Fluke CertiFiber Pro, CFP-100-M, CFP-100-S, CFP-Q-ADD, CFP-100-Q User Manual

Download

Page 1

CertiFiber® Pro

Optical Loss Test Set

Users Manual

May 2013 (English)

Page 2

LIMITED WARRANTY AND LIMITATION OF LIABILITY

Each Fluke Networks product is warranted to be free from defects in material and workmanship under normal use and service. The warranty period for the mainframe is one year and begins on the date of purchase. Parts, accessories, product repairs and services are warranted for 90 days, unless otherwise stated. Ni-Cad, Ni-MH and Li-Ion batteries, cables or other peripherals are all considered parts or accessories. The warranty extends only to the original buyer or end user customer of a Fluke Networks authorized reseller, and does not apply to any product which, in Fluke Networks’ opinion, has been misused, abused, altered, neglected, contaminated, or damaged by accident or abnormal conditions of operation or handling. Fluke Networks warrants that software will operate substantially in accordance with its functional specifications for 90 days and that it has been properly recorded on non-defective media. Fluke Networks does not warrant that software will be error free or operate without interruption.

Fluke Networks authorized resellers shall extend this warranty on new and unused products to end-user customers only but have no authority to extend a greater or different warranty on behalf of Fluke Networks. Warranty support is available only if product is purchased through a Fluke Networks authorized sales outlet or Buyer has paid the applicable international price. Fluke Networks reserves the right to invoice Buyer for importation costs of repair/replacement parts when product purchased in one country is submitted for repair in another country.

Fluke Networks warranty obligation is limited, at Fluke Networks option, to refund of the purchase price, free of charge repair, or replacement of a defective product which is returned to a Fluke Networks authorized service center within the warranty period.

To obtain warranty service, contact your nearest Fluke Networks authorized service center to obtain return authorization information, then send the product to that service center, with a description of the difficulty, postage and insurance prepaid (FOB destination). Fluke Networks assumes no risk for damage in transit. Following warranty repair, the product will be returned to Buyer, transportation prepaid (FOB destination). If Fluke Networks determines that failure was caused by neglect, misuse, contamination, alteration, accident or abnormal condition of operation or handling, or normal wear and tear of mechanical components, Fluke Networks will provide an estimate of repair costs and obtain authorization before commencing the work. Following repair, the product will be returned to the Buyer transportation prepaid and the Buyer will be billed for the repair and return transportation charges (FOB Shipping point).

THIS WARRANTY IS BUYER’S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. FLUKE NETWORKS SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, INCLUDING LOSS OF DATA, ARISING FROM ANY CAUSE OR THEORY.

Since some countries or states do not allow limitation of the term of an implied warranty, or exclusion or limitation of incidental or consequential damages, the limitations and provision of this Warranty is held invalid or unenforceable by a court or other decisionmaker of competent jurisdiction, such holding will not affect the validity or enforceability of any other provision.

ions of this warranty may not apply to every buyer. If any

exclus

4/04

Fluke Networks PO Box 777 Everett, WA 98206-0777 USA

Page 3

Chapter 1 Get Acquainted

Overview of the CertiFiber Pro Optical Loss 

Test Set Modules .............................................................1

ct Fluke Networks .................................................2

Conta

Technical Reference Handbook .....................................3

Additional Resources ......................................................3

Supplements and Updated Manuals .............................3

Kit Contents ....................................................................

-100-M Kit ...........................................................4

CFP

CFP-100-S Kit .............................................................4

CFP-100-Q Kit ............................................................5

CFP-Q-ADD Kit ..........................................................6

Safety Information ...................................................7

Connectors, Keys, and LEDs ............................................10

The Home Screen for CertiFiber Pro Modules ...............15

AC Adapter and Battery ................................................18

Charge the Battery ...................................................18

Check the Battery Status ..........................................18

How to Use the Touchscreen .........................................21

Verify Operation .............................................................23

Change the Language ....................................................23

Buttons to Do Tests and Save Results ............................

Overview of Memory Functions .....................................25

Options for Cable IDs ......................................................26

Page 4

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

How to Remove and Install the Connector Adapters .. 27

How to Install a Strap .................................................... 29

How to Remove or Install a Module ............................. 29

About LinkWare and LinkWare Stats Software ........... 31

Chapter 2 How to Clean Fiber Endfaces

How to Use a Fluke Networks IBC OneClick Cleaner ... 36

How to Use Wipes, Swabs, and Solvent ........................ 38

To Clean Bulkhead Connectors ...............................

o Clean the Optical Connectors on the Modules . 39

To Clean Fiber Adapters .......................................... 39

To Clean Connector Ends ........................................ 39

Chapter 3 How to Certify Fiber Cabling

Requirements for Reliable Fiber Test Results ............... 41

About the Reference for Fiber Tests ....................... 42

When to Set the Reference .............................. 42

Good Reference Values ..................................... 43

How to See the Reference Values ....................44

About Test Reference Cords and Mandrels ............ 44

About the EF-TRC (Encircled-Flux 

Test Reference Cords) ....................................... 44

About APC Connectors ......................................

About

Settings for Fiber Tests ...................................................

About

Autote

1 Jumper Reference Connections ...................... 55

st in Smart Remote Mode .................................. 55

Step 1: Set the Reference in Smart 

Remote Mode .......................................................... 57

Standard Mandrels ................................ 47

Page 5

Contents

Step 2: Measure the Loss of the Test 

Reference Cords You Will Add ................................59

Step 3: Do an Autotest in Smart Remote Mode .....60

Autotest Results for Smart Remote Mode ..............61

Fiber IDs for Saved Results in Smart 

Remote Mode ...........................................................61

Autotest in Loopback Mode ..........................................

Step 1: Set the Reference in Loopback Mode .........66

Step 2: Measure the Loss of the Test 

Reference Cord You Will Add ..................................68

Step 3: Do an Autotest in Loopback Mode .............69

Autotest Results for Loopback Mode ......................70

Autotest in Far End Source Mode ..................................72

Auto Wavelength Modes .........................................72

Step 1: Set the Reference in Far End 

Source Mode .............................................................74

Step 2: Measure the Loss of the Test 

Reference Cord You Will Add ..................................77

Step 3: Do an Autotest in Far End Source Mode ....77

Autotest Results for Far End S

Bi-Directional Tests .........................................................80

urce Mode .............78

Chapter 4 The FiberInspector Test

How to Do the FiberInspector Test ................................83

Chapter 5 The Visual Fault Locator

Visual Fault Locator Applications ..................................89

How to Use the VFL ........................................................90

Chapter 6 The Power Meter and Light Source

How to Monitor Power and Loss ...................................93

iii

Page 6

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

How to Control the Light Source .................................. 97

Use the Display to Control the Main 

Tester’s Light Source ................................................ 98

Use the Module’s Button to Control the 

Light Source ............................................................. 98

Chapter 7 Test Results

View Saved Results ......................................................... 101

How to Add a Result to a Saved Result ........................ 104

How to Replace a Saved Result that Failed .................. 105

Delete, Rename, and Move Results ............................... 106

Manage Results on a Flash Drive ................................... 107

Upload Results to a PC ................................................... 108

View the Memory Status ............................................... 110

Chapter 8 Projects

Why Use Projects? .......................................................... 111

Set Up a Project .............................................................. 112

The PROJECT Screen ....................................................... 112

The CABLE ID SETUP Screen ........................................... 115

About Next ID Sets ......................................................... 115

Manage Projects on a Flash Drive ................................. 118

Copy Project Settings to Other Testers ......................... 119

Chapter 9 Maintenance

Maintenance ................................................................... 121

Verify Operation ............................................................ 122

Clean the Tester ............................................................. 122

Clean the DI-1000 Video Probe ..................................... 122

Traceable Calibration Period ......................................... 123

Page 7

See Information About the Tester .................................123

Update the Software ......................................................123



Extend the Life of the Battery .......................................128

Store the Tester ...............................................................128

Remove the Battery ........................................................128

Calibration .......................................................................129

If the Tester Does Not Operate as Usual .......................129

Options and Accessories .................................................130

Certifications and Compliance .......................................131

Regulatory Information ..................................................131

Appendix A: Reference Method Names

Appendix B: Modified 1 Jumper Reference Method

Contents

Page 8

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

Page 9

List of Figures

Figure Page

1. Main Tester Connectors, Keys, and LEDs 

(CFP-QUAD module shown) ........................................... 10

2. Remote Tester Connectors, Keys, and LEDs 

(CFP-QUAD module shown) ........................................... 12

3. The Home Screen for CertiFiber Pro Modules............... 15

4. LEDs Show the Remote’s Battery Status........................ 19

5. Connections to See the Status of the Remote’s 

Battery ............................................................................. 20

6. How to Zoom the Screen................................................ 22

7. FIX LATER, TEST AGAIN, and TEST Buttons and 

the TEST Key.................................................................... 24

8. How to Remove and Install the Connector Adapters... 28

9. How to Install a Strap and Use the Hand Strap ............ 29

10. How to Remove and Install a Module ........................... 30

11. Examples of Clean and Dirty Fiber Endfaces................. 33

12. Equipment to Clean and Inspect Fiber Endfaces .......... 35

13. How to Use the IBC OneClick Cleaner ........................... 37

14. How to Prevent Damage to the EF-TRC Fiber Cables ... 46

15. Screen to Set the Number of Connectors, 

Splices, and Jumpers ....................................................... 52

16. How to Count the Numbers of Connectors, 

Splices, and Jumpers ....................................................... 54

17. Equipment for Autotests in Smart Remote Mode ........ 56

18. Connections for Smart Remote Mode

(1 Jumper Reference, Multimode Fiber)........................ 58

vii

Page 10

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

19. Result for Smart Remote Mode (Unsaved 

Bi-Directional Results Shown) .........................................62

20. Equipment for Autotests in Loopback Mode.................65

21. Connections for Loopback Mode

(1 Jumper Reference, Multimode Fiber).........................67

22. Result for Loopback Mode..............................................70

23. Equipment for Autotests in Far End Source Mode........73

24. Connections for Far End Source Mode

(1 Jumper Reference Multimode Fiber)..........................76

25. Result for Far End Source Mode .....................................79

26. Equipment for the FiberInspector Test ..........................83

27. FiberInspector Image with Measurement Scales

(fiber with 50 µm core shown) .......................................86

28. Equipment for Visual Fault Locator Tests ......................90

29. How to Use the Visual Fault Locator ..............................92

30. Equipment for Power Meter Measurements .................94

31. Connections to Monitor Power and Loss .......................95

32. Power Meter Measurements and Controls ....................96

33. Light Source Controls for the Main Tester .....................99

34. RESULTS Screen ................................................................102

35. How to Connect the Tester to a PC ................................109

36. PROJECT Screen ...............................................................113

37. CABLE ID SETUP Screen

(after you enter the first and last IDs) ............................116

38. How to Connect the Tester to a PC ................................125

39. How to Connect Units Together to Update 

the Software ....................................................................127

40. How to Remove the Battery ...........................................129

B-1. Modified 1 Jumper Reference Method for 

Smart Remote Mode .......................................................136

viii

Page 11

Chapter 1: Get Acquainted

Overview of the CertiFiber Pro Optical Loss Test Set Modules

The Fluke Networks CertiFiber® Pro Optical Loss Test Set (OLTS) modules attach to Versiv

rugged, hand-held testers that let you certify, troubleshoot, and document optical fiber cabling installations. The testers include these features:

 Measures optical power loss and length on dual-fiber,

multimode cabling at 850 nm and 1300 nm (CFP-MM) or on dual-fiber singlemode cabling at 1310 nm and 1550 nm (CFP-SM). The four-wavelength module (CFP-QUAD) measures at 850 nm, 1300 nm, 1310 nm, and 1550 nm.

