Flymo EasiGlide 360, EasiGlide 330, EasiGlide 300, EasiGlide 300V, EasiGlide 330V User guide

®

Page 1 width 2 mm less: 208 mm

EN Operator’s manual

Electric Hover Lawnmower

EasiGlide 300 Art. 970483001
EasiGlide 330 Art. 970483101
EasiGlide 360 Art. 970483201
EasiGlide 300V Art. 970483301
EasiGlide 330V Art. 970483401
EasiGlide 360V Art. 970483501

EG300VUK-20.960.01.indd 1 07.10.20 13:20

Fold-out Page width 5 mm less: 205 mm

A1

O1

-

2

1

3

q

A2

6

O2

w

1

5

4

-

8

:

7

q

A3

O3

z

u

1

9

4

0

O4

z

r

e

t

O5

O7 O8

a

s

t

z

t r

O6

i

r

e

5

O9

d

a

2

EG300VUK-20.960.01.indd 2 07.10.20 13:20

Fold-out Page width 5 mm less: 205 mm

O10 O11 M1

t

oru

M2

p

S3

6

4

S1

1 1

S4

1

6

:

S2

:

q

:

4

1

:

3

EG300VUK-20.960.01.indd 3 07.10.20 13:20

Page 2 width 2 mm less: 208 mm

EN Electric Hover Lawnmower

1. SAFETY ...............................................4

2. ASSEMBLY ............................................5

3. OPERATION ............................................5

4. MAINTENANCE .........................................6

5. STORAGE .............................................6

6. TROUBLESHOOTING ....................................6

7. TECHNICAL DATA .......................................7

8. ACCESSORIES .........................................7

9. SERVICE / WARRANTY ....................................7

Original instructions.

This product may be used under super-

vision, or if instruction regarding the safe
use of the product has been provided and the
resulting dangers have been understood, by chil­dren aged 8 and above, as well as by persons
with physical, sensory or mental disabilities or
alack of experience and knowledge. Children
must not be allowed to play with the product.
Cleaning and user maintenance must not be
performed by children without supervision.
The use of this product by young people under
the age of 16 is not recommended.

Cables

If extension cables are used, these must comply with the minimum cross­sections in the table below:

Voltage Cable length Cross section

220 – 240 V / 50 Hz Up to 40 m 1.0 mm²

220 – 240 V / 50 Hz Up to 60 m 1.5 mm²

220 – 240 V / 50 Hz Up to 100 m 2.5 mm²
Minimum rating: 1.0 mm² size cable, 10 amps 250 volts AC.

Your product is supplied with cable wired directly into the product.

1. If the supply cord is damaged, it must be replaced by your local Husqvarna
UK Ltd. Approved Service Centre or similarly qualified persons in order to
avoid ahazard.

2. Do not wire an extension cable directly to your product yourself. Please
contact your local Husqvarna UK Ltd. Approved Service Centre for further
information on the connectors and kits available.

3. Only use extension cables specifically designed for outdoor use and which
conform to one of the following specifications: Ordinary rubber (60245 IEC 53),
Ordinary PVC (60227 IEC 53) or Ordinary PCP (60245 IEC 57).

Training

a) Read the instructions carefully. Be familiar with the controls and the correct

use of the machine.

b) Never allow children or people unfamiliar with these instructions to use the

machine. Local regulations can restrict the age of the operator.

c) Never operate the machine while people, especially children, or pets are

nearby.

d) Keep in mind that the operator or user is responsible for accidents or hazards

occurring to other people or their property.

Intended use:

The FLYMO Lawnmower is intended to mow lawn in private domestic
gardens and allotments.

The product is not intended for long term use.

DANGER! Risk of injury!

v Do not use the product to cut bushes, hedges, shrubs, to cut

ofclimbers or grass on roofs or balcony boxes, to chop up
branches, twigs and to level irregularities in the soil. Do not
usethe product on a slope steeper than 20° maximum.

1. SAFETY

IMPORTANT!
Read the operator’s manual carefully before use and keep for future
reference.

Symbols on the product:

Read operator’s manual.

Keep bystanders away.

Beware of sharp blades. Blades continue to rotate

after the motor is switched off. Remove plug from
mains before maintenance or if cord is damaged.

Keep the mains cable away from the cutting blades.

General safety warnings

Electrical safety

DANGER! Electric shock!

Risk of injury due to electric shock.

v The product must be supplied through a residual current device (RCD)

having a rated residual operating current not exceeding 30 mA.

WARNING! Risk of physical injury!

Cut injury when the blade turns or the product starts accidentally.

v Disconnect the product from the mains before you do maintenance or

you replace parts. Thereby the disconnected socket must be in the
visual range.

