Fluke TI401-PRO-60HZ, TI401-PRO-KIT, TIX501-60HZ, TI400-PRO-60HZ, Ti480-PRO 60 Hz User manual

Ti300 PRO, Ti400 PRO, Ti401 PRO,

Ti450 PRO, Ti480 PRO

Professional Series Thermal Imagers

Ti450 SF6

Gas Leak Detector

Users Manual



November 2017 Rev. 2, 4/19 (English)

© 2017-2019 Fluke Corporation. All rights reserved. Specifications are subject to change without notice.
All product names are trademarks of their respective companies.

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

LIMITED WARRANTY AND LIMITATION OF LIABILITY

LIMITED WARRANTY AND LIMITATION OF LIABILITY

Each Fluke product is warranted to be free from defects in material and workmanship under normal use and
service. The warranty period is two years and begins on the date of shipment. Parts, product repairs, and services
are warranted for 90 days. This warranty extends only to the original buyer or end-user customer of a Fluke
authorized reseller, and does not apply to fuses, disposable batteries, or to any product which, in Fluke's opinion,
has been misused, altered, neglected, contaminated, or damaged by accident or abnormal conditions of operation
or handling. Fluke warrants that software will operate substantially in accordance with its functional specifications
for 90 days and that it has been properly recorded on non-defective media. Fluke does not warrant that software
will be error free or operate without interruption.

Fluke authorized resellers shall extend this warranty on new and unused products to end-user customers only but
have no authority to extend a greater or different warranty on behalf of Fluke. Warranty support is available only if
product is purchased through a Fluke authorized sales outlet or Buyer has paid the applicable international price.
Fluke reserves the right to invoice Buyer for importation costs of repair/replacement parts when product purchased
in one country is submitted for repair in another country.

Fluke's warranty obligation is limited, at Fluke's option, to refund of the purchase price, free of charge repair, or
replacement of a defective product which is returned to a Fluke authorized service center within the warranty
period.

To obtain warranty service, contact your nearest Fluke authorized service center to obtain return authorization
information, then send the product to that service center, with a description of the difficulty, postage and insurance
prepaid (FOB Destination). Fluke assumes no risk for damage in transit. Following warranty repair, the product will
be returned to Buyer, transportation prepaid (FOB Destination). If Fluke determines that failure was caused by
neglect, misuse, contamination, alteration, accident, or abnormal condition of operation or handling, including
overvoltage failures caused by use outside the product’s specified rating, or normal wear and tear of mechanical
components, Fluke will provide an estimate of repair costs and obtain authorization before commencing the work.
Following repair, the product will be returned to the Buyer transportation prepaid and the Buyer will be billed for the
repair and return transportation charges (FOB Shipping Point).

THIS WARRANTY IS BUYER'S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. FLUKE SHALL NOT BE LIABLE FOR ANY
SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSE
DATA,

Since some countries or states do not allow limitation of the term of an implied warranty, or exclusion or limitation
of incidental or consequential damages, the limitations and exclusions of this warranty may not apply to every
buyer. If any provision of this Warranty is held invalid or unenforceable by a court or other decision-maker of
competent jurisdiction, such holding will not affect the validity or enforceability of any other provision.

ARISING

FROM ANY CAUSE OR THEORY.

S, INCLUDING LOSS OF

11/99

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Table of Contents

Title Page

Introduction ........................................................................................................... 1

Safety Information................................................

Product Familiarization ......................................................................................... 4

Features........................................................................................................... 4

Controls ........................................................................................................... 6

Touch Screen .................................................................................................. 8

Control Panel ................................................................................................... 9

Primary and Secondary Triggers ..................................................................... 9

Basic Operation .................................................................................................... 10

Turn On and Off the Imager............................................................................. 10

Focus ............................................................................................................... 10

Capture Image ................................................................................................. 10

Save Image...................................................................................................... 11

Menus ................................................................................................................... 11

Measurement Menu......................................................................................... 12

Level/Span.................................................................................................. 14

Emissivity Adjustment................................................................................. 15

Transmission .............................................................................................. 16

Spot Boxes ................................................................................................. 16

Spot Markers .............................................................................................. 17

Delta-T........................................................................................................ 17

Image Menu..................................................................................................... 18

Image Enhancement .................................................................................. 20

Distance...................................................................................................... 22

Camera Menu .................................................................................................. 23

LaserSharp Auto Focus System................................................................. 25

Video .......................................................................................................... 25

Wireless Connectivity ................................................................................. 26

Fluke Connect Wireless System...................................................................... 28

Fluke Connect App ..................................................................................... 28

Fluke Connect Tools................................................................................... 29

Memory Menu.................................................................................................. 30

Review Image............................................................................................. 30

Edit Image .................................................................................................. 30

Delete Image .............................................................................................. 32

Settings Menu.................................................................................................. 33

File Format ................................................................................................. 34

Date ............................................................................................................ 35

................................................. 2

i

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

Time ............................................................................................................ 35

SF6 Gas Detection Mode Menu....................................................................... 36

Gas Detection Conditions ........................................................................... 36

SmartView Software.............................................................................................. 38

Download SmartView Software........................................................................ 38

Download Firmware ......................................................................................... 38

Enable the Radio.............................................................................................. 39

Streaming Video (Remote Display) ....................................................................... 39

Stream Live to a PC ......................................................................................... 40

Stream Live with Fluke Connect Software ....................................................... 40

Stream Live to an HDMI Device ....................................................................... 40

Remote Control of Imager ..................................................................................... 41

Accessories ........................................................................................................... 41

Optional Lenses ............................................................................................... 42

Maintenance.......................................................................................................... 43

Clean the Case ................................................................................................ 43

Lens Care......................................................................................................... 43

Battery Care ..................................................................................................... 43

Charge Batteries .............................................................................................. 44

Two-Bay Battery Charger Base .................................................................. 44

AC Power Socket on Imager....................................................................... 44

Optional 12 V Vehicle Charger ................................................................... 45

Radio Frequency Data .......................................................................................... 45

General Specifications .......................................................................................... 45

Detailed Specifications .......................................................................................... 47

ii

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Introduction

The Fluke Ti300 PRO, Ti400 PRO, Ti401 PRO, Ti450 PRO, Ti450 SF6, and Ti480 PRO Professional Thermal
Imagers (the Product or Imager) are handheld, infrared imaging cameras for use in many applications. These
applications include equipment troubleshooting, preventive and predictive maintenance, building diagnostics,
research and development, and gas leak detection.

The Imager displays thermal images on a high-visibility, industrial-quality LCD touch screen. The Imager can
save images to internal memory, to a removable memory card, or to a USB storage device. Saved images and
data stored in internal memory or on the memory card can be transferred to a PC through a direct USB
connection to the PC or by wireless transfer to a PC or mobile device.

The Imager includes SmartView software. SmartView is a high-performance, professional software suite for
quality analysis and reporting. The Imager works with the Fluke Connect

A rugged, rechargeable lithium-ion smart battery provides power to the Imager. Direct ac power is accessible with
the included ac power adapter.



app available on mobile devices.

1

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

Safety Information

A Warning identifies hazardous conditions and procedures that are dangerous to the user. A Caution identifies
conditions and procedures that can cause damage to the Product or the equipment under test.

*W Warning

To prevent possible electrical shock, fire, or personal injury and for safe operation of the
Product:

• Read all safety information before you use the Product.

• Carefully read all instructions.

• Do not alter the Product and use only as specified, or the protection supplied by the Product
can be compromised.

• Replace the batteries when the low battery indicator shows to prevent incorrect
measurements.

• Do not use the Product if it operates incorrectly.

• Do not use the Product if it is altered or damaged.

• Disable the Product if it is damaged.

• See emissivity information for actual temperatures. Reflective objects result in lower than
actual temperature measurements. These objects can pose a burn hazard.

• Do not put battery cells and battery packs near heat or fire. Do not put in sunlight.

• Do not disassemble or crush battery cells and battery packs.

• Remove batteries to prevent battery leakage and damage to the Product if it is not used for an
extended period.

• Connect the battery charger to the mains power outlet before the charger.

• Use only Fluke approved power adapters to charge the battery.

• Keep cells and battery packs clean and dry. Clean dirty connectors with a dry, clean cloth.

• Batteries contain hazardous chemicals that can cause burns or explode. If exposure to
chemicals occurs, clean with water and get medical aid.

• Do not disassemble the battery.

• Repair the Product before use if the battery leaks.

• Use only the external mains power supply included with the Product.

• Do not put metal objects into connectors.

• Use only specified replacement parts.

• Have an approved technician repair the Product.

• Remove the batteries if the Product is not used for an extended period of time, or if stored in
temperatures above 50 °C. If the batteries are not removed, battery leakage can damage the
Product.

2

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Professional Series Thermal Imagers

Safety Information

• Disconnect the battery charger and move the Product or battery to a cool, non-flammable

location if the rechargeable battery becomes hot (>50 °C) during the charge period.

• Replace the rechargeable battery after 5 years of moderate use or 2 years of heavy use.

Moderate use is defined as recharged twice a week. Heavy use is defined as discharged to
cutoff and recharged daily.

• Do not short the battery terminals together.

• Do not keep cells or batteries in a container where the terminals can be shorted.

• Do not use the Product for medical reasons. The Product is intended for equipment evaluation

only and should never be used in diagnostics, treatment, or any other capacity where the
Product would come in contact with a patient.

