party has attempted to open or repair the product.
• Only Original FLYMO replacement parts and wear parts have been used for operation.
• Presentation of the receipt.
Normal wear and tear of parts and components (such as blades, blade fixing parts, turbines, light bulbs, V-belts / toothed belts, impellers, air filters, spark plugs), visual changes, wear parts and consumables are excluded from the warranty.
This manufacturer’s warranty is limited to replacement and repair of products in accordance with the abovementioned conditions. The manu­facturer’s warranty does not constitute an entitlement to lodge other claims against us as a manufacturer, such as for damages. This manu­facturer’s warranty does not, of course, affect statutory and contractual warranty claims against the dealer / retailer.
The manufacturer’s warranty is governed by the law of the Federal
Republic of Germany.
In case of a warranty claim, please return the faulty product, together with a copy of the receipt and a description of the fault, with postage paid to the service address.
Consumables:
The blade and the wheels are consumables and are not included in the warranty.
8
Page 9
PRODUCT LIABILITY
In accordance with the German Product Liability Act, we hereby expressly declare that we accept no liability for damage incurred from our products where said products have not been properly repaired by a FLYMO-approved service partner or where original FLYMO parts or parts authorised by FLYMO were not used.
EC DECLARATION OF CONFORMITY
The undersigned hereby certifies as the authorized representative of the manufacturer, Husqvarna AB, 561 82 Huskvarna, Sweden, that, when leaving our factory, the unit(s) indicated below is / are in accordance with the harmonised EU guidelines, EU standards of safety and product specific standards. This certificate becomes void if the unit(s) is / are modified without our approval.
Description of the product: Battery Lawnmower
Product type EasiStore 300R Li
Article-Number 9679877-01
CE-Directives 2006/42/EC
Harmonised EN EN ISO 12100
Deposited Documentation GARDENA Technical Documentation,
Conformity Assessment according to 2000/14/EC Procedure: ar t. 14 Annex VI
Noise level: measured / guaranteed EasiStore 300R Li: 88 dB(A) / 90 dB(A)
Year of CE marking: 2019
Ulm, 13.12.2019
Authorised representative:
EasiStore 340R Li
9679878-01
2014/30/ EU 2000/14/EC 2011/65/ EU
Charger: 2014/35/EC
EN 60335-1 EN 60335-2-77
Charger: EN 60335-2-29
Battery: EN 62133-2
M. Kugler, 89079 Ulm
EasiStore 340R Li: 86 dB(A) /89 dB(A))
John Thompson
Product and Marketing Director EUAP
9
Page 10
Deutschland /Germany
GARDENA Manufacturing GmbH Central Service
-
Lorenser-Straße 40
Hans
-
89079 Ulm
D Produktfragen: (+49) 731 490 Reparaturen: (+49) 731 490 service
Albania
COBALT Sh.p.k. Rr. Siri Kodra 1000 Tirana
Argentina
Husqvarna Argentina S.A. Av.del Libertador 5954 Piso 11–Torre B (C1428ARP) Buenos Aires Phone: (+54) 11 5194 5000 info.gardena ar.husqvarna.com
Armenia
Garden Land Ltd. 61 Tigran Mets 0005 Yerevan
Australia
Husqvarna Australia Pty. Ltd. Locked Bag 5 Central Coast BC NSW 2252 Phone: (+61) (0) 2 4352 7400 customer.service husqvarna.com.au
Austria /Österreich
Husqvarna Austria GmbH Industriezeile 36 4010 Linz Tel.: (+43) 732 770101 service.gardena husqvarnagroup.com
Azerbaijan
Firm Progress a. Aliyev Str. 26A 1052 Baku
Belgium
Husqvarna België nv/sa Gardena Division Rue Egide Van Ophem 111 1180 Uccle / Ukkel Tel.: (+32) 2 720 9212
@
info
Bosnia / Herzegovina
SILK TRADE d.o.o. Industrijska zona Bukva bb 74260 Tešanj
Brazil
Husqvarna do Brasil Ltda Av. Francisco Matarazzo, 1400 São Paulo CEP: 05001 Tel: 0800 marketing.br.husqvarna husqvarna.com.br
Bulgaria
AGROLAND България АД бул. 8 Декември, №13 Офис 5 1700 Студентски град София Тел.: (+359) 2466 6910
@
info
Canada /USA
GARDENA Canada Ltd. 100 Summerlea Road Brampton, Ontario L6T 4X3 Phone: (+1) 905 792 93 30
@
info
Chile
Maquinarias Agroforestales Ltda. (Maga Ltda.) Santiago, Chile Avda. Chesterton # 8355 comuna Las Condes Phone: (+56) 2 202 4417 Dalton Zipcode: 7560330
-
123
-
290
@
gardena.com
@
@
-
@
gardena.be
19º andar
SP
-
903
-
112252
@
agroland.eu
gardenacanada.com
@
maga.cl
485
China
Husqvarna (Shanghai) Management Co., Ltd.