Preparation

a) While operating the machine always wear substantial footwear and long

trousers. Do not operate the machine when barefoot or wearing open san­dals. Avoid wearing clothing that is loose fitting or that hanging cords or ties.

b) Thoroughly inspect the area where the machine is to be used and remove all

objects which can be thrown by the machine.

c) Before using, always visually inspect to see that the blade, blade bolt and the

blade assembly are not worn or damaged. Replace worn or damaged com­ponents in set to preserve balance. Replace damaged or unreadable labels.

d) Before use check the supply and extension cord for signs of damage or

aging. If the cord becomes damaged during use, disconnect the cord from
the supply immediately.
DO NOT TOUCH THE CORD BEFORE DISCONNECTING THE SUPPLY.
Do not use the machine if the cord is damaged or worn.

Operation

a) Operate the machine only in daylight or in good artificial light.
b) Avoid operating the machine in wet grass.
c) Always be sure of your footing on slopes.
d) Walk, never run.
e) Mow across the face of slopes, never up and down.
f) Exercise extreme caution when changing direction on slopes.
g) Do not mow excessively steep slopes.
h) Use extreme caution when reversing or pulling the machine towards you.
i) Stop the blade(s) if the machine has to be tilted for transportation when cross-

ing surfaces other than grass, and when transporting the machine to and from
area to be used.

j) Never operate the machine with defective guards or shields, or without safety

devices, for example deflectors and / or grass collector, in place.

k) Switch on the motor carefully according to instructions and with feet well

away from the blade(s).

l) Do not tilt the machine when switching on the motor, except if the machine

has to be tilted for starting. In this case, do not tilt it more than absolutely
necessary and lift only the part, which is away from the operator.

m) Do not start the machine when standing in front of the discharge opening.
n) Do not put hands or feet near or under rotating parts. Keep clear of the

discharge opening at all times.

o) Do not transport the machine while the power source is running.

) Stop the machine, and remove plug from the socket. Make sure that all

p

1

moving parts have come to a complete stop.

– whenever you leave the machine,
– before clearing blockages or unclogging chute,
– before checking, cleaning or working on the machine,
– after striking a foreign object. Inspect the machine for damage and make

repairs before restarting and operating the machine;

if the machine starts to vibrate abnormally (check immediately)
– inspect for damage,
– replace or repair any damaged parts,
– check for and tighten any loose parts.

4

EG300VUK-20.960.01.indd 4 07.10.20 13:20

Maintenance and storage

a) Keep all nuts, bolts, and screws tight to be sure the machine is in safe work-

ing condition.
b) Check the grass collector frequently for wear or deterioration.
c) Replace worn or damaged parts for safety.
d) On machines with multi blade, take care as rotating one blade can cause

other blades rotate.
e) Be careful during adjustment of the machine to prevent entrapment of the

fingers between moving blades and fixed parts of the machine.
f) Always allow the machine to cool down before storing.
g) When servicing the blades be aware that, even though the power source is

switched off, the blades can still be moved.
h) Use only genuine replacement parts and accessories.

Additional safety warnings

Electrical safety

DANGER! Cardiac arrest!

This product makes an electromagnetic field while it operates. This field
may under some conditions interfere with active or passive medical
implants. To decrease the risk of conditions that can possibly injure or
kill, we recommend persons with medical implants to speak with their
physician and the medical implant manufacturer before you operate the
product.

Before use, examine the cable for signs of damage or ageing. If the cable is
found to be defective, take the product to an authorised Service Centre and
have the cable replaced.

Do not use the product if the electric cables are damaged or worn.
Immediately disconnect from the mains if the cable is cut, or the insulation is

damaged. Do not touch the electric cable until the cable has been disconnected.
Do not repair a cut or damaged cable. Replace it with a new one.

The extension cable must be uncoiled. Coiled cables can overheat and reduce
the efficiency of your mower.

Keep the extension cable away from product, always work away from the power
point mowing up and down, never in circles.

Do not pull cable around sharp objects.
Always switch off at the mains before disconnecting any plug, cable connector or

extension cable.
Stop the motor, disconnect the mains and examine the cable for damage or

ageing before you wind the cable for storage. Do not repair a damaged cable,
replace it with a new one. Use only genuine replacement cable.

Always wind the cable carefully, avoid kinking.
Do not carry the product by the cable.
Do not pull on the cable to disconnect any of the plugs.
Use only on AC mains supply voltage shown on the product rating label.
Our products are double insulated to EN60335. Do not connect an earth to any

part of the product.
Check the working area for hidden cables.
Do not use for pond care or close to water.

Personal safety

DANGER! Risk of suffocation!

Small parts can be easily swallowed. There is also a risk that the polybag
can suffocate toddlers. Keep toddlers away when you assemble the
product.