W Caution

Storage and/or continual operation of the Imager in extreme ambient temperature conditions
can result in temporary interruption of operation. If this occurs, let the Imager stabilize (cool
down or warm up) before you resume operation.

Table 1 is a list of symbols that can be used on the Imager or in this manual.

Table 1. Symbols

Symbol Description



W

*

15V DC

"







™

MEMORY

HDMI

Consult user documentation.

WARNING. RISK OF DANGER.

WARNING. LASER RADIATION. Risk of eye damage.

Center positive power port.

Connected to ac power. Battery removed.

Battery.

Battery status. Battery charging when animated.

On/Off

Universal Serial Bus (USB) connection.

Memory card slot.

High-Definition Multimedia Interface (HDMI) connection.

P Conforms to European Union directives.

) Certified by CSA Group to North American safety standards.

 Conforms to relevant Australian Safety and EMC standards.

 Conforms to relevant South Korean EMC standards.

3

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

Table 1. Symbols (cont.)

Symbol Description





~

LASER

2

Conforms to the Appliance Efficiency Regulation (California Code of Regulations, Title 20,
Sections 1601 through 1608), for small battery charging systems.

Japan Quality Association

This Product contains a lithium-ion battery. Do not mix with the solid waste stream. Spent
batteries should be disposed of by a qualified recycler or hazardous materials handler per
local regulations. Contact your authorized Fluke Service Center for recycling information.

This product complies with the WEEE Directive marking requirements. The affixed label
indicates that you must not discard this electrical/electronic product in domestic household
waste. Product Category: With reference to the equipment types in the WEEE Directive
Annex I, this product is classed as category 9 "Monitoring and Control Instrumentation"
product. Do not dispose of this product as unsorted municipal waste.

Indicates a Class 2 laser. DO NOT STARE INTO BEAM The following text may appear
with the symbol on the product label: “IEC/EN 60825-1:2014. Complies with 21 CFR

1040.10 and 1040.11 except for deviations pursuant to Laser Notice 50, dated June 24,

2007.” In addition, the following pattern on the label will indicate wavelength and optical
power: λ = xxxnm, x.xxmW.

Product Familiarization

The manual explains features for multiple models. Because models have different features, not all of the
information in the manual may apply to your Imager. Use Table 2 to identify the features of your Imager.

Features

Table 2 lists the features of the Imager.

Table 2. Features

Feature

Focus/Image Enhancement

Advanced manual focus

LaserSharp Auto Focus System 

Filter mode 

MultiSharp Focus 

SuperResolution 

Digital Zoom

2X 

4X 

Ti300

PRO



Ti400

PRO



Ti401

PRO

Ti450

PRO

Ti450

SF6

Ti480

PRO

4

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Table 2. Features (cont.)

Professional Series Thermal Imagers

Product Familiarization

Feature

IR-Fusion Technology

Visible 

Picture-in-Picture (PIP) 

Full screen IR Autoblend (Preset
percentage selection)

Image annotations

IR-PhotoNotes 

Audio (Voice) 

Text 

Video mode  

Auto capture mode  

Spot Markers  

Wireless connectivity

WiFi 

Bluetooth

Fluke Connect 

HDMI connectivity 



Ti300

PRO





Ti400

PRO

Ti401

PRO

Ti450

PRO

Ti450

SF6

Ti480

PRO

SmartView software

Stream video (remote display) 

Remote operation of Imager 

Gas Leak Detection 

Relative Humidity and Temperature
Adjustment



5

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

Controls

Table 3 shows the connections of the Imager.

Table 3. Connections

3

2

4

5

7

F

G

H

I

6

Connector Cover

Lithium-ion Smart Battery

AC Power Supply with Universal
Adapters

2-Bay Battery Charging Base

1

9

8

Item Description Item Description







D

Micro SD Memory Card Slot

HDMI Connection

USB Cable Connection

USB Storage Device Connection

E

6

Find Quality Products Online at: [e-mail]

AC Adapter/Charger Input Terminal

www.GlobalTestSupply.com

Table 4 shows the front of the Product.

Ti450 PRO

IR FUSION

TECHNOLOGY

2

3

4

5

6

7

1

Professional Series Thermal Imagers

Product Familiarization

Table 4. Front

Item Description Item Description







D

LED Torch/Flashlight

Retractable Lens Cover

Visual Light Camera Lens

Laser Pointer/Distance Finder

E

F

G

Infrared Camera Lens

Secondary Trigger

Primary Trigger

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

7

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

Table 5 shows the back of the Product.

Table 5. Back

1

THERMAL
IMA

G

E

R

Ti200

Ti450 PRO

IR FUSION

IR FUSION

TECHNOLOGY

TECHNOLOGY

6

2

3

4

5

Item Description Item Description







Microphone

Speaker

LCD Touch Screen (display)

D

E

F

Control Panel

Hand Strap

Manual Focus

Touch Screen

The touch screen is a shortcut to the most used settings. To change parameters or select functions and options,
touch a target on the display.

The touch screen has a backlight for work in dimly lit spaces. When not in a menu, double tap on the display to
capture an image.

8

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Professional Series Thermal Imagers

Product Familiarization

Control Panel

The control panel is used to change parameters or select functions and options. Table 6 lists the functions of the
buttons on the Control Panel.

Table 6. Control Panel

Button Description









WXYZ

Push to turn On/Off.

Within a submenu, push to save the change and go back to the live view.

Push to open the primary menu.
Within a submenu:
Push to either save the change and go back to the previous menu.
Or
Push to perform the function listed on the submenu key.

Within a submenu:
Push to either cancel the change and go back to the live view.
Or
Push to perform the function listed on the submenu key.

Push to move the cursor and select an option.
In live Manual Mode, push to adjust Level and Span.

Primary and Secondary Triggers

The two-part trigger is located in the standard trigger position for a pistol-grip device. The larger, green trigger is
the primary trigger. The smaller, black trigger is the secondary trigger.

In normal operation (video is off), use the primary trigger to capture an image to save or edit. When video is on,
use the primary trigger to start/stop recording a video.

The secondary trigger operates the LaserSharp Auto Focus System (see LaserSharp Auto Focus System) and
the Laser Pointer/Distance Finder (see Distance).

9

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

Basic Operation

Turn On and Off the Imager

Before you use the Imager for the first time, charge the battery for a minimum of two and one-half hours. See

Charge Batteries.

To turn on or turn off the Imager, push and hold

To maximize the life of the battery, use the Power Save and Auto Off features. See Table 13 for more information
about how to set these features.

All thermal imagers need sufficient warm-up time for accurate temperature measurements and best
image quality. Warm-up time can vary by model and environmental conditions. Although most imagers
are fully warmed up in 3 minutes to 5 minutes, wait a minimum of 10 minutes if the most accurate
temperature measurement is important to your application. When you move an Imager between
environments with large differences in ambient temperature, allow for additional adjustment time.

Focus

Correct focus makes sure that the infrared energy is correctly directed onto the pixels of the detector. Without
correct focus, the thermal image can be blurry and the radiometric data may be inaccurate. Out-of-focus infrared
images are frequently unusable or of little value.

To focus with the advanced manual focus system, rotate the Manual Focus Control until the inspection object is
in proper focus. Use the advanced manual focus system as an override to the LaserSharp Auto Focus System.
See LaserSharp Auto Focus System.

 for 2 seconds.

Note

Capture Image

To capture an image:

1. Focus on a target.

2. Pull and release the Primary Trigger or double tap on the display to capture and freeze the image.

The image is in the memory buffer for you to save or edit the image. To edit an image, see Edit Image.

Depending on the selected file format settings, the Imager shows the captured image and a menu bar. The
menu bar shows the available options.

Note

MultiSharp Focus captures and freezes images differently. See MultiSharp Focus.

10

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Professional Series Thermal Imagers

Menus

Save Image

To save an image as a data file:

1. Capture an image.

The image is in the memory buffer for you to save or edit the image.

2. Push

 to save the image as a file and go back to the live view.

Menus

Use the menus to change and view settings.

To change settings:

1. Push

2. Push

The primary, secondary, and option menus close 10 seconds after the last push of a function button. The option
selection menu stays open until you make the selection, go up a menu level, or cancel the action.

When the Imager is in Gas Detection mode, some functions will be disabled. They will not be selectable.

Table 7 lists the secondary menus available in the Primary Menu.

X/W to select an option.

 to set the option.

Table 7. Primary Menu

Secondary Menu Description

Measurement

Image

Camera Set options for secondary camera features.

Memory Select to review and delete captured images and videos.

Fluke Connect

Settings Set user preferences and to view information about the Imager.

SF6 Gas Detection
Mode

Set the calculation and display of radiometric temperature measurement data
related to the thermal images.

Set features used to show infrared images on the display and in some saved
image and video files.

Select to pair the Imager to the Fluke Connect app on a mobile device or to other
Fluke Connect tools.

Note

The Fluke Connect system is not available in all countries.

Set options for gas-detection features.

11

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

Measurement Menu

Table 8 lists the options in the Measurement menu.

Table 8. Measurement Menu

Option Menu Option Description

Range <options>

Auto

Set Level/Span

Line Temp <options> Turns on/off the Line Temp.

Emissivity

Background <options>

Transmission <options>

Manual

Set Level/Span

Adjust Number

Select Table

Select the temperature range from one of the preset
measurement ranges or to a fully automatic range.

Sets the Level/Span to adjust automatically or manually.