 Interchangeable connector adapters on input and output

ports let you make reference and test connections that agree with ISO standards for most SFF (small form factor) connectors.

 Visual fault locator helps you find breaks, bad splices, and

bends and verify fiber continuity and polarity.

 You can save approximately 30,000 fiber test results in the

tester’s internal memory. You can save more results on a removable flash drive.

™

main and remote units to make

Page 12

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

Contact Fluke Networks

www.flukenetworks.com

support@flukenetworks.com

+1-425-446-4519

Fluke Networks PO Box 777 Everett, WA 98206-0777 USA

 Australia: 61 (2) 8850-3333 or 61 (3) 9329 0244

 Beijing: 86 (10) 6512-3435

 Brazil: 11 3759 7600

 Canada: 1-800-363-5853

 Europe: +31-(0) 40 2675 600

 Hong Kong: 852 2721-3228

 Japan: 03-6714-3117

 Korea: 82 2 539-6311

 Singapore: +65-6799-5566

 Taiwan: (886) 2-227-83199

 USA: 1-800-283-5853

Visit our website for a complete list of phone numbers.

Register Your Product

Registering your product with Fluke Networks gives you access to valuable information on product updates, troubleshooting tips, and other support services. To register, fill out the online registration form on the Fluke Networks website at

www.flukenetworks.com.

Page 13

Chapter 1: Get Acquainted

Technical Reference Handbook

The Versiv Technical Reference Handbook has more information about the tester. The Handbook is on the Versiv Product Manuals CD included with your product, and on the Fluke Networks website.

Additional Resources

The Fluke Networks Knowledge Base answers common questions about Fluke Networks products and provides articles on cable testing techniques and technology.

To access the Knowledge Base, log on to www.flukenetworks.com, then click SUPPORT > Knowledge Base.

Supplements and Updated Manuals

If necessary, Fluke Networks will put a supplement for this manual, or an updated manual, on the Fluke Networks website. To see if a supplement or updated manual is available, log on to

www.flukenetworks.com, click SUPPORT > Manuals, then select a

product.

Kit Contents

The CertiFiber Pro kits come with the accessories in the lists below. If something is damaged or missing, contact the place of purchase immediately.

Page 14

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

CFP-100-M Kit

 Versiv main and remote units with battery packs

 Two CertiFiber Pro Multimode Optical Loss Test Set (OLTS)

Modules for tests at 850 nm and 1300 nm

 Two encircled flux test reference cords (EF-TRCs) for 50 µm/

125 µm fiber, SC/LC connectors

 Two test reference cords for 50 µm/125 µm fiber, LC/LC

 Two LC/LC a d a pters

 Carrying case for the testers

 Case for the test reference cords

 Two hand straps for the testers

 USB cable for PC communications, type A USB to Micro-B USB

 Two AC adapter/chargers

 CertiFiber Pro Getting Started Guide

 Versiv Product Manuals CD

 LinkWare Software CD

CFP-100-S Kit

 Versiv main and remote units with battery packs

 Two CertiFiber Pro Singlemode Optical Loss Test Set (OLTS)

Modules for tests at 1310 nm and 1550 nm

 Two test reference cords for singlemode fiber, SC/LC

 Two test reference cords for singlemode fibers, LC/LC

 Two LC/LC adapters

 Carrying case for the testers

 Case for the test reference cords

 Two hand straps for the testers

Page 15

Chapter 1: Get Acquainted

Kit Contents

 USB cable for PC communications, type A USB to Micro-B USB

 Two AC adapter/chargers

 CertiFiber Pro Getting Started Guide

 Versiv Product Manuals CD

 LinkWare Software CD

CFP-100-Q Kit

 Versiv main and remote units with battery packs

 Two CertiFiber Pro Quad Optical Loss Test Set (OLTS) Modules

for tests at 850 nm, 1300 nm, 1310 nm and 1550 nm

 Two encircled flux test reference cords (EF-TRCs) for 50 µm/

125 µm fiber, SC/LC

 Two test reference cords for 50 µm/125 µm fiber, LC/LC

 Two test reference cords for singlemode fiber, SC/LC

 Two test reference cords for singlemode fiber, LC/LC

 Two LC/LC adapters

 Carrying case for the testers

 Case for the test reference cords

 Two hand straps for the testers

 USB cable for PC communications, type A USB to Micro-B USB

 Two AC adapter/chargers

 CertiFiber Pro Getting Started Guide

 Versiv Product Manuals CD

 LinkWare Software CD

Page 16

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

CFP-Q-ADD Kit

 Two CertiFiber Pro Quad Optical Loss Test Set (OLTS) Modules

for tests at 850 nm, 1300 nm, 1310 nm and 1550 nm

 Two encircled flux test reference cords (EF-TRCs) for 50 µm/

125 µm fiber, SC/LC

 Two test reference cords for 50 µm/125 µm fiber, LC/LC

 Two test reference cords for singlemode fiber, SC/LC

 Two test reference cords for singlemode fiber, LC/LC

 Two LC/LC adapters

 Carrying case for the testers

 Case for the test reference cords

 CertiFiber Pro Getting Started Guide

 Versiv Product Manuals CD

Page 17

Chapter 1: Get Acquainted

Safety Information

Table 1 shows the international electrical symbols used on the tester or in this manual. Symbols for certifications and compliance are on page 131.

: This key turns the tester on and off.

Table 1. International Electrical Symbols

Warning: Risk of fire, electric shock, or personal injury.



Warning or Caution: Risk of damage or destruction to equipment



or software. See explanations in the manuals.

Warning: Class 1 (OUTPUT port) and Class 2 (VFL port) lasers. Risk of



eye damage from hazardous radiation.

Do not put products containing circuit boards into the garbage.



Dispose of circuit boards in accordance with local regulations.

Warning

To prevent possible fire, electric shock, or personal injury:

 Use only AC adapters approved by Fluke Networks

for use with the tester to supply power to the tester and charge the battery.

 Do not put the battery pack in a fire or an

environment with temperatures more than 140 °F (60 °C).

 Do not use the tester in damp or wet environments.

 Do not short-circuit or disassemble the battery pack.

 Do not use the tester if it is damaged. Inspect the

tester before use.

 Do not open the case; no user-serviceable parts are

inside.

 Do not modify the tester.

Page 18

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

 If this equipment is used in a manner not specified

by the manufacturer, the protection provided by the equipment can possibly be impaired.

Warning: Class 1 and Class 2 Laser Products

To prevent possible eye damage caused by hazardous radiation:

 Do not look directly into optical connectors. Some

optical equipment emits invisible radiation that can cause permanent damage to your eyes.

 Keep the module’s OUTPUT ports covered with a

dust cap or keep a test reference cord attached. The OUTPUT ports can emit radiation even when you do not do a test.

 Do not run any tests that activate the outputs on

the tester unless a fiber is attached to the output.

 When you inspect fiber endfaces, use only

magnification devices that have the correct filters.

 Use of controls, adjustments, or procedures not

stated herein can possibly result in hazardous radiation exposure.



Caution

To prevent damage to the tester or cables under test and to prevent data loss:

 Do not connect the tester to an active network.

Doing so causes unreliable test results, can disrupt network operations, and can cause damage to the module’s receiver.

 Use proper cleaning procedures to clean all fiber

connectors before every use. Neglecting this step or using improper procedures can cause unreliable test results and may permanently damage the connectors. See Chapter 6.

Page 19

Chapter 1: Get Acquainted

Safety Information

 Use a video probe to periodically inspect the

module’s optical connectors for scratches and other damage.

 To make sure your test results are as accurate as

possible, do the reference procedure frequently. See “About the Reference for Fiber Tests” on page 42.

 Use only high-quality test reference cords that

comply with the standards. See “About Test Reference Cords and Mandrels” on page 44

 Connect the AC adapter or replace the battery as

soon as the low battery indication appears.

 Keep modules attached to the main and remote

Versiv units to give protection to the module connectors.

 Do not remove the USB flash drive while the LED on

the drive flashes. Doing so can corrupt the data on the drive.

 You can lose a USB flash drive, cause damage to it,

or accidentally erase the contents of the drive. Thus, Fluke Networks recommends that you save no more than one day of test results on a flash drive.

Page 20

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

Connectors, Keys, and LEDs



G H

GPU123.EPS

Figure 1. Main Tester Connectors, Keys, and LEDs (CFP-QUAD module

shown)

 LCD display with touchscreen

 Singlemode output port with removable connector adapter

and dust cap. This port transmits optical signals for loss and length measurements.

Page 21

Chapter 1: Get Acquainted

Connectors, Keys, and LEDs

The LED below the output port is red when the port transmits 1310 nm and green for 1550 nm.

 Input port with removable connector adapter and dust cap.

This port receives optical signals for loss, length, and power measurements.

 Multimode output port with removable connector adapter and

dust cap. This port transmits optical signals for loss and length measurements.

The LED below the output port is red when the port transmits 850 nm and green for 1300 nm.

 Universal fiber connector (with dust cap) for the visual fault

locator. The connector accepts 2.5 mm ferrules. The LED below the connector shows the locator’s mode.

 Button to manually control the output ports ( and ) and the

visual fault locator (

).

 Micro-AB USB port: This USB port lets you connect the tester to a

PC so you can upload test results to the PC and install software updates in the tester.