Let the hover mower to cool down for at least 30 minutes before storage or
maintenance.

If blockage of cutting element stop product and check.
Do not tilt the machine into the direction of the user.
Do not move backwards.
Stay alert during operation.
Do not use in explosive atmosphere.
Do not operate the product when you are tired, ill or under the influence of

alcohol, drugs or medicine or you exhausted.
Do not overload the mower.
Use gloves, wear slip resistant shoes and wear eye protection.
Do not use under wet conditions.
Do not use on wet grass.
Do not disassemble the product further than the delivery status.
Only start the mower with an upright standing handle.
Do not use the start levers alternately.
Use the handles carefully.

Safety Cut-Out

The motor is protected by a Safety Cut-Out which is activated when the blade
becomes jammed or if the motor is overloaded. When this occurs, stop and dis­connect the product from the mains. The Safety Cut-Out will only reset when
you release the start / stop lever. Clear any obstruction and wait for a few minutes
for the Safety Cut-Out to reset before you continue to use the product.

2. ASSEMBLY

DANGER! Risk of injury!

Cut injury when the product starts accidentally.

v Wait for the blade to stop, disconnect the product from the

mains and use gloves before you assemble the product.

To assemble the lower handle [ Fig. A1 ]:

1. Place the end of the lower handle

2. Secure the lower handles

1

into the slots on the deck 2.

1

to the deck 2 by firmly pushing fixing

pin 3 through the holes in the deck 2 and handle 1.

3. Repeat on the other side.

NOTE: Should a problem occur when securing the handle to the deck
with the fixing pin, carefully lever fixing pin out of location and repeat steps
1 to 3 above.

To assemble the upper handle [ Fig. A2 / A3 ]:

1. Make sure that the upper handle

is located correctly with the safety

4

lock-off button 5 on the switchbox facing upwards.

2. Make sure that the upper handle

and the lower handle 1 are aligned

4

correctly.

3.

Insert the nut into the handle knob

4. Fit the bolts

, the washers 7, the handle knob 6 and the mains

8

(if necessary).

6

cable hooks * : onto the handles 1 / 4 in the correct positions.

* The mains cable hooks

5. Attach the cable

9

are selected models only.

:

to the handles 1 / 4 with the clips 0 provided.
Make sure that the cable 9 is not trapped between the upper
handle 4 and lower handle 1.

3. OPERATION

DANGER! Risk of injury!

Cut injury when the product starts accidentally.

v Wait for the blade to stop, disconnect the product from

the mains and use gloves before you adjust or transport
the product.

To connect the mower [ Fig. O1 / O2 ]:

DANGER! Electric shock!

To avoid damage to the mains cable

must be inserted into the cable lock -.

v Before you operate insert the mains cable

lock -.

1. Form a loop in the mains cable q, insert the loop into the cable lock ­slot in the switchbox w and pull tight.

2. Connect the mains cable

into a 230 V mains socket.

q

To adjust the cutting height [ Fig. O3 / O4 / O5 ]:

CAUTION! Do not use more than 3 cutting height spac­ers

. The cutting height spacers e must only be fitted between

e

the blade r and the fan t. Do not fit the cutting height spacers

between the blade r and the blade bolt z.

e

1. To remove the blade bolt z, hold the fan t firmly and loosen the blade
bolt z with the spanner u provided.

2. Remove the blade bolt

, the blade r, the cutting height spacers e

z

and the fan t.

3. Inspect for damage and clean as necessary.

4. Put the fan

on the product.

t

Make sure that the fan t is fully in place and the hole of the fan is inline
up with the threaded hole.

5. Put the cutting height spacers

onto the fan t.

e

Higher Cut – less cutting height spacers
Lower Cut – more cutting height spacers

Make sure that the pegs have located into the holes.

6. Put the blade

on by aligning the D-shaped holes onto the cutting

r

height spacers e.

Make sure that the pegs have located into the holes on the blade.

7. Put the blade bolt

8. Tighten down the blade bolt

9. Hold the fan

through the centre hole of the blade r.

z

clockwise by hand.

z

firmly and tighten the blade bolt z with the spanner u

t

provided.

, the mains cable q

q

into the cable

q

5

EG300VUK-20.960.01.indd 5 07.10.20 13:20

Operation position:

Adjustment is not required to move the handle to the operating position.
Simply pull down from the forward position or lift up from the down posi­tion until the handle is in the most comfortable operating position.

To start the mower [ Fig. O6 / O7 ]:

DANGER! Risk of injury!

Risk of injury if the product does not stop when you

release the start levers.

v Do not bypass the safety devices or switches. For example do

not attach the start levers to the handle.

To start:

The product is provided with a two-handed safety device (start
lever

and safety lock-off button 5) to prevent the product from

i

being turned on by accident.