With Level/Span set to Manual, changes the Level/Span. See

Level/Span.

Sets a custom emissivity value when a value from the standard
emissivity table is not appropriate for the measurement. See

Emissivity Adjustment.

Select an emissivity value from a list of common materials. See

Emissivity Adjustment.

Changes the background temperature to compensate for
reflected background temperature.

Very hot objects or very cold objects can affect the apparent
temperature and measurement accuracy of the target,
especially when surface emissivity is low. Adjust the reflected
background temperature to improve the accuracy of the
measurement.

If Display is set to Display All, the background temperature
shows as BG: xx.x on the display.

Changes the values used to calculate the temperature based
on the transmission percentage of the infrared-transparent
window (IR window), relative humidity, and the distance the
Imager is from the target. See Transmission.

If Display is set to Display All, the transmission correction
shows as T: xxx% on the display.

Note

Note

12

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Professional Series Thermal Imagers

Table 8. Measurement Menu (cont.)

Option Menu Option Description

Menus

Spot Temp

Spot Boxes

Markers

On

Off

All OFF

<options>

All OFF Turns off fixed-temperature spot markers.

<options>

Delta-T

Select to view and turn on/off either the hot or cold spot
indicator on the display.

The Spot Temperatures are floating HI and LO temperature
indicators that move on the display as the temperature
measurements of the image fluctuate.

Turns off the temperature measurement zones (boxes) that
center on a target.

Select the number of temperature measurement boxes to focus
on a target. Some models only have one Spot Box.See Spot

Boxes.

Select the number of fixed-temperature spot markers to use to
highlight a region before you take an image. See Spot Markers.

Select to set the center point or a spot marker to use as a
temperature reference mark. See Delta-T.

13

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

1

2

3

Users Manual

Level/Span

Level and Span are values within the total range of temperature set in Range. Level is the temperature level to
view within the total range of temperatures. Span is the span of temperatures to view within the total range of
temperatures. See Table 9.

Table 9. Level and Span Settings

Item Description







In automatic Level/Span mode, the Imager sets Level/Span based on the temperatures set in Range.

When the Range of the Imager is set to one of the preset measurement ranges and Level/Span is set to Manual,
the level setting moves the thermal span up or down within the total temperature range.

To change the Level/Span:

1. Select Measurement > Level/Span > Manual.

2. Select Set Level/Span.

Level

Span

Total Imager range

14

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Professional Series Thermal Imagers

Menus

3. Push:

•

•

•

•

The scale along the right side of the display shows the thermal span increasing or decreasing in size and shows
the span as it moves to different levels within the total range. See Table 9.

See Detailed Specifications for more information about the minimum span.

The Imager always powers up in the same Level/Span mode, Auto or Manual, as when the Imager was
powered down.

to decrease the temperature span.

Y

to increase the temperature span.

Z

to move the span to a higher temperature level.

W

to move the span to a lower temperature level.

X

Note

Emissivity Adjustment

All objects radiate infrared energy. The actual surface temperature and emissivity of the target affects the
quantity of energy radiated. The Imager senses the infrared energy from the surface of the target and uses the
data to calculate an estimated temperature value. Many common materials such as wood, water, skin, cloth, and
painted surfaces, including metal, radiate energy well and have a high emissivity factor of
Imager measures temperatures accurately on targets with a high emissivity.

Shiny surfaces or unpainted metals do not radiate energy well and have a low emissivity factor of <0.60. For the
Imager to calculate a more accurate estimate of the actual temperature of targets with a low emissivity, adjust the
emissivity setting.

W Warning

To prevent personal injury, see emissivity information for actual temperatures. Reflective
objects result in lower than actual temperature measurements. These objects can pose a burn
hazard.

Set emissivity as a direct value or from a list of emissivity values for some common materials. If the emissivity
value is <0.60, a caution shows on the display.

Note

<

Surfaces with an emissivity of
temperatures. The lower the emissivity is the greater the potential of error is when the Imager calculates
the temperature measurement because more of the energy reaching the camera is specified as
background temperature. This is also true even when adjustments to the emissivity and reflected
background adjustments are performed properly.

0.60 make it difficult to determine reliable and consistent actual

≥90 % (or 0.90). The

15

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

Transmission

Window %

When you do infrared inspections through IR windows, not all of the infrared energy emitted from the target is
transmitted through the optical material in the window. If you know the transmission percentage of the window,
adjust the transmission percentage in the Imager or in SmartView software to improve the accuracy of the
measurement.

When you do not do infrared inspections through an IR window, set the Window % to 100 % to disable the
correction percentage.

RH % and Distance (m)

The distance of the Imager to the target and the relative humidity can affect the temperature reading. The farther
the Imager is from the target, the greater the humidity affects the temperature reading. Set a non-zero value for
both the RH % and the Distance.

Note

If either the RH % or the Distance value is set to zero, the applied correction of both values is disabled.

Spot Boxes

Use the Spot Boxes feature to select the number of temperature measurement zones (boxes) to center on the
target and to adjust the sizes or position of the boxes. The boxes expand or contract to different levels within the
infrared image. Each box shows an approximate maximum (MAX), average (AVG), and minimum (MIN)
temperature measurement in that area.

Note

When you use Spot Boxes, the level and span of the Imager adjusts to the thermal scene within the Spot
Boxes.

To set the size and position of a Spot Box:

1. Select Measurement > Spot Boxes.

2. Select the number of Spot Boxes.

 in the new menu toggles between Size and Position.

3. If necessary, push

4. Push:

W to decrease the vertical size of the Spot Box.

•

X to increase the vertical size of the Spot Box.

•

Y to decrease the horizontal size of the Spot Box.

•

Z to increase the horizontal size of the Spot Box.

•

 to select Size.

16

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Professional Series Thermal Imagers

Menus

5. Push

6. Push

7. When you are satisfied with the size and position of the Spot Box, push

8. Repeat for each Spot Box.

9. When you are satisfied with the size and position of each Spot Box, push

 to select Position.

W / X / Y / Z to move the Spot Box location on the image.

 to set the change and select the

next Spot Box.

 to set the change and exit the

menu.

Spot Markers

Use fixed-temperature spot markers to highlight a region on the display before you save an image.

To set a marker:

1. Select Measurement > Markers.

2. Select the number of markers.

3. Push

To change the marker position on the display:

1. Push

2. When you are satisfied with the position of the marker, push

3. Repeat for each marker.

4. When you are satisfied with the position of each marker, push

 to set the number of markers and go to the Move Marker display.

 shows on the display and the labels on the function buttons change to Done, Next, and Cancel.

W / X / Y / Z to move the marker location on the image.

 to set the change and select the next

marker.

When the position of the marker is set, the marker symbol changes from

 to .

 to set the change and exit the menu.

Delta-T

Use to set the center point or a spot marker to use as a temperature reference mark.

To set a temperature reference mark:

1. Select Measurement > Markers > Delta-T.

2. Select the center point or spot marker to set as the reference mark.

 and the temperature shows on the display next to the reference mark.

A delta symbol (
next to the other spot markers.

The center point can be a temperature reference mark, but it cannot have a delta symbol. It is either the
main reference mark or it is not a delta reference at all.

) and the temperature difference relative to the temperature of the reference mark shows

Note

17

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

Image Menu

Table 10 lists the options in the Image menu.

Table 10. Image Menu

Option Menu Option Description

Select the palette to use.

Standard

Palette

IR-Fusion <options>

Ultra Contrast

Set Palette Changes the palette color.

Saturation
Colors

The Standard Palettes offer an equal, linear presentation of colors
that allow for best presentation of detail.

The Ultra Contrast Palettes offer a weighted presentation of
colors. Ultra Contrast palettes work best in situations with high
thermal contrast for extra color contrast between the high



temperatures and low temperatures.
See Detailed Specifications.

Turns on/off Saturation Colors.
If Saturation Colors is on, you can set the saturation colors to use.

Select to set the IR-Fusion mode. See Detailed Specifications for
modes available based on the model of the Imager.

The Imager automatically captures a visible image with every
infrared image to show where a potential problem might be.

The visible image and infrared image can be customized or
separated in SmartView and Fluke Connect Software when
you use the .is2 or .is3 file format. See File Format.

Note

18

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Professional Series Thermal Imagers

Table 10. Image Menu (cont.)

Option Menu Option Description

Turns on/off the high-temperature color alarm. The high-

High Alarm

Set High Alarm
Temperature

Low Alarm

Color Alarm

Set Low Alarm
Temperature

Outside

temperature color alarm shows a full visible image and only
shows infrared information on objects or areas that are above the
set apparent temperature level.

Sets the high apparent temperature level. Requires the High
Alarm to be on.

Turns on/off the low-temperature (or dew point) color alarm. The
low-temperature color alarm shows a full visible image and only
shows infrared information on objects or areas that are below the
set apparent temperature level.

Sets the low apparent temperature level. Requires the Low Alarm
to be on.

The Imager does not sense ambient or surface dew point
level automatically. To use the low-temperature color alarm
function as a dew point color alarm, determine and input the
surface dew point temperature. The colors presented can
help identify areas of concern with possible dew point
condensation.

Shows color isotherms, or infrared information, outside of a set of
both high and low limits. Requires High Alarm and Low Alarm to
be on and temperature levels for both alarms to be set.

Menus

Note

Inside

Shows color isotherms, or infrared information, inside of a set of
both high and low limits. Requires High Alarm and Low Alarm to
be on and temperature levels for both alarms to be set.

