DSX-CHA003S
Coaxial Cable Adapters
Users Guide
The DSX-CHA003 coaxial adapters let you use the DSX CableAnalyzer™ to certify
coaxial cabling for network and video applications.
The coaxial cabling kit has these items:
Two DSX-CHA003 adapters
Two female to female F-connector adapters
Two F-connector female to BNC female adapters
One 12 inch (30 cm) 75 coaxial patch cord with male F-connectors
Safety Information
Warning
To prevent possible fire, electric shock, or personal injury, read the
safety information in the documentation supplied with the modules
and the Versiv
To prevent damage to the tester, adapters, and cables under test, to
prevent data loss, and to make sure your test results are as accurate
as possible, set the reference for coaxial cable before you use the
coaxial adapters for the first time, and approximately every thirty
days after that.
™
units before you use the tester.
Caution
PN 4579835 November 2014, Rev. 1 8/2015
2014-2015 Fluke Corporation
All product names are trademarks of their respective companies.
Set the Reference for Coaxial Tests
Coaxial adapter
with F-connector
adapter
12 inch (30 cm) 75
coaxial patch cord
Coaxial adapter
with F-connector
adapter
The reference procedure for coaxial tests sets the baseline for insertion loss and
resistance measurements. Set the reference at these times:
When you want to use the tester with a different module. The tester can save
reference values for eight different pairs of modules.
Every 30 days, at minimum. To ensure maximum accuracy of test results, set the
reference daily.
It is not necessary to set the reference again if you use different coaxial adapters.
To set the reference
1
Make the connections shown in Figure 1.
2
Turn on the tester and the remote a minimum of 1 minute before you set
the reference.
Notes
Set the reference only after the testers are at an ambient
temperature between 10 °C and 40 °C (50 °F and 104 °F).
The tester will not let you set the reference if the patch cord is longer
than 30 cm (12 in).
You can also set the reference with a 50 patch cord
3
On the home screen, select a copper cable test.
4
On the home screen, tap TOOLS, then tap Set Reference.
5
On the SET REFERENCE screen tap TEST.
2
DSX-CHA003
COAX ADAPTER
DSX-CHA003
COAX ADAPTER
Figure 1. Connections for the Reference Procedure
GPU179.EPS
Do Tests on Coaxial Cabling
Figure 2 shows typical connections for tests on coaxial cabling. Be sure to select the
test limit applicable to the link.
The Autotest includes these tests:
Length
Resistance (remote or terminator required)
Impedance
Insertion Loss (remote required)
Propagation delay
HDTDR analyzer
Note
The minimum cable length for an impedance measurement is
13 ft (4 m). For impedance measurements on shorter cables,
the tester shows Cable too short, and an for the impedance
and overall test results.
If No Remote is Connected
If the remote tester is not connected or the cable is too long, the main tester’s toner
turns on and the MEASURE button shows. If you tap MEASURE, the tester does the
length, impedance, and resistance tests, which do not require a remote. If a
terminator is connected, the tester gives a resistance measurement, but shows End
not found for the length measurement.
For More Information
For more information on coaxial tests and results, see the documentation supplied
with your tester and available on the Fluke Networks website.
3
DSX-CHA003
COAX ADAPTER
DSX-CHA003
COAX ADAPTER
DSX-CHA003
COAX ADAPTER
DSX-CHA003
COAX ADAPTER
DSX-CHA003
COAX ADAPTER
DSX-CHA003
COAX ADAPTER
DSX-CHA003
COAX ADAPTER
Disconnect all drop cables
MoCA
adapter
MoCA
adapter
Router
IP cameras
Surveillance network
Cable TV
Cable spools
Coaxial segment
Note: Do not connect the
testers to splitters.
Data network
Figure 2. Examples of Connections for Tests on Coaxial Cabling
V01.EPS
4
Maintenance and Service
Clean the adapters with a soft cloth that is moist with water or water and a mild
soap. Do not use abrasives, solvents, or alcohol.
If an adapter does not operate correctly, look for damage to the adapter’s
connectors. Make sure that the adapter is latched tightly to the tester.
For service on the adapters, speak to a Fluke Networks representative for
information on service centers.
For the most current test limits and features, keep your tester’s software up to date.
The latest version of software is available on the Fluke Networks website.
Specifications
The coaxial adapters comply with all measurement accuracy specifications for Level
IV test equipment. For more information, see the documentation supplied with
your tester and available on the Fluke Networks website.
Dimensions (each adapter): 3.0 in x 2.1 in x 1.2 in (75 mm x 54 mm x 30 mm)
Weight (each adapter): 2.8 oz (79 g)
Do not put products containing circuit boards into the garbage. Dispose
of circuits boards in accordance with local regulations.
Contact Fluke Networks
www.flukenetworks.com
support@flukenetworks.com
1-800-283-5853, +1-425-446-5500
Fluke Networks operates in more than 50 countries worldwide. For more contact
information, visit our website.
5
LIMITED WARRANTY AND LIMITATION OF LIABILITY
Fluke Networks mainframe products will be free from defects in material and
workmanship for one year from the date of purchase, unless stated otherwise herein.
Parts, accessories, product repairs and services are warranted for 90 days, unless
otherwise stated. Ni-Cad, Ni-MH and Li-Ion batteries, cables or other peripherals are
all considered parts or accessories. This warranty does not cover damage from
accident, neglect, misuse, alteration, contamination, or abnormal conditions of
operation or handling. Resellers are not authorized to extend any other warranty
on Fluke Networks’ behalf. To obtain service during the warranty period, contact
your nearest Fluke Networks authorized service center to obtain return
authorization information, then send your defective product to that Service Center
with a description of the problem.
For a list of authorized resellers, visit www.flukenetworks.com/wheretobuy.
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS
FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE
NETWORKS IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR THEORY.
Since some states or countries do not allow the exclusion or limitation of an implied
warranty or of incidental or consequential damages, this limitation of liability may
not apply to you.
4/15
Fluke Networks
PO Box 777
Everett, WA 98206-0777
USA
6
Loading...