Fluke TL1000/30M, TL1000 KIT User manual

TL1000-KIT

Test Leads

TL1000/30M

30 m Test Lead on Reel

Safety Information

A Warning identifies hazardous conditions and procedures that
are dangerous to the user. A Caution identifies conditions and
pro

cedures that can cause damage to the Product or the

equipment under test.

XW Warning

To prevent possible electrical shock, fire, or personal
injury:

 Read all safety information before you use the

Product.

 Use the Product only as specified, or the protection

supplied by the Product can be compromised.

 Carefully read all instructions.

PN 5341976 (English) 8/2022
©2022 Fluke Corporation. All rights reserved. Specifications are
subject to change without notice. All Product names are trademarks of
their respective companies.

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

 Comply with local and national safety codes. Use

personal protective equipment (approved rubber
gloves, face protection, and flame-resistant clothes)
to prevent shock and arc blast injury where hazardous
live conductors are exposed.

 Do not use in CAT III or CAT IV environments without

the protective cap (if included with the Product)
installed on test probe. The protective cap decreases
the exposed probe metal to <4 mm. This decreases the
possibility of arc flash from short circuits.

 Do not use a shrouded banana jack accessory such as

an alligator clip with an unshrouded 4 mm banana
probe tip terminal in a hazardous electrical
installation. Due to the lack of a shroud, the probe tip
connector does not provide suitable insulation to
accessible parts with this type of assembly.

 Use Product-approved measurement category (CAT),

voltage, and amperage rated accessories (probes,
test leads, and adapters) for all measurements.

 Do not touch voltages >30 V ac rms, 42 V ac peak, or

60 V dc.

 Do not use the Product around explosive gas, vapor,

or in damp or wet environments.

 Do not exceed the Measurement Category (CAT)

rating of the lowest rated individual component of a
Product, probe, or accessory.

 Do not use test leads if they are damaged. Examine the

test leads for damaged insulation, exposed metal, or if
the wear indicator (if present) shows. Check test lead
continuity.

 Keep fingers behind the finger guards on the probes.

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Symbols

The table below lists the symbols that can be used on the Product
or in this document.

Symbol Description

W

X

T

P Conforms to European Union directives.

¼

½

¾

~

WARNING. RISK OF DANGER.

WARNING. HAZARDOUS VOLTAGE. Risk of electric
shock.

Double insulated

Measurement Category II is applicable to test and
measuring circuits connected directly to utilization
points (socket outlets and similar points) of the low­voltage MAINS installation.

Measurement Category III is applicable to test and
measuring circuits connected to the distribution
part of the building’s low-voltage MAINS installation.

Measurement Category IV is applicable to test and
measuring circuits connected at the source of the
building’s low-voltage MAINS installation.

This product complies with the WEEE Directive and
its marking requirements. The affixed label indicates
that you must not discard this electrical/electronic
product in domestic household waste. Do not
dispose of this product as unsorted municipal
waste. For information about take-back and
recycling programs available in your country, see
the website.

Maintenance

Clean with a soft towel moistened with water and mild detergent.
DO NOT IMMERSE in liquid.

Specifications

Safety............................................IEC 61010-031, Pollution Degree 2

TL1000 Test Leads .............CAT III 1000 V, CAT IV 600 V, 10 A

TL1000/30M Test Lead .....CAT III 1000 V, CAT IV 600 V,

5 A (on reel) 10 A (fully extended)

TP74 Test Probes

with cap.............................CAT III 1000 V, CAT IV 600 V, 10 A

without cap ......................CAT II 1000 V, 10 A

AC285 Alligator Clips.........CAT III 1000 V, CAT IV 600 V, 10 A

Temperature................................-20 °C to 50 °C (-4 °F to 122 °F)

Humidity .......................................<95 % RH, up to 35 °C (95 °F)

Altitude .........................................2000 m

<40 % RH, 35 °C to 50 °C (95 °F to
122 °F)

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

LIMITED WARRANTY

This Fluke product will be free from defects in material and
workmanship for 1 year from the date of purchase. This warranty
does not cover fuses, disposable batteries, or damage from
accident, neglect, misuse, alteration, contamination, or abnormal
conditions of operation or handling. Resellers are not authorized
to extend any other warranty on Fluke’s behalf. To obtain service
during the warranty period, contact your nearest Fluke authorized
service center to obtain return authorization information, then
send the product to that Service Center with a description of the
problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER
WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR PURPOSE,
ARE EXPRESSED OR IMPLIED. FLUKE IS NOT LIABLE FOR ANY
SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR THEORY.
Since some states or countries do not allow the exclusion or
limitation of an implied warranty or of incidental or consequential
damages, this limitation of liability may not apply to you.

11/99

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com