There are two start levers

1. Push the safety lock-off button
lever i with the other hand.

The mower starts.

2. Release the safety lock-off button

To prevent a ring being cut in the lawn and to clear any residual grass, tilt
the mower slightly. When the lawnmower has reached full speed gently
lower it onto the lawn.

fitted. Either one has to be used to start.

i

with one hand and pull the start

5

.

5

To clean the mower:

DANGER! Risk of injury!

Risk of injury and risk of damage to the product.

v Do not clean the product with water or with a water jet

(in particular high-pressure water jet).

v Do not clean with chemicals including petrol or solvents.

Some can destroy critical plastic parts.

The airflow slots must always be clean.

To clean the underside of the mower [ Fig. M1 ]:

The underside is easiest to clean after you mowed.

1. Lay the mower on its side carefully.

2. Clean the underside
spanner / scraper tool u.

3. Clean the blade
sharp objects).

To clean the outside of the mower [ Fig. M2 ]:

1. Clean the outside with a dry cloth.

2. Clean the airflow slots

by removing any grass build up with the

o

and the fan t with a soft brush (do not use

r

with a soft brush (do not use sharp objects).

p

5. STORAGE

To stop:

v Release the start lever

The mower stops.

To empty the grass box [ Fig. O8 / O9 ]:

DANGER! Risk of physical injury!

Cut injury when the blade turns or the product starts

accidentally.

v Wait for the blade to stop, disconnect the product from the

mains and use gloves before you put /remove the grass box.

Models with a transparent window
grass box s. This should be cleaned after every lawn mowing.

1. Push in the lid

2. Remove the grass box
and rear of the grass box s.

3. Empty the grass box

4. Replace the grass box
deck fixing locations.

5. Close the lid

Failure to fit the grass box
poor collection of grass clippings.

Tips to use the mower [ Fig. O10 / O11 ]:

Mow twice a week during the growing season.

The lawn will suffer if more than a third of its length is cut at one time
and this may also result in poor collection.

For the best results mow the outside edge of the lawn in a clockwise
direction first.

Start to mow the edge of the lawn nearest to the power point.

So the cable is laid out on the lawn you have already cut.

For best grass collection always mow in a straight line. Do not swing the
lawnmower from side to side.

For the best cutting results mow in straight lines with an overlap of approx­imately 8 – 10 cm on each pass with the mower.

Do not overload the mower. To mow long thick grass may cause the
motor speed to drop and you will hear a change in the motor sound.
If the motor speed drops you may overload the mower which may cause
damage. When you mow in long thick grass a first cut with the cutting
height set higher will help reduce the load.
See To adjust the cutting height.

a

.

a

.

i

in the lid shows the filling level of the

d

where indicated and open the lid a.

by the moulded handle recesses at the front

s

.

s

. Make sure that it locates securely onto the

s

and the grass box lid a correctly can cause

s

4. MAINTENANCE

DANGER! Risk of injury!

Cut injury when the product starts accidentally.

v Wait for the blade to stop, disconnect the product from the

mains and use gloves before you maintain the product.

To put into storage:

The product must be stored away from children.

1. Disconnect the product from the mains.

2. Clean the mower (see 4. MAINTENANCE).

3. Store the mower in a dry, enclosed and frost-free place.

Storage positions [ Fig. S1 / S2 ]:

1. Push the lower handle

2. Rotate the handle
folding storage position or backward for the wall mounting storage
position.

3. Loosen the handle knob
upper handle 4.

Make sure that the cable is not locked between the lower and the
upper handle.

4. Wrap the mains cable

Folding storage position [ Fig. S3 ]:

Wall mounting storage position [ Fig. S4 ]:

NOTE: When wall-mounting storage, always hang the mower from
the lower handle

Disposal:

(in accordance with RL2012/19/EC)

The product must not be disposed of to normal household
waste. It must be disposed of in line with local environmental
regulations.

IMPORTANT!

v Dispose of the product through or via your municipal recycling collection

centre.

1

inwards from both sides simultaneously.

1

to the desired position, either forward for the

1

and the mains cable hook : and fold the

6

securely around the mains cable hooks :.

q

cross section.

6. TROUBLESHOOTING

DANGER! Risk of injury!

Cut injury when the product starts accidentally.

v Wait for the blade to stop, disconnect the product from the

mains and use gloves before you troubleshoot the product.

To replace the blade:

DANGER! Risk of injury!

Cut injury when the blade turns and it is damaged, bent,

out of balance or has chipped edges.

v Do not use the mower when the blade is damaged, bent,

out of balance or has chipped edges.

v Do not regrind the blade.

The FLYMO spare parts are available from your FLYMO dealer or from the
FLYMO service.