19

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

Table 10. Image Menu (cont.)

Option Menu Option Description

Sets which graphics to view on the display.

Display <options>

Image Enhancement

<options>

Features that have On/Off controls must be turned on and
turned off with those controls.

Sets the advanced image enhancement features of the Imager.
See Image Enhancement.

Note

On

Logo

Distance

Zoom <options> Sets digital zoom level.

Off

Custom

On

Off

<options> Sets units to feet or meters. See Distance.

Turns on/off the Fluke logo on the display.

With SmartView software, upload a custom logo to the Imager
from your PC through the USB connection.

Turns on/off the distance units on the display. See Distance.

Image Enhancement

Use the Image Enhancement menu to activate the advanced features of the Imager. Activate either MultiSharp
Focus or SuperResolution individually. Use Filter Mode with either MultiSharp Focus or SuperResolution.
Table 11 lists the options in the Image Enhancement menu.

Table 11. Image Enhancement Menu

Option Description

Filter Mode

Off

Combine values from successive frames within a small range of temperatures to
reduce pixel noise or thermal sensitivity (NETD) to as low as 30mK.

Turn off MultiSharp Focus mode or SuperResolution mode and not affect Filter
mode.

20

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Option Description

MultiSharp Focus

MultiSharp Focus (In PC
Only)

SuperResolution

SuperResolution (In PC
Only)

Professional Series Thermal Imagers

Menus

Table 11. Image Enhancement Menu (cont.)

MultiSharp Focus captures several images focused on multiple targets that are
positioned at different distances from the Imager and creates one image that
focuses on the multiple targets at the same time.

In MultiSharp Focus mode, you can process the image in the camera or in
SmartView software.
In MultiSharp Focus (In PC only) mode, the image is not processed on the Imager
so you cannot view the image on the Imager. Use SmartView software to view the
image on your PC. Set the file format to .is2 for MultiSharp Focus (In PC only)
mode to work.

SuperResolution uses a sensor to capture micro movements to create an image
with double the resolution. See Detailed Specifications the resolution available
based on the model of the Imager.
In SuperResolution mode, the Imager captures the data and processes the
image.

In SuperResolution (in PC only) mode, the image is not processed on the Imager
so you cannot view the image on the Imager. Use SmartView software to view the
image on your PC.

MultiSharp Focus

MultiSharp Focus captures several images focused on multiple targets that are positioned at different distances
from the Imager and creates one image that focuses on the multiple targets at the same time.

Note

The minimum focus distance with MultiSharp Focus and a standard lens is 15 cm (6 inches). For
optimum performance, position the camera
also works with all compatible lenses.

To use:

1. Point the Imager at the target.

2. Capture an image. Hold the Imager still while it captures the images.

Saving… shows on the display for ∼2 seconds for a 60 Hz model or 5 seconds for a 9 Hz model.

≥

23 cm (9 inches) from the closest target. MultiSharp Focus

21

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

3. When Saving… no longer shows on the display, you can move the Imager. If necessary, use a tripod to
stabilize the Imager while the images save.

• In MultiSharp Focus mode, the Imager collects the images in the Imager and shows the focused image on
the display in ∼8 seconds for a 60 Hz model or ∼15 seconds for a 9 Hz model.

Confirm the image on the display is what you need. If possible, process the images on the Imager.

• In MultiSharp Focus (In PC only) mode, the Imager collects the images in a single file and shows the
image on the display as it appears before you capture the image (∼2 seconds for a 60 Hz model or
∼5 seconds for a 9 Hz model).

In MultiSharp Focus (In PC only) Mode, you cannot view the focused image on the Imager. If possible,
download, process, and view the image(s) on your computer while you are at the job site. To view the
focused image, open the image with SmartView software.

Note

Some targets have abnormal thermal characteristics that can cause the MultiSharp Focus algorithm to
fail. If MultiSharp Focus mode does not capture a clear image, use LaserSharp Auto Focus or Advanced
manual focus.

SuperResolution

SuperResolution uses a sensor to capture micro movements to create an image with double the resolution. See

Detailed Specifications for the resolution available based on the model of the Imager.

To use:

1. Capture an image.

2. Hold the Imager still for ∼1 second.

• In SuperResolution mode, the Imager captures the data and processes the image. The image shows on
the display of the Imager in ∼18 seconds.

• In SuperResolution (in PC only) mode, the image is not processed on the Imager so you cannot view the
image on the Imager. Use SmartView software to view the image on your PC.

Distance

Use the Laser Pointer/Distance Finder to measure the distance, up to 30 meters, from the Imager to a target.
You can choose to show the distance on the display in feet or meters. The distance is saved as part of the image.

*W Warning

To prevent eye damage and personal injury:

• Do not look into the laser. Do not point the laser directly at persons or animals or indirectly off
reflective surfaces.

• Do not open the Product. The laser beam is dangerous to eyes. Have the Product repaired only
through an approved technical site.

22

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Professional Series Thermal Imagers

To use the distance measurement feature:

1. Turn on the distance feature and select the units to show on the display.

2. Point the Imager at the target.

3. Pull and hold the Secondary Trigger.

* shows at the top of the display.

4. Position the red laser dot on the target.

5. Release the Secondary Trigger.

The distance measurement shows on the bottom of the display. The measurement shows as “- - - -” when
the Imager cannot take a measurement. If this is the case, use a tripod or steady the Imager and retake the
measurement. If there is excessive laser movement, an error message shows on the display due to an out of
range distance.

Camera Menu

Table 12 lists the options in the Camera menu.

Table 12. Camera Menu

Option Menu Option Description

Menus

LaserSharp
Autofocus

Backlight <options> Select to set the brightness level of the display.

Torch -- Turns on/off the built in flashlight.

Video

On

Off

Video/Audio Select to record video and audio when Record Video is selected.

Video ONLY Select to record video only when Record Video is selected.

Record Video Select to start recording a video. See Video.

Turns on LaserSharp Autofocus to automatically focus on a target.
See LaserSharp Auto Focus System.

Turns off LaserSharp Autofocus to use the Advanced manual focus.
See LaserSharp Auto Focus System.

23

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

Table 12. Camera Menu (cont.)

Option Menu Option Description

Auto Capture

Wireless

Start Capture

Interval

Image Count

Manual Trigger

Temp Trigger

Set Temp Trigger

Bluetooth

WiFi Hotspot

Select to capture and save an infrared image, or series of images
based on Auto Capture settings.

Sets the number of hours, minutes, or seconds between image
captures.

Note

The minimum interval available can be affected by the file type
and visible light camera settings. Some combinations create
larger file sizes that take longer to capture and save and create a
higher minimum interval compared to others.

Sets a number of images to capture. Or, select Maximum Memory
to capture and save images until the chosen storage memory is full or
the battery runs out of power.

Select to immediately capture images when Start Capture is
selected.

Select to capture images when a value is above or below a set
temperature limit when Start Capture is selected.

With Temp Trigger selected, set the temperature and conditions to
trigger the auto capture of images.

Uses Bluetooth technology to connect the Imager to a device such as
a wireless headset. See Wireless Connectivity.

Uses the Imager to create a wireless Hotspot when no WiFi network
exists. See Wireless Connectivity.

WiFi Network

Connects the Imager to a WiFi network so you can sign into your
Fluke Connect account on the Imager. See Wireless Connectivity.

24

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Professional Series Thermal Imagers

Menus

LaserSharp Auto Focus System

The Laser Pointer/Distance Finder on the Imager is both a sighting aid and a part of the LaserSharp Auto
Focus System.

*W Warning

To prevent eye damage and personal injury, do not look into the laser. Do not point laser
directly at persons or animals or indirectly off reflective surfaces.

To use the LaserSharp Auto Focus System:

1. Select Camera > LaserSharp Auto Focus > On.

2. Point the Imager at the target.

3. Pull and hold the Secondary Trigger.

* shows at the top of the display.

4. Position the red laser dot on the target.

5. Release the Secondary Trigger.

The auto focus system automatically focuses on the object.

Note

The laser pointer is aligned parallel to the infrared lens. In AutoBlend Mode, the laser pointer dot is
positioned just above the center point marker on the display. It can be easier to use your eyes to locate
the visible laser pointer on the target not on the display.

Video

The video controls include stop, rewind, fast forward, and pause/play functions. The thermal scene and
complexity of the recorded data affects the amount of time available to record a video. The video capture format
is set in the Settings menu. For more information, see File Format.

Record Video

To record:

1. Select Camera > Video.

2. Select Video/Audio or Video ONLY.

3. Touch Record Video to set up the Imager to record a video.

G shows on the display.

4. Pull and release the Primary Trigger to start recording.

 shows on the display. The elapsed time shows at the bottom of the display.

5. Pull and release the Primary Trigger to stop recording.

6. Push

7. Push

 to end the recording session.
 to save the video file.

25

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

View Video

To play a video:

1. Open the Memory menu.

2. Select a file to play. All video files show

 on the thumbnail.

3. Push

4. Push

5. Push

 to set a file.
 to start the video. While the video plays, push Y or Z to fast forward or rewind. Push 

to return to normal speed.

 to exit the video mode.

Wireless Connectivity

The Imager has several wireless connectivity options.

Note

Before the first use of the wireless feature, enable the radio. See Enable the Radio.