富世华(上海)管理有限公司
3F, Benq Square B, No207, Song Hong Rd., Chang Ning District, Shanghai, PRC. 200335
上海市长宁区淞虹路207号明 基广场B座3楼,邮编:200335
Colombia
Husqvarna Colombia S.A. Calle 18 No. 68 D Industrial de Montevideo Bogotá, Cundinamarca Tel. 571 2922700 ext. 105 jairo.salazar husqvarna.com.co
Costa Rica
Compania Exim Euroiberoamericana S.A. Los Colegios, Moravia, 200 metros al Sur del Colegio Saint Francis Phone: (+506) 297 68 83 exim_euro
Croatia
Husqvarna Austria GmbH Industriezeile 36 4010 Linz Tel.: (+43) 732 770101 service.gardena husqvarnagroup.com
Cyprus
Med Marketing 17 Digeni Akrita Ave P.O. Box 27017 1641 Nicosia
Czech Republic
Husqvarna Česko s.r.o. Türkova 2319/5b 149 00 Praha 4 – Chodov Bezplatná infolinka: 800 100425
servis
@
cz.husqvarna.com
Denmark
GARDENA DANMARK Lejrvej 19, st. 3500 Værløse Tlf.: (+45) 70 264770 husqvarna www.gardena.com/ dk
Dominican Republic
BOSQUESA, S.R.L Carretera Santiago Licey Km. 5 ½ Esquina Copal II. Santiago Dominican Republic Phone: (+809) 736-0333 joserbosquesa
Ecuador
Husqvarna Ecuador S.A. Arupos E1-181 y 10 de Agosto
Quito, Pichincha Tel. (+593) 22800739 francisco.jacome husqvarna.com.ec
Estonia
Husqvarna Eesti OÜ Valdeku 132 EE-11216 Tallinn info
@
gardena.ee
Finland
Oy Husqvarna Ab Gardena Division Lautatarhankatu 8 B/PL 3 00581 HELSINKI www.gardena.fi
France
Husqvarna France 9/11 Allée des pierres mayettes 92635 Gennevilliers Cedex France http:// www.gardena.com/ fr N° AZUR: 0 810 00 78 23 (Prix d’un appel local)
-
31, zona
@
San José
@
racsa.co.cr
@
@
husqvarna.dk
@
claro.net.do
@
-
485
Georgia
Transporter LLC 8/57 Beliashvili street 0159 Tbilisi, Georgia Phone: (+995) 32214 7171
Great Britain
Husqvarna UK Ltd Preston Road Aycliffe Industrial Park Newton Aycliffe County Durham DL5 6UP info.gardena husqvarna.co.uk
Greece
Π.ΠΑΠΑΔΟΠΟΥΛΟΣ ΑΕΒΕ Λεωφ. Αθηνών 92 Αθήνα Τ.Κ.104 42 Ελλάδα Τηλ. (+30) 210 51 93100
info
Hungary
Husqvarna Magyarország Kft. Ezred u. 1 1044 Budapest Telefon: (+36) 1 251 vevoszolgalat.husqvarna husqvarna.hu
Iceland
Ó. Johnson & Kaaber Tunguhalsi 1 110 Reykjavik
@
ooj
Ireland
Husqvarna UK Ltd Preston Road Aycliffe Industrial Park Newton Aycliffe County Durham DL5 6UP info.gardena husqvarna.co.uk
Italy
Husqvarna Italia S.p.A. Via Santa Vecchia 15 23868 VALMADRERA (LC) Phone: (+39) 0341.203.111 assistenza.italia it.husqvarna.com
Japan
KAKUICHI Co. Ltd. Sumitomo Realty & Development Kojimachi BLDG., 8F
-
1 Nibanncyo
5 Chiyoda Tokyo 102 Phone: (+81) 33 264 4721 m_ishihara
Kazakhstan
LAMED Ltd. 155/1, Tazhibayevoi Str. 050060 Almaty IP Schmidt Abayavenue 3B 110 005 Kostanay
Korea
Kyung Jin Trading CO.,LTD. 107-4, SunDuk Bld., YangJae-dong, Seocho-gu, Seoul, (zipcode: 137-891) Phone: (+82) (0)2 574-6300
Kyrgyzstan
Alye Maki av. Moladaya Guardir J 3 720014 Bishkek
Latvia
Husqvarna Latvija SIA Ulbrokas 19A
LV-1021 Rīga
info
Lithuania
UAB Husqvarna Lietuva Ateities pl. 77C
-
LT info
@
@
papadopoulos.com.gr
-
3
-
4161
ojk.is
@
@
-
ku
-
0084
@
kaku-ichi.co.jp
@
gardena.lv
52104 Kaunas
@
gardena.lt
@
Luxembourg
Magasins Jules Neuberg 39, rue Jacques Stas Luxembourg Case Postale No. 12 Luxembourg 2010 Phone: (+352) 401401
@
api
Mexico
AFOSA Av. Lopez Mateos Sur # 5019 Col. La Calma 45070 Zapopan, Jalisco Mexico Phone: (+52) 33 3818 icornejo