6

EG300VUK-20.960.01.indd 6 07.10.20 13:20

Only use an original FLYMO blade:

FLYMO Replacement Blade for 30 cm:
Reference no. FLY094 Part no. 529370590

FLYMO Replacement Blade for 33 cm:
Reference no. FLY095 Part no. 529370790

FLYMO Replacement Blade for 36 cm:
Reference no. FLY096 Part no. 529370890

v Replace the blade (see 3. OPERATION To adjust the cutting height).

Problem Possible Cause Remedy

Mower does not start Mains cable is disconnected

Motor is jammed and
makes a noise

Loud noises, the mower
is rattling

Mower runs unevenly or
vibrates strongly

Poor grass collection Lid is not correct in place. v Put the lid correct on the

Lawn is not cleanly mowed Blade is blunt or damaged. v Replace the blade.

Poor flotation Underside of the mower is

NOTE: For any other malfunctions please contact the FLYMO service depart­ment. Repairs must only be done by FLYMO service departments or specialist
dealers approved by FLYMO.

or damaged.

Motor is blocked. v Remove the obstacle.

Motor is blocked. v Remove the obstacle.

Cutting height is too low. v Raise the cutting height.

Screws on motor, its fixing or
onthe mower chasing are
loose.

Blade is damaged / worn or the
blade mounting is released.

Blade is very dirty. v Clean the mower

Airflow slots are dirty. v Clean the mower

Not mowing in straight lines. v Mow in straight lines.

Cutting height is too low. v Raise the cutting height.

dirty.

Cutting height is too low. v Raise the cutting height.

Fan is damaged. v Check and replace the fan.

If poor flotation persists, contact the local approved Service
Centre.

v Connect the mains cable or

if necessary replace it.

v Let the screws be tightened

by an authorised specialist
dealer.

v Replace the blade.

(see 4. MAINTENANCE).
If this does not rectify the
problem, replace the blade.

grass box.

(see 4. MAINTENANCE).

v Clean the underside of the

mower.

7. TECHNICAL DATA

Electric Hover Lawnmower

Rated power W 1700 1700 1800

Mains voltage V 230 230 230

Mains frequency Hz 50 50 50

Speed of rotation cutting
blade

Cutting width cm 30 33 36

Cutting height adjustment
(4 positions)

Volume of grass box l 20 20 30

Weight kg 8.2 8.2 8.4

Sound pressure level L
Uncertainty k

Sound power level L
measured / guaranteed
Uncertainty k

Hand / arm vibration a
Uncertainty k

Measuring process complying with:

exposure. The vibration emission value can vary during actual use of the electric power
tool.

pA

WA

vhw

NOTE: The stated vibration emission value has been measured according to
astandardised test procedure and can be used for comparison of one electric
power tool with another. It can also be used for preliminary evaluation of

Unit Value

R/min 4200 4200 4200

mm 10 – 30 10 – 30 10 – 30

1)

pA

dB (A)

2)

:

WA

dB (A)

1)

vhw

m/s

(30 cm)

84
3

92 / 96

3.9

1.5

2

1.5

1)

EN 60335-2-77

Value
(33 cm)

83
3

92 / 96

3.2

1.5

1.5

2)

RL 2000/14/EC

Value
(36 cm)

80
3

92 / 96

3.2

1.9

1.5

Please consult the supply authority, if necessary, that the equipment is
connected only to a supply of an impedance no more than 0.354Ω.

This maximum permissible system impedance at the interface point of
the user’s supply is according to the test value of EasiGlide 360V.

8. ACCESSORIES

FLYMO Replacement
Blade for 30 cm

FLYMO Replacement
Blade for 33 cm

FLYMO Replacement
Blade for 36 cm

As replacement for blunt blade. Reference no. FLY094

Part no. 529370590

As replacement for blunt blade. Reference no. FLY095

Part no. 529370790

As replacement for blunt blade. Reference no. FLY096

Part no. 529370890

9. SERVICE / WARRANTY

Service:

Please contact the address on the back page.

Warranty statement:

In the event of a warranty claim, no charge is levied to you for the services
provided.

FLYMO grants a warranty for all original FLYMO new products for two
years from the date of original purchase from the retailer, provided that
the devices have been for private use only. This manufacturer’s warranty
does not apply to products acquired second hand. This warranty includes
all significant defects of the product that can be proved to be material or
manufacturing faults. This war ranty is fulfilled by supplying afully functional
replacement product or by repairing the faulty product sent to us free of
charge; we reserve the right to choose between these options. This ser­vice is subject to the following provisions:

• The product has been used for its intended purpose as per the recom-

mendations in the operating instructions.

• Neither the purchaser nor a third party has attempted to open or repair

the product.