 Type A USB port: This USB host port lets you save test results on a

USB flash drive or connect a video probe to the tester.

 Headset jack

 : Starts a test. To start a test, you can also tap TEST on the

display.

 : Power key

 : Press  to go to the home screen.

 Connector for the AC adapter. The LED is red when the battery

charges, and green when the battery is fully charged. The LED is yellow if the battery will not charge. See “Charge the Battery” on page 18.

 RJ45 connector: For functions available in future software

releases.

Page 22

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

 Decal with laser safety

information.



Figure 2. Remote Tester Connectors, Keys, and LEDs (CFP-QUAD

module shown)

GPU136.EPS

Page 23

Chapter 1: Get Acquainted

Connectors, Keys, and LEDs

 PASS LED comes on when a test passes.

TEST LED comes on during a test. FAIL LED comes on when a test fails. TALK LED comes on when the talk function is on. LOW BATTERY LED comes on when the battery is low.

The LEDs also have these functions:

• Battery gauge (see Figure 4 on page 19)

• Volume indicator for the TALK function

• Progress indicator for software updates

 Singlemode output port with removable connector adapter

and dust cap. This port transmits optical signals for loss and length measurements.

The LED below the output port is red when the port transmits 1310 nm and green for 1550 nm.

 Input port with removable connector adapter and dust cap.

This port receives optical signals for loss, length, and power measurements.

 Multimode output port with removable connector adapter and

dust cap. This port transmits optical signals for loss and length measurements.

The LED below the output port is red when the port transmits 850 nm and green for 1300 nm.

 Universal fiber connector (with dust cap) for the visual fault

locator. The connector accepts 2.5 mm ferrules. The LED below the connector shows the locator’s mode.

 Button to manually control the output ports ( and ) and the

visual fault locator (

).

 Micro-AB USB port: This USB port lets you connect the tester to a

PC so you can install software updates in the tester.

 Headset jack

Page 24

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

 : Starts a test.  : Power key  : Press  to use the headset to speak to the person at

the other end of the link. Press again to adjust the volume. To turn off the talk function, hold down .

 Connector for the AC adapter. The LED is red when the battery

charges, and green when the battery is fully charged. The LED is yellow if the battery will not charge. See “Charge the Battery” on page 18.

 Decal with laser safety

information.

Page 25

Chapter 1: Get Acquainted

G H

The Home Screen for CertiFiber Pro Modules

The home screen (Figure 3) shows important test settings. Before you do a test, make sure these settings are correct.

Figure 3. The Home Screen for CertiFiber Pro Modules

 PROJECT: The project contains the settings for a job and helps

you monitor the status of a job. When you save test results, the tester puts them in the project. Tap the PROJECT panel to edit the project settings, select a different project, or make a new project.

GPU117.EPS

Page 26

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

 Shows a summary of the test results in the project:

The number of tests that passed.

The number of tests that failed.

 The test setup panel shows the settings the tester will use when

you tap TEST or press .

To change these settings, tap the panel, select the test on the

CHANGE TEST screen, tap EDIT, select different settings on the TEST SETUP screen, then tap SAVE. See Table 2 on pages 49 and

50.

Note

You can set up tests for any module that the tester can use, even when no module is attached.

 Next ID: The Next ID panel shows the ID that the tester gives to

the next test results you save. For Smart Remote mode, this panel shows IDs for main tester’s input and output fibers.

Tap Next ID to do these tasks:

 Enter an ID, select a different ID in the ID set, select a

different set of IDs, or make a new set. The tester adds the IDs and ID sets you make to the project that shows on the home screen.

 Turn Auto Save on or off.

 Operator: The name of the person who does the job. You can

enter a maximum of 20 operator names.

 TOOLS: The TOOLS menu lets you set the reference for fiber

tests, see the status of the tester, and set user preferences such as the language and the display brightness.

 SET REF: Tap SET REF to set the reference and verify your test

reference cords for loss/length tests.

 RESULTS: Tap RESULTS to see and manage the results that are

saved in the tester.

Page 27

Chapter 1: Get Acquainted

The Home Screen for CertiFiber Pro Modules

 TEST: Tap TEST to do the test shown in the test setup panel.

 The percentage of the tests in the project that are completed.

The tester uses the number of available IDs to calculate this percentage. See Figure 37 on page 116. % Tested does not show if your project contains only a Next ID list. See “About Next ID Sets” on page 115 for more information about the Next ID list.

 The type of module attached to the tester.

 This icon shows when the input and output ports on the

tester’s CertiFiber Pro module are connected to the ports on the remote’s CertiFiber Pro module and the remote tester is turned on.

 This icon shows when the talk function is on. To use the talk

function:

1 Connect the main and remote testers together through a

duplex fiber link.

2 Connect headsets to the headset jacks on the testers

3 Press the button on one of the headset microphones or

press  on the remote, then speak into the microphone.

Page 28

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

AC Adapter and Battery

You can use the AC adapter (model VERSIV-ACUN) or the lithium ion battery (model VERSIV-BATTERY) to supply power to the tester.

To remove the battery, see “Remove the Battery” on page 128.

Charge the Battery

Before you use the battery for the first time, charge the battery for about 2 hours with the tester turned off.

To charge the battery

Connect the AC adapter to the tester. See item LED near the AC adapter connector is red when the battery charges, and green when the battery is fully charged.

A fully-charged battery operates for approximately 8 hours of typical use. The battery takes approximately 4 hours to fully charge when the tester is turned off.

Notes

You do not need to fully discharge the battery before you recharge it.

The battery will not charge if its temperature is outside the range of 32 °F to 104 °F (0 °C to 40 °C). The LED near the connection for the AC adapter is yellow if the battery will not charge.

 in Figure 1. The

Check the Battery Status

On a main tester

The battery status icon is in the upper-left corner of the screen:

Battery is full.

Battery is approximately half full.

Page 29

Chapter 1: Get Acquainted

84 % - 100 %

67 % - 83 %

51 % - 66 %

34 % - 50 %

18 % - 33 %

0 % - 17 %

AC Adapter and Battery

If the AC adapter is not connected, the red bar shows that the battery is very low. Connect the AC adapter to charge the battery and make sure the tester continues to operate.

The red bar also shows if the AC adapter is connected, but the battery is not installed.

On a remote

The LEDs show the battery status at the end of the power-up sequence, as shown in Figure 4.

GPU102.EPS

Figure 4. LEDs Show the Remote’s Battery Status

Page 30

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

To see more information about the battery status

1 Make the connections shown in Figure 5 and turn on both

testers.

2 Tap TOOLS, then tap Battery Status.

When the AC adapter is not connected, the screen shows the Time Remaining, which is the approximate battery life at the present rate of use.

Figure 5. Connections to See the Status of the Remote’s Battery

GPU134.EPS

Page 31

Chapter 1: Get Acquainted

How to Use the Touchscreen

The touchscreen lets you use fingertip gestures to control the tester. You can also operate the touchscreen with a stylus that is made for projected capacitance touchscreens.

Caution

For correct operation and to prevent damage to the touchscreen:

 Touch the screen only with your fingers or with a

stylus that is made for projected capacitance touchscreens. Do not use too much force.

 Do not touch the screen with sharp objects.

Note

The touchscreen will not respond if you tap it with your fingernail or an incorrect type of stylus or if you wear non-conductive gloves.

To use the touchscreen

 To select an item on the screen, tap the item lightly with your

fingertip.

 To scroll a screen, lightly touch the screen then move your

fingertip in the direction you want the screen to move.

 On FiberInspector screens, use the pinch and reverse-pinch

gestures to change the magnification on the screen. See Figure 6.

To clean the touchscreen, turn off the tester, then use a soft, lintfree cloth that is moist with a mild detergent.

Caution

When you clean the touchscreen, do not let liquid get under the plastic around the touchscreen.

Page 32

CertiFiber Pro Fiber Optical Loss Test Set

To quickly go back to 1:1 magnification, double-tap the screen.

To zoom in, use the reversepinch gesture

To zoom out, use the pinch gesture

To move the image, drag it in any direction.

Users Manual

Figure 6. How to Zoom the Screen

HGD45.EPS

Page 33

Chapter 1: Get Acquainted

Verify Operation

The tester does a self test when you turn it on. If the tester shows an error or does not turn on, refer to “If the Tester Does Not Operate as Usual” on page 129.

Change the Language

On the home screen, tap the TOOLS icon, tap Language, then tap a language.

Buttons to Do Tests and Save Results

When a test is completed and more than one button shows at the bottom of the screen, the tester highlights one in yellow to recommend which one to tap. Figure 7 shows the buttons you will see.

Note

To change the Auto Save setting, tap the Next ID panel on the home screen.

Page 34

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

HGD40.EPS

Figure 7. FIX LATER, TEST AGAIN, and TEST Buttons and the TEST Key

 SAVE (yellow), TEST (gray): These buttons show if the test

passed and Auto Save is off. When you tap SAVE, you can save the results with an ID that you make or select. When you tap TEST, you can select to save the results or do the test again and not save the results.

 UNSAVED RESULT: This button shows if Auto Save is off and

you go to the home screen when a test is completed. Tap this button to see the result.

 FIX LATER: This button shows if the test failed and Auto Save is

off. Tap FIX LATER to save the results with an ID that you make or select.

Page 35

Chapter 1: Get Acquainted

Overview of Memory Functions

 TEST AGAIN: This button shows if the test failed. Tap this button

to do the test again for the same ID. If Auto Save is on, the tester saves subsequent results with the same ID. If Auto Save is off, you can save the result if necessary. When you look at a saved result that failed, tap TEST AGAIN to do the test again for the same ID and with the same test settings as the saved result.

 TEST (yellow): This button shows if the test passed and Auto

Save is on. When Auto Save is on, the tester saves results with the next available ID when the test is completed. When you tap TEST, the tester does a test for the next available ID.

 : Press  to do the test shown on the home screen for

the Next ID.

Overview of Memory Functions

You can save approximately 30,000 fiber Autotest results.

The capacity available for test results depends on the space used by the software and custom test limits in the tester.

To see the memory status

On the home screen, tap the TOOLS icon, then tap Memory Status.

To make more memory available, you can export results to a USB flash drive, then delete the results in the tester. See “Manage Results on a Flash Drive” on page 107.

Page 36

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

Options for Cable IDs

When you save the test results for a cable, you usually give the results the name that is the ID for the cable. There are several methods you can use to make IDs for test results:

 You can use the CABLE ID SETUP screen to make a set of

sequential IDs. The tester uses the IDs in sequence as the names for the results you save. When Auto Save is on, the tester automatically saves each result with the next available ID in the set. See Chapter 8.