Bluetooth

Use Bluetooth to connect the Imager to a device such as a wireless headset. When Bluetooth is on, L shows on
the display.

To use Bluetooth:

1. Select Camera > Wireless > Bluetooth > On.

2. Push Select to scan for available Bluetooth devices within the range of the camera.

3. Select a device.

4. Push

5. If you are prompted, enter a password.

 to connect to or disconnect from the device.

WiFi Hotspot

Use the Imager to create a wireless Hotspot when no WiFi network exists. You can use the Hotspot to download
saved pictures or stream live images from the Imager to a PC with SmartView software or to a mobile device with
the Fluke Connect app. See Stream Live to a PC and Fluke Connect Wireless System for more information.
When WiFi Hotspot is on,

WiFi is for indoor use only in Kuwait, Chile, and United Arab Emirates.

 shows on the display.

Note

To create a Hotspot, select Camera > Wireless > WiFi Hotspot > On.

To change the settings:

1. Select Camera > Wireless > WiFi Hotspot > Off.

2. Select Settings.

26

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Professional Series Thermal Imagers

3. Select an option:

• Name (SSID) to change the SSID

• Password to turn the password on/off or to change the password

• Channel to change the channel

4. Push

5. Use the keyboard to enter the information for the option.

6. Push

7. Push

 to open a keyboard on the display.

 to go back.
 to use the Imager.

WiFi Network

Use the WiFi Network setting to connect the Imager to a WiFi network and to sign into your Fluke Connect
account on the Imager. When WiFi Network is on,

To turn on the WiFi Network feature:

1. Select Camera > Wireless > WiFi Network > On.

2. Push Select to scan for available networks within range of the Imager.

3. Select a network.

4. Push

5. If you are prompted, enter a password.

 to connect to or disconnect from a network.

 shows on the display.

Menus

Sign In

When the Imager is connected to a WiFi network, you can sign into your Fluke Connect account on the Imager
and use Fluke Connect Instant Upload. When you use Fluke Connect Instant Upload, the images you take with
the Imager automatically upload to your Fluke Connect account in the Fluke Cloud. You can view the images
saved in the Fluke Cloud on the Fluke Connect app or the Fluke Connect website without the mobile device and
Imager connected to each other.

Note

The Instant Upload feature may not work on all networks or with all devices due to the security profiles
on different networks.

To sign in to your Fluke Connect account:

1. Select Camera > Wireless > Sign In to open a keyboard on the display.

2. Use the keyboard to enter your user name.

3. Push

4. Use the keyboard to enter your password.

.

27

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

5. Push

To sign out:

1. Select Camera > Wireless > Sign Out.

2. Push

.

shows on the display.

.

Fluke Connect Wireless System

The Imager supports the Fluke Connect Wireless System. The Fluke Connect system wirelessly connects your
Fluke test tools with an app on a mobile device. It shows images from the Imager on your mobile device.

Note

The Fluke Connect system is not available in all countries.

Fluke Connect App

The Fluke Connect app works with Apple and Android products. The app is available for download from the Apple
App Store and Google Play.

To use the Fluke Connect app with the Imager:

1. On the Imager, select Fluke Connect > Pair to Fluke Connect Mobile App > On.

2. On the mobile device:

a. Go to Settings > Wi-Fi.

b. Select the Wi-Fi network that begins with Fluke...

3. On the Fluke Connect app, select Thermal Imager from the list.

You can now take images on the Imager, and they will stream live from the Imager to your mobile device.
Live streaming may not be available on all devices. The pictures you take with the Imager are saved on your
mobile device and on the Imager.

Note

To save images to the Fluke Connect app, set the file format to .is2 (see File Format) and the image
storage to internal memory (see Table 13). Images stored on the SD card or USB storage device may
not transfer to the Fluke Connect app.

4. On the Imager, capture an image.

The image is now in the buffer.

5. Push

28

 to save the image and view the image on the phone app.

Go to

for more information about how to use the app.

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Professional Series Thermal Imagers

Menus

Fluke Connect Tools

Use the Imager to wirelessly connect to Fluke-Connect-supported tools to:

• View the live measurement of each tool.

• Capture the measurement of each tool in .is2 and .is3 images.

To discover a Fluke Connect-supported tool:

1. Turn on each wireless tool and make sure the wireless feature is enabled. See the documentation of each
tool for more information about how to use the tool.

2. Turn on the Imager.

3. Select Menu > Fluke Connect > Pair to Fluke Connect Tools.

4. Push

5. Select the tool name.

6. Push

7. Repeat to select each tool.

8. Select Done.

To edit the selection:

1. On the Imager, select the tool name.

2. Push

 to set selection.

The Fluke Connect button on the wireless tool starts to flash. The Imager starts to scan and presents a list
with the ID and name of available tools found within 20 m without obstructions (open air) or within 6.5 m with
obstructions (sheetrock wall). You can expect a short delay before the scan is complete.

 or touch Select to select the tool.

The labels change to include an Edit function. By default, the Imager shows and saves the data for the
selected tools.

 or touch the Edit target. The Edit menu shows the option to show the measurement data and

save it with the image to the memory location selected in the Settings menu.

The display on the Imager updates to show the wireless icon and the live measurement for each selected
wireless tool.

29

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

Memory Menu

Use the Memory menu to review or delete captured images and videos. When additional information has been
saved with the file, an icon shows with the preview file. The icons are:






IR-PhotoNotes photos

Audio

Video

Text

Review Image

To review an image:

1. Open the Memory menu.

2. Select the preview image of the file for review.

3. Push

 to review the file.

Edit Image

Before you save a file, you can use the Imager to edit or modify the image. Once the file is saved, you cannot edit
the image.

IR-PhotoNotes System

Use the IR-PhotoNotes photo annotation system to capture visible images of various objects, text, or other
information that is related to the analysis and reporting of an infrared image. A visible image is a clear digital
photo and does not use infrared technology. Examples of possible annotations include motor name plates,
printed information or warning signs, larger views of the environment or room, and related equipment or objects.
IR-PhotoNotes images are only available in the .is2 file format and are stored in the file so you do not need to
collate multiple files at a later time.

To add photos using the IR-PhotoNotes annotation system:

1. With an infrared image in the buffer, push

2. Select IR-PhotoNotes.

3. Push

4. Capture an image.

5. Capture additional images as required. See Detailed Specifications for the maximum number of images that

6. Push

 to enter the Picture mode.

can be stored with IR-PhotoNotes.

 to save the pictures with the image.

 to open the Edit Image menu.

30

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

To view an IR-PhotoNote annotation in memory:

1. Open the Memory menu.

Professional Series Thermal Imagers

Menus

2. Select a file to view. All files with IR-PhotoNotes annotations show

3. Push

 to view the photo annotations.

 with the preview file.

Audio

Audio (voice) annotation is only available in the .is2 file format. The audio is stored with the image so you do not
need to collate multiple files later.

To add, playback, or edit an audio file:

1. With an image in the buffer, push

2. Select Add Audio.

3. Do the corresponding procedure below for the desired action.

Action Procedure

1. Push

2. The display updates to show the recorded time.

3. Push

Add audio file

4. Push

5. Push

The audio file replays through the speaker.

1. Open the Memory menu.

 to open the Edit Image menu.

 to record up to 60 seconds of audio.

 to pause the recorder.
 to stop the recorder.
 to review the audio file, or push  to save the audio with the

image.

Playback audio file

Edit audio file

2. Select a file to view. All files with audio annotations show
file.

3. Push

4. Push

5. Push

1. Before you save the file, push

2.

3. Push

4. Do the steps to add an audio file.

 to listen to the file.
 again to pause the file.
 twice to exit.

 to review the audio file.

 again to pause the file.

 to append audio to the end of the file, or push  to replace the

audio file.

 with the preview

31

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

Text Notes

Text annotation is only available in the .is2 file format. Text notes are stored with the image so you do not need to
collate multiple files later.

To add a text annotation:

1. With an image in the buffer, push

2. Select Add Text.

3. Push

4. Use the keyboard to input a message.

5. Push

 to open a keyboard on the display.

 to save the message.

 to open the Edit Image menu.

6. Push

7. Push

To view a text annotation in memory:

1. Open the Memory menu.

2. Select a file to view. All files with text annotations show

3. Push

4. Push

 when done.
 to save the message with the image.

 with the preview file.

 to open the Notes menu.
 to view the text annotation.

Delete Image

To delete images, do the corresponding procedure below for the desired action.

Action Procedure

1. Open the Memory menu.

2. Select a preview image.

Delete one file

Delete all files

3. Push

4. Select Selected Image and push

5. Push

1. Open the Memory menu.

2. Push

3. Select All Images and push

4. Push

 to open the Delete menu.

.

The Imager prompts you to continue or cancel.

 again to delete the file.

 to open the Delete menu.

.

The Imager prompts you to continue or cancel.

 to delete all the files from the memory.

32

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Professional Series Thermal Imagers

Settings Menu

Table 13 lists the options in the Settings menu.

Table 13. Settings Menu

Option Menu Option Description

Menus

File Format

Units <options> Sets the temperature units to Celsius or Fahrenheit.

Auto Off

Date <options> Sets the date format and the date. See Date.

Time <options> Sets the time format and the time. See Time.

Language <options> Sets the language to use on the display.

Localization <options> Sets the decimal separator to comma or decimal point.

Image Storage <options>

Advanced

Image Format

Video Format

LCD Time Out Sets the time before the display automatically turns off.