Moldova
Convel S.R.L. 290A Muncesti Str. 2002 Chisinau
Netherlands
Husqvarna Nederland B.V. GARDENA Division Postbus 50131 1305 AC ALMERE Phone: (+31) 36 5210010 info
Neth. Antilles
Jonka Enterprises N.V. Sta. Rosa Weg 196 P.O. Box 8200 Curaçao Phone: (+599) 9 767 66 55 pgm
New Zealand
Husqvarna New Zealand Ltd. PO Box 76 Manukau City 2241 Phone: (+64) (0) 9 9202410 support.nz
Norway
Husqvarna Norge AS Gardena Division Trøskenveien 36 1708 Sarpsborg info
Peru
Husqvarna Perú S.A. Jr. Ramón Cárcamo 710 Lima 1 Te l : (+51) 1 3 320400 ext. 416 juan.remuzgo husqvarna.com
Poland
Husqvarna Poland Spółka zo.o. ul. Wysockiego 15 b
-
03 Phone: (+ 48) 22 330 9600 gardena
Portugal
Husqvarna Portugal, SA Lagoa 2635 Tel.: (+351) 21 922 85 30 Fax : (+351) 21 922 85 36 info
Romania
Madex International Srl Soseaua Odaii 117 RO 013603 Bucure Phone: (+ 40) 21 352.76.03
madex
Russia /Россия
ООО „Хускварна“ 141400, Московская обл., г. Химки, улица Ленинградская, владение 39, стр.6 Бизнес Центр „Химки Бизнес Парк“, помещение ОВ02_04 http: //www.gardena.ru
Serbia
Domel d.o.o. Autoput za Novi Sad bb
11273 Belgrade Phone: (+381) 118488812 miroslav.jejina
-
Gasperich 2549
neuberg.lu
@
afosa.com.mx
@
gardena.nl
@
jonka.com
-
437
@
husqvarna.co.nz
@
gardena.no
@
371 Warszawa
@
husqvarna.com.pl
-
Albarraque
-
595 Rio de Mouro
@
gardena.pt
@
ines.ro
@
domel.rs
-
123,
ş
ti, S1
-
3434
Singapore
Hy-Ray PRIVATE LIMITED 40 Jalan Pemimpin #02
-
08 Tat Ann Building Singapore 577185 Phone: (+65) 6253 2277
@
hyray.com.sg
shiying
Slovak Republic
Husqvarna Česko s.r.o. Türkova 2319/5b 149 00 Praha 4 – Chodov Bezplatná infolinka: 800 154044
@
sk.husqvarna.com
servis
Slovenia
Husqvarna Austria GmbH Industriezeile 36 4010 Linz Tel.: (+43) 732 770101 service.gardena husqvarnagroup.com
South Africa
Husqvarna South Africa (Pty) Ltd Postnet Suite 250 Private Bag X6, Cascades, 3202 South Africa Phone: (+27) 33 846 9700
@
gardena.co.za
info
Spain
Husqvarna España S.A. Calle de Rivas nº10 28052 Madrid Phone: (+34) 91 708 05 00 atencioncliente
Suriname
Agrofix n.v. Verlengde Hogestraat #22 Phone: (+597) 472426
@
sr.net
agrofix Pobox : 2006 Paramaribo Suriname
Sweden
Husqvarna AB Gardena Division S gardenaorder
Switzerland /Schweiz
Husqvarna Schweiz AG Consumer Products Industriestrasse 10 5506 Mägenwil Phone: (+41) (0) 62 887 37 90 info
Turkey
Dost Bahçe Dış Ticaret Mümessillik A.Ş Yunus Mah. Adil Sok. No:3 Ic Kapi No: 1 Kartal 34873 Istanbul
Phone: (+90) 216 38 93 939 info
Ukraine / Україна
ТОВ «Хускварна Україна» вул. Васильківська, 34, офіс 204 03022, м. Київ Тел. (+38) 044 498 39 02
info
Uruguay
FELI SA Entre Ríos 1083 CP 11800 Montevideo Tel: (+598) 22031844 info
Venezuela
C Av. Caroní, Edif. Trezmen, PB. Colinas de Bello Monte. 1050 Caracas. Tlf: (+58) 212 992 33 22 info
0000
ES300RLi-20.960.01/1219
©
© GARDENA
Manufacturing GmbH
Manufacturing GmbH D-89070 Ulm
D-89070 Ulm
http://www.gardena.com
http: //www.gardena.com
South America
-
561 82 Huskvarna
@
@
gardena.ch
@
dostbahce.com.tr
-
г
@
gardena.ua
Uruguay
@
felisa.com.uy
orporación Casa y Jardín C.A.
@
casayjardin.net.ve
-
20.960.08/ 0618
GARDENA
-
485
@
@
gardena.es
husqvarna.se
10
Loading...