A cable ID set also lets you use IDs again so you can add different results to tests you saved before.

 You can enter an ID each time you do a test. To do this, turn

off the Auto Save function (see page 27). Each time a test is completed, tap SAVE (if the test passed) or FIX LATER (if the test failed), then enter an ID manually.

 You can use LinkWare software to make a set of IDs,

download the set to the tester, then import it into a project.

 After you do a test, you can enter the ID for a test you saved

before. This lets you replace results or add different results to a test you saved before.

 If the test failed before, and you saved the results, you can

select it on the RESULTS screen, then press TEST AGAIN to replace the results for that ID.

Notes

Cable IDs are case-sensitive. For example, the tester saves result with the names “A0” and “a0” in two different records.

A cable ID can have a maximum of 60 characters.

If you delete all the ID sets in a project, the tester makes a default set that starts with 001.

Page 37

Chapter 1: Get Acquainted

How to Remove and Install the Connector Adapters

To turn the Auto Save function on or off

1 On the home screen, tap the Next ID panel.

2 On the CHANGE ID screen, tap the On/Off control next to

Auto Save.

3 Tap DONE.

How to Remove and Install the Connector Adapters

You can change the connector adapters on the input ports of the modules to connect to SC, ST, LC, and FC fiber connectors. You can remove the adapter on the output port to clean the fiber endface in the port. See Figure 8.

Page 38

CertiFiber Pro Fiber Optical Loss Test Set

Keep extra adapters in the containers provided.

Caution

Do not touch the photodiode lens.

Caution

Turn only the collar on the adapter. Do not use tools to remove or install the adapters.

Slot

Key

Slot

Put the key into the slot before you turn the collar on the adapter.

Users Manual

Figure 8. How to Remove and Install the Connector Adapters

GPU135.EPS

Page 39

Chapter 1: Get Acquainted

How to Install a Strap

Two types of straps are available for the tester: a hand strap that helps you hold the tester, and an optional carrying strap that lets you carry and hang the tester. Figure 9 shows how to install a strap and how to use the hand strap.

Figure 9. How to Install a Strap and Use the Hand Strap

How to Remove or Install a Module

Figure 10 shows how to remove and install the module.

Note

It is not necessary to turn off the tester before you remove or install a module.

HGD43.EPS

Page 40

CertiFiber Pro Fiber Optical Loss Test Set

Removal

Installation

Caution

To prevent damage to the case, push the latches down () before you turn them (

).

Users Manual

Figure 10. How to Remove and Install a Module

HGD20.EPS

Page 41

Chapter 1: Get Acquainted

About LinkWare and LinkWare Stats Software

The LinkWare Cable Test Management software included with your tester lets you upload test records to a PC, organize and examine test results, print professional-quality test reports, and do software updates and other maintenance procedures on your tester.

Updates to LinkWare software are available on the Fluke Networks website.

The LinkWare Stats Statistical Report software that is included with LinkWare software provides statistical analysis of cable test reports and generates browsable, graphical reports.

For instructions about LinkWare and LinkWare Stats software, see the guides for getting started and the online help available under Help on the LinkWare and LinkWare Stats menus.

Page 42

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

Page 43

Chapter 2: How to Clean Fiber

Cleaned and polished correctly Wiped on a shirt

Dirty connector on

a patch cord

Contamination that remains

after alcohol dries

Endfaces

When a fiber optic link does not operate correctly, the cause is frequently a dirty endface in a connector. Figure 11 shows examples of dirty endfaces and an endface that has been correctly cleaned and polished.

Figure 11. Examples of Clean and Dirty Fiber Endfaces

GPU36.EPS

Page 44

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

Always clean and inspect the endfaces in fiber connectors before you make connections. Fluke Networks recommends that you use a mechanical device, such as the Fluke Networks IBC OneClick Cleaner, to clean connectors. If you do not have such a device, or if the device does not clean the connector sufficiently, use other optical-grade supplies to clean connectors.

Figure 12 shows the equipment you use to clean and inspect fiber endfaces.

Warning

To prevent possible eye damage caused by hazardous radiation:

 Do not look directly into optical connectors. Some

optical equipment emits invisible radiation that can cause permanent damage your eyes.

 Before you clean an endface, turn off any optical

sources (laser or LED) that are connected to the fiber.

 When you inspect endfaces, use only magnification

devices that have the correct filters.



Caution

To prevent damage to connectors and to keep contamination off of endfaces:

 Always cover unused connectors and adapters with

protective caps.

 Always keep unused protective caps in a clean,

sealed container to prevent contamination.

Page 45

Chapter 2: How to Clean Fiber Endfaces

GPU49.EPS

 Versiv main unit with CertiFiber

Pro module installed

 Video probe with USB connector

(DI-1000 shown)

Figure 12. Equipment to Clean and Inspect Fiber Endfaces

 Fiber cleaning supplies  AC adapter with line cord

(optional)

Page 46

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

How to Use a Fluke Networks IBC OneClick Cleaner

Caution

To prevent damage to the device and to connectors and to keep contamination off of endfaces, read all instructions and obey all safety precautions given in the instructions for the device you use to clean connectors.

To clean the connectors on test reference cords, use wipes and solvent. The OneClick cleaner cleans the fiber core, but can leave contamination around the core. The contamination can move to the core when you make connections. See “To Clean Connector Ends” on page 39.

1 Use the video probe to inspect the connector. If it is dirty,

continue to step 2.

2 To clean a bulkhead connector, remove the cap. To clean the

connector on a fiber cable, remove only the tip of the cap.

3 If necessary for a bulkhead connector, extend the tip of the

device.

4 Push the device straight into the connector until you hear a

loud click. See Figure 13. Then remove the device.

5 Use the video probe to inspect the connector. If necessary,

clean and inspect the connector again.

If the mechanical device does not clean the connector sufficiently, use a swab and solvent to clean the connector.

Page 47

Chapter 2: How to Clean Fiber Endfaces

CLICK!

How to Use a Fluke Networks IBC OneClick Cleaner

Figure 13. How to Use the IBC OneClick Cleaner

GPU16.EPS

Page 48

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

How to Use Wipes, Swabs, and Solvent

Caution

To prevent damage to connectors and to keep contamination off of endfaces:

 Always discard wipes or swabs after you use them.

 Do not let solvent dry on an endface. Some solvents

leave a residue after they dry.

 If you must use alcohol as a solvent, make sure you

use 99%-pure, anhydrous alcohol.

To Clean Bulkhead Connectors

1 Use a video probe to inspect the connector. If it is dirty,

continue to step 2.

2 Touch the tip of a fiber optic solvent pen or swab soaked in

solvent to a lint-free dry wipe or fiber cleaning card.

3 Touch a new, dry swab to the solvent spot on the wipe or

card. Push the swab into the connector, twist it around 3 to 5 times against the end-face, then remove and dispose of the swab.

4 Dry the connector with a dry swab by twisting it around in the

connector 3 to 5 times.

5 Use a video probe to inspect the connector. If necessary, clean

and inspect the connector again.

Page 49

Chapter 2: How to Clean Fiber Endfaces

How to Use Wipes, Swabs, and Solvent

To Clean the Optical Connectors on the Modules

To clean the optical connectors on the modules, first use the procedure given under “To Clean Bulkhead Connectors”.

If a connector is very dirty or the procedure above does not make it clean, use this procedure:

1 Unscrew the adapter on the connector.

2 Clean the ferrule or photodiode lens with a dry, optical-grade

wipe made for fiber optic connectors.

3 Use a video probe to inspect the connector. If necessary, clean

and inspect the connector again.

4 If the connector stays dirty, use a wipe that is moist with

optical-grade solvent to clean the endface. Dry the ferrule or lens with a dry wipe.

To Clean Fiber Adapters

At regular intervals, clean fiber adapters with a swab and fiber optic solvent. Dry with a dry swab.

To Clean Connector Ends

1 Use a video probe to inspect the connector. If it is dirty,

continue to step 2.

2 Touch the tip of a fiber optic solvent pen or swab soaked in

solvent to a lint-free dry wipe or fiber cleaning card.

3 Wipe the connector end-face across the solvent spot, then

back and forth once across the dry area of the wipe or card.

4 Use a video probe to inspect the connector. If necessary, clean

and inspect the connector again.

Note

For some connector types, such as VF-45, it is necessary to use a different method to clean the endface.

Page 50

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

Page 51

Chapter 3: How to Certify Fiber

Cabling

Warning

Before you use the tester, read the safety information that starts on page 7.

Requirements for Reliable Fiber Test Results

To get reliable fiber test results and make sure your tester meets its accuracy specifications, you must use the correct procedures:

 Use proper cleaning procedures to clean all fiber connectors

before every use. See Chapter 2.

 Set the reference frequently. See “About the Reference for

Fiber Tests” on page 42.

 Use only test reference cords that comply with ISO/IEC

14763-3. Measure the loss of the cords frequently. See “About Test Reference Cords and Mandrels” on page 44.

 For multimode fiber, make sure you use the encircled flux test

reference cords (EF-TRCs) or standard mandrels correctly. See “About the EF-TRC (Encircled-Flux Test Reference Cords)” on page 44 and “About Standard Mandrels” on page 47.

 Keep the tester’s software current. The latest software is

available on the Fluke Networks website. See “Update the Software” on page 123.

 Make sure you select the correct fiber type and test limit for

the job, and the index of refraction for the fiber is correct. See Table 2 on page 49.

 Make sure the battery is fully charged.

Page 52

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

 Send the modules to a Fluke Networks service center every 12

months for factory calibration.

About the Reference for Fiber Tests

The reference procedure for fiber cable sets a baseline power level for loss measurements. If the power level that enters the fiber from the source changes, the reference and your loss measurements will be incorrect. The power level can change, for example, when the temperature at the job site increases or decreases or when you disconnect then reconnect a test reference cord at the tester’s output port. So, it is important to set the reference frequently.

When to Set the Reference

Note

At the job site, turn on the testers and let them sit for a minimum of 5 minutes before you set the reference. Let them sit longer if they are above or below ambient temperature.

The tester requires you to set the reference at these times:

 When you change the CertiFiber Pro module in the main or

remote tester.

 When you use a different remote tester.

 When you change the Reference Method in the test setup.

Set the reference also at these times:

 At the start of each day, at the job site, then at regular

intervals during the day. For example, set the reference when you start tests on a different series of fibers.

 When you connect a test reference cord to the module’s

output port or to another source, even if you connect the same test reference cord you connected before.