Power Off

Filename Prefix

Reset Filename Resets the file number to 00001.

Factory Defaults

Imager Info

Adjust Parallax Fine-tunes the parallax adjustment to precisely align the image.

Sets the file type to save images and videos to and to set the
megapixels to use for the visual light camera. See File Format.

Sets the time before the Imager automatically turns off.

Note

Auto Off is automatically disabled when the battery is
connected to ac power.

Sets the location to save images: internal memory, micro SD
memory card, or USB storage device.

Changes the default filename that starts with IR_ to a different
3-character prefix with the touch screen keyboard.

Erases all user-set preferences and restores the factory default
settings.

View information about the version, certificates, and Open Source
Software Licenses of the Imager.

33

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

File Format

Select from a list of image and video file formats based on how the end file will be used. Table 14 lists the image
file formats. Table 15 lists the video file formats.

Table 14. Image File Formats

File Format Description

Saves images as a .is2 file.
Choose the .is2 file format when image modification and maximum resolution is needed.

IS2

JPEG

BMP

VLCM Resolution

The .is2 file format consolidates the infrared image, radiometric temperature data, visible
image, voice annotation, and photos from the IR-PhotoNotes photo annotation system
into a single file. To customize or separate the visible and infrared images, use
SmartView software or the Fluke Connect app.

Saves images as a .jpg file.
Choose the .jpg file format for images with the smallest file size, where modification is not
needed, and image quality and resolution are not as important.

Saves images as a .bmp file.
Choose the .bmp file format when a smaller file size with maximum resolution is needed
and image modification is not.

Sets the megapixels (MP) on the visual light camera.

Note

To use Image Enhancement features, set the VLCM Resolution to 0.3 MP.

Table 15. Video File Formats

File Format Description

Saves videos as an .is3 file with radiometric video capture.

IS3

AVI

Choose the .is3 video format when video modification and maximum resolution is needed.
To edit the .is3 video file, use SmartView software or the Fluke Connect app.

Saves videos as an .avi file with .mpeg encoding.
Choose the .avi video format when video modification is not required. The file retains the

video settings at the time the video was captured and saved.

34

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Date

The date shows as: MM/DD/YY or DD/MM/YY.

To set the date:

1. Select Settings > Date.

2. Select MM/DD/YY or DD/MM/YY.

3. Push

4. Select Set Date.

5. Push

 to set the new format.

 to open the Set Date menu.

Professional Series Thermal Imagers

Menus

6. Push

7. Push

8. Push

Y/Z

W/X

 to set the date and exit the menu.

to select Day, Month, or Year.

to change the day, month, or year.

Time

Time shows as: 24 hour or 12 hour.

To set the time format:

1. Select Settings > Time.

2. Select 24 hour or 12 hour.

3. Push

4. Select Set Time.

5. Push

6. Push

7. If you selected the 12 hour format, select AM or PM.

 to set the time format.

 to open the Set Time menu.

Y/Z

to select Hours or Minutes.

35

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

SF6 Gas Detection Mode Menu

Note

The Imager can operate in radiometric mode or in gas detection mode. The Imager cannot operate in
both modes at the same time. When SF6 Gas Detection Mode is enabled, the radiometric features of
the Imager are disabled and cannot be selected in the menus.

Table 16 lists the options in the SF6 Gas Detection Mode menu.

Table 16. SF6 Gas Detection Mode Menu

Option Description

SF6 Gas Detection Mode:
ON

SF6 Gas Detection Mode:
OFF

Image Capture

Video Capture

High Gain (Tripod)

Low Gain (Handheld)

Turns on the gas detection mode. See Gas Detection Conditions.

Turns off the gas detection mode.

Sets up the Imager to capture an image in gas mode when SF6 Gas Detection
Mode: ON is enabled.

Sets up the Imager to capture a video in gas mode when SF6 Gas Detection
Mode: ON is enabled.

Optimizes the sensitivity of the display when the Imager is mounted on a tripod
when SF6 Gas Detection Mode: ON is enabled. See Gas Detection

Conditions.

Optimizes the sensitivity of the display when the Imager is held in a hand when
SF6 Gas Detection Mode: ON is enabled. See Gas Detection Conditions.

Gas Detection Conditions

The Imager detects gas leaks based on:

• The temperature difference between the gas and the background environment

• The wind speed

• The amount of clutter in the background scene (for example, clouds)

• The stability of the Imager

• The proximity of the Imager to the leak

Note

The lower the volume of the gas leak the more challenging it is for the Imager to detect the leak.

36

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Professional Series Thermal Imagers

To improve the gas detection rate, place the Imager where:

• The temperature difference between the gas and the background environment is the greatest.

• There is a light wind.

• There is limited clutter in the background scene. A clear blue sky is optimal.

• The Imager is stable. When possible, use a tripod and High Gain (Tripod) mode.

• The Imager is close to the leak. If close proximity is not possible, use the 2X lens.

Table 17 lists the guidelines for the Imager to detect a gas leak based on the annual gas loss rate.

Table 17. Detection Guidelines

Menus

Annual Gas

Loss Rate

<10 lbs (<4.5 kg)

10 lbs to 50 lbs (4.5 kg
to 22,7 kg)

>50 lbs (>22,7 kg)

Guidelines

• The greatest possible difference between the gas and the background
environment temperatures

• Wind speed: <1.12 mps (<2.5 mph)

• Uniform background scene (clear blue sky)

• Imager on a tripod, close to the gas leak.

• ≥10 °C difference between the gas and the background environment temperatures

• Wind speed: <2.24 mps (<5 mph)

• Variable background scene (clear blue sky, high altitude clouds okay)

• Imager on a tripod.

• ≥3 °C difference between the gas and the background environment temperatures

• Wind speed: <4.47 mps (<10 mph)

• Variable background scene (high altitude clouds okay)

• Imager on a tripod or handheld.

37

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

SmartView Software

SmartView software for a PC is available to use with the Imager and contains features to analyze images,
organize data and information, and make professional reports.

Use SmartView software to:

• Review IR-PhotoNotes, audio, and text annotations.

• Export IR and visible images.

• Edit .is2 image files and .is3 video files.

• Enable Bluetooth, WiFi, and Fluke Connect functions.

• Update the firmware for new Imager feature

Download SmartView Software

Go to .

1. On the website, follow the instructions to download the software to the PC.

2. On the PC, follow the instructions to install SmartView software. (Administrator privileges are required for the
installation.)

3. Restart the PC when installation is complete.

Download Firmware

1. On the PC, open SmartView software.

2. Connect the USB A connector end of the cable into your PC and the USB Micro B connector end into the
Imager.

Note

Some Imagers have both A and Micro B connector jacks. Make sure to use the Micro B jack on the
Imager.

Windows automatically installs the device driver for use with the Imager. SmartView software recognizes the

connection with the Imager and appears on the SmartView software toolbar menu.

3. On the PC, select Yes if prompted to download a firmware update file onto the PC.

4. On the Imager, once the firmware is downloaded, select Update Firmware, to update the firmware in the
Imager.

To complete the firmware update, the Imager turns off.

5. To use the new firmware, turn on the Imager.

38

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Professional Series Thermal Imagers

Streaming Video (Remote Display)

Enable the Radio

In countries with laws and regulations that permit wireless communications, wireless communication protocols
are available to expand the capabilities of the Imager. All Imagers ship from the factory with the radios disabled.

To enable the radio:

1. On the Imager, select Camera > Fluke Connect.

2. On the PC, go to

3. On the website:

a. Select a language from the drop down box.

b. Enter your information and the serial number from the display on the Imager. The serial number is case

sensitive.

c. Click on Submit.

If the radio is authorized in your country, an authorization code appears on the web page.

If the radio is not yet authorized in your country, Fluke will contact you when the radio is authorized for
use in your country.

4. On the Imager,

a. Push

b. Type in the authorization code from the website. (The authorization code is not case sensitive.)

c. Push

d. Tap Ok.

5. Connect to a wireless device, if desired. See Wireless Connectivity.

 or tap Enter Code.

 or Done.

A message appears on the Imager display that shows the wireless communication is enabled.

If a message appears that says the authorization code is invalid:

• Make sure you entered the correct serial number from the Imager into the website.

• Make sure you entered the correct authorization code from the website into the Imager.

.

Note

Streaming Video (Remote Display)

The Imager can stream live infrared and IR-Fusion technology video to a PC that has SmartView software
installed, to the Fluke Connect app (where available), or to an HDMI compatible device.

39

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

Stream Live to a PC

To stream live to a PC through a USB connection:

1. Install the latest version of the firmware on the Imager. See Download Firmware.

2. On the PC, open the SmartView software.

3. Connect the USB A connector end of the cable into your PC and the USB Micro B connector end into the
Imager.

Note

Some Imagers have both A and Micro B connector jacks. Make sure to use the Micro B jack on the
Imager

appears on the SmartView software toolbar menu.

4. On the PC, choose Remote Display from .

To stream live to a PC, wirelessly:

1. On the Imager, turn on the WiFi Hotspot. See WiFi Hotspot.

2. On the PC:

a. From the networks screen, select Fluke-Camera.

Note

Fluke-Camera is the default name of the Imager. If you changed the name of the Imager, select the new
name of the Imager from the networks on the PC.

b. Open the SmartView software.

appears on the SmartView software toolbar menu.

c. Choose Remote Display from .