• Only Original FLYMO replacement parts and wear parts have been used

for operation.

• Presentation of the receipt.

Normal wear and tear of parts and components (such as blades, blade
fixing parts, turbines, light bulbs, V-belts / toothed belts, impellers, air
filters, spark plugs), visual changes, wear parts and consumables are
excluded from the warranty.

This manufacturer’s warranty is limited to replacement and repair of prod­ucts in accordance with the abovementioned conditions. The manufac­turer’s warranty does not constitute an entitlement to lodge other claims
against us as a manufacturer, such as for damages. This manufacturer’s
warranty does not, of course, affect statutory and contractual warranty
claims against the dealer / retailer.

The manufacturer’s warranty is governed by the law of the Federal
Republic of Germany.

In case of a warranty claim, please return the faulty product, together with
a copy of the receipt and a description of the fault, with postage paid to
the service address.

Consumables:

The blade is a consumable and is not included in the warranty.

7

EG300VUK-20.960.01.indd 7 07.10.20 13:20

PRODUCT LIABILITY

In accordance with the German Product Liability Act, we hereby expressly declare that we accept no liability for damage incurred from our products
where said products have not been properly repaired by a FLYMO-approved service partner or where original FLYMO parts or parts authorised by
FLYMO were not used.

EC DECLARATION OF CONFORMITY

The undersigned hereby certifies as the authorised representative of the manufacturer, Husqvarna AB, 561 82 Huskvarna, Sweden, that, when leaving
our factory, the unit(s) indicated below is / are in accordance with the harmonised EU guidelines, EU standards of safety and product specific standards.
This certificate becomes void if the unit(s) is / are modified without our approval.

Description of the product: Electric Hover Lawnmower

Product type EasiGlide 300

Article-Number 970483001

EC-Directives 2006/42/EC

Harmonised EN EN ISO 12100

Deposited Documentation GARDENA Technical Documentation,

Conformity Assessment according to 2000/14/EC Procedure: art. 14 Annex VI

Noise level: measured / guaranteed 92 dB (A) / 96 dB (A)

Year of EC marking: 2020

Ulm, 12.12.2020

Authorised representative:

EasiGlide 330
EasiGlide 360

EasiGlide 300V
EasiGlide 330V
EasiGlide 360V

970483101
970483201

970483301
970483401
970483501

2014/30/EC
2000/14/EC
2011/65/EC

EN 60335-1
EN 60335-2-77

M. Kugler, 89079 Ulm

John Thompson

Product and Marketing Director EUAP

8

EG300VUK-20.960.01.indd 8 07.10.20 13:20

9

EG300VUK-20.960.01.indd 9 07.10.20 13:20

Deutschland / Germany

GARDENA Manufacturing GmbH
Central Service
Hans-Lorenser-Straße 40
D-89079 Ulm
Produktfragen:
([phone]
Reparaturen:
([phone]
[e-mail]

Albania

COBALT Sh.p.k.
Rr. Siri Kodra
1000 Tirana

Argentina

Husqvarna Argentina S.A.
Av.del Libertador 5954 –
Piso 11 – Torre B
(C1428ARP) Buenos Aires
Phone: [phone]
[e-mail]

Armenia

Garden Land Ltd.
61 Tigran Mets
0005 Yerevan

Australia

Husqvarna Australia Pty. Ltd.
Locked Bag 5
Central Coast BC
NSW 2252
Phone: (+ 61) (0) 2 4352 7400
customer.service@
husqvarna.com.au

Austria / Österreich

Husqvarna Austria GmbH
Industriezeile 36
4010 Linz
Tel. : [phone]
service.gardena@
husqvarnagroup.com

Azerbaijan

Firm Progress
a. Aliyev Str. 26A
1052 Baku

Belgium

Husqvarna België nv/sa
Gardena Division
Rue Egide Van Ophem 111
1180 Uc cle / Ukkel
Tel.: [phone]
Mail: [e-mail]

Bosnia / Herzegovina

SILK TRADE d.o.o.
Industrijska zona Bukva bb
74260 Tešanj

Brazil

Husqvarna do Brasil Ltda
Av. Francisco Matarazzo,

o

1400 – 19
São Paulo – SP

andar

CEP: 05001-903
Tel: [phone]
marketing.br.husqvarna@
husqvarna.com.br

Bulgaria

AGROLAND България АД
бул. 8 Декември, № 13
Офис 5
1700 Студентски град
София
Тел.: [phone]
[e-mail]

Canada / USA

GARDENA Canada Ltd.
100 Summerlea Road
Brampton, Ontario L6T 4X3
Phone: [phone]
[e-mail]