 When the tester tells you that the reference is out of date.

Page 53

Chapter 3: How to Certify Fiber Cabling

Requirements for Reliable Fiber Test Results

 When a loss measurement is negative. This occurs when there

was a problem when you set the reference. For example, an endface was dirty or the testers were cold.

Caution

Do not disconnect the test reference cords from the modules’ output ports after you set the reference. If you do, you will change the amount of optical power that enters the fiber and the reference will not be correct.

Good Reference Values

Reference values must be in these ranges:

 Multimode 50/125 µm fiber: -19.4 dBm to -26.5 dBm

 Multimode 62.5/125 µm fiber: -17.5 dBm to -23.0 dBm

 Singlemode fiber: -1.0 dBm to -6.0 dBm

If your reference value is outside of the applicable range given above, clean and inspect all connectors then set the reference again. Do this even if the tester lets you use the value.

If your test reference cords and connectors are in good condition, and you use the correct procedure to set the reference, the reference value will not change by more than approximately

0.4 dBm.

Page 54

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

How to See the Reference Values

 After you set the reference, tap View Reference on the SET

REFERENCE screen.

 After you do an Autotest, tap the result window for a fiber,

then tap VIEW REFERENCE.

About Test Reference Cords and Mandrels

Use only test reference cords (TRCs) that have low loss:

 Maximum loss for multimode TRCs: 0.15 dB

 Maximum loss for singlemode TRCs: 0.25 dB

To make sure your test results are accurate as possible:

 Inspect the endfaces of the TRCs every 24 to 48 tests and clean

them when necessary.

 Use the TRC VERIFICATION wizard available for the 1 Jumper

and 3 Jumper reference methods to measure the losses of the TRCs. The losses of the TRCs are included in the loss measurements for links, so you must make sure the losses are very small. The wizard saves the results of the TRC tests to show that your TRCs were good. IDs for these results start with “TRC”, show the date and time of the test, and have an for the test result.

About the EF-TRC (Encircled-Flux Test Reference Cords)

The CFP-MM and CFP-QUAD kits includes the EF-TRC (encircled flux test reference cords), which have signal conditioners on the cords. When you use the EF-TRCs with the CertiFiber Pro multimode modules, your tester complies with IEC 61280-4-1, ISO/ IEC 14763-3, and TIA-526-14-B standards for encircled flux. Measurements made with compliant equipment change less than 10 % for losses of 1 dB or more when you make them at different times or with different equipment that is also compliant.

Page 55

Chapter 3: How to Certify Fiber Cabling

Requirements for Reliable Fiber Test Results

Note

The IEC 61280-4-1, ISO/IEC 14763-3, and TIA-526-14-B standards require your optical loss test set to comply with encircled flux standards at 850 nm with 50 µm/125 µm fiber. The standards recommend compliance at 850 nm with 62.5 µm/ 125 µm fiber and at 1300 nm with 50 µm/125 µm and 62.5 µm/125 µm fiber.

Caution

To prevent damage to fiber connectors, to prevent data loss, and to make sure that your test results are as accurate as possible:

 Use the EF-TRC cords only with the CertiFiber Pro

modules or with sources approved by Fluke Networks for use with the cords. If a source does not have the correct LED and internal fibers, the EF-TRC cords will not make launch conditions that agree with encircled flux standards.

 When you use the EF-TRCs, DO NOT use other

mandrels.

 Always follow the handling guidelines given in

Figure 14.

 Put protective caps on all connectors when you do

not use them.

 Use EF-TRCs that have the fiber core dimension

(50 µm or 62. µm) and type of connectors (SC, ST, LC, or FC) that are the same as the fiber link. Do not use EF-TRCs with hybrid patch cords to connect to links that have other types of connectors.

Page 56

CertiFiber Pro Fiber Optical Loss Test Set

Minimum bend diameter:

1.2 in (30 mm)

Users Manual

Figure 14. How to Prevent Damage to the EF-TRC Fiber Cables

GPU157.EPS

About APC Connectors

When you do tests on links with APC (angled physical contact) connectors, use only test reference cords with APC connectors on the ends connected to the link. If you connect non-APC connectors to the link, the connectors will cause large reflections that make loss measurements inaccurate.

For tests on links with APC connectors, use test reference cords with APC connectors on the ends connected to the tester’s input ports. This is necessary for the 1 jumper reference method. You can connect APC connectors to the tester’s input ports because the fiber does not touch the lens on the input port.

Connect only UPC connectors to the tester’s output ports.

Page 57

Chapter 3: How to Certify Fiber Cabling

Requirements for Reliable Fiber Test Results

About Standard Mandrels

Standard mandrels make measurements of multimode power loss more reliable than if you use no mandrels, but the measurements do not comply with the standards for encircled flux. Fluke Networks recommends that you always use only the EF-TRCs with the CertiFiber Pro multimode modules so that your measurements comply with EF standards.

If you must do tests in Far End Source mode with a different multimode source, and the source is not approved by Fluke Networks for use with the TRCs, use standard mandrels. Make sure you use the size of mandrel that is correct for 50 µm or

62.5 µm fiber, and read all instructions for the source and mandrel.

Caution

If you use mandrels for tests on multimode fiber, do not use test reference cords made from bendinsensitive fiber. The mandrels possibly will not remove all of the modes that can make your loss measurements unreliable.

Page 58

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

Settings for Fiber Tests

Table 2 gives descriptions of the settings for fiber tests. To set up a project, which includes the settings in Table 2, cable IDs, and operator names, see Chapter 8.

To set up a fiber test

1 On the home screen, tap the test setup panel.

2 On the CHANGE TEST screen, select a fiber test to change,

then tap EDIT.

Or to set up a new fiber test, tap NEW TEST. If no module is installed, the MODULE screen shows. Tap the correct CertiFiber Pro module.

3 On the TEST SETUP screen, tap the panels to change settings

for the test. See Table 2.

4 On the TEST SETUP screen, tap SAVE when your test setup is

completed.

5 On the CHANGE TEST screen, make sure the button next to

the test is selected, then tap USE SELECTED.

Page 59

Chapter 3: How to Certify Fiber Cabling

Settings for Fiber Tests

Table 2. Settings for Fiber Tests

Setting Description

Module Select the CertiFiber Pro module you will use.

Test Type Use Smart Remote mode for tests on duplex-fiber

cabling. See page 55.

Use Loopback mode for tests on patch cords and cable spools. See page 64.

Use Far End Source mode for tests on individual fibers. See page 72.

Bi-Directional Off: The tester does fiber tests in only one direction.

On: The tester does fiber tests in both directions. See “Bi-

Directional Tests” on page 80.

The

Bi-Directional setting is not available for Far End

Source mode.

Fiber Type Select a fiber type that is correct for the type you will

test. To see a different group of fiber types, tap MORE, then tap a group. To make a custom fiber type, tap Custom in the Fiber Groups list. See the Technical Reference Handbook.

Fiber Type Settings

Test Limit Select the correct test limit for the job. To see a different

IOR: The tester uses the index of refraction to calculate

the optical length of the fiber. Each fiber type includes the value specified by the manufacturer. To use a different IOR, make a custom fiber type. See the Technical Reference Handbook.

group of limits, tap MORE, then tap the name of a group. To make a custom limit, tap Custom in the Limit Groups list. See the Technical Reference Handbook.

-continued-

Page 60

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

Table 2. Settings for Fiber Tests (continued)

Reference Method

On the No. of Connectors/Splices screen, set the number of jumpers you will use in each fiber path when you set the reference. The dotted lines in the diagram on the screen show you which parts of the link are included in the test results.

The number of jumpers you use has these effects on loss measurements:

1 Jumper: Loss measurements include the connections at both ends of the link. The figures in this manual show 1

Jumper connections.

2 Jumper: Loss measurements include one connection at

one end of the link.

3 Jumper: Loss measurements do not include the connections at the ends of the link. The tester measures only the loss of the fiber.

This setting does not change the loss measurements, but it can change the PASS/FAIL result for test limits that use a calculated loss limit. For all test limits, the tester saves this setting to show the reference method you used.

Caution

Most cable manufacturers will give you a warranty on a fiber installation only if you use the 1 Jumper reference method when you certify the installation.

Note

Different standards use different names for the three methods. See Appendix A.

Connector Type Select the type of connector, such as SC or LC, used in the

cabling. The tester saves this setting to record the type of connector you used. This setting does not change your test results or any of the diagrams that the tester shows. If the correct type is not in the list, select General.

Page 61

Chapter 3: How to Certify Fiber Cabling

Settings for Fiber Tests

Table 2. Settings for Fiber Tests (continued)

No. of Connectors/ Splices

The Total Connections and Splices settings are applicable only if the selected test limit uses a calculated limit for loss.

Total Connections: Enter the total number of connections that are in each path of the link. Do not adjust the number for the Reference Method you use. For example, if the link has 3 connections, enter “3” even if you use the 2 or 3 Jumper reference method. When the tester calculates the loss limit, it automatically removes the losses of the connections you used to set the reference.

Note

The CertiFiber Pro automatically adjusts the number of connections for the Reference Method you use. This is different from the DTX CableAnalyzer, where you do not include the reference connections in the number of connectors.

Splices: Enter the number of splices in each path of the link.

Jumper Reference: Enter the number of jumpers you will use in each fiber path when you set the reference. The dotted lines in the diagram on the screen show you which parts of the link are included in the test results. See Reference Method above.

Figure 15 shows the No. of Connectors/Splices screen. Figure 16 shows how to count the jumpers, connectors, and splices for this setting.

TRC LENGTH (Test reference cord length)

You can enter length of your test reference cords when you set the reference. To enter this value, tap TRC LENGTH on the SET REFERENCE screen. The length you enter does not change the test results. The tester saves the length with the results to meet TIA reporting requirements.

Page 62

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

Figure 15. Screen to Set the Number of Connectors, Splices, and

Jumpers

 Total Connections: Enter the total number of connections that

are in each path of the link. Do not adjust the number for the Reference Method you use. For example, if the link has 3 connections, enter “3” even if you use the 2 or 3 Jumper reference method. When the tester calculates the loss limit, it automatically removes the losses of the connections you used to set the reference.

 Splices: Enter the number of splices that are in each path of the

link.

GPU140.EPS

Page 63

Chapter 3: How to Certify Fiber Cabling

Settings for Fiber Tests

 Jumper Reference: Enter the number of jumpers you will use in

each fiber path when you set the reference. The dotted lines in the diagram on the screen show you which parts of the link are included in the test results. See Reference Method on page 50.