Stream Live with Fluke Connect Software

To stream live with Fluke Connect software, see Fluke Connect Wireless System.

Stream Live to an HDMI Device

HDMI (High-Definition Multimedia Interface) is a compact audio/video interface that transfers uncompressed data
and compressed/uncompressed digital audio data from the Imager to a compatible HDMI device.

To stream live to an HDMI device:

1. Attach the included HDMI cable to the HDMI port on the Imager.

2. Connect the other end to an HDMI video device.

40

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Professional Series Thermal Imagers

Remote Control of Imager

Remote Control of Imager

Use SmartView software on a PC or the Fluke Connect app on a mobile device to remotely control the Imager.

To remotely control the Imager with a PC:

1. Turn on Remote Display. See Stream Live to a PC.

2. In SmartView software, select SmartView (Camera is the default selection).

When in remote control mode, use the SmartView software to control all the menus on the Imager. The menus
cannot be changed directly on the Imager.

To remotely control the Imager with the Fluke Connect app:

1. Set up the Fluke Connect system. See Fluke Connect Wireless System.

2. On the mobile device, tap on the streaming image.

An option shows to Remote Control the Imager.

3. Select Yes.

From the mobile device, you can change the IR-Fusion setting, select Auto Focus to turn on LaserSharp Auto
Focus, or tap the green Capture button to take an image. You can change the other menu items on the Imager
directly even while the mobile device remotely controls the Imager.

Accessories

Table 18 is a list of the accessories available for the Imager.

Table 18. Accessories

Model Description PN

FLK-TI-SBP3 Smart Battery Pack 3440365

FLK-TI-SBC3B Charging Base/Power Supply with Adapters 4354922

TI-CAR CHARGER 12 V Vehicle Charger Adapter 3039779

FLUKE-TI-VISOR3 Sun Visor 4335377

FLUKE-TI-TRIPOD3 Tripod Mounting Accessory 4335389

FLK-Bluetooth Bluetooth Headset 4603258

BOOK-ITP Introduction to Thermography Principles 3413459

FLK-LENS/TELE2 2X Telephoto Infrared Lens 4335377

FLK-LENS/WIDE2 Wide-Angle Infrared Lens 4335361

FLK-LENS/4XTELE2 4X Telephoto Infrared Lens 4607058

FLK-LENS/25MAC2 25-Micron Macro Infrared Lens 4607064

41

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

Optional Lenses

Use optional telephoto and wide-angle lenses for more applications of infrared inspection work. To install a lens,
align the dot on the lens with the dot on the Product. See Figure 1.

1

2

3

1

Figure 1. Optional Lens Installation

42

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Professional Series Thermal Imagers

Maintenance

Maintenance

The Imager does not require maintenance.

*W Warning

To prevent eye damage and personal injury, do not open the Product. The laser beam is
dangerous to eyes. Have the Product repaired only through an approved technical site.

Clean the Case

Clean the case with a damp cloth and a weak soap solution. Do not use abrasives, isopropyl alcohol, or solvents
to clean the case.

Lens Care

W Caution

To prevent damage to the infrared lens:

• Carefully clean the infrared lens. The lens has a delicate anti-reflective coating.

• Do not clean the lens too vigorously because this can damage the anti-reflective coating.

To clean the lens:

1. Use a pressurized can of air or a dry nitrogen-ion gun, if available, to blow off the particulates from the lens

surface.

2. Soak a lint-free cloth in a commercial lens cleaning liquid that contains alcohol, ethyl alcohol, or isopropyl

alcohol.

3. Squeeze the cloth to remove excess liquid.

4. Wipe the lens surface in one circular motion and discard the cloth.

5. If needed, repeat with a new lint-free cloth.

Battery Care

W Warning

To prevent personal injury and for safe operation of the Product:

• Do not put battery cells and battery packs near heat or fire. Do not put in sunlight.

• Do not disassemble or crush battery cells and battery packs.

• Remove batteries to prevent battery leakage and damage to the Product if it is not used for an
extended period.

• Connect the battery charger to the mains power outlet before the charger.

• Use only Fluke approved power adapters to charge the battery.

• Keep cells and battery packs clean and dry. Clean dirty connectors with a dry, clean cloth.

43

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

W Caution

To prevent damage, do not expose Product to heat sources or high-temperature environments
such as an unattended vehicle in the sun.

To get the best performance from the lithium-ion battery:

• Do not store the Imager on the charger for more than 24 hours as reduced battery life may result.

• Charge the Imager for a two-hour minimum at six-month intervals for maximum battery life. Without use, the
battery will self-discharge in approximately six months. Batteries stored for long periods will need two to ten
charging cycles for full capacity.

Charge Batteries

Before you use the Imager for the first time, charge the battery for a minimum of two and one-half hours. The
battery status shows on the five-segment charge indicator.

Note

New batteries are not fully charged. Two to ten charge/discharge cycles are necessary before the
battery charges to its maximum capacity.

To charge the battery, use one of the options that follow.

Two-Bay Battery Charger Base

1. Connect the ac power supply to the ac wall outlet and connect the dc output to the charger base.

2. Put one or two smart batteries into bays of charger base.

3. Charge batteries until charge LEDs on charger base are a solid green.

4. Remove smart batteries and disconnect the power supply when batteries are fully charged.

AC Power Socket on Imager

1. Connect the ac power adapter into an ac wall outlet and connect the dc output to the Imager’s ac power
socket.

2. Charge until the charge indicator on the display does not flash.

3. Disconnect the ac power adapter when the smart battery is fully charged.

Make sure that the Imager is near room temperature before you connect it to the charger. See the
charging temperature specification. Do not charge in hot or cold areas. When you charge in extreme
temperatures, battery capacity may be decreased.

 shows on the display when the Imager is connected to ac power and the battery is removed. When the
power is off on the Imager and the ac power adapter is connected to the Imager,
show that the battery charge is in process.

 flashes on the display while the battery charges with the ac power adapter.

Note

 flashes on the display to

44

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Professional Series Thermal Imagers

Radio Frequency Data

Keep the Imager attached to the charger until the battery condition icon shows a full charge. If you remove the
Imager from the charger before a full charge shows, it can have a reduced run-time.

Note

When the battery is connected to ac power or the unit is in video mode, the Sleep Mode/Auto Off feature
is disabled automatically.

Optional 12 V Vehicle Charger

1. Connect the 12 V adapter into the 12 V accessory socket of the vehicle.

2. Connect the output to the ac power socket of the Imager.

3. Charge until the indicator shows full on the screen.

4. Disconnect the 12 V adapter and Imager when battery is fully charged.

W Caution

To prevent damage to the Imager, remove it from the dc car charger before you start or jump
start the vehicle.

• Always operate in the specified temperature range.

• Do not store the batteries in extreme cold environments.

• Do not attempt to charge the batteries in extreme cold environments.

~ W Caution

Do not incinerate the Product and/or battery.

Radio Frequency Data

See Table 13 for instructions on how to access digital copies of the Certificate IDs on the Imager.

General Specifications

Ti300 PRO Ti400 PRO Ti401 PRO Ti450 PRO Ti450 SF6 Ti480 PRO

Temperature

Operating -10 °C to 50 °C (14 °F to 122 °F)

Storage -20 °C to 50 °C (-4 °F to 122 °F) without batteries

Relative Humidity 10 % to 95 % non-condensing

Altitude

Operating 2000 m

Storage 12 000 m

Display 8.9 cm (3.5 in) touchscreen diagonal landscape color VGA LCD with backlight

45

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

Ti300 PRO Ti400 PRO Ti401 PRO Ti450 PRO Ti450 SF6 Ti480 PRO

Power

Batteries 2 Lithium-ion rechargeable smart battery packs with 5-segment LED to show charge level.

2 hours to
3hours

3 hours to 4 hours continuous

Battery Life

Battery Charge Time 2.5 hours to full charge

Battery Charge Temperature 0 °C to 40 °C (32 °F to 104 °F)

AC Battery Charge

AC Operation

Power Save User-selectable Sleep and Power Off modes

Safety IEC 61010-1: Pollution Degree 2

Wireless Radio

Frequency 2412 MHz to 2462 MHz

Output Power <100 mW

Laser IEC 60825-1:2014, Class 2

Wavelength 650 nm

Max Output Power <1mW

Electromagnetic Compatibility (EMC)

International EN61326-1, CISPR 11: Group 1, Class A

Group 1: Equipment has intentionally generated and/or uses conductively-coupled radio frequency energy that is necessary for the
internal function of the equipment itself.

Class A: Equipment is suitable for use in all establishments other than domestic and those directly connected to a low-voltage
power supply network that supplies buildings used for domestic purposes. There may be potential difficulties in ensuring
electromagnetic compatibility in other environments due to conducted and radiated disturbances.

Caution: This equipment is not intended for use in residential environments and may not provide adequate protection to radio
reception in such environments.

Korea (KCC) Class A Equipment (Industrial Broadcasting & Communication Equipment)

Class A: Equipment meets requirements for industrial electromagnetic wave equipment and the seller or user should take notice of
it. This equipment is intended for use in business environments and not to be used in homes.

USA (FCC) 47 CFR 15 Subpart C Sections 15.207, 15.209, 15.249

Random Vibration

Sinusoidal Vibration

Half-sine Shock 25 G, IEC 68-2-29

Drop 2 m (with standard lens)

Size (H x W x L) 27.7 cm x 12.2 cm x 16.7 cm (10.9 in x 4.8 in x 6.5 in)

Weight (includes battery) 1.04 kg (2.3 lb)

Ingress Protection Rating IEC 60529: IP54

Calibration Cycle 2 years (assumes normal operation and normal aging)

Supported Languages

use for each battery pack
(Actual life depends on settings
and usage.)