Chile

Maquinarias Agroforestales
Ltda. (Maga Ltda.)
Santiago, Chile
Avda. Chesterton
# 8355 comuna Las Condes
Phone: [phone]
[e-mail]
Zipcode: 7560330

China

Husqvarna (China) Machinery
Manufacturing Co., Ltd.
No. 1355, Jia Xin Rd.,
Ma Lu Zhen, Jia Ding Dist.,
Shanghai
201801
Phone: [phone]
Domestic Sales
www.gardena.com.cn

Colombia

Husqvarna Colombia S.A.
Calle 18 No. 68 D-31, zona
Industrial de Montevideo
Bogotá, Cundinamarca
Tel. [phone] ext. 105
[e-mail]

Costa Rica

Compania Exim
Euroiberoamericana S.A.
Los Colegios, Moravia,
200 metros al Sur del Colegio
Saint Francis – San José
Phone: [phone]
[e-mail]

Croatia

SILK ADRIA d.o.o.
Josipa Lončara 3
10090 Zagreb
Phone: [phone]
[e-mail]

Cyprus

Med Marketing
17 Digeni Akrita Ave
P.O. Box 27017
1641 Nicosia

Czech Republic

Husqvarna Česko s.r.o.
Türkova 2319/5b
149 00 Praha 4 – Chodov
Bezplatná infolinka :
800 100 425
[e-mail]

Denmark

GARDENA DANMARK
Lejrvej 19, st.
3500 Værløse
Tlf.: (+45 ) 7 0 26 47 70
[e-mail]
www.gardena.com / dk

Dominican Republic

BOSQUESA, S.R.L
Carretera Santiago Licey
Km. 5 ½
Esquina Copal II.
Santiago
Dominican Republic
Phone: [phone]
[e-mail]

Ecuador

Husqvarna Ecuador S.A.
Arupos E1-181 y 10 de
Agosto Quito, Pichincha
Tel. [phone]
francisco.jacome@
husqvarna.com.ec

Estonia

Husqvarna Eesti OÜ
Gardena Division
Valdeku 132
Tallinn
11216, Estonia
[e-mail]

Finland

Oy Husqvarna Ab
Gardena Division
Lautatarhankatu 8 B /PL 3
00581 HELSINKI
[e-mail]

France

Husqvarna France
9/11 Allée des pierres mayettes
92635 Gennevilliers Cedex
France
http : //www.gardena.com/ fr
N° AZUR: 0 810 00 78 23
(Prix d’un appel local)

Georgia

ALD Group
Beliashvili 8
1159 Tleilisi

Great Britain

Husqvarna UK Ltd
Preston Road
Aycliffe Industrial Park
Newton Aycliffe
County Durham
DL5 6UP
Phone:[phone]
customer.services@
husqvarna.co.uk

Greece

Π.ΠΑΠΑΔΟΠΟΥΛΟΣ ΑΕΒΕ
Λεωφ. Αθηνών 92
Αθήνα
Τ.Κ.1 04 4 2
Ελλάδα
Τηλ. ([phone]
[e-mail]

100

Hungary

Husqvarna Magyarország Kft.
Ezred u. 1 - 3
1044 Budapest
Telefon: [phone]
vevoszolgalat.husqvarna@
husqvarna.hu

Iceland

Ó. Johnson & Kaaber
Tunguhalsi 1
110 Reykjavik
[e-mail]

Ireland

Husqvarna UK Ltd
Preston Road
Aycliffe Industrial Park
Newton Aycliffe
County Durham
DL5 6UP
i

[e-mail]

Italy

Husqvarna Italia S.p.A.
Via Santa Vecchia 15
23868 VALMADRERA (LC)
Phone: [phone]
assistenza.italia@
it.husqvarna.com

Japan

KAKUICHI Co. Ltd.
Sumitomo Realty &
Development Kojimachi
BLDG., 8F
5 -1 Nibanncyo
Chiyoda-ku
Tokyo 102-0084
Phone: [phone]
[e-mail]

Kazakhstan

LAMED Ltd.
155/1, Tazhibayevoi Str.
050060 Almaty
IP Schmidt
Abayavenue 3B
110 005 Kostanay

Korea

Kyung Jin Trading CO.,LTD.
107-4, SunDuk Bld.,
YangJae-dong,
Seocho-gu,
Seoul, (zipcode: 137-891)
Phone: (+82) (0)2 574-6300

Kyrgyzstan

Alye Maki
av. Moladaya Guardir J 3
720014
Bishkek

Latvia

Husqvarna Latvija SIA
Gardena Division
Ulbrokas 19A
LV-1021 Rīga
[e-mail]

Lithuania

UAB Husqvarna Lietuva
Gardena Division
Ateities pl. 77C
LT-52104 Kaunas
[e-mail]