 The dotted lines show you which parts of the link are included in

the test results.

 Connector icons show the connections between the ends of the

link. If you enter 7 or more for the Total Connections setting, a number inside of a connector icon shows the number of connectors between the ends of the link. For example, if the Total Connections setting is 7, a connector icon shows the number 5 ( )

 The round icon shows the number of splices in each path of the

link.

 To see help for the screen, tap .

 To save your settings, tap DONE.

Page 64

CertiFiber Pro Fiber Optical Loss Test Set

Test connections

Total Connections: 3 

(do not adjust for the reference method)

Splices: 1

Connector or connection =

1 connector pair

Connector

Splice

Connector

Reference connections

Jumpers: 1

Connectors

included in the

test results for

the 1 Jumper

reference

method

Users Manual

Figure 16. How to Count the Numbers of Connectors, Splices, and

Jumpers

GPU133.EPS

Page 65

Chapter 3: How to Certify Fiber Cabling

About 1 Jumper Reference Connections

The reference and test connections shown in this manual give 1 jumper results. 1 jumper results include the loss of the fiber plus the loss of the connections at both ends of the link. This is the best method for tests on premises fiber installations. Premises installations typically use patch cords at both ends of the link, and connector loss is a large part of the total loss.

If you do not have the correct connector adapters, see Appendix B for other connections that give 1 jumper results.

For descriptions of the 2 and 3 jumper reference connections, see the Versiv Technical Reference Handbook.

Caution

Most cable manufacturers will give you a warranty on a fiber installation only if you use a 1 Jumper reference when you certify the installation.

Note

If you use a 2 Jumper reference, the Wizard for the reference procedure does not show steps for the TRC verification. To save test results for the TRCs, do the tests manually.

Autotest in Smart Remote Mode

Use Smart Remote mode to do tests on dual-fiber cabling.

In this mode, the tester measures loss and length on two fibers at two wavelengths. If you turn on the Bi-Directional function, the tester makes measurements in both directions.

Figure 17 shows the equipment for tests in Smart Remote mode.

Page 66

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

 Main and remote Versiv units

with CertiFiber Pro modules installed

 For multimode fiber: two EF-TRC

test reference cords

 Two singlemode adapters  For multimode fiber: two test

reference cords. For singlemode fiber: four test reference cords.

Figure 17. Equipment for Autotests in Smart Remote Mode

 Fiber cleaning supplies  Video probe with USB connector

(DI-1000 shown)

 AC adapters with line cords

(optional)

GPU128.EPS

Page 67

Chapter 3: How to Certify Fiber Cabling

Autotest in Smart Remote Mode

Step 1: Set the Reference in Smart Remote Mode

1-1 Turn on the tester and remote and let them sit for a

minimum of 5 minutes. Let them sit longer if they are above or below ambient temperature.

1-2 Make sure that the home screen shows the correct settings for

the job, and the test type is Smart Remote.

To make sure that other settings are correct, tap the test setup panel, make sure the correct test is selected on the CHANGE TEST screen, then tap EDIT to see more settings. Table 2 on page 49 describes the settings.

1-3 Clean and inspect the connectors on the tester, remote, and

test reference cords.

1-4 On the home screen tap SET REF.

1-5 On the SET REFERENCE screen, tap RUN WIZARD.

Notes

To only set the reference, and not measure the loss of your test reference cords, tap SKIP WIZARD on the SET REFERENCE screen.

Fluke Networks recommends that you measure the loss of your test reference cords each time you set the reference.

1-6 Make the connections to set the reference, as shown on the

screen and in Figure 18, then tap NEXT to see the completed connections.

Notes

The SET REFERENCE screen shows reference connections for the selected reference method. Figure 18 shows connections for a 1 Jumper reference.

When you set the reference, align the testers as shown in Figure 18 to keep the fibers as straight as possible.

-continued-

Page 68

CertiFiber Pro Fiber Optical Loss Test Set

Caution

Do not disconnect the outputs ( and ) after you set the reference.

When you use the EF-TRCs,  DO NOT use other mandrels.

Fiber

link

Test

reference

cord

Test reference cord

*Use the EF-TRCs only with multimode modules.

Fiber Link Test

Reference

TRC Verification

Users Manual

Figure 18. Connections for Smart Remote Mode

(1 Jumper Reference, Multimode Fiber)

GPU122.EPS

Page 69

Chapter 3: How to Certify Fiber Cabling

Autotest in Smart Remote Mode

1-7 To enter the length of the test reference cords you will add to

connect to the link, tap TRC LENGTH on the SET REFERENCE screen. The length you enter does not change the test results. The tester saves the length with the results to meet TIA reporting requirements.

1-8 Tap SET REFERENCE. If you did not use the connection wizard,

go to step 3.

Step 2: Measure the Loss of the Test Reference Cords You Will Add

Caution

If you disconnected a test reference cord from the output of the tester or remote, you must set the reference again to make sure your measurements are reliable.

2-1 On the SET REFERENCE screen, when the reference procedure

is completed, tap NEXT.

2-2 Disconnect the test reference cords from the INPUT ports on

the tester and remote, then use test reference cords and adapters to make the connections to verify the TRCs, as shown on the screen and in Figure 18.

2-3 Tap TRC VERIFICATION. The tester measures and saves the loss

of the test reference cords you added. The IDs for these results start with “TRC”, show the date and time of the test, and have an for the test result.

The tester shows a warning if the loss of a TRC is more than these limits:

 Maximum loss for multimode TRCs: 0.15 dB

 Maximum loss for singlemode TRCs: 0.25 dB

If the tester shows a warning, clean and inspect the connectors on the TRCs in the path that has too much loss, then set the reference and do the TRC verification again.

Page 70

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

Step 3: Do an Autotest in Smart Remote Mode

Caution

If you disconnected a test reference cord from the output of the tester or remote, you must set the reference again to make sure your measurements are reliable.

3-1 On the SET REFERENCE screen, when the set reference or

TRC verification procedure is completed, tap NEXT to see how to connect to the link under test.

3-2 Clean and inspect all the connectors.

3-3 Make the connections to do the test on the fiber link, as shown

on the screen and in Figure 18, then tap HOME.

3-4 Tap TEST on the main tester or press  on the main or

remote tester.

If the CHECK FIBER CONNECTIONS screen shows an open fiber:

 Make sure that all connections are good and no fibers

have damage. Use the VFL to make sure the fibers in the link have continuity.

 Make sure that the remote is on.

 Switch the connections at one end of the patch panel.

 If you are not sure you are connected to the correct

fibers, connect the main tester’s INPUT fiber to different connections until the test continues or the INPUT fiber on the display is green. Then if necessary, connect the remote’s INPUT fiber to different connections until the test continues.

3-5 If Bi-Directional is On: Halfway through the test, the tester

tells you to switch the input and output fibers. See “BiDirectional Tests” on page 80.

Page 71

Chapter 3: How to Certify Fiber Cabling

Autotest in Smart Remote Mode

3-6 Save the result:

 If Auto Save is on, the tester uses the next two IDs to save

the results for the two fibers.

 If Auto Save is off, tap SAVE if the test passed or FIX

LATER if the test failed. The SAVE RESULT screen shows

the next two IDs available. You can change the IDs if necessary.

Autotest Results for Smart Remote Mode

Unsaved results show the results for both fibers. See Figure 19.

Fiber IDs for Saved Results in Smart Remote Mode

If Auto Save is On and the test passed, the tester saves two records, one for each fiber. The records have the next two IDs in the ID list.

If you must change the ID for a fiber before you save results, set

Auto Save to Off before you do the test. Then, on the SAVE RESULT screen, tap the Input Fiber ID or Output Fiber ID window.

Page 72

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

GPU118.EPS

Figure 19. Result for Smart Remote Mode (Unsaved Bi-Directional

Results Shown)

 The overall result for the Autotest.

 The fiber IDs and the loss and length measurements for the

fibers:

The result exceeds the limit.

The result is within the limit.

The selected test limit does not have a limit for the test.

Page 73

Chapter 3: How to Certify Fiber Cabling

Autotest in Smart Remote Mode

To see the results, limits, and margins for a fiber, tap the window.

 The settings the tester used for the test.

 The dashed lines are around the connectors and fiber that are

included in the loss and length results. Gray connectors and fibers are not included because you used them to set the reference.

 Connector icons show the number you entered for the TOTAL

CONNECTIONS setting on the No. of Connectors/Splices screen (Figure 15 on page 52). For Figure 19, the TOTAL CONNECTIONS setting is 4.

 The round icon shows the number of splices entered for the

SPLICES setting on the No. of Connectors/Splices screen.

 To see help for the screen, tap .

 When more than one button shows at the bottom of the screen,

the tester highlights one in yellow to recommend which one to tap. See “Buttons to Do Tests and Save Results” on page 23.

Page 74

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

Autotest in Loopback Mode

Use Loopback mode to do tests on spools of cable and segments of uninstalled cable.

In this mode, the tester measures loss and length at two wavelengths. If you turn on the Bi-Directional function, the tester makes measurements in both directions.

Figure 17 shows the equipment for tests in Loopback Mode.

Page 75

Chapter 3: How to Certify Fiber Cabling

Autotest in Loopback Mode

 Main Versiv unit with CertiFiber

Pro module installed

 For multimode fiber: one EF-TRC

test reference cord

 Two singlemode adapters  For multimode fiber: one test

reference cord. For singlemode fiber: two test reference cords.

Figure 20. Equipment for Autotests in Loopback Mode

GPU129EPS

 Fiber cleaning supplies  Video probe with USB connector

(DI-1000 shown)

 AC adapters with line cords

(optional)

Page 76

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

Step 1: Set the Reference in Loopback Mode

1-1 Turn on the tester and let it sit for a minimum of 5 minutes.

Let it sit longer if it is above or below ambient temperature.

1-2 Make sure that the home screen shows the correct settings for

the job, and the test type is Loopback.

1-3 Clean and inspect the connectors on the tester and test

reference cords.

1-4 On the home screen tap SET REF.

1-5 On the SET REFERENCE screen, tap RUN WIZARD.

Notes

To only set the reference, and not measure the loss of your test reference cord, tap SKIP WIZARD on the SET REFERENCE screen.

Fluke Networks recommends that you measure the loss of your test reference cord each time you set the reference.

1-6 Make the connection to set the reference, as shown on the

screen, then tap NEXT to see the completed connections. Figure 21 also shows the completed connections.

Notes

The SET REFERENCE screen shows reference connections for the selected reference method. Figure 21 shows connections for the 1 Jumper reference.