Ti SBC3B Two Bay Battery Charger (110 V ac to 220 V ac, 50/60 Hz, included), or in-Imager
charging. AC univeral adapters included. Optional 12 V automotive charging adapter.

AC operation with included power supply: 110 V ac to 220 V ac, 50/60 Hz ac universal adapters
included

2

/Hz (3.8 g

0.03 g

10 Hz to 70.5 Hz (0.3 mm amplitude), 70.5 Hz to 150 Hz (3 g

Czech, Dutch, English, Finnish, French, German, Hungarian, Italian, Japanese, Korean, Polish,
Portuguese, Russian, Simplified Chinese, Spanish, Swedish, Traditional Chinese, and Turkish

, 5 Hz to 500 Hz, 3 axis, 30 min/axis), 2.5 g, IEC 60068-2-6

RMS

continuous use
for each
battery pack
(Actual life
depends on
settings and
usage.)

3 hours to 4 hours continuous
use for each battery pack
(Actual life depends on settings
and usage.)

)

PEAK

2 hours to
3hours
continuous use
for each
battery pack
(Actual life
depends on
settings and
usage.)

46

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Professional Series Thermal Imagers

Detailed Specifications

Detailed Specifications

Ti300 PRO Ti400 PRO Ti401 PRO Ti450 PRO Ti450 SF6 Ti480 PRO

Temperature Measurements

Temperature Range (not calibrated
below -10 °C)

Accuracy

Imagining Performance

Image Capture Frequency 9 Hz or 60 Hz refresh rate depending on model variation

Detector Resolution 240 x 180 320 x 240 640 x 480 320 x 240 320 x 240 640 x 480

Total pixels 43 200 76 800 307 200 76 800 76 800 307 200

SuperResolution NA NA NA

Thermal Sensitivity (NETD)

Infrared spectral band 7.5 μm to 14 μm (long wave)

Digital Zoom NA NA NA 2X, 4X 2X, 4X 2X, 4X

IR-Fusion Technology

Autoblend mode 100 %, 75 %, 50 %, 25 % IR plus full visible on camera

Picture-in-Picture 100 %, 75 %, 50 %, 25 % IR

Visual (Visible Light) Camera

Type Industrial performance 5.0 MP

Parallax alignment with standard IR
lens

Standard Infrared Lens

Field of View (H x V) 24 ° x 17 ° 24 ° x 17 ° 34 ° x 24 ° 24 ° x 17 ° 24 ° x 17 ° 34 ° x 24 °

Spatial Resolution (IFOV) 1.75 mRad 1.31 mRad 0.93 mRad 1.31 mRad 1.31 mRad 0.93 mRad

Minimum Focus Distance 15 cm (∼6in)

IR-Fusion Autoblend Picture-in-Picture and Full screen

Optional 2X telephoto smart lens

Field of View (H x V) 12 ° x 9 ° 12 ° x 9 ° 17 ° x 12 ° 12 ° x 9 ° 12 ° x 9 ° 17 ° x 12 °

Spatial Re

Minimum Focus Distance 45 cm (∼18 in)

IR-Fusion blending Picture-in-Picture and Full screen

Optional 4X telephoto smart lens

Field of View (H x V) 6.0 ° x 4.5 °

Spatial Resolution (IFOV) 0.44 mRad 0.33 mRad 0.23 mRad 0.33 mRad 0.33 mRad 0.23 mRad

Minimum Focus Distance 1.5 m (∼5 ft)

IR-Fusion blending

Optional wide-angle smart lens

Field of View (H x V) 48 ° x 34 °

Spatial Resolution (IFOV) 3.49 mRad 2.62 mRad 1.31 mRad 2.62 mRad 2.62 mRad 1.31 mRad

Minimum Focus Distance 15 cm (∼6in)

IR-Fusion blending Full screen

solution (IF

OV) 0.87 mRad 0.65 mRad 0.47 mRad 0.65 mRad 0.65 mRad 0.47 mRad

-20 °C to
650 °C

±2 °C or 2 % (whichever is greater) at 25 °C ambient

≤0.04 °C at

30 °C
target temp
(40 mK)

From ∼60 cm (∼24 in) to infinity

Picture-in-Picture and Full
screen

-20 °C to
1200 °C

≤0.04 °C at
30 °C
target temp
(40 mK)

-20 °C to
650 °C

≤0.075 °C at
30 °C
target temp
(75 mK)

NA

-10 °C to
1500 °C

640 x 480 (307 200 pixels)

≤0.025 °C at
30 °C
target temp
(25 mK)

Picture-in-Picture and Full
screen

-10 °C to
1500 °C

[1]

≤0.025 °C at
30 °C
target temp
(25 mK)

[1]

-20 °C to
1000 °C

1280 x 960

≤0.050 °C at
30 °C
target temp
(50 mK)

NA

47

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Ti300 PRO, Ti400 PRO, Ti401 PRO Ti450 PRO, Ti450 SF6, Ti480 PRO

Users Manual

Ti300 PRO Ti400 PRO Ti401 PRO Ti450 PRO Ti450 SF6 Ti480 PRO

Optional macro smart lens

Minimum Spot Size 25 μ

Field of View (H x V) 36.1 ° x 27.1 °

Working Distance ∼8 mm (0.3 in) to ∼14 mm (0.6 in) with optimal at 10 mm (0.4 in)

Image Presentation

Palettes

Standard

Ultra Contrast Radiometric Mode

Gas Mode NA NA NA NA

Level and Span

Smooth Auto-Scaling and Manual scaling of level and span

Fast auto toggle between manual and auto modes

Fast auto-rescale in manual mode

Minimum Span (in manual mode)

Minimum Span (in auto mode)

Image Capture and Data Storage

Storage Medium

Internal Flash Memory 4 GB

Micro SD Memory Card

USB Storage Device

Fluke Cloud Permanent Storage Yes

File Formats

Export File Formats with SmartView
Software

Memory Review Thumbnail and full screen review

Grayscale, Grayscale Inverted, Rainbow, Blue-Red, High Contrast, Hot Metal, Ironbow, Amber,
Amber Inverted

2.0 °C (3.6 °F)

3.0 °C (5.4 °F)

Includes ≥4 GB memory card to store at least 2000 fully radiometric (.is2) IR and linked IR­PhotoNotes images each with 60 sec voice annotations or 5000 basic (.bmp, .jpg) files.

USB port available (USB storage device not included)

Non-Radiometric (.bmp, .jpg) or Fully-Radiometric (.is2). No analysis software is required for Non­Radiometric (.bmp, .jpg) files.

.bmp, .gif, .jpg, .png, .tiff

[1]

[1]

Note

Fluke recommends the memory card that is supplied with the Imager or available
from Fluke. Fluke does not warrant the use or reliability of aftermarket memory cards
of different brands or capacities.

Note

The addition of IR-PhotoNotes or other saved items can vary the total number of
images that can be stored in internal memory or on the SD memory card.

Grayscale,
Grayscale
Inverted, Hot
Metal,
Ironbow,
Amber, Amber
Inverted

NA

48

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Professional Series Thermal Imagers

Detailed Specifications

Ti300 PRO Ti400 PRO Ti401 PRO Ti450 PRO Ti450 SF6 Ti480 PRO

Video Recording

Viewable through Smart View
software, Windows Media

Standard, Non-Radiometric

Recording Speed

Radiometric

Recording Speed

IR-PhotoNotes Annotation 5 images 5 images 2 images 5 images 5 images 5 images

Audio (Voice) Annotation

Text Annotation Yes

Streaming Video (Remote Display)

SmartView Software on PC USB, WiFi Hotspot, or WiFi Network

Mobile Device Fluke Connect app with WiFi Hotspot

TV Monitor HDMI

Remote Control Operation

Wireless Connectivity PC, mobile device (iOS 4s or newer or Android 4.3 or newer), and WiFi to LAN (where available)

Gas Leak Detection NA NA NA NA

[1] Applies to radiometric mode only.
[2] When SF6 Gas Detection mode is enabled, the radiometric features of the Imager are disabled and cannot be selected in the menus.

Player, Quicktime, and on
Imager. H.264 MPEG encoding
AVI will also allow voice
recording in addition to
captured video.

24 fps (9 fps for imagers with
9 Hz refresh rate.)

Viewable on Imager and with
SmartView software in
proprietary .is3 format.
Supports voice recording in
addition to captured video.

20 fps (9 fps for imagers with
9 Hz refresh rate.)

Up to 60 sec recording time per image. Reviewable playback on camera. Optional Bluetooth
headset available, but not required.

SmartView software or Fluke
Connect app

NA

NA 24 fps (9 fps for imagers with 9 Hz refresh rate.)

NA

NA 20 fps (9 fps for imagers with 9 Hz refresh rate.)

NA SmartView software or Fluke Connect app

Viewable through Smart View software,
Windows Media Player, Quicktime, and on
Imager. H.264 MPEG encoding AVI will also
allow voice recording in addition to captured
video.

Viewable on Imager and with SmartView
software in proprietary .is3 format. Supports
voice recording in addition to captured video.

Yes

[2]

NA

49

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com