Luxembourg

Magasins Jules Neuberg
39, rue Jacques Stas
Luxembourg-Gasperich 2549
Case Postale No. 12
Luxembourg 2010
Phone: [phone]
[e-mail]

Mexico

AFOSA
Av. Lopez Mateos Sur # 5019
Col. La Calma 45070
Zapopan, Jalisco, Mexico
Phone: [phone]
[e-mail]

Moldova

Convel S.R.L.
290A Muncesti Str.
2002 Chisinau

Netherlands

Husqvarna Nederland B.V.
GARDENA Division
Postbus 50131
1305 AC ALMERE
Phone: [phone]
[e-mail]

Neth. Antilles

Jonka Enterprises N.V.
Sta. Rosa Weg 196
P.O. Box 8200
Curaçao
Phone: [phone]
[e-mail]

New Zealand

Husqvarna New Zealand Ltd.
PO Box 76-437
Manukau City 2241
Phone: (+64) (0) 9 9202410
[e-mail]

Norway

Husqvarna Norge AS
Gardena Division
Trøskenveien 36
1708 Sarpsborg
Tel: [phone]
www.gardena.no

Peru

Husqvarna Perú S.A.
Jr. Ramón Cárcamo 710
Lima 1
Tel: [phone] ext. 416
[e-mail]

Poland

Husqvarna
Poland Spółka z o.o.
ul. Wysockiego 15 b
03-371 Warszawa
Phone: [phone]
[e-mail]

Portugal

Husqvarna Portugal, SA
Lagoa - Albarraque
2635 - 595 Rio de Mouro
Tel.: [phone]
Fax : [phone]
[e-mail]

Romania

Madex International Srl
Soseau a O daii 117 - 123,
RO 013603 Bucureşti, S1
Phone: [phone]
[e-mail]

Russia / Россия

ООО „Хускварна“
14140 0, М осков ск ая обл .,
г. Химки,
улица Ленинградская,
владение 39, стр.6
Бизнес Центр
„Химки Бизнес Парк“,
помещение ОВ02_04
http://www.gardena.ru

Serbia

Domel d.o.o.
Autoput za Novi Sad bb
11273 Belgrade
Phone: [phone]
[e-mail]

Singapore

Hy-Ray PRIVATE LIMITED
40 Jalan Pemimpin
#02-08 Tat Ann Building
Singapore 577185
Phone: [phone]
[e-mail]

Slovak Republic

Husqvarna Česko s.r.o.
Türkova 2319/5b
149 00 Praha 4 – Chodov
Bezplatná infolinka:
800 154 044
[e-mail]

Slovenia

Husqvarna Austria GmbH
Industriezeile 36
4010 Linz
Tel.: [phone]
service.gardena@
husqvarnagroup.com

South Africa

Husqvarna
South Africa (Pty) Ltd
Postnet Suite 250
Private Bag X6,
Cascades, 3202
South Africa
Phone: [phone]
[e-mail]

Spain

Husqvarna España S.A.
Calle de Rivas nº 10
28052 Madrid
Phone: [phone]
[e-mail]

Suriname

Agrofix n.v.
Verlengde Hogestraat #22
Phone: [phone]
[e-mail]
Pobox : 2006
Paramaribo
Suriname – South America

Sweden

Husqvarna AB
Gardena Division
S-561 82 Huskvarna
[e-mail]

Switzerland / Schweiz

Husqvarna Schweiz AG
Consumer Products
Industriestrasse 10
5506 Mägenwil
Phone: (+ 41) (0) 62 887 37 90
[e-mail]

Tur key

GARDENA Dost Diş Ticaret
Mümessillik A.Ş.
Sanayi Çad. Adil Sokak
No: 1/B Kartal
34873 Istanbul
Phone: [phone]
[e-mail]

Ukraine / Україна

ТОВ « Хусварна Укра їна »
вул. Васильківська, 34,
офіс 204-г
03022, Київ
Тел. [phone]
[e-mail]

Uruguay

FELI SA
Entre Ríos 1083 CP 11800
Montevideo – Uruguay
Tel : [phone]
[e-mail]

Venezuela

Corporación Casa y Jardín C.A.
Av. Caroní, Edif. Trezmen, PB.
Colinas de Bello Monte.
1050 Caracas.
Tlf : ([phone]
[e-mail]

EG300VUK-20.960.01/1020
Husqvarna AB
S-561 82 Huskvarna
Sweden

Our polic y of continuo us improvemen t means that th e specifica tion of produ cts may be alt ered from time t o time withou t prior notic e.

®

and other product and feature names are registered or unregistered trademarks of Flymo S.A.

10

EG300VUK-20.960.01.indd 10 07.10.20 13:20

Flymo

Copyr ight © 2020 Flymo S. A. All rights re served.