When you set the reference, keep the fiber as straight as possible.

-continued-

Page 77

Test

reference

cord

Caution

Do not disconnect the output ( ) after you set the reference.

When you use the EF-TRCs,  DO NOT use other mandrels.

Fiber

Fiber Test

Reference

TRC Verification

*Use the EF-TRCs only with multimode modules.

Chapter 3: How to Certify Fiber Cabling

Autotest in Loopback Mode

Figure 21. Connections for Loopback Mode

(1 Jumper Reference, Multimode Fiber)

GPU131.EPS

Page 78

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

1-7 To enter the length of the test reference cord you will add to

connect to the fiber under test, tap TRC LENGTH on the SET REFERENCE screen. The length you enter does not change the test results. The tester saves the length with the results to meet TIA reporting requirements.

1-8 Tap SET REFERENCE.

1-9 If you did not use the connection wizard, go to step 3.

Step 2: Measure the Loss of the Test Reference Cord You Will Add

Caution

If you disconnected the test reference cord from the output of the tester, you must set the reference again to make sure your measurements are reliable.

2-1 On the SET REFERENCE screen, when the reference procedure

is completed, tap NEXT.

2-2 Disconnect the test reference cord from the INPUT port on the

tester, then use a test reference cord and adapter to make the connections to verify the TRCs, as shown on the screen and in Figure 21.

2-3 Tap TRC VERIFICATION. The tester measures and saves the loss

of the test reference cord you added. The ID for this result starts with “TRC”, shows the date and time of the test, and has an for the test result.

The tester shows a warning if the loss of a TRC is more than these limits:

 Maximum loss for multimode TRCs: 0.15 dB

 Maximum loss for singlemode TRCs: 0.25 dB

If the tester shows a warning, clean and inspect the connectors on the TRC, then set the reference and do the TRC verification again.

Page 79

Chapter 3: How to Certify Fiber Cabling

Autotest in Loopback Mode

Step 3: Do an Autotest in Loopback Mode

Caution

If you disconnected the test reference cord from the output of the tester, you must set the reference again to make sure your measurements are reliable.

3-1 On the SET REFERENCE screen, when the set reference or

TRC verification procedure is completed, tap NEXT to see how to connect to the fiber under test.

3-2 Clean and inspect the connectors on the fiber under test.

3-3 Make the connections to do the test on the fiber, as shown on

the screen and in Figure 21, then tap HOME.

3-4 Tap TEST on the main tester or press  on the main or

remote tester.

If the CHECK FIBER CONNECTIONS screen shows an open fiber:

 Make sure that all connections are good and no fibers

have damage. Use the VFL to make sure the fiber under test has continuity.

 If you are connected to fibers at a patch panel that are

connected together at the far end, and you are not sure you are connected to the correct fibers, connect the main tester’s INPUT fiber to different connections until the test continues.

3-5 If Bi-Directional is On: Halfway through the test, the tester

tells you to switch the input and output fibers. See “BiDirectional Tests” on page 80.

3-6 If Auto Save is on, the tester uses the next ID to save the

results.

If Auto Save is off, the SAVE RESULT screen shows the next ID available. You can change the ID if necessary.

Page 80

CertiFiber Pro Fiber Optical Loss Test Set

E F

Users Manual

Autotest Results for Loopback Mode

Figure 22 shows an example of Autotest results for Loopback mode.

Figure 22. Result for Loopback Mode

 The overall result for the Autotest.

 The loss and length measurements for the fiber:

The result exceeds the limit.

The result is within the limit.

The selected test limit does not have a limit for the test.

GPU119.EPS

Page 81

Chapter 3: How to Certify Fiber Cabling

Autotest in Loopback Mode

To see the results, limits, and margins for the fiber, tap the window.

 The settings the tester used for the test.

 The dashed lines are around the connectors and fiber that are

included in the loss and length results. Gray connectors and fibers are not included because you used them to set the reference.

 Connector icons show the number you entered for the TOTAL

CONNECTIONS setting on the No. of Connectors/Splices screen (Figure 15 on page 52). For Figure 22, the TOTAL CONNECTIONS setting is 3.

 The round icon shows the number of splices entered for the

SPLICES setting on the No. of Connectors/Splices screen.

 To see help for the screen, tap .

 When more than one button shows at the bottom of the screen,

the tester highlights one in yellow to recommend which one to tap. See “Buttons to Do Tests and Save Results” on page 23.

Page 82

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

Autotest in Far End Source Mode

Use Far End Source mode to measure loss at two wavelengths on one fiber.

In this mode, you can use the CertiFiber Pro remote or another source, such as the Fluke Networks SimpliFiber

far end of the fiber.

Pro source, at the

Caution

For Far End Source mode, use the EF-TRC cords only with the CertiFiber Pro modules or with sources approved by Fluke Networks for use with the cords. If a source does not have the correct LED and internal fibers, the EF-TRC cords will not make launch conditions that comply with encircled flux standards. If the source is not approved, use a standard mandrel.

Figure 23 shows the equipment for tests in Far End Source mode.

Auto Wavelength Modes

CertiFiber Pro modules and SimpliFiber Pro sources have an auto wavelength mode. In this mode, the output port transmits both wavelengths (850 nm and 1300 nm or 1310 nm and 1550 nm). The signal includes identifiers that tell the meter when to measure power at each wavelength. The CertiFiber Pro module in the remote always operates in auto wavelength mode.

To select Auto CertiFiber Pro or Auto SimpliFiber Pro mode, you tap the setting when the tester shows the TEST MODE window. The TEST MODE window shows each time you set the reference.

Page 83

Chapter 3: How to Certify Fiber Cabling

Autotest in Far End Source Mode

 Main and remote Versiv units

with CertiFiber Pro modules installed

 For multimode fiber: one EF-TRC

test reference cord

 One singlemode adapter  For multimode fiber: one test

reference cord. For singlemode fiber: two test reference cords.

Figure 23. Equipment for Autotests in Far End Source Mode

 Fiber cleaning supplies  Video probe with USB connector

(DI-1000 shown)

 AC adapters with line cords

(optional)

GPU130.EPS

Page 84

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

Step 1: Set the Reference in Far End Source Mode

1-1 Turn on the tester and source let them sit for a minimum of

5 minutes. Let them sit longer if they are above or below ambient temperature, or if the instructions for the source specify a longer time.

1-2 Make sure that the home screen shows the correct settings for

the job, and the test type is Far End Source.

1-3 Clean and inspect the connectors on the tester, source, and test

reference cords.

1-4 On the home screen tap SET REF.

1-5 In the TEST MODE window, select Auto CertiFiber Pro or the

type of source you will use, then tap DONE.

1-6 On the SET REFERENCE screen, tap RUN WIZARD.

Notes

To only set the reference, and not measure the loss of your test reference cord, tap SKIP WIZARD on the SET REFERENCE screen.

Fluke Networks recommends that you measure the loss of your test reference cord each time you set the reference.

1-7 Make the connections to set the reference as shown on the

screen, then tap NEXT to see the completed connections. Figure 24 also shows the completed connections.

Notes

The SET REFERENCE screen shows reference connections for the selected reference method. Figure 24 shows connections for the 1 Jumper reference.

Page 85

Chapter 3: How to Certify Fiber Cabling

Autotest in Far End Source Mode

When you set the reference, keep the fiber as straight as possible.

1-8 Turn on the optical source. On the CertiFiber Pro remote

module, hold down the button adjacent to the VFL port for 3 seconds to turn on the multimode source.

On CFP-QUAD modules, to turn on the singlemode source, press the button again.

Note

The CertiFiber Pro module in the remote always operates in auto wavelength mode. The output port transmits both wavelengths (850 nm and 1300 nm or 1310 nm and 1550 nm). The signal includes identifiers that tell the main tester when to measure power at each wavelength.

1-9 To enter the length of the test reference cord you will add to

1-10 Tap SET REFERENCE.

1-11 If you did not use the connection wizard, go to step 3.

Page 86

CertiFiber Pro Fiber Optical Loss Test Set

EF-TRC*

Caution

Do not disconnect the output ( ) after you set the reference.

When you use the EF-TRCs,  DO NOT use other mandrels.

Fiber

Test

reference

cord

*Use the EF-TRCs only with multimode modules.

Fiber Test

Reference

TRC Verification

Users Manual

Figure 24. Connections for Far End Source Mode

(1 Jumper Reference Multimode Fiber)

GPU132.EPS

Page 87

Chapter 3: How to Certify Fiber Cabling

Autotest in Far End Source Mode

Step 2: Measure the Loss of the Test Reference Cord You Will Add

Caution

If you disconnected the test reference cord from the output of the tester, you must set the reference again to make sure your measurements are reliable.

2-1 On the SET REFERENCE screen, when the reference procedure

is completed, tap NEXT.

2-2 Disconnect the test reference cord from the INPUT port on the

tester, then use a test reference cord and adapter to make the connections to verify the TRCs, as shown on the screen and in Figure 24.

2-3 Tap TRC VERIFICATION. The tester measures and saves the loss

of the test reference cord you added. The ID for this result starts with “TRC”, shows the date and time of the test, and has an for the test result.

The tester shows a warning if the loss of a TRC is more than these limits:

 Maximum loss for multimode TRCs: 0.15 dB

 Maximum loss for singlemode TRCs: 0.25 dB

If the tester shows a warning, clean and inspect the connectors on the TRC, then set the reference and do the TRC verification again.

Step 3: Do an Autotest in Far End Source Mode

Caution

If you disconnected the test reference cord from the output of the tester, you must set the reference again to make sure your measurements are reliable.

Page 88

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

3-1 On the SET REFERENCE, when the set reference or TRC

verification procedure is completed, tap NEXT to see how to connect to the fiber under test.

3-2 Clean and inspect the all connectors.

3-3 Make the connections to do the test on the fiber, as shown on

the screen and in Figure 24, then tap HOME.

3-4 Tap TEST on the main tester or press  on the main or

remote tester.

3-5 If the CHECK FIBER CONNECTIONS screen shows an open

fiber:

 Make sure that all connections are good and no fibers

have damage. Use the VFL to make sure the fiber under test has continuity.

 If you are connected to a fiber at a patch panel, and you

are not sure you are connected to the correct fiber, connect the main tester’s INPUT fiber to different connections until the test continues.

3-6 If Auto Save is on, the tester uses the next ID to save the

results.

If Auto Save is off, the SAVE RESULT screen shows the next ID available. You can change the ID if necessary.

Autotest Results for Far End Source Mode

Figure 25 shows an example of Autotest results for Far End Source mode.

Note

The Autotest in Far End Source mode does not show a PASS/FAIL result, limit, or margin if the selected test limit uses fiber length to calculate loss. An example of such a limit is the TIA-568C Fiber Backbone limit. The tester does not measure length in Far End Source mode.

Page 89

E F

Chapter 3: How to Certify Fiber Cabling

Autotest in Far End Source Mode

Figure 25. Result for Far End Source Mode

 The overall result for the Autotest.

 The loss and length measurements for the fiber:

The result exceeds the limit.

The result is within the limit.

The selected test limit does not have a limit for the test.

To see the results, limit, and margins for the fiber, tap the window.

 The settings the tester used for the test.

GPU120.EPS

Page 90

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

 The dashed lines are around the connectors and fiber that are

included in the loss and length results. Gray connectors and fibers are not included because you used them to set the reference.

 Connector icons show the number you entered for the TOTAL

CONNECTIONS setting on the No. of Connectors/Splices screen (Figure 15 on page 52). For Figure 25, the TOTAL CONNECTIONS setting is 1.

 The round icon shows the number of splices entered for the

SPLICES setting on the No. of Connectors/Splices screen.

 To see help for the screen, tap .

 When more than one button shows at the bottom of the screen,

the tester highlights one in yellow to recommend which one to tap. See “Buttons to Do Tests and Save Results” on page 23.

Bi-Directional Tests

A connector or splice can have a different loss when you measure from the other end of the fiber. Thus, some manufacturers of fiber cable and components will not give you warranty support unless you do bi-directional tests. Do bi-directional tests when they are required by the manufacturer or by your customer.

The tester can automatically do bi-directional tests in Smart Remote and Loopback modes. To get bi-directional results in Far End Source mode, do a test from each end of the fiber.

In Smart Remote mode, the tester saves bi-directional results in two records. Each record contains the results for one fiber for both directions.

To do a bi-directional test

1 On the home screen, tap the test setup panel, make sure the

correct test is selected on the CHANGE TEST screen, then tap EDIT.

2 On the TEST SETUP screen, in the Bi-Directional panel, tap the

control to make it show On, then tap SAVE.

Page 91

Chapter 3: How to Certify Fiber Cabling

Bi-Directional Tests

3 Do an Autotest.

4 Halfway through the test, the tester tells you to switch the

input and output fibers.

Caution

Switch the connections at both ends of the patch panel or fiber under test, not at the tester's and remote’s ports. If you disconnect a test reference cord from an output port on the tester or remote, the reference value will be unreliable.

Note

The directions Main>Remote (main to remote) and Remote>Main (remote to main) in the bidirectional results are only the directions of the optical signals for the second half of the test. If a fiber fails, the direction does not tell you the location of the problem.

5 If Auto Save is on and the tester is in Smart Remote mode, the

tester uses the next two IDs to save the results for the two fibers.

If Auto Save is off, the SAVE RESULT screen shows the next two IDs available. You can change the IDs if necessary.

Page 92

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

Page 93

Chapter 4: The FiberInspector Test

The optional DI-1000 video probe connects to the type A USB port on the Versiv main unit to let you inspect the endfaces in fiber optic connectors. The probe lets you see dirt, scratches, and other defects that can cause unsatisfactory performance or failures in fiber optic networks.

How to Do the FiberInspector Test

Figure 26 shows the equipment for a FiberInspector test.

 Versiv main unit with CertiFiber

Pro module installed

 Video probe with USB connector

(DI-1000 shown)

Figure 26. Equipment for the FiberInspector Test

GPU49.EPS

 Fiber cleaning supplies  AC adapter with line cord

(optional)

Page 94

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

To do the FiberInspector test

1 Connect the probe to the type A USB port on the side of the

tester.

2 Make sure the correct tip is on the probe.

3 Clean the connector that you will inspect.

4 Do the FiberInspector test:

To do the FiberInspector test when it is in the project

a. On the home screen, tap the test setup panel.

b. On the CHANGE TEST screen, tap the FiberInspector test,

then tap USE SELECTED.

c. Tap Test or press .

To do the FiberInspector test when it is not in a project

On the home screen, tap the TOOLS icon, then tap FiberInspector.

Page 95

Chapter 4: The FiberInspector Test

How to Do the FiberInspector Test

5 Insert the probe into the connector.

6 To adjust the focus, turn the knob on the probe clockwise or

counterclockwise.

Note

The button on the DI-1000 probe has no function when you use the probe with the Versiv unit.

7 To save the image, tap SAVE.

8 On the SAVE RESULT screen, select End 1 or End 2, make sure

the Cable ID and End name are correct, then tap SAVE.

Saved FiberInspector results show these icons for End 1 and End 2:

Notes

The Auto Save function does not operate with the FiberInspector test.

Continuous use of the video probe decreases the battery life. To increase the battery life, connect the ac adapter when you use the probe for more than a few minutes.

Page 96

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

Figure 27. FiberInspector Image with Measurement Scales

(fiber with 50 µm core shown)

Note To see the buttons for the measurement axes and core scales and to change the magnification of the

screen, you must first tap to put the screen in still mode.

 You can use the round, horizontal, and vertical scales to

measure the size of the fiber core and cladding. You can also measure the size of particles, scratches, and other defects on the endface.

GPU25.EPS

Page 97

Chapter 4: The FiberInspector Test

How to Do the FiberInspector Test

To show the scales, tap SCALE ON ().

 Outer, blue ring: 250 µm cladding

 Middle, green rings: 120 µm and 130 µm

 Inner, yellow rings: 25 µm and 62.5 µm (to change the size,

tap NEXT SCALE)

 To adjust the brightness or contrast of the image, tap , then

move the bars on the controls. To hide the controls, tap again.

 To show the scales (), tap , then tap SCALE ON. To change

the size of the measurement ring for the fiber core, tap NEXT SCALE.

 To give a PASS or FAIL grade to the image, tap GRADE. See .

 To put the screen in still mode and turn off the probe, tap .

Tap to turn on the probe again.

 To give the image a grade of PASS or FAIL, tap GRADE (). If you

set the grade to FAIL, then save the image, the ID for the image is in the list of tests to do again.

To zoom in and out, tap to put the screen in still mode, then use the pinch, reverse-pinch, and double-tap gestures on the touchscreen. See Figure 6 on page 22.

Page 98

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

Page 99

Chapter 5: The Visual Fault Locator

Visual Fault Locator Applications

The CertiFiber Pro modules include a visual fault locator that sends a red light down the fiber. The red light shows at the end of the fiber and at breaks, cracks, and sharp bends along the fiber.

The VFL also helps you quickly verify the continuity of fibers, identify connectors, and find faults along fibers and in connectors.

The VFL helps you do these tasks:

 Quickly verify the continuity of fibers.

 Identify the polarity of duplex connections.

 Identify connections in patch panels.

 See breaks and bad splices. These faults cause the fiber to

emit red light.

 See high-loss bends. If you can see the light from the VFL

at a bend in a fiber, the bend is too sharp.

 See connectors that have damaged fibers inside. A

damaged fiber inside a connector causes a red light in the connector.

 Increase the quality of mechanical splices and pre-

polished connectors: Before you seal the splice or connector, adjust the fiber alignment for the minimum amount of light where the fibers touch. (Refer to the instructions from the manufacturer when you make splices and connectors.)

Page 100

CertiFiber Pro Fiber Optical Loss Test Set

Users Manual

How to Use the VFL

Figure 28 shows the equipment for tests with the visual fault locator.

GPU137.EPS

 Versiv main unit with CertiFiber

Pro module installed

 One patch cord to connect the

tester to the fiber (optional)

Figure 28. Equipment for Visual Fault Locator Tests

 Video probe with USB connector

(DI-1000 shown)

 Fiber cleaning supplies  AC adapter with line cord

(optional)

Fluke CertiFiber Pro, CFP-100-M, CFP-100-S, CFP-Q-ADD, CFP-100-Q User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

LIMITED WARRANTY AND LIMITATION OF LIABILITY

Contents

List of Figures

Chapter 1: Get Acquainted

Overview of the CertiFiber Pro Optical Loss Test Set Modules

Contact Fluke Networks

Register Your Product

Technical Reference Handbook

Additional Resources

Supplements and Updated Manuals

Kit Contents

CFP-100-M Kit

CFP-100-S Kit

CFP-100-Q Kit

CFP-Q-ADD Kit

Safety Information

Connectors, Keys, and LEDs

The Home Screen for CertiFiber Pro Modules

AC Adapter and Battery

Charge the Battery

Check the Battery Status

How to Use the Touchscreen

Verify Operation

Change the Language

Buttons to Do Tests and Save Results

Overview of Memory Functions

Options for Cable IDs

How to Remove and Install the Connector Adapters

How to Install a Strap

How to Remove or Install a Module

About LinkWare and LinkWare Stats Software

How to Use a Fluke Networks IBC OneClick Cleaner

How to Use Wipes, Swabs, and Solvent

To Clean Bulkhead Connectors

To Clean the Optical Connectors on the Modules

To Clean Fiber Adapters

To Clean Connector Ends

Requirements for Reliable Fiber Test Results

About the Reference for Fiber Tests

When to Set the Reference

Good Reference Values

How to See the Reference Values

About Test Reference Cords and Mandrels

About the EF-TRC (Encircled-Flux Test Reference Cords)

About APC Connectors

About Standard Mandrels

Settings for Fiber Tests

About 1 Jumper Reference Connections

Autotest in Smart Remote Mode

Step 1: Set the Reference in Smart Remote Mode

Step 2: Measure the Loss of the Test Reference Cords You Will Add

Step 3: Do an Autotest in Smart Remote Mode

Autotest Results for Smart Remote Mode

Fiber IDs for Saved Results in Smart Remote Mode

Autotest in Loopback Mode

Step 1: Set the Reference in Loopback Mode

Step 2: Measure the Loss of the Test Reference Cord You Will Add

Step 3: Do an Autotest in Loopback Mode

Autotest Results for Loopback Mode

Autotest in Far End Source Mode

Auto Wavelength Modes

Step 1: Set the Reference in Far End Source Mode

Step 2: Measure the Loss of the Test Reference Cord You Will Add

Step 3: Do an Autotest in Far End Source Mode

Autotest Results for Far End Source Mode

Bi-Directional Tests

Chapter 4: The FiberInspector Test

How to Do the FiberInspector Test

Chapter 5: The Visual Fault Locator

Visual Fault Locator Applications

How to Use